Allow to set a fixed quantization parameter offset between luma and
chroma in the h.264 encoder.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Allow to enable constrained intra prediction in the h.264 encoder.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Allow to add fixed quantization parameter offset between luma and
chroma quantization parameters. This control directly corresponds
to the chroma_qp_index_offset field of the h.264 picture parameter
set.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Allow to enable h.264 constrained intra prediction (macroblocks using
intra prediction modes are not allowed to use residual data and decoded
samples of neighboring macroblocks coded using inter prediction modes).
This control directly corresponds to the constrained_intra_pred_flag
field in the h.264 picture parameter set.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The COM3 register at address 0x0c already defaults to 0x10, the two bits
COM3[7:6] are set according to V4L2 controls by sethvflip later.
There is no need to set it multiple times during bridge initialization.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

This register is later overwritten by set_frame_rate anyway.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The video format, payload size, and frame size setup is video format
and frame size specific. Those registers are overwritten during
bridge_start anyway.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Add support to pass through the sensor's native SGBRG8 bayer pattern,
allowing to cut the required USB bandwidth in half.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

In preparation for adding SGBRG8 as a second video format besides YUYV,
move video format specific register settings from the bridge_init array
into the bridge_start arrays.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

If a driver supports multiple pixel formats with the same frame size,
TRY_FMT will currently always return the first pixel format.
Fix this by adding pixelformat support to wxh_to_nearest_mode().
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

If a driver supports multiple pixel formats with the same frame size,
ENUM_FRAMEINTERVALS will currently only work for the first pixel format.
Fix this by adding pixelformat support to wxh_to_mode().
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

For short waits, usleep_range should be used instead of msleep,
see Documentation/timers/timers-howto.txt.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The buffer arguments to v4l2_m2m_buf_copy_data args were swapped.

The reason is confusing naming conventions in vim2m. It certainly
could be improved.

Fixes: 7aca565e ("media: vim2m: use v4l2_m2m_buf_copy_data")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

v4l2_compliance gave a warning for the S_PARM test for output streams:

warn: v4l2-test-formats.cpp(1235): S_PARM is supported for buftype 2, but not for ENUM_FRAMEINTERVALS

The reason is that vivid mapped s_parm for output streams to g_parm. But if
S_PARM doesn't actually change anything, then it shouldn't be enabled at all.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The video output sizeimage calculation did not take data_offset into account.

This can cause problems with video loopback or exporting output buffers for
use as dmabuf import buffers since the output buffer size is now too small.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

V4L2_BUF_TYPE_META_OUTPUT was added by commit 72148d1a
("media: v4l: Add support for V4L2_BUF_TYPE_META_OUTPUT") but the patch
missed adding the type to the macro telling whether a given type is an
output type or not. Do that now. Getting this wrong leads to handling the
buffer as a capture buffer in a lot of places.

Fixes: 72148d1a ("media: v4l: Add support for V4L2_BUF_TYPE_META_OUTPUT")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

It makes no sense to support the USERPTR memory model if the vivid instance was
configured as dma_contig. Disable it if this is the case.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Jian Xu has left the company. Remove his e-mail address that no longer
works.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Remove Jian Xu from the driver's reviewers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The CSI controller found on the H3 (and H5) is a reduced version of the
one found on the A31. It only has 1 channel, instead of 4 channels for
time-multiplexed BT.656. Since the H3 is a reduced version, it cannot
"fallback" to a compatible that implements more features than it
supports.

Add a compatible string entry for the H3.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The CSI controller found on the H3 (and H5) is a reduced version of the
one found on the A31. It only has 1 channel, instead of 4 channels for
time-multiplexed BT.656. Since the H3 is a reduced version, it cannot
"fallback" to a compatible that implements more features than it
supports.

Split out the H3 compatible as a separate entry, with no fallback.

Fixes: b7eadaa3 ("media: dt-bindings: media: sun6i: Add A31 and H3 compatibles")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Some little style fixup work.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Control handlers registration lacked error path with
v4l2_ctrl_handler_free() call. Fix it by using goto to alread existing
v4l2_ctrl_handler_free() call.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

An array which defines sensor's supported formats is not written anywhere,
so it can be constant.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Some returns were adjoined to unrelated code blocks. This patch adds
a space inbetween.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The driver uses variables to store frame resolutions and to indexing
various arrays. These should be unsigned.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Add missing SPDX identifiers to .c and .h files of the sensor driver.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The soc_camera drivers are marked as orphaned. Add Petr Cvek as a new
maintainer for ov9640 driver after its switch from the soc_camera.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

This patch removes the dependency on an obsoleted soc_camera from ov9640
driver and changes the code to be a standalone v4l2 async subdevice.
It also adds GPIO allocations for power and reset signals (as they are not
handled by soc_camera now).

