This patch adds support for the "amcc,usb-otg" device
which is found in the PowerPC Canyonlands' dts.

The device definition was added by:

commit c89b3458 ("powerpc/44x: Add USB DWC DTS entry to Canyonlands
board")

but without any driver support as the dwc2 driver wasn't available at
that time.

Note: The system can't use the generic "snps,dwc2" compatible
because of the special ahbcfg configuration. The default
GAHBCFG_HBSTLEN_INCR4 of snps,dwc2 can cause a system hang
when the USB and SATA is used concurrently.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch moves the the host_dma initialization
before dwc2_set_param_dma_desc_enable() and
dwc2_set_param_dma_desc_fs_enable(). The reason being
that both function need it.

Fixes: 1205489cee75bf39 ("usb: dwc2: Get host DMA device properties")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Added new core param for low speed, which can be used only when SNPSID
is equal to DWC2_CORE_FS_IOT. When LS mode is enabled, we are
restricting ep types and providing to upper layer only INTR and CTRL
endpoints.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When device is enumerated in LS we should program ep0_mps accordingly.
USB2 spec says that in LS mode, control ep mps must be 8.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add new device IDs for IOT gadget. Done changes in probe to
configure core accordingly depending on device ID value.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Do modifications in dwc2_hsotg_core_init_disconnected() function to
enable USB 1.1 Full-Speed Serial Transceiver Select in GUSBCFG register
if corresponding speed and PHY types are chosen. Adjust device speed
selection in DCFG register as well.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Check if endpoint is enabled during dwc2_hsotg_ep_disable() function
processing and call dwc2_hsotg_ep_stop_xfr() to disable it and flush
associated FIFO.

Move dwc2_hsotg_ep_stop_xfr() and dwc2_hsotg_wait_bit_set() functions
upper before dwc2_hsotg_ep_enable and dwc2_hsotg_ep_disable function
definitions.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Correct dwc2_hsotg_ep_stop_xfr() function to follow dwc2 programming
guide for setting NAK on specific endpoint, disabling it and flushing
corresponding FIFO.

Current code does not take into account whether core acts in shared or
dedicated FIFO mode, current endpoint is periodic or not. It does not
clear EPDISBLD interrupt after programming of DXEPCTL_EPDIS, does not
flush shared TX FIFO and tries to clear global out NAK in wrong manner
instead of setting DCTL_CGOUTNAK.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Tests with various hosts show that depend on time difference between
host sending SETUP packet and IN/OUT token SW could get Xfercomplete
interrupt without SetUp interrupt. On the other hand, SW should parse
received SETUP packet only after ensuring that Host has moved to either
Data or Status stage of control transfer.

For this purpose added checking in the dwc2_hsotg_epint() function to
not handle xfercomplete and postpone SETUP packet analysis till SW's
getting of setup phase done interrupt.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In DDMA mode if programmed ISOC OUT transfer length is not DWORD
aligned, after closing descriptor HW leaves value of 4 - (ureq->length %
4) in the RX bytes. This is caused because DMA works using 4B chunks.
Example: if length = 9 and all 9 bytes were received from the bus, after
xfercomplete rx_bytes value is 3. Hence add this value to the amount of
transferred bytes.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Enable the BNA (Buffer Not Available) interrupt in descriptor DMA mode.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

For DDMA mode in case of isochronous transfers completion performed
differently than other transfer types. This is because each usb request
was mapped to one descriptor in the chain and SW gets xfercomplete
interrupt on all descriptors. The endpoint remains enabled until HW
processes last descriptor with "L" bit set or BNA interrupt gets
asserted for IN and OUT endpoints correspondingly.

Add function dwc2_gadget_complete_isoc_request_ddma() - completes one
isochronous request taken from endpoint's queue.

Add function dwc2_gadget_start_next_isoc_ddma() - tries to restart
isochronous endpoint if requests are pending. Check for EPENA. If the
endpoint was disabled, try to restart it after programming descriptor
chain prepared by SW earlier, switch SW to fill the other half of chain.

Add function dwc2_gadget_fill_isoc_desc() - initializes DMA descriptor
for isochronous transfer based on the received request data and endpoint
characteristics.

Added function dwc2_gadget_start_isoc_ddma() - prepare DMA chain for
isochronous transfer in DDMA, programs corresponding DMA address to
DEPDMA, enables the endpoint. This function is called once SW decides to
start isochronous IN or OUT transfer depend on reception of NAK or
OUTTknEPdis interrupts indicating first isochronous token arrival from
host.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In DDMA mode incompISOOUT should be masked, similar as Bulk Out -
XferCompl and BNA should be handled. incompISOIN is not valid in DDMA
and is not getting asserted.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Preparing for isochronous transfers support adding in DDMA mode. In DDMA
isochronous transfers are handled differently compared to Slave and BDMA
modes. This is caused by fact that isoc requests contain data for one
frame/microframe. HW descriptor should contain data of one
frame/microframe as well. Hence each DMA descriptor in the chain will
correspond to one usb request.

