- 25 Nov, 2018 4 commits
-
-
Colin Ian King authored
Currently dev is dereferenced by the call dev_net(dev) before dev is null checked. Fix this by null checking dev before the potential null pointer dereference. Detected by CoverityScan, CID#1462955 ("Dereference before null check") Fixes: 23790ef1 ("net: qualcomm: rmnet: Allow to configure flags for existing devices") Signed-off-by:Colin Ian King <colin.king@canonical.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
YueHaibing authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:5883:6: warning: variable 'multitrc' set but not used [-Wunused-but-set-variable] drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:8585:32: warning: variable 'speed' set but not used [-Wunused-but-set-variable] 'multitrc' never used since introduction in commit 8e3d04fd ("cxgb4: Add MPS tracing support") 'speed' never used since introduction in commit c3168cab ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Alexey Dobriyan authored
Return code should be formally "netdev_tx_t". Signed-off-by:
Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by:
-
-
- 24 Nov, 2018 36 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linuxLinus Torvalds authored
Pull arm64 fixes from Catalin Marinas:: - Fix wrong conflict resolution around CONFIG_ARM64_SSBD - Fix sparse warning on unsigned long constant * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64: cpufeature: Fix mismerge of CONFIG_ARM64_SSBD block arm64: sysreg: fix sparse warnings
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Need to take mutex in ath9k_add_interface(), from Dan Carpenter. 2) Fix mt76 build without CONFIG_LEDS_CLASS, from Arnd Bergmann. 3) Fix socket wmem accounting in SCTP, from Xin Long. 4) Fix failed resume crash in ena driver, from Arthur Kiyanovski. 5) qed driver passes bytes instead of bits into second arg of bitmap_weight(). From Denis Bolotin. 6) Fix reset deadlock in ibmvnic, from Juliet Kim. 7) skb_scrube_packet() needs to scrub the fwd marks too, from Petr Machata. 8) Make sure older TCP stacks see enough dup ACKs, and avoid doing SACK compression during this period, from Eric Dumazet. 9) Add atomicity to SMC protocol cursor handling, from Ursula Braun. 10) Don't leave dangling error pointer if bpf_prog_add() fails in thunderx driver, from Lorenzo Bianconi. Also, when we unmap TSO headers, set sq->tso_hdrs to NULL. 11) Fix race condition over state variables in act_police, from Davide Caratti. 12) Disable guest csum in the presence of XDP in virtio_net, from Jason Wang. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (64 commits) net: gemini: Fix copy/paste error net: phy: mscc: fix deadlock in vsc85xx_default_config dt-bindings: dsa: Fix typo in "probed" net: thunderx: set tso_hdrs pointer to NULL in nicvf_free_snd_queue net: amd: add missing of_node_put() team: no need to do team_notify_peers or team_mcast_rejoin when disabling port virtio-net: fail XDP set if guest csum is negotiated virtio-net: disable guest csum during XDP set net/sched: act_police: add missing spinlock initialization net: don't keep lonely packets forever in the gro hash net/ipv6: re-do dad when interface has IFF_NOARP flag change packet: copy user buffers before orphan or clone ibmvnic: Update driver queues after change in ring size support ibmvnic: Fix RX queue buffer cleanup net: thunderx: set xdp_prog to NULL if bpf_prog_add fails net/dim: Update DIM start sample after each DIM iteration net: faraday: ftmac100: remove netif_running(netdev) check before disabling interrupts net/smc: use after free fix in smc_wr_tx_put_slot() net/smc: atomic SMCD cursor handling net/smc: add SMC-D shutdown signal ... -
git://git.kernel.org/pub/scm/fs/xfs/xfs-linuxLinus Torvalds authored
Pull xfs fixes from Darrick Wong: "Dave and I have continued our work fixing corruption problems that can be found when running long-term burn-in exercisers on xfs. Here are some patches fixing most of the problems, but there will likely be more. :/ - Numerous corruption fixes for copy on write - Numerous corruption fixes for blocksize < pagesize writes - Don't miscalculate AG reservations for small final AGs - Fix page cache truncation to work properly for reflink and extent shifting - Fix use-after-free when retrying failed inode/dquot buffer logging - Fix corruptions seen when using copy_file_range in directio mode" * tag 'xfs-4.20-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: iomap: readpages doesn't zero page tail beyond EOF vfs: vfs_dedupe_file_range() doesn't return EOPNOTSUPP iomap: dio data corruption and spurious errors when pipes fill iomap: sub-block dio needs to zeroout beyond EOF iomap: FUA is wrong for DIO O_DSYNC writes into unwritten extents xfs: delalloc -> unwritten COW fork allocation can go wrong xfs: flush removing page cache in xfs_reflink_remap_prep xfs: extent shifting doesn't fully invalidate page cache xfs: finobt AG reserves don't consider last AG can be a runt xfs: fix transient reference count error in xfs_buf_resubmit_failed_buffers xfs: uncached buffer tracing needs to print bno xfs: make xfs_file_remap_range() static xfs: fix shared extent data corruption due to missing cow reservation -
