Commit f15f05b0 ("crypto: ccm - switch to separate cbcmac driver")
refactored the CCM driver to allow separate implementations of the
underlying MAC to be provided by a platform. However, in doing so, it
moved some data from the linear region to the stack, which violates the
SG constraints when the stack is virtually mapped.

So move idata/odata back to the request ctx struct, of which we can
reasonably expect that it has been allocated using kmalloc() et al.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Fixes: f15f05b0 ("crypto: ccm - switch to separate cbcmac driver")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When we're used as a fallback algorithm, we should propagate
the NEED_FALLBACK bit when searching for the underlying ECB mode.

This just happens to fix a hang too because otherwise the search
may end up loading the same module that triggered this XTS creation.

Cc: stable@vger.kernel.org #4.10
Fixes: f1c131b4 ("crypto: xts - Convert to skcipher")
Reported-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch adds crypto_requires_off which is an extension of
crypto_requires_sync for similar bits such as NEED_FALLBACK.

Cc: stable@vger.kernel.org #4.10
Suggested-by: Marcelo Cerri <marcelo.cerri@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

If NO_DMA=y:

    ERROR: "bad_dma_ops" [drivers/crypto/mediatek/mtk-crypto.ko] undefined!

Add a dependency on HAS_DMA to fix this.

Fixes: 7dee9f61 ("crypto: mediatek - remove ARM dependencies")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

If NO_DMA=y:

    ERROR: "bad_dma_ops" [drivers/crypto/atmel-tdes.ko] undefined!
    ERROR: "bad_dma_ops" [drivers/crypto/atmel-sha.ko] undefined!

Add dependencies on HAS_DMA to fix this.

Fixes: ceb4afb3 ("crypto: atmel - refine Kconfig dependencies")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The exit path when curr->head cannot be allocated fails to kfree the
earlier allocated curr.  Fix this by kfree'ing it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Fix the following smatch errors
cptvf_reqmanager.c:333 do_post_process() warn: variable dereferenced
before check 'cptvf'
cptvf_main.c:825 cptvf_remove() error: we previously assumed 'cptvf'
could be null
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Since the
   commit f1c131b4
   crypto: xts - Convert to skcipher
the XTS mode is based on ECB, so the mode must select
ECB otherwise it can fail to initialize.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

pci_enable_msix has been long deprecated, but this driver adds a new
instance.  Convert it to pci_alloc_irq_vectors and greatly simplify
the code, and make sure the prope code properly unwinds.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

pci_enable_msix has been long deprecated, but this driver adds a new
instance.  Convert it to pci_alloc_irq_vectors and greatly simplify
the code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

In Broadcom SPU driver, in case where incremental hash
is done in software in ahash_finup(), tmpbuf was freed
twice.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rob Rice <rob.rice@broadcom.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The driver fails to build if MSI support is disabled:

In file included from /git/arm-soc/drivers/crypto/cavium/cpt/cptpf_main.c:18:0:
drivers/crypto/cavium/cpt/cptpf.h:57:20: error: array type has incomplete element type 'struct msix_entry'
  struct msix_entry msix_entries[CPT_PF_MSIX_VECTORS];
                    ^~~~~~~~~~~~
drivers/crypto/cavium/cpt/cptpf_main.c: In function 'cpt_enable_msix':
drivers/crypto/cavium/cpt/cptpf_main.c:344:8: error: implicit declaration of function 'pci_enable_msix';did you mean 'cpt_enable_msix'? [-Werror=implicit-function-declaration]

On the other hand, it doesn't seem to have any build dependency on ARCH_THUNDER,
so let's allow compile-testing to catch this kind of problem more easily.
The 64-bit dependency is needed for the use of readq/writeq.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

cpt_bind_vq_to_grp() could return an error code. However, it currently
returns a u8. This produce the static checker warning.

drivers/crypto/cavium/cpt/cptpf_mbox.c:70 cpt_bind_vq_to_grp() warn: signedness bug returning '(-22)'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Fix a single letter typo in api-skcipher.rst.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

omap-rng also supports Marvell Armada 7k/8k SoCs, but no mention of this
is made in the help text, despite the dependency being added. Explicitly
mention these SoCs in the help description so people know that it covers
more than just TI SoCs.

Fixes: 38321242 ("hwrng: omap - Add device variant for SafeXcel IP-76 found in Armada 8K")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The CCM driver forces 32-bit alignment even if the underlying ciphers
don't care about alignment. This is because crypto_xor() used to require
this, but since this is no longer the case, drop the hardcoded minimum
of 32 bits.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The CCM driver was recently updated to defer the MAC part of the algorithm
to a dedicated crypto transform, and a template for instantiating such
transforms was added at the same time.

However, this new cbcmac template fails to take the alignmask of the
encapsulated cipher into account, which may result in buffer addresses
being passed down that are not sufficiently aligned.

