Make these const as they are only used during a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

The switchtec_ntb driver has a couple requirements on the switchec's
hardware configuration so we add these notes to the documentation.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

The Switchtec hardware has two types of memory windows: LUTs and Direct.
The first area in each BAR is for LUT windows and the remaining area is
for the direct region. The total number of LUT entries is set by a
configuration setting in hardware and they all must be the same
size. (This is fixed by switchtec_ntb to be 64K.)

switchtec_ntb enables the LUTs only for the first BAR and enables the
highest power of two possible. Seeing the LUTs are at the beginning of
the BAR, the direct memory window's alignment is affected. Therefore,
the maximum direct memory window size can not be greater than the number
of LUTs times 64K. The direct window in other BARs will not have this
restriction as the LUTs will not be enabled there. LUTs will only be
exposed through the NTB API if the use_lut_mw parameter is set.

Seeing the Switchtec hardware, by default, configures BARs to be 4G a
module parameter is given to limit the size of the advertised memory
windows. Higher layers tend to allocate the maximum BAR size and this
has a tendency to fail when they try to allocate 4GB of contiguous
memory.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Seeing there is no dedicated hardware for this, we simply add
these as entries in the shared memory window. Thus, we could support
any number of them but 128 seems like enough, for now.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Pretty straightforward implementation of doorbell registers.
The shift and mask were setup in an earlier patch and this just hooks
up the appropriate portion of the IDB register as the local doorbells
and the opposite portion of ODB as the peer doorbells. The DB mask is
protected by a spinlock to avoid concurrent read-modify-write accesses.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

switchtec_ntb checks for a link by looking at the shared memory
window. If the magic number is correct and the other side indicates
their link is enabled then we take the link to be up.

Whenever we change our local link status we send a msg to the
other side to check whether it's up and change their status.

The current status is maintained in a flag so ntb_is_link_up
can return quickly.

We utilize Switchtec's link status notifier to also check link changes
when the switch notices a port changes state.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Add a skeleton NTB driver which will be filled out in subsequent patches.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Set up some hardware registers and creates interrupt service routines
for the doorbells and messages.

There are 64 doorbells in the switch that are shared between all
partitions. The upper 4 doorbells are also shared with the messages
and are therefore not used. Thus, this provides 28 doorbells for each
partition.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Add the code to initialize the memory windows in the hardware.
This includes setting up the requester ID table, and figuring out
which BAR corresponds to which memory window. (Seeing the switch
can be configured with any number of BARs.)

Also, seeing the device doesn't have hardware for scratchpads or
determining the link status, we create a shared memory window that has
these features. A magic number with a version component will be used
to determine if the other side's driver is actually up.

The shared memory window also informs the other side of the
size and count of the local memory windows.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Seeing the Switchtec NTB hardware shares the same endpoint as the
management endpoint we utilize the class_interface API to register
an NTB driver for every Switchtec device in the system that has the
NTB class code.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Adds a comment and a check to ntb_mw_get_align() so that it always fails
if the function is called before the link is up.

Also adds a comment to ntb_mw_count() to note that it may return 0 if
it is called before the link is up.

This is to prevent accidental mis-use in clients that are testing
on hardware that this doesn't matter for.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

With Switchtec hardware it's impossible to get the alignment parameters
for a peer's memory window until the peer's driver has configured its
windows. Strictly speaking, the link doesn't have to be up for this,
but the link being up is the only way the client can tell that
the other side has been configured.

This patch converts ntb_transport and ntb_perf to use this function after
the link goes up. This simplifies these clients slightly because they
no longer have to store the alignment parameters. It also tweaks
ntb_tool so that peer_mw_trans will print zero if it is run before
the link goes up.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

In order for the Switchtec NTB code to handle link change events we
create a notifier callback in the switchtec code which gets called
whenever an appropriate event interrupt occurs.