Andreas Fiedler authored
The TX stats should be started with the tx_stats_syncp, there seems to be a copy/paste error in the driver. Signed-off-by:
Andreas Fiedler <andreas.fiedler@gmx.net> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Quentin Schulz authored
The vsc85xx_default_config function called in the vsc85xx_config_init function which is used by VSC8530, VSC8531, VSC8540 and VSC8541 PHYs mistakenly calls phy_read and phy_write in-between phy_select_page and phy_restore_page. phy_select_page and phy_restore_page actually take and release the MDIO bus lock and phy_write and phy_read take and release the lock to write or read to a PHY register. Let's fix this deadlock by using phy_modify_paged which handles correctly a read followed by a write in a non-standard page. Fixes: 6a0bfbbe ("net: phy: mscc: migrate to phy_select/restore_page functions") Signed-off-by:
Quentin Schulz <quentin.schulz@bootlin.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Fabio Estevam authored
The correct form is "can be probed", so fix the typo. Signed-off-by:
Fabio Estevam <festevam@gmail.com> Reviewed-by:
-
Lorenzo Bianconi authored
Reset snd_queue tso_hdrs pointer to NULL in nicvf_free_snd_queue routine since it is used to check if tso dma descriptor queue has been previously allocated. The issue can be triggered with the following reproducer: $ip link set dev enP2p1s0v0 xdpdrv obj xdp_dummy.o $ip link set dev enP2p1s0v0 xdpdrv off [ 341.467649] WARNING: CPU: 74 PID: 2158 at mm/vmalloc.c:1511 __vunmap+0x98/0xe0 [ 341.515010] Hardware name: GIGABYTE H270-T70/MT70-HD0, BIOS T49 02/02/2018 [ 341.521874] pstate: 60400005 (nZCv daif +PAN -UAO) [ 341.526654] pc : __vunmap+0x98/0xe0 [ 341.530132] lr : __vunmap+0x98/0xe0 [ 341.533609] sp : ffff00001c5db860 [ 341.536913] x29: ffff00001c5db860 x28: 0000000000020000 [ 341.542214] x27: ffff810feb5090b0 x26: ffff000017e57000 [ 341.547515] x25: 0000000000000000 x24: 00000000fbd00000 [ 341.552816] x23: 0000000000000000 x22: ffff810feb5090b0 [ 341.558117] x21: 0000000000000000 x20: 0000000000000000 [ 341.563418] x19: ffff000017e57000 x18: 0000000000000000 [ 341.568719] x17: 0000000000000000 x16: 0000000000000000 [ 341.574020] x15: 0000000000000010 x14: ffffffffffffffff [ 341.579321] x13: ffff00008985eb27 x12: ffff00000985eb2f [ 341.584622] x11: ffff0000096b3000 x10: ffff00001c5db510 [ 341.589923] x9 : 00000000ffffffd0 x8 : ffff0000086868e8 [ 341.595224] x7 : 3430303030303030 x6 : 00000000000006ef [ 341.600525] x5 : 00000000003fffff x4 : 0000000000000000 [ 341.605825] x3 : 0000000000000000 x2 : ffffffffffffffff [ 341.611126] x1 : ffff0000096b3728 x0 : 0000000000000038 [ 341.616428] Call trace: [ 341.618866] __vunmap+0x98/0xe0 [ 341.621997] vunmap+0x3c/0x50 [ 341.624961] arch_dma_free+0x68/0xa0 [ 341.628534] dma_direct_free+0x50/0x80 [ 341.632285] nicvf_free_resources+0x160/0x2d8 [nicvf] [ 341.637327] nicvf_config_data_transfer+0x174/0x5e8 [nicvf] [ 341.642890] nicvf_stop+0x298/0x340 [nicvf] [ 341.647066] __dev_close_many+0x9c/0x108 [ 341.650977] dev_close_many+0xa4/0x158 [ 341.654720] rollback_registered_many+0x140/0x530 [ 341.659414] rollback_registered+0x54/0x80 [ 341.663499] unregister_netdevice_queue+0x9c/0xe8 [ 341.668192] unregister_netdev+0x28/0x38 [ 341.672106] nicvf_remove+0xa4/0xa8 [nicvf] [ 341.676280] nicvf_shutdown+0x20/0x30 [nicvf] [ 341.680630] pci_device_shutdown+0x44/0x88 [ 341.684720] device_shutdown+0x144/0x250 [ 341.688640] kernel_restart_prepare+0x44/0x50 [ 341.692986] kernel_restart+0x20/0x68 [ 341.696638] __se_sys_reboot+0x210/0x238 [ 341.700550] __arm64_sys_reboot+0x24/0x30 [ 341.704555] el0_svc_handler+0x94/0x110 [ 341.708382] el0_svc+0x8/0xc [ 341.711252] ---[ end trace 3f4019c8439959c9 ]--- [ 341.715874] page:ffff7e0003ef4000 count:0 mapcount:0 mapping:0000000000000000 index:0x4 [ 341.723872] flags: 0x1fffe000000000() [ 341.727527] raw: 001fffe000000000 ffff7e0003f1a008 ffff7e0003ef4048 0000000000000000 [ 341.735263] raw: 0000000000000004 0000000000000000 00000000ffffffff 0000000000000000 [ 341.742994] page dumped because: VM_BUG_ON_PAGE(page_ref_count(page) == 0) where xdp_dummy.c is a simple bpf program that forwards the incoming frames to the network stack (available here: https://github.com/altoor/xdp_walkthrough_examples/blob/master/sample_1/xdp_dummy.c) Fixes: 05c773f5 ("net: thunderx: Add basic XDP support") Fixes: 4863dea3 ("net: Adding support for Cavium ThunderX network controller") Signed-off-by:
Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by:
-
YueHaibing authored
Fix smatch warning: drivers/ptp/ptp_clock.c:298 ptp_clock_register() warn: passing zero to 'ERR_PTR' 'err' should be set while device_create_with_groups and pps_register_source fails Fixes: 85a66e55 ("ptp: create "pins" together with the rest of attributes") Signed-off-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
David S. Miller authored
Petr Machata says: ==================== switchdev: Convert switchdev_port_obj_{add,del}() to notifiers An offloading driver may need to have access to switchdev events on ports that aren't directly under its control. An example is a VXLAN port attached to a bridge offloaded by a driver. The driver needs to know about VLANs configured on the VXLAN device. However the VXLAN device isn't stashed between the bridge and a front-panel-port device (such as is the case e.g. for LAG devices), so the usual switchdev ops don't reach the driver. VXLAN is likely not the only device type like this: in theory any L2 tunnel device that needs offloading will prompt requirement of this sort. A way to fix this is to give up the notion of port object addition / deletion as a switchdev operation, which assumes somewhat tight coupling between the message producer and consumer. And instead send the message over a notifier chain. The series starts with a clean-up patch #1, where SWITCHDEV_OBJ_PORT_{VLAN, MDB}() are fixed up to lift the constraint that the passed-in argument be a simple variable named "obj". switchdev_port_obj_add and _del are invoked in a context that permits blocking. Not only that, at least for the VLAN notification, being able to signal failure is actually important. Therefore introduce a new blocking notifier chain that the new events will be sent on. That's done in patch #2. Retain the current (atomic) notifier chain for the preexisting notifications. In patch #3, introduce two new switchdev notifier types, SWITCHDEV_PORT_OBJ_ADD and SWITCHDEV_PORT_OBJ_DEL. These notifier types communicate the same event as the corresponding switchdev op, except in a form of a notification. struct switchdev_notifier_port_obj_info was added to carry the fields that correspond to the switchdev op arguments. An additional field, handled, will be used to communicate back to switchdev that the event has reached an interested party, which will be important for the two-phase commit. In patches #4, #5, and #7, rocker, DSA resp. ethsw are updated to subscribe to the switchdev blocking notifier chain, and handle the new notifier types. #6 introduces a helper to determine whether a netdevice corresponds to a front panel port. What these three drivers have in common is that their ports don't support any uppers besides bridge. That makes it possible to ignore any notifiers that don't reference a front-panel port device, because they are certainly out of scope. Unlike the previous three, mlxsw and ocelot drivers admit stacked devices as uppers. While the current switchdev code recursively descends through layers of lower devices, eventually calling the op on a front-panel port device, the notifier would reference a stacking device that's one of front-panel ports uppers. The filtering is thus more complex. For ocelot, such iteration is currently pretty much required, because there's no bookkeeping of LAG devices. mlxsw does keep the list of LAGs, however it iterates the lower devices anyway when deciding whether an event on a tunnel device pertains to the driver or not. Therefore this patch set instead introduces, in patch #8, a helper to iterate through lowers, much like the current switchdev code does, looking for devices that match a given predicate. Then in patches #9 and #10, first mlxsw and then ocelot are updated to dispatch the newly-added notifier types to the preexisting port_obj_add/_del handlers. The dispatch is done via the new helper, to recursively descend through lower devices. Finally in patch #11, the actual switch is made, retiring the current SDO-based code in favor of a notifier. Now that the event is distributed through a notifier, the explicit netdevice check in rocker, DSA and ethsw doesn't let through any events except those done on a front-panel port itself. It is therefore unnecessary to check in VLAN-handling code whether a VLAN was added to the bridge itself: such events will simply be ignored much sooner. Therefore remove it in patch #12. ==================== Signed-off-by: -