The values for waiting on GPIOs (reset and power) settling down were taken
from the datasheet (> 1 ms after HW/SW reset). The upper limit was chosen
as an arbitrary value. Also one occurrence of mdelay() was changed to
msleep(). The delays were successfully tested on a real hardware.

The patch makes ov9640 sensor again compatible with the pxa_camera driver.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Initial part of ov9640 transition from soc_camera subsystem to a standalone
v4l2 subdevice. The soc_camera version seems to be used only in Palm Zire72
and in (the future) HTC Magician. On these two devices the support is
broken as pxa_camera driver doesn't use soc_camera anymore. The other
mentions from git grep are "TODOs" (in board-osk.c) or chip names for
unsupported sensors on HW which doesn't use soc_camera at all (irelevant).

Copy the driver files from soc_camera and mark the original ones in the
Kconfig description as obsoleted.

Add config option VIDEO_OV9640 to the build files in drivers/media/i2c.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The following commits:
commit f6dd927f ("[media] media: ov7670: calculate framerate properly for ov7675")
commit 04ee6d92 ("[media] media: ov7670: add possibility to bypass pll for ov7675")
introduced the ability to bypass PLL multiplier and use input clock (xvclk)
as pixel clock output frequency for ov7675 sensor.

PLL is bypassed using register DBLV[7:6], according to ov7670 and ov7675
sensor manuals. Macros used to set DBLV register seem wrong in the
driver, as their values do not match what reported in the datasheet.

Fix by changing DBLV_* macros to use bits [7:6] and set bits [3:0] to
default 0x0a reserved value (according to datasheets).

While at there, remove a write to DBLV register in
"ov7675_set_framerate()" that over-writes the previous one to the same
register that takes "info->pll_bypass" flag into account instead of setting PLL
multiplier to 4x unconditionally.

And, while at there, since "info->pll_bypass" is only used in
set/get_framerate() functions used by ov7675 only, it is not necessary
to check for the device id at probe time to make sure that when using
ov7670 "info->pll_bypass" is set to false.

Fixes: f6dd927f ("[media] media: ov7670: calculate framerate properly for ov7675")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

OV5640 sensor supports raw image output (bayer).
Configure ISP mux/format registers accordingly.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The i2c address for the Omnivision OV5645 camera sensor is 0x3c. It is
incorrectly mentioned as 0x78 in binding. Hence fix that.

Fixes: 09c716af [media] media: i2c/ov5645: add the device tree binding document
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Commit "4adb0a04 media: ov5645: Supported external clock is 24MHz"
modified the external clock frequency to be 24MHz instead of the
23.88MHz in driver. Hence, modify the frequency value in binding.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

This driver doesn't set all members of mbus format field when the
VIDIOC_SUBDEV_{S,G}_FMT ioctls are called.

This is detected by v4l2-compliance.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The VIDIOC_SUBDEV_G_FMT ioctl for this driver doesn't recognize
V4L2_SUBDEV_FORMAT_TRY and always works as if V4L2_SUBDEV_FORMAT_ACTIVE
is specified.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Set default window and format code at probe time instead of always checking
if they have not been set yet when VIDIOC_SUBDEV_G_FMT ioctl is called.

This change simplifies the next patch (make VIDIOC_SUBDEV_G_FMT ioctl work
with V4L2_SUBDEV_FORMAT_TRY).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The description of test patterns 11 and 12 are swapped.

Checked against the live sensor.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The device won't be powered off on systems that have no sensors connected
unless it has a driver bound to it. Allow that to happen even if there are
no sensors connected to cio2.
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@linux.intel.com>
Tested-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

This commit corrects max and step values for v4l2 control for
V4L2_CID_JPEG_RESTART_INTERVAL. Max should be 0xffff and step should be 1.
It was found by using v4l2-compliance tool and checking result of
VIDIOC_QUERY_EXT_CTRL/QUERYMENU test.
Previously it was complaining that step was bigger than difference
between max and min.

Fixes: 15f4bc3b ("[media] s5p-jpeg: Add JPEG controls support")
Signed-off-by: Pawe? Chmiel <pawel.mikolaj.chmiel@gmail.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>