In xmit path, we build a flowi6 which will be used for the output route lookup.
We are sending a GRE packet, neither IPv4 nor IPv6 encapsulated packet, thus the
protocol should be IPPROTO_GRE.

Fixes: c12b395a ("gre: Support GRE over IPv6")
Reported-by: Matthieu Ternisien d'Ouville <matthieu.tdo@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Resume the device before setting the MAC address.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I've noticed every time the interface is set to 'up,', the kernel
reports that the link speed is set to 100 Mbps/Full Duplex, even
when ethtool is used to set autonegotiation to 'off', half
duplex, 10 Mbps.
It can be tested by:
 ifconfig eth0 down
 ethtool -s eth0 autoneg off speed 10 duplex half
 ifconfig eth0 up

Then checking 'dmesg' for the link speed.
Signed-off-by: Michel Stam <m.stam@fugro.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Herton R. Krzesinski says:

====================
Small fixes/changes for RDS

I got a report of one issue within RDS (after investigation it was a double
free), and I'm sending the fix (patch 3/3) which reporter said it works (no more
WARNING triggered on a specially instrumented kernel). The report/test was done
on a very old kernel (RHEL 5, 2.6.18 based with backports), but the problem the
patch handles still exists and should not change. Besides that, while
reviewing some of the code but being unable to reproduce with rds_tcp, I
noticed two small improvements/fixes which are in patches 1 and 2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

I got a report of a double free happening at RDS slab cache. One
suspicion was that may be somewhere we were doing a sock_hold/sock_put
on an already freed sock. Thus after providing a kernel with the
following change:

 static inline void sock_hold(struct sock *sk)
 {
-       atomic_inc(&sk->sk_refcnt);
+       if (!atomic_inc_not_zero(&sk->sk_refcnt))
+               WARN(1, "Trying to hold sock already gone: %p (family: %hd)\n",
+                       sk, sk->sk_family);
 }

The warning successfuly triggered:

Trying to hold sock already gone: ffff81f6dda61280 (family: 21)
WARNING: at include/net/sock.h:350 sock_hold()
Call Trace:
<IRQ>  [<ffffffff8adac135>] :rds:rds_send_remove_from_sock+0xf0/0x21b
[<ffffffff8adad35c>] :rds:rds_send_drop_acked+0xbf/0xcf
[<ffffffff8addf546>] :rds_rdma:rds_ib_recv_tasklet_fn+0x256/0x2dc
[<ffffffff8009899a>] tasklet_action+0x8f/0x12b
[<ffffffff800125a2>] __do_softirq+0x89/0x133
[<ffffffff8005f30c>] call_softirq+0x1c/0x28
[<ffffffff8006e644>] do_softirq+0x2c/0x7d
[<ffffffff8006e4d4>] do_IRQ+0xee/0xf7
[<ffffffff8005e625>] ret_from_intr+0x0/0xa
<EOI>

Looking at the call chain above, the only way I think this would be
possible is if somewhere we already released the same socket->sock which
is assigned to the rds_message at rds_send_remove_from_sock. Which seems
only possible to happen after the tear down done on rds_release.

rds_release properly calls rds_send_drop_to to drop the socket from any
rds_message, and some proper synchronization is in place to avoid race
with rds_send_drop_acked/rds_send_remove_from_sock. However, I still see
a very narrow window where it may be possible we touch a sock already
released: when rds_release races with rds_send_drop_acked, we check
RDS_MSG_ON_CONN to avoid cleanup on the same rds_message, but in this
specific case we don't clear rm->m_rs. In this case, it seems we could
then go on at rds_send_drop_to and after it returns, the sock is freed
by last sock_put on rds_release, with concurrently we being at
rds_send_remove_from_sock; then at some point in the loop at
rds_send_remove_from_sock we process an rds_message which didn't have
rm->m_rs unset for a freed sock, and a possible sock_hold on an sock
already gone at rds_release happens.