Petr Machata authored
Due to an explicit check in rocker_world_port_obj_vlan_add(), dsa_slave_switchdev_event() resp. port_switchdev_event(), VLAN objects that are added to a device that is not a front-panel port device are ignored. Therefore this check is immaterial. Signed-off-by:
Petr Machata <petrm@mellanox.com> Acked-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Petr Machata authored
Drop switchdev_ops.switchdev_port_obj_add and _del. Drop the uses of this field from all clients, which were migrated to use switchdev notification in the previous patches. Add a new function switchdev_port_obj_notify() that sends the switchdev notifications SWITCHDEV_PORT_OBJ_ADD and _DEL. Update switchdev_port_obj_del_now() to dispatch to this new function. Drop __switchdev_port_obj_add() and update switchdev_port_obj_add() likewise. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Petr Machata authored
Following patches will change the way of distributing port object changes from a switchdev operation to a switchdev notifier. The switchdev code currently recursively descends through layers of lower devices, eventually calling the op on a front-panel port device. The notifier will instead be sent referencing the bridge port device, which may be a stacking device that's one of front-panel ports uppers, or a completely unrelated device. Dispatch the new events to ocelot_port_obj_add() resp. _del() to maintain the same behavior that the switchdev operation based code currently has. Pass through switchdev_handle_port_obj_add() / _del() to handle the recursive descend, because Ocelot supports LAG uppers. Register to the new switchdev blocking notifier chain to get the new events when they start getting distributed. Signed-off-by:
-
Petr Machata authored
Following patches will change the way of distributing port object changes from a switchdev operation to a switchdev notifier. The switchdev code currently recursively descends through layers of lower devices, eventually calling the op on a front-panel port device. The notifier will instead be sent referencing the bridge port device, which may be a stacking device that's one of front-panel ports uppers, or a completely unrelated device. To handle SWITCHDEV_PORT_OBJ_ADD and _DEL, subscribe to the blocking notifier chain. Dispatch to mlxsw_sp_port_obj_add() resp. _del() to maintain the behavior that the switchdev operation based code currently has. Defer to switchdev_handle_port_obj_add() / _del() to handle the recursive descend, because mlxsw supports a number of upper types. Signed-off-by:
-
Petr Machata authored
After the transition from switchdev operations to notifier chain (which will take place in following patches), the onus is on the driver to find its own devices below possible layer of LAG or other uppers. The logic to do so is fairly repetitive: each driver is looking for its own devices among the lowers of the notified device. For those that it finds, it calls a handler. To indicate that the event was handled, struct switchdev_notifier_port_obj_info.handled is set. The differences lie only in what constitutes an "own" device and what handler to call. Therefore abstract this logic into two helpers, switchdev_handle_port_obj_add() and switchdev_handle_port_obj_del(). If a driver only supports physical ports under a bridge device, it will simply avoid this layer of indirection. One area where this helper diverges from the current switchdev behavior is the case of mixed lowers, some of which are switchdev ports and some of which are not. Previously, such scenario would fail with -EOPNOTSUPP. The helper could do that for lowers for which the passed-in predicate doesn't hold. That would however break the case that switchdev ports from several different drivers are stashed under one master, a scenario that switchdev currently happily supports. Therefore tolerate any and all unknown netdevices, whether they are backed by a switchdev driver or not. Signed-off-by:
-
Petr Machata authored