In order to preserve userspace's ability to follow these events,
we compare the event count with a stored copy from last time we
checked.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

There are two additional regions: ctrl and dbmsg. The first is
for generic NTB control and memory windows. The second is for doorbells
and message registers. This patch also adds a number of related
constants for using these registers.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

We export the class pointer symbol and add an extern define in the
Switchtec header file.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Create the switchtec.h header in include/linux with hardware defines
and the switchtec_dev structure. Both moved directly from switchtec.c.
This is a prep patch for creating an NTB driver for Switchtec.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Removing Jon since he no longer works at Intel.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Pull x86 fixes from Thomas Gleixner:
 "A set of small fixes:

   - make KGDB work again which got broken by the conversion of WARN()
     to #UD. The WARN fixup needs to run before the notifier callchain,
     otherwise KGDB tries to handle it and crashes.

   - disable KASAN in the ORC unwinder to prevent false positive KASAN
     warnings

   - prevent default mapping above 47bit when 5 level page tables are
     enabled

   - make the delay calibration optimization work correctly, which had
     the conditionals the wrong way around and was operating on data
     which was not yet updated.

   - remove the bogus X86_TRAP_BP trap init from the default IDT init
     table, which broke 32bit int3 handling by overwriting the correct
     int3 setup.

   - replace this_cpu* with boot_cpu_data access in the preemptible
     oprofile init code"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/debug: Handle warnings before the notifier chain, to fix KGDB crash
  x86/mm: Fix ELF_ET_DYN_BASE for 5-level paging
  x86/idt: Remove X86_TRAP_BP initialization in idt_setup_traps()
  x86/oprofile/ppro: Do not use __this_cpu*() in preemptible context
  x86/unwind: Disable KASAN checking in the ORC unwinder
  x86/smpboot: Make optimization of delay calibration work correctly

Pull perf tool fixes from Thomas Gleixner:
 "A small set of fixes for perf tool:

   - synchronize the i915 drm header to avoid the 'out of date' warning

   - make sure that perf trace cleans up its temporary files on exit

   - unbreak the build with newer flex versions

   - add missing braces in the eBPF parsing rules"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tooling/headers: Sync the tools/include/uapi/drm/i915_drm.h UAPI header
  perf trace: Call machine__exit() at exit
  perf tools: Fix eBPF event specification parsing
  perf tools: Add "reject" option for parse-events.l

Pull networking fixes from David Miller:

 1) Use after free in vlan, from Cong Wang.

 2) Handle NAPI poll with a zero budget properly in mlx5 driver, from
    Saeed Mahameed.

 3) If DMA mapping fails in mlx5 driver, NULL out page, from Inbar
    Karmy.

 4) Handle overrun in RX FIFO of sun4i CAN driver, from Gerhard
    Bertelsmann.

 5) Missing return in mdb and vlan prepare phase of DSA layer, from
    Vivien Didelot.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  vlan: fix a use-after-free in vlan_device_event()
  net: dsa: return after vlan prepare phase
  net: dsa: return after mdb prepare phase
  can: ifi: Fix transmitter delay calculation
  tcp: fix tcp_fastretrans_alert warning
  tcp: gso: avoid refcount_t warning from tcp_gso_segment()
  can: peak: Add support for new PCIe/M2 CAN FD interfaces
  can: sun4i: handle overrun in RX FIFO
  can: c_can: don't indicate triple sampling support for D_CAN
  net/mlx5e: Increase Striding RQ minimum size limit to 4 multi-packet WQEs
  net/mlx5e: Set page to null in case dma mapping fails
  net/mlx5e: Fix napi poll with zero budget
  net/mlx5: Cancel health poll before sending panic teardown command
  net/mlx5: Loop over temp list to release delay events
  rds: ib: Fix NULL pointer dereference in debug code

Merge tag 'linux-can-fixes-for-4.14-20171110' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2017-11-10

this is a pull request for net/master.

The first patch by Richard Schütz for the c_can driver removes the false
indication to support triple sampling for d_can. Gerhard Bertelsmann's
patch for the sun4i driver improves the RX overrun handling. The patch
by Stephane Grosjean for the peak_canfd driver adds the PCI ids for
various new PCIe/M2 interfaces. Marek Vasut's patch for the ifi driver
fix transmitter delay calculation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2017-11-08

The following series includes some fixes for mlx5 core and etherent
driver.

Sorry for the late submission but as you can see i have some very
critical fixes below that i would like them merged into this RC.

Please pull and let me know if there is any problem.