This hopefully address the described condition above and avoids a double
free on "second last" sock_put. In addition, I removed the comment about
socket destruction on top of rds_send_drop_acked: we call rds_send_drop_to
in rds_release and we should have things properly serialized there, thus
I can't see the comment being accurate there.
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I see two problems if we consider the sock->ops->connect attempt to fail in
rds_tcp_conn_connect. The first issue is that for example we don't remove the
previously added rds_tcp_connection item to rds_tcp_tc_list at
rds_tcp_set_callbacks, which means that on a next reconnect attempt for the
same rds_connection, when rds_tcp_conn_connect is called we can again call
rds_tcp_set_callbacks, resulting in duplicated items on rds_tcp_tc_list,
leading to list corruption: to avoid this just make sure we call
properly rds_tcp_restore_callbacks before we exit. The second issue
is that we should also release the sock properly, by setting sock = NULL
only if we are returning without error.
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull raid5 discard fix from Neil Brown:
 "One fix for raid5 discard issue"

* tag 'md/3.17-final-fix' of git://neil.brown.name/md:
  md/raid5: disable 'DISCARD' by default due to safety concerns.

Pull drm fixes from Dave Airlie:
 "Nothing too major or scary.

  One i915 regression fix, nouveau has a tmds regression fix, along with
  a regression fix for the runtime pm code for optimus laptops not
  restoring the display hw correctly"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/nouveau: make sure display hardware is reinitialised on runtime resume
  drm/nouveau: punt fbcon resume out to a workqueue
  drm/nouveau: fix regression on original nv50 board
  drm/nv50/disp: fix dpms regression on certain boards
  drm/i915: Flush the PTEs after updating them before suspend

Pull ACPI and power management fixes from Rafael Wysocki:
 "These are three regression fixes (cpufreq core, pcc-cpufreq, i915 /
  ACPI) and one trivial fix for a callback return value mismatch in the
  cpufreq integrator driver.

  Specifics:

   - A recent cpufreq core fix went too far and introduced a regression
     in the system suspend code path.  Fix from Viresh Kumar.

   - An ACPI-related commit in the i915 driver that fixed backlight
     problems for some Thinkpads inadvertently broke a Dell machine (in
     3.16).  Fix from Aaron Lu.

   - The pcc-cpufreq driver was broken during the 3.15 cycle by a commit
     that put wait_event() under a spinlock by mistake.  Fix that
     (Rafael J Wysocki).

   - The return value type of integrator_cpufreq_remove() is void, but
     should be int.  Fix from Arnd Bergmann"

* tag 'pm+acpi-3.17-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: update 'cpufreq_suspended' after stopping governors
  ACPI / i915: Update the condition to ignore firmware backlight change request
  cpufreq: integrator: fix integrator_cpufreq_remove return type
  cpufreq: pcc-cpufreq: Fix wait_event() under spinlock

final regression fix for 3.17.

* tag 'drm-intel-fixes-2014-10-02' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Flush the PTEs after updating them before suspend

* pm-cpufreq:
  cpufreq: update 'cpufreq_suspended' after stopping governors
  cpufreq: integrator: fix integrator_cpufreq_remove return type
  cpufreq: pcc-cpufreq: Fix wait_event() under spinlock

* acpi-video:
  ACPI / i915: Update the condition to ignore firmware backlight change request

Merge fixes from Andrew Morton:
 "5 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm: page_alloc: fix zone allocation fairness on UP
  perf: fix perf bug in fork()
  MAINTAINERS: change git URL for mpc5xxx tree
  mm: memcontrol: do not iterate uninitialized memcgs
  ocfs2/dlm: should put mle when goto kill in dlm_assert_master_handler

The zone allocation batches can easily underflow due to higher-order
allocations or spills to remote nodes.  On SMP that's fine, because
underflows are expected from concurrency and dealt with by returning 0.
But on UP, zone_page_state will just return a wrapped unsigned long,
which will get past the <= 0 check and then consider the zone eligible
until its watermarks are hit.

Commit 3a025760 ("mm: page_alloc: spill to remote nodes before
waking kswapd") already made the counter-resetting use
atomic_long_read() to accomodate underflows from remote spills, but it
didn't go all the way with it.

Make it clear that these batches are expected to go negative regardless
of concurrency, and use atomic_long_read() everywhere.