So update the code to ensure that the digest buffer in the desc ctx
appears at a sufficiently aligned offset, and tweak the code so that all
calls to crypto_cipher_encrypt_one() operate on this buffer exclusively.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

If we register the DMA API debug notification chain to
receive platform bus events:
    dma_debug_add_bus(&platform_bus_type);
we start receiving warnings after a simple test like "modprobe caam_jr &&
modprobe caamhash && modprobe -r caamhash && modprobe -r caam_jr":
platform ffe301000.jr: DMA-API: device driver has pending DMA allocations while released from device [count=1938]
One of leaked entries details: [device address=0x0000000173fda090] [size=63 bytes] [mapped with DMA_TO_DEVICE] [mapped as single]

It turns out there are several issues with handling buf_dma (mapping of buffer
holding the previous chunk smaller than hash block size):
-detection of buf_dma mapping failure occurs too late, after a job descriptor
using that value has been submitted for execution
-dma mapping leak - unmapping is not performed in all places: for e.g.
in ahash_export or in most ahash_fin* callbacks (due to current back-to-back
implementation of buf_dma unmapping/mapping)

Fix these by:
-calling dma_mapping_error() on buf_dma right after the mapping and providing
an error code if needed
-unmapping buf_dma during the "job done" (ahash_done_*) callbacks
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

caamhash uses double buffering for holding previous/current
and next chunks (data smaller than block size) to be hashed.

Add (inline) functions to abstract this mechanism.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

In case ctx_dma dma mapping fails, ahash_unmap_ctx() tries to
dma unmap an invalid address:
map_seq_out_ptr_ctx() / ctx_map_to_sec4_sg() -> goto unmap_ctx ->
-> ahash_unmap_ctx() -> dma unmap ctx_dma

There is also possible to reach ahash_unmap_ctx() with ctx_dma
uninitialzed or to try to unmap the same address twice.

Fix these by setting ctx_dma = 0 where needed:
-initialize ctx_dma in ahash_init()
-clear ctx_dma in case of mapping error (instead of holding
the error code returned by the dma map function)
-clear ctx_dma after each unmapping

Fixes: 32686d34 ("crypto: caam - ensure that we clean up after an error")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

setkey() callback may be invoked multiple times for the same tfm.
In this case, DMA API leaks are caused by shared descriptors
(and key for caamalg) being mapped several times and unmapped only once.
Fix this by performing mapping / unmapping only in crypto algorithm's
cra_init() / cra_exit() callbacks and sync_for_device in the setkey()
tfm callback.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Shared descriptors for hash algorithms are small enough
for (split) keys to be inlined in all cases.
Since driver already does this, all what's left is to remove
unused ctx->key_dma.

Fixes: 045e3678 ("crypto: caam - ahash hmac support")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

dma_map_sg() might coalesce S/G entries, so use the number of S/G
entries returned by it instead of what sg_nents_for_len() initially
returns.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Replace internal sg_count() function and the convoluted logic
around it with the standard sg_nents_for_len() function.
src_nents, dst_nents now hold the number of SW S/G entries,
instead of the HW S/G table entries.

With this change, null (zero length) input data for AEAD case
needs to be handled in a visible way. req->src is no longer
(un)mapped, pointer address is set to 0 in SEQ IN PTR command.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

sg_count() internally calls sg_nents_for_len(), which could fail
in case the required number of bytes is larger than the total
bytes in the S/G.

Thus, add checks to validate the input.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

HW S/G generation does not work properly when the following conditions
are met:
-src == dst
-src/dst is S/G
-IV is right before (contiguous with) the first src/dst S/G entry
since "iv_contig" is set to true (iv_contig is a misnomer here and
it actually refers to the whole output being contiguous)

Fix this by setting dst S/G nents equal to src S/G nents, instead of
leaving it set to init value (0).
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

If one of the JRs failed at init, the next JR used
the failed JR's IO space. The patch fixes this bug.
Signed-off-by: Tudor Ambarus <tudor-dan.ambarus@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Setting the dma mask could fail, thus make sure it succeeds
before going further.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

intern.h, jr.h are not needed in error.c
error.h is not needed in ctrl.c
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The reverse-get/set functions can be simplified by
eliminating unused code.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Move the command queue tail pointer when an error is
detected. Always return the error.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The CCP initialization messages only need to be sent to
syslog in debug mode.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch clarifies and fixes how errors should be handled by
atmel_sha_start().

For update operations, the previous code wrongly assumed that
(err != -EINPROGRESS) implies (err == 0). It's wrong because that doesn't
take the error cases (err < 0) into account.

This patch also adds many comments to detail all the possible returned
values and what should be done in each case.

Especially, when an error occurs, since atmel_sha_complete() has already
been called, hence releasing the hardware, atmel_sha_start() must not call
atmel_sha_finish_req() later otherwise atmel_sha_complete() would be
called a second time.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch fixes a previous patch: "crypto: atmel-sha - update request
queue management to make it more generic".

Indeed the patch above should have replaced the "return -EINVAL;" lines by
"return atmel_sha_complete(dd, -EINVAL);" but instead replaced them by a
simple call of "atmel_sha_complete(dd, -EINVAL);".
Hence all "return" instructions were missing.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Ensure that the size field is correctly populated for
all AES modes.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add Broadcom Secure Processing Unit (SPU) crypto driver for SPU
hardware crypto offload. The driver supports ablkcipher, ahash,
and aead symmetric crypto operations.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Signed-off-by: Rob Rice <rob.rice@broadcom.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Device tree documentation for Broadcom Secure Processing Unit
(SPU) crypto hardware.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Signed-off-by: Rob Rice <rob.rice@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add the CPT options in crypto Kconfig and update the
crypto Makefile

Update the MAINTAINERS file too.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Reviewed-by: David Daney <david.daney@cavium.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Enable the CPT VF driver. CPT is the cryptographic Acceleration Unit
in Octeon-tx series of processors.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Reviewed-by: David Daney <david.daney@cavium.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>