Following patches will change the way of distributing port object changes from a switchdev operation to a switchdev notifier. The switchdev code currently recursively descends through layers of lower devices, eventually calling the op on a front-panel port device. The notifier will instead be sent referencing the bridge port device, which may be a stacking device that's one of front-panel ports uppers, or a completely unrelated device. ethsw currently doesn't support any uppers other than bridge. SWITCHDEV_OBJ_ID_HOST_MDB and _PORT_MDB objects are always notified on the bridge port device. Thus the only case that a stacked device could be validly referenced by port object notifications are bridge notifications for VLAN objects added to the bridge itself. But the driver explicitly rejects such notifications in port_vlans_add(). It is therefore safe to assume that the only interesting case is that the notification is on a front-panel port netdevice. To handle SWITCHDEV_PORT_OBJ_ADD and _DEL, subscribe to the blocking notifier chain. Dispatch to swdev_port_obj_add() resp. _del() to maintain the behavior that the switchdev operation based code currently has. Signed-off-by:
-
Petr Machata authored
ethsw currently uses an open-coded comparison of netdev_ops to determine whether whether a device represents a front panel port. Wrap this into a named function to simplify reuse. Signed-off-by:
-
Petr Machata authored
Following patches will change the way of distributing port object changes from a switchdev operation to a switchdev notifier. The switchdev code currently recursively descends through layers of lower devices, eventually calling the op on a front-panel port device. The notifier will instead be sent referencing the bridge port device, which may be a stacking device that's one of front-panel ports uppers, or a completely unrelated device. DSA currently doesn't support any other uppers than bridge. SWITCHDEV_OBJ_ID_HOST_MDB and _PORT_MDB objects are always notified on the bridge port device. Thus the only case that a stacked device could be validly referenced by port object notifications are bridge notifications for VLAN objects added to the bridge itself. But the driver explicitly rejects such notifications in dsa_port_vlan_add(). It is therefore safe to assume that the only interesting case is that the notification is on a front-panel port netdevice. Therefore keep the filtering by dsa_slave_dev_check() in place. To handle SWITCHDEV_PORT_OBJ_ADD and _DEL, subscribe to the blocking notifier chain. Dispatch to rocker_port_obj_add() resp. _del() to maintain the behavior that the switchdev operation based code currently has. Signed-off-by:
-
Petr Machata authored
Following patches will change the way of distributing port object changes from a switchdev operation to a switchdev notifier. The switchdev code currently recursively descends through layers of lower devices, eventually calling the op on a front-panel port device. The notifier will instead be sent referencing the bridge port device, which may be a stacking device that's one of front-panel ports uppers, or a completely unrelated device. rocker currently doesn't support any uppers other than bridge. Thus the only case that a stacked device could be validly referenced by port object notifications are bridge notifications for VLAN objects added to the bridge itself. But the driver explicitly rejects such notifications in rocker_world_port_obj_vlan_add(). It is therefore safe to assume that the only interesting case is that the notification is on a front-panel port netdevice. Subscribe to the blocking notifier chain. In the handler, filter out notifications on any foreign netdevices. Dispatch the new notifiers to rocker_port_obj_add() resp. _del() to maintain the behavior that the switchdev operation based code currently has. Signed-off-by:
-
Petr Machata authored
An offloading driver may need to have access to switchdev events on ports that aren't directly under its control. An example is a VXLAN port attached to a bridge offloaded by a driver. The driver needs to know about VLANs configured on the VXLAN device. However the VXLAN device isn't stashed between the bridge and a front-panel-port device (such as is the case e.g. for LAG devices), so the usual switchdev ops don't reach the driver. VXLAN is likely not the only device type like this: in theory any L2 tunnel device that needs offloading will prompt requirement of this sort. This falsifies the assumption that only the lower devices of a front panel port need to be notified to achieve flawless offloading. A way to fix this is to give up the notion of port object addition / deletion as a switchdev operation, which assumes somewhat tight coupling between the message producer and consumer. And instead send the message over a notifier chain. To that end, introduce two new switchdev notifier types, SWITCHDEV_PORT_OBJ_ADD and SWITCHDEV_PORT_OBJ_DEL. These notifier types communicate the same event as the corresponding switchdev op, except in a form of a notification. struct switchdev_notifier_port_obj_info was added to carry the fields that the switchdev op carries. An additional field, handled, will be used to communicate back to switchdev that the event has reached an interested party, which will be important for the two-phase commit. The two switchdev operations themselves are kept in place. Following patches first convert individual clients to the notifier protocol, and only then are the operations removed. Signed-off-by:
