Somehow I added spaces instead of tabs to a few lines in
debugfs.c.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

bail out from the suspend/resume callbacks if
d0i3 is used.

declare support for ANY wowlan trigger (i.e.
normal operation).

On resume, we shouldn't execute the d0i3 exit
flow (which might disconnect stations, etc.)
until mac80211 was resumed.
Add new flags to indicate we are in suspend,
and call the pending exit work on resume.

Since the resume flow can take some time, add
a new EXIT_WORK reference type to prevent going
back to d0i3 at this stage.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Also warn if an older firmware is loaded.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This patch enables Energy Based Scan (EBS) - intended to detect energy
on 5 GHz band channels. Passive scan on this band takes up to 2.64 sec
assuming 110mSec per-channel * 24 channels. EBS is designed to detect
energy on channels with intensive Wifi activity as well as those where
only beacons are transmitted. EBS completes sampling all channels within
shortest beacon frame transmission time. Total EBS duration is about 100
msec (typical beacon interval).
Detecting Wifi activity on 5 GHz band channels can significantly reduce
scan duration thus saving time and power. EBS failure reported by FW
disables EBS for current connection. It is re-enabled upon new
connection attempt on any WLAN interface.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Calling iwl_send_bt_init_conf for INIT firmware is not a
problem, and calling iwl_send_bt_prio_tbl from
iwl_send_bt_init_conf allows us to prepare for new API.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The BT Coex API underwent a minor backward compatible API
change.
We now need to set an invalid value in the override fields.
While at it, add kerneldoc comments on the fields in the
command.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This is really not needed. This is a remainder from a C99
initialiser.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This firmware is not supported any more.
A few code paths specific to old firmware can be removed.
We can now assume that a few TLV flags are always set since
we won't load firmware that didn't support the corresponding
features. This will be done in a separate patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

While the scan_cmd should really be allocated in init (and
we do fail init in case the allocation failed), it doesn't
mean we should lock up the machine if something really bad
happened.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Collect accumulated stats of tx attempts and successes
per rate and column for debugging purposes.
These stats can be read via debugfs file drv_tx_stats
and can also be reset by writing to this file.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

rcu_assign_pointer() ensures that the initialization of a structure is
carried out before storing a pointer to that structure. However, in the
case that NULL is assigned there's no structure to initialize so using
RCU_INIT_POINTER instead is safe and more efficient.
Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
[rewrite commit log]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware doesn't support broadcast filtering on P2P
client. Trying to enable it makes the firmware assert.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When NIC is exiting from thermal throttling state (i.e. after
heating and then cooling down), tx-backoff values are assigned
to be zero, instead of being restored to the minimal value. Fixed.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When NIC exit thermal throttling while having minimal tx-backoff
restriction, the warning message that indicate about that state
won't show up. Fixed.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The Rx FIFO includes valuable data - dump it when the FW
asserts. Also - free the SRAM and Rx FIFO when we create
the file, and don't collect new SRAM / Rx FIFO if the
previous file hasn't been collected through debugfs yet.

Also - add a comment to saying that the ASSERT output should
not be modified since we have automatic scripts that monitor
this output.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This must not happen - otherwise we might keep flushing
forever.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This will be used later to flush / wait for queues that are
related to a specific vif.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Now that mac80211 calls pre_rcu_remove and we set the
fw_id_to_mac_id pointer to -ENOENT before the station is
removed, we don't need to set fw_id_to_mac_id to -EINVAL
when the station is really removed.
Leave fw_id_to_mac_id to be -ENOENT which will let the
drain worker (iwl_mvm_sta_drained_wk) know that this station
is not to be drained.
We don't need to drain this station since it is our AP in
managed mode and we flush all its frames synchronously
anyway.

Setting the AP station to -EINVAL could lead to confusion
since internal stations are also reserved with -EINVAL,
this confusion showed up in the logs as:

Drained sta 0, but it is internal?
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware tells us if an Rx packet was beamformed or not.
Propagate this data to mac80211's rx_status.vht_flags.
The main user of this data is the radiotap header.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This define is related to the firmware packaging and is
needed by more than one transport.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Besides the different allocation flags, they are really
the same. Pass the gfp_t flags as a parameter, and unify
them.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Similar to the recent RX queue patch, this changes the need_update
handling for the TX queues to be clearer and only done when needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When updating the write pointer, the TX queue should be locked
to get consistent state, fix that in the interrupt handler.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of using u8 to hold logic values, use bool.

Also fix a comment, the return value is no longer relevant.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When shadow registers are enabled, then need_update never needs
to be set, so move the need_update handling into the function
that really needs to do it (iwl_pcie_rxq_inc_wr_ptr) and also
separate the check when it woke up. While at it, convert it to
bool.

This also clarifies the locking and means the irq_lock needs to
no longer be held for any such updates.

The irq_lock also doesn't have to be held for restocking since
everything else locks the RX queue properly, so remove that and
finally disentangle the two locks entirely so there aren't any
dependencies between the two left.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Use the new NAPI infrastructure added to mac80211 to get
GRO. We don't really implement NAPI since we don't have
a real poll function and we never schedule a NAPI poll.
Instead of this, we collect all the packets we got from a
single interrupt and then call napi_gro_flush().

This allows us to benefit from GRO. In half duplex medium
like WiFi, its main advantage is that it reduces the number
of TCP Acks, hence improving the TCP Rx performance.

Since we call the Rx path with a spinlock held, remove
the might_sleep mention from the op_mode's API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ido Yariv <ido@wizery.com>
[Squash different patches and rewrite the commit message]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Allow fixing the tx power reduction through debugfs
file.

The change doesn't take affect immediately, but
will be considered the next time tpc is evaluated.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Implement Adaptive Tx Power Control algorithm.

ATPC basically tries to decrease the tx power
as much as possible while the throughput is
not being hurt.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The fw recently added an option to set tx power reduction
per station (in the lq_cmd command), and get the tx power
reduction used (in the tx_resp struct).

Use them and propogate this value up to mac80211's tx
response (in order to use it later in the rate-scaling
algorithm).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>