Fixes: 81c0a2bb ("mm: page_alloc: fair zone allocator policy")
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org>	[3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Oleg noticed that a cleanup by Sylvain actually uncovered a bug; by
calling perf_event_free_task() when failing sched_fork() we will not yet
have done the memset() on ->perf_event_ctxp[] and will therefore try and
'free' the inherited contexts, which are still in use by the parent
process.  This is bad..
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Sylvain 'ythier' Hitier <sylvain.hitier@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The repository for mpc5xxx has been moved, update git URL to new
location.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The cgroup iterators yield css objects that have not yet gone through
css_online(), but they are not complete memcgs at this point and so the
memcg iterators should not return them.  Commit d8ad3055 ("mm/memcg:
iteration skip memcgs not yet fully initialized") set out to implement
exactly this, but it uses CSS_ONLINE, a cgroup-internal flag that does
not meet the ordering requirements for memcg, and so the iterator may
skip over initialized groups, or return partially initialized memcgs.

The cgroup core can not reasonably provide a clear answer on whether the
object around the css has been fully initialized, as that depends on
controller-specific locking and lifetime rules.  Thus, introduce a
memcg-specific flag that is set after the memcg has been initialized in
css_online(), and read before mem_cgroup_iter() callers access the memcg
members.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org>	[3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In dlm_assert_master_handler, the mle is get in dlm_find_mle, should be
put when goto kill, otherwise, this mle will never be released.
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Reviewed-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: joyce.xue <xuejiufei@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull media fix from Mauro Carvalho Chehab:
 "One last time regression fix at em28xx.  The removal of .reset_resume
  broke suspend/resume on this driver for some devices.

  There are more fixes to be done for em28xx suspend/resume to be better
  handled, but I'm opting to let them to stay for a while at the media
  devel tree, in order to get more tests.  So, for now, let's just
  revert this patch"

* tag 'media/v3.17-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  Revert "[media] media: em28xx - remove reset_resume interface"

Pull parisc fix from Helge Deller:
 "One late but trivial patch to fix the serial console on parisc
  machines which got broken during the 3.17 release cycle"

* 'parisc-3.17-8' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Fix serial console for machines with serial port on superio chip

Merge NUMA balancing related fixlets from Mel Gorman:
 "There were a few minor changes so am resending just the two patches
  that are mostly likely to affect the bug Dave and Sasha saw and marked
  them for stable.

  I'm less confident it will address Sasha's problem because while I
  have not kept up to date, I believe he's also seeing memory corruption
  issues in next from an unknown source.  Still, it would be nice to see
  how they affect trinity testing.

  I'll send the MPOL_MF_LAZY patch separately because it's not urgent"

* emailed patches from Mel Gorman <mgorman@suse.de>:
  mm: numa: Do not mark PTEs pte_numa when splitting huge pages
  mm: migrate: Close race between migration completion and mprotect

This patch reverts 1ba6e0b5 ("mm: numa: split_huge_page: transfer the
NUMA type from the pmd to the pte"). If a huge page is being split due
a protection change and the tail will be in a PROT_NONE vma then NUMA
hinting PTEs are temporarily created in the protected VMA.

 VM_RW|VM_PROTNONE
|-----------------|
      ^
      split here

In the specific case above, it should get fixed up by change_pte_range()
but there is a window of opportunity for weirdness to happen. Similarly,
if a huge page is shrunk and split during a protection update but before
pmd_numa is cleared then a pte_numa can be left behind.

Instead of adding complexity trying to deal with the case, this patch
will not mark PTEs NUMA when splitting a huge page. NUMA hinting faults
will not be triggered which is marginal in comparison to the complexity
in dealing with the corner cases during THP split.

Cc: stable@vger.kernel.org
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

A migration entry is marked as write if pte_write was true at the time the
entry was created. The VMA protections are not double checked when migration
entries are being removed as mprotect marks write-migration-entries as
read. It means that potentially we take a spurious fault to mark PTEs write
again but it's straight-forward. However, there is a race between write
migrations being marked read and migrations finishing. This potentially
allows a PTE to be write that should have been read. Close this race by
double checking the VMA permissions using maybe_mkwrite when migration
completes.