For -stable:
('net/mlx5e: Set page to null in case dma mapping fails') kernels >= 4.13
('net/mlx5: FPGA, return -EINVAL if size is zero') kernels >= 4.13
('net/mlx5: Cancel health poll before sending panic teardown command') kernels >= 4.13

V1->V2:
	- Fix Reviewed-by tag of the 2nd patch.
	- Drop the FPGA 0 size fix, it needs some more change log info.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After refcnt reaches zero, vlan_vid_del() could free
dev->vlan_info via RCU:

	RCU_INIT_POINTER(dev->vlan_info, NULL);
	call_rcu(&vlan_info->rcu, vlan_info_rcu_free);

However, the pointer 'grp' still points to that memory
since it is set before vlan_vid_del():

        vlan_info = rtnl_dereference(dev->vlan_info);
        if (!vlan_info)
                goto out;
        grp = &vlan_info->grp;

Depends on when that RCU callback is scheduled, we could
trigger a use-after-free in vlan_group_for_each_dev()
right following this vlan_vid_del().

Fix it by moving vlan_vid_del() before setting grp. This
is also symmetric to the vlan_vid_add() we call in
vlan_device_event().
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes: efc73f4b ("net: Fix memory leak - vlan_info struct")
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Girish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Last minute upstream update to one of the UAPI headers - sync it with tooling,
to address this warning:

  Warning: Kernel ABI header at 'tools/include/uapi/drm/i915_drm.h' differs from latest version at 'include/uapi/drm/i915_drm.h'

Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge branch 'perf/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent

Pull perf tooling fixes from Arnaldo Carvalho de Melo.
Signed-off-by: Ingo Molnar <mingo@kernel.org>

The current code does not return after successfully preparing the VLAN
addition on every ports member of a it. Fix this.

Fixes: 1ca4aa9c ("net: dsa: check VLAN capability of every switch")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code does not return after successfully preparing the MDB
addition on every ports member of a multicast group. Fix this.

Fixes: a1a6b7ea ("net: dsa: add cross-chip multicast support")
Reported-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull ceph gix from Ilya Dryomov:
 "Memory allocation flags fix, marked for stable"

* tag 'ceph-for-4.14-rc9' of git://github.com/ceph/ceph-client:
  rbd: use GFP_NOIO for parent stat and data requests

Pull input layer updates from Dmitry Torokhov:

 - a new ACPI ID for Elan touchpad found in yet another Ideapad model

 - Synaptics RMI4 will allow binding to controllers reporting SMB
   version 3 (note that we are not adding any new ACPI IDs to the
   Synaptics PS/2 drover so unless user explicitly enables intertouch
   support there is no user-visible change)

 - a fixup to TSC 2004/5 touchscreen driver to mark input devices as
   "direct" to help userspace identify the type of device they are
   dealing with

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: synaptics-rmi4 - RMI4 can also use SMBUS version 3
  Input: tsc200x-core - set INPUT_PROP_DIRECT
  Input: elan_i2c - add ELAN060C to the ACPI table

Pull KVM fix from Radim Krčmář:
 "Fix PPC HV host crash that can occur as a result of resizing the guest
  hashed page table"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: PPC: Book3S HV: Fix exclusion between HPT resizing and other HPT updates

Pull MIPS fixes from James Hogan:
 "A final few MIPS fixes for 4.14:

   - fix BMIPS NULL pointer dereference (4.7)

   - fix AR7 early GPIO init allocation failure (3.19)

   - fix dead serial output on certain AR7 platforms (2.6.35)"

* tag 'mips_fixes_4.14_2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
  MIPS: AR7: Ensure that serial ports are properly set up
  MIPS: AR7: Defer registration of GPIO
  MIPS: BMIPS: Fix missing cbr address

Following my recent transition from Imagination Technologies to the=20
reincarnated MIPS company add a .mailmap mapping for my work address,
so that `scripts/get_maintainer.pl' gets it right for past commits.
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts commit 941f5f0f.

Sadly, it turns out that we really can't just do the cross-CPU IPI to
all CPU's to get their proper frequencies, because it's much too
expensive on systems with lots of cores.