Decided to divide endpoints descriptor chain to two halves - while one
will be processed by HW, other one will be under SW control. First part
will be passed to HW once ISOC traffic needs to be started. In parallel
to HW's work SW will keep creating new entries in the other half of
chain if new requests arrive in ep_queue routine. This will allow
passing of already pre-prepared descriptors to HW immediately after
endpoint gets disabled. The endpoint should be disabled once HW closes
descriptor with "L" bit set. Afterwards SW will switch to use first part
of chain if more requests are arriving.

Add two members to the dwc2_hsotg_ep structure to be used in isochronous
transfers' handling in DDMA mode:

-isoc_chain_num - indicates which half of EP descriptor chain can be
		used by SW to add new queued requests while HW is
		processing other half.

-next_desc - index which points to next not yet programmed descriptor in
		the half of descriptor chain which is under SW control.

Also add initialization of these fields in function
dwc2_hsotg_ep_enable().
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add DCFG register field macro for descriptor DMA mode and update core
initialization routine to set that bit accordingly.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In DDMA mode of operation IN status phase of control write transfer
should start after getting StsPhseRcvd interrupt. This interrupt is
issued by HW once host starts to send IN tokens after data stage.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The StsPhseRcvd interrupt should not be enabled in slave mode.

Also move the StsPhsRcvd interrupt checking in the endpoint interrupt
handler to the correct order according to the databook. The interrupt
itself will be implemented in a later commit.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Update transfer starting dwc2_hsotg_start_req() routine with call of
function dwc2_gadget_config_nonisoc_xfer_ddma() to fill descriptor
chain.

Add call of dwc2_gadget_get_xfersize_ddma() in
dwc2_hsotg_handle_outdone() and dwc2_hsotg_complete_in() interrupt
handlers for DDMA mode to get information on transferred data from
descriptors instead of DXEPTSIZ.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add dwc2_gadget_set_ep0_desc_chain() function to switch between EP0 DDMA
chains depend on the stage of control transfer.

Include EP0 DDMA chain selection during ep_queue called from
dwc2_hsotg_enqueue_setup() for setup stage. Selecting and filling DDMA
chain for status phase as well - add calls of
dwc2_gadget_set_ep0_desc_chain() and
dwc2_gadget_config_nonisoc_xfer_ddma() functions.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This property was mistakenly added, then removed, so don't read it in.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

All users are DT-only and it makes no sense to keep
unused code
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Now that all the infrastructure is in place, we can
clear events in the top-half handler in order to
bring IRQ line low ASAP.

This is also a necessary step in order to implement
workaround for known erratum in follow-up patches.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Let's start copying events from evt->buf to
evt->cache and use evt->cache for processing events.

A follow-up patch will be added to clear events in
the top-half handler in order to bring IRQ line low
as soon as possible.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Instead of always accessing the macro directly,
let's rely on evt->length which is the actual length
of current event buffer. While unlikely, we could
change event buffer's size at any time.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This extra buffer will be used so we can copy
triggered events from our event buffer to this cache
and process all of them later in bottom half
handler.

We need this in order to implement a workaround for
a known erratum in recent DWC3 release.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add clock operation at .set_suspend if the PHY has
suspend requirement, it can be benefit of power saving for
phy and the whole system (parent clock may also be disabled).
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

dwc3_soft_reset() is doing the same thing as
dwc3_core_soft_reset(). Let's remove
dwc3_soft_reset() since that's not needed anymore.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Fix error message by checkpath.pl
open brace '{' following struct/enum go on the same line

Patch applied by running fix inplace capability of checkpatch:
checkpatch.pl -f *.[ch] --types OPEN_BRACE --fix-inplace
Signed-off-by: Anson Jacob <ansonjacob.aj@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We have a macro which does the same trick. Let's
use it.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Since usb_endpoint_maxp now returns only lower 11 bits mult
calculation here isn't correct anymore and that breaks webcam
for me. Patch make use of usb_endpoint_maxp_mult instead of
direct calculation.

Fixes: abb62184 ("usb: ch9: make usb_endpoint_maxp() return
       only packet size")
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add a function to check properties and call it from probe. This will
allow us to add check code without bloating the probe function. This
needs to be done after dwc3_get_properties() and dwc3_core_init() so
that all the properties and hardware configs are available.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add a helper function to check if we are running on a DWC_usb3 core.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add DMA descriptor members to the dwc2_hsotg_ep structure.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add dwc2_gadget_get_chain_limit() function and its call in transfer
start routine to correctly estimate one go on transfer size if
descriptor DMA mode is selected.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Rename MAX_DMA_DESC_SIZE to HOST_DMA_NBYTES_LIMIT as it stores value of
host DMA descriptor transfer bytes' limit. Values are different in case
of gadget DMA descriptors.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Update dwc2_hsotg structure to add descriptor chains for EP 0: two DMA
descriptors for Setup phase, per one for IN/OUT data and status phases.
Add their allocation function dwc2_gadget_alloc_ctrl_desc_chains() and
its call during gadget probe.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add device mode DMA transfer descriptor status quadlet field notations.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add a parameter for descriptor DMA and set it based on hardware
capabilities. This won't actually be used by the gadget until later,
when the descriptor DMA code is in place.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Make the DMA descriptor structure packed to guarantee alignment and size
in memory.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Rename DMA descriptor structure from dwc2_hcd_dma_desc to dwc2_dma_desc
as it is applies to both host and gadget.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>