[torvalds@linux-foundation.org: use maybe_mkwrite]
Cc: stable@vger.kernel.org
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull sound fixes from Takashi Iwai:
 "Just a few pending bits of random fixes in ASoC.  Nothing exciting,
  but would be nice to be merged in 3.17, as most of them are also for
  stable kernels"

* tag 'sound-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ASoC: ssm2602: do not hardcode type to SSM2602
  ASoC: core: fix possible ZERO_SIZE_PTR pointer dereferencing error.
  MAINTAINERS: add atmel audio alsa driver maintainer entry
  ASoC: rt286: Fix sync function
  ASoC: rt286: Correct default value
  ASoC: soc-compress: fix double unlock of fe card mutex
  ASoC: fsl_ssi: fix kernel panic in probe function

A few regression fixes, the runpm ones dating back to 3.15.  Also a fairly severe TMDS regression that effected a lot of GF8/9/GT2xx users.

* 'linux-3.17' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
  drm/nouveau: make sure display hardware is reinitialised on runtime resume
  drm/nouveau: punt fbcon resume out to a workqueue
  drm/nouveau: fix regression on original nv50 board
  drm/nv50/disp: fix dpms regression on certain boards

Pull networking fixes from David Miller:

 1) Don't halt the firmware in r8152 driver, from Hayes Wang.

 2) Handle full sized 802.1ad frames in bnx2 and tg3 drivers properly,
    from Vlad Yasevich.

 3) Don't sleep while holding tx_clean_lock in netxen driver, fix from
    Manish Chopra.

 4) Certain kinds of ipv6 routes can end up endlessly failing the route
    validation test, causing it to be re-looked up over and over again.
    This particularly kills input route caching in TCP sockets.  Fix
    from Hannes Frederic Sowa.

 5) netvsc_start_xmit() has a use-after-free access to skb->len, fix
    from K Y Srinivasan.

 6) Fix matching of inverted containers in ematch module, from Ignacy
    Gawędzki.

 7) Aggregation of GRO frames via SKB ->frag_list for linear skbs isn't
    handled properly, regression fix from Eric Dumazet.

 8) Don't test return value of ipv4_neigh_lookup(), which returns an
    error pointer, against NULL.  From WANG Cong.

 9) Fix an old regression where we mistakenly allow a double add of the
    same tunnel.  Fixes from Steffen Klassert.

10) macvtap device delete and open can run in parallel and corrupt lists
    etc., fix from Vlad Yasevich.

11) Fix build error with IPV6=m NETFILTER_XT_TARGET_TPROXY=y, from Pablo
    Neira Ayuso.

12) rhashtable_destroy() triggers lockdep splats, fix also from Pablo.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
  bna: Update Maintainer Email
  r8152: disable power cut for RTL8153
  r8152: remove clearing bp
  bnx2: Correctly receive full sized 802.1ad fragmes
  tg3: Allow for recieve of full-size 8021AD frames
  r8152: fix setting RTL8152_UNPLUG
  netxen: Fix bug in Tx completion path.
  netxen: Fix BUG "sleeping function called from invalid context"
  ipv6: remove rt6i_genid
  hyperv: Fix a bug in netvsc_start_xmit()
  net: stmmac: fix stmmac_pci_probe failed when CONFIG_HAVE_CLK is selected
  ematch: Fix matching of inverted containers.
  gro: fix aggregation for skb using frag_list
  neigh: check error pointer instead of NULL for ipv4_neigh_lookup()
  ip6_gre: Return an error when adding an existing tunnel.
  ip6_vti: Return an error when adding an existing tunnel.
  ip6_tunnel: Return an error when adding an existing tunnel.
  ip6gre: add a rtnl link alias for ip6gretap
  net/mlx4_core: Allow not to specify probe_vf in SRIOV IB mode
  r8152: fix the carrier off when autoresuming
  ...

It has come to my attention (thanks Martin) that 'discard_zeroes_data'
is only a hint.  Some devices in some cases don't do what it
says on the label.

The use of DISCARD in RAID5 depends on reads from discarded regions
being predictably zero.  If a write to a previously discarded region
performs a read-modify-write cycle it assumes that the parity block
was consistent with the data blocks.  If all were zero, this would
be the case.  If some are and some aren't this would not be the case.
This could lead to data corruption after a device failure when
data needs to be reconstructed from the parity.