So we'll have to revert this for now, and revisit it using a smarter
model (probably doing one system-wide IPI at open time, and doing all
the frequency calculations in parallel).
Reported-by: WANG Chao <chao.wang@ucloud.cn>
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Rafael J Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull drm fixes from Dave Airlie:
 "Last few patches to wrap up.

  Two i915 fixes that are on their way to stable, one vmware black
  screen bug, and one const patch that I was going to drop, but it was
  clearly a pretty safe one liner"

* tag 'drm-fixes-for-v4.14-rc9' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: Deconstruct struct sgt_dma initialiser
  drm/i915: Reject unknown syncobj flags
  drm/vmwgfx: Fix Ubuntu 17.10 Wayland black screen issue
  drm/vmwgfx: constify vmw_fence_ops

The CANFD transmitter delay calculation formula was updated in the
latest software drop from IFI and improves the behavior of the IFI
CANFD core during bitrate switching. Use the new formula to improve
stability of the CANFD operation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Markus Marb <markus@marb.org>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch fixes the cause of an WARNING indicatng TCP has pending
retransmission in Open state in tcp_fastretrans_alert().

The root cause is a bad interaction between path mtu probing,
if enabled, and the RACK loss detection. Upong receiving a SACK
above the sequence of the MTU probing packet, RACK could mark the
probe packet lost in tcp_fastretrans_alert(), prior to calling
tcp_simple_retransmit().

tcp_simple_retransmit() only enters Loss state if it newly marks
the probe packet lost. If the probe packet is already identified as
lost by RACK, the sender remains in Open state with some packets
marked lost and retransmitted. Then the next SACK would trigger
the warning. The likely scenario is that the probe packet was
lost due to its size or network congestion. The actual impact of
this warning is small by potentially entering fast recovery an
ACK later.

The simple fix is always entering recovery (Loss) state if some
packet is marked lost during path MTU probing.

Fixes: a0370b3f ("tcp: enable RACK loss detection to trigger recovery")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reported-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a GSO skb of truesize O is segmented into 2 new skbs of truesize N1
and N2, we want to transfer socket ownership to the new fresh skbs.

In order to avoid expensive atomic operations on a cache line subject to
cache bouncing, we replace the sequence :

refcount_add(N1, &sk->sk_wmem_alloc);
refcount_add(N2, &sk->sk_wmem_alloc); // repeated by number of segments

refcount_sub(O, &sk->sk_wmem_alloc);

by a single

refcount_add(sum_of(N) - O, &sk->sk_wmem_alloc);

Problem is :

In some pathological cases, sum(N) - O might be a negative number, and
syzkaller bot was apparently able to trigger this trace [1]

atomic_t was ok with this construct, but we need to take care of the
negative delta with refcount_t

[1]
refcount_t: saturated; leaking memory.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 8404 at lib/refcount.c:77 refcount_add_not_zero+0x198/0x200 lib/refcount.c:77
Kernel panic - not syncing: panic_on_warn set ...

CPU: 0 PID: 8404 Comm: syz-executor2 Not tainted 4.14.0-rc5-mm1+ #20
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:16 [inline]
 dump_stack+0x194/0x257 lib/dump_stack.c:52
 panic+0x1e4/0x41c kernel/panic.c:183
 __warn+0x1c4/0x1e0 kernel/panic.c:546
 report_bug+0x211/0x2d0 lib/bug.c:183
 fixup_bug+0x40/0x90 arch/x86/kernel/traps.c:177
 do_trap_no_signal arch/x86/kernel/traps.c:211 [inline]
 do_trap+0x260/0x390 arch/x86/kernel/traps.c:260
 do_error_trap+0x120/0x390 arch/x86/kernel/traps.c:297
 do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:310
 invalid_op+0x18/0x20 arch/x86/entry/entry_64.S:905
RIP: 0010:refcount_add_not_zero+0x198/0x200 lib/refcount.c:77
RSP: 0018:ffff8801c606e3a0 EFLAGS: 00010282
RAX: 0000000000000026 RBX: 0000000000001401 RCX: 0000000000000000
RDX: 0000000000000026 RSI: ffffc900036fc000 RDI: ffffed0038c0dc68
RBP: ffff8801c606e430 R08: 0000000000000001 R09: 0000000000000000
R10: ffff8801d97f5eba R11: 0000000000000000 R12: ffff8801d5acf73c
R13: 1ffff10038c0dc75 R14: 00000000ffffffff R15: 00000000fffff72f
 refcount_add+0x1b/0x60 lib/refcount.c:101
 tcp_gso_segment+0x10d0/0x16b0 net/ipv4/tcp_offload.c:155
 tcp4_gso_segment+0xd4/0x310 net/ipv4/tcp_offload.c:51
 inet_gso_segment+0x60c/0x11c0 net/ipv4/af_inet.c:1271
 skb_mac_gso_segment+0x33f/0x660 net/core/dev.c:2749
 __skb_gso_segment+0x35f/0x7f0 net/core/dev.c:2821
 skb_gso_segment include/linux/netdevice.h:3971 [inline]
 validate_xmit_skb+0x4ba/0xb20 net/core/dev.c:3074
 __dev_queue_xmit+0xe49/0x2070 net/core/dev.c:3497
 dev_queue_xmit+0x17/0x20 net/core/dev.c:3538
 neigh_hh_output include/net/neighbour.h:471 [inline]
 neigh_output include/net/neighbour.h:479 [inline]
 ip_finish_output2+0xece/0x1460 net/ipv4/ip_output.c:229
 ip_finish_output+0x85e/0xd10 net/ipv4/ip_output.c:317
 NF_HOOK_COND include/linux/netfilter.h:238 [inline]
 ip_output+0x1cc/0x860 net/ipv4/ip_output.c:405
 dst_output include/net/dst.h:459 [inline]
 ip_local_out+0x95/0x160 net/ipv4/ip_output.c:124
 ip_queue_xmit+0x8c6/0x18e0 net/ipv4/ip_output.c:504
 tcp_transmit_skb+0x1ab7/0x3840 net/ipv4/tcp_output.c:1137
 tcp_write_xmit+0x663/0x4de0 net/ipv4/tcp_output.c:2341
 __tcp_push_pending_frames+0xa0/0x250 net/ipv4/tcp_output.c:2513
 tcp_push_pending_frames include/net/tcp.h:1722 [inline]
 tcp_data_snd_check net/ipv4/tcp_input.c:5050 [inline]
 tcp_rcv_established+0x8c7/0x18a0 net/ipv4/tcp_input.c:5497
 tcp_v4_do_rcv+0x2ab/0x7d0 net/ipv4/tcp_ipv4.c:1460
 sk_backlog_rcv include/net/sock.h:909 [inline]
 __release_sock+0x124/0x360 net/core/sock.c:2264
 release_sock+0xa4/0x2a0 net/core/sock.c:2776
 tcp_sendmsg+0x3a/0x50 net/ipv4/tcp.c:1462
 inet_sendmsg+0x11f/0x5e0 net/ipv4/af_inet.c:763
 sock_sendmsg_nosec net/socket.c:632 [inline]
 sock_sendmsg+0xca/0x110 net/socket.c:642
 ___sys_sendmsg+0x31c/0x890 net/socket.c:2048
 __sys_sendmmsg+0x1e6/0x5f0 net/socket.c:2138

Fixes: 14afee4b ("net: convert sock.sk_wmem_alloc from atomic_t to refcount_t")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for the following PEAK-System CAN FD interfaces:

PCAN-cPCIe FD         CAN FD Interface for cPCI Serial (2 or 4 channels)
PCAN-PCIe/104-Express CAN FD Interface for PCIe/104-Express (1, 2 or 4 ch.)
PCAN-miniPCIe FD      CAN FD Interface for PCIe Mini (1, 2 or 4 channels)
PCAN-PCIe FD OEM      CAN FD Interface for PCIe OEM version (1, 2 or 4 ch.)
PCAN-M.2              CAN FD Interface for M.2 (1 or 2 channels)

Like the PCAN-PCIe FD interface, all of these boards run the same IP Core
that is able to handle CAN FD (see also http://www.peak-system.com).
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

SUN4Is CAN IP has a 64 byte deep FIFO buffer. If the buffer is not
drained fast enough (overrun) it's getting mangled. Already received
frames are dropped - the data can't be restored.
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>