As we cannot trust 'discard_zeroes_data', ignore it by default
and so disallow DISCARD on all raid4/5/6 arrays.

As many devices are trustworthy, and as there are benefits to using
DISCARD, add a module parameter to over-ride this caution and cause
DISCARD to work if discard_zeroes_data is set.

If a site want to enable DISCARD on some arrays but not on others they
should select DISCARD support at the filesystem level, and set the
raid456 module parameter.
    raid456.devices_handle_discard_safely=Y

As this is a data-safety issue, I believe this patch is suitable for
-stable.
DISCARD support for RAID456 was added in 3.7

Cc: Shaohua Li <shli@kernel.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Heinz Mauelshagen <heinzm@redhat.com>
Cc: stable@vger.kernel.org (3.7+)
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Fixes: 620125f2Signed-off-by: NeilBrown <neilb@suse.de>

Linus commit 05c63c2f modified the
runtime suspend/resume paths to skip over display-related tasks to
avoid locking issues on resume.

Unfortunately, this resulted in the display hardware being left in
a partially initialised state, preventing subsequent modesets from
completing.

This commit unifies the (many) suspend/resume paths, bringing back
display (and fbcon) handling in the runtime paths.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Preparation for some runtime pm fixes.  Currently we skip over fbcon
suspend/resume in the runtime path, which causes issues on resume if
fbcon tries to write to the framebuffer before the BAR subdev has
been resumed to restore the BAR1 VM setup.

As we might be woken up via a sysfs connector, we are unable to call
fb_set_suspend() in the resume path as it could make its way down to
a modeset and cause all sorts of locking hilarity.

To solve this, we'll just delay the fbcon resume to a workqueue.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Xorg (and any non-DRM client really) doesn't have permission to directly
touch VRAM on nv50 and up, which the fence code prior to g84 depends on.

It's less invasive to temporarily grant it premission to do so, as it
previously did, than it is to rework fencenv50 to use the VM.  That
will come later on.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Reported in fdo#82527 comment #2.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Update the maintainer email for BNA driver.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: patches about firmware

The patches fix the issues when the firmware exists.

For the multiple OS, the firmware may be loaded by the
driver of the other OS. And the Linux driver has influences
on it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The firmware would be clear when the power cut is enabled for
RTL8153.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The xxx_clear_bp() is used to halt the firmware. It only necessary
for updating the new firmware. Besides, depend on the version of
the current firmware, it may have problem to halt the firmware
directly. Finally, halt the firmware would let the firmware code
useless, and the bugs which are fixed by the firmware would occur.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver, similar to tg3, has a check that will
cause full sized 802.1ad frames to be dropped.  The
frame will be larger then the standard mtu due to the
presense of vlan header that has not been stripped.
The driver should not drop this frame and should process
it just like it does for 802.1q.

CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Dept-HSGLinuxNICDev@qlogic.com
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When receiving a vlan-tagged frame that still contains
a vlan header, the length of the packet will be greater
then MTU+ETH_HLEN since it will account of the extra
vlan header.  TG3 checks this for the case for 802.1Q,
but not for 802.1ad.  As a result, full sized 802.1ad
frames get dropped by the card.

Add a check for 802.1ad protocol when receving full
sized frames.
Suggested-by: Prashant Sreedharan <prashant@broadcom.com>
CC: Prashant Sreedharan <prashant@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull nfsd bugfix from Bruce Fields:
 "This fixes a data corruption bug introduced by the v3.16 xdr encoding
  rewrite.  I haven't managed to reproduce it myself yet, but it's
  apparently not hard to hit given the right workload"

* 'for-3.17' of git://linux-nfs.org/~bfields/linux:
  nfsd4: fix corruption of NFSv4 read data

Fix the serial console on machines where the serial port is located on
the SuperIO chip.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Peter Hurley <peter@hurleysoftware.com>

Merge tag 'asoc-v3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fix SSM2602 device identification

Another fix for v3.17, fixing device identification after the split out
of the I2C and SPI code.