-
Petr Machata authored
In general one can't assume that a switchdev notifier is called in a non-atomic context, and correspondingly, the switchdev notifier chain is an atomic one. However, port object addition and deletion messages are delivered from a process context. Even the MDB addition messages, whose delivery is scheduled from atomic context, are queued and the delivery itself takes place in blocking context. For VLAN messages in particular, keeping the blocking nature is important for error reporting. Therefore introduce a blocking notifier chain and related service functions to distribute the notifications for which a blocking context can be assumed. Signed-off-by:
-
Petr Machata authored
The two macros SWITCHDEV_OBJ_PORT_VLAN() and SWITCHDEV_OBJ_PORT_MDB() expand to a container_of() call, yielding an appropriate container of their sole argument. However, due to a name collision, the first argument, i.e. the contained object pointer, is not the only one to get expanded. The third argument, which is a structure member name, and should be kept literal, gets expanded as well. The only safe way to use these two macros is therefore to name the local variable passed to them "obj". To fix this, rename the sole argument of the two macros from "obj" (which collides with the member name) to "OBJ". Additionally, instead of passing "OBJ" to container_of() verbatim, parenthesize it, so that a comma in the passed-in expression doesn't pollute the container_of() invocation. Signed-off-by:
-
David S. Miller authored
Heiner Kallweit says: ==================== r8169: some functional improvements This series includes a few functional improvements. ==================== Signed-off-by: -
Heiner Kallweit authored
Replace macro TX_FRAGS_READY_FOR with function rtl_tx_slots_avail to make code cleaner and type-safe. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Heiner Kallweit authored
Use napi_consume_skb() where possible to profit from bulk free infrastructure. Signed-off-by:
-
Heiner Kallweit authored
For the GMII chip versions we set the version number which was set already. This can be simplified. Signed-off-by:
-
Heiner Kallweit authored
Even the chip versions within a family have so many differences that using a default chip version doesn't really make sense. Instead of leaving a best case flaky network connectivity, bail out and report the unknown chip version. Signed-off-by:
-
Heiner Kallweit authored
Remove ancient GCC bug workaround in a second place and factor out rtl_8169_get_txd_opts1. Signed-off-by:
-
David S. Miller authored
Salil Mehta says: ==================== net: hns3: Adds support of debugfs to HNS3 driver This patchset adds support of debugfs to the HNS3 driver. Support has been added to query info related to below items: 1. Queue related ("echo queue info [queue no] > cmd") 2. Flow Director ("echo dump fd tcam > cmd") 3. TC config ("echo dump tc > cmd") 4. Transmit Module/Scheduler ("echo dump tm > cmd") 5. QoS pause ("echo dump qos pause cfg > cmd") 6. QoS buffer ("echo dump qos pri map > cmd") 7. QoS prio map ("echo dump qos buf cfg > cmd") NOTE: Above commands are *read-only* and are only intended to query the information from the SoC(and dump inside the kernel, for now) and in no way tries to perform write operations for the purpose of configuration etc. Change Log ---------- V1-->V2: * Addressed the comments provided by Jakub Kicinski. 1. Removed the .rej files mistakenly made part of Flow Director patch. Link: https://lkml.org/lkml/2018/11/20/249 2. Added command summary in the cover letter Link: https://lkml.org/lkml/2018/11/22/1 ==================== Signed-off-by: -
liuzhongzhu authored
This patch prints qos buffer config information. debugfs command: echo dump qos buf cfg > cmd Sample Command: root@(none)# echo dump qos buf cfg > cmd hns3 0000:7d:00.0: dump qos buf cfg hns3 0000:7d:00.0: tx_packet_buf_tc_0: 0x1aa hns3 0000:7d:00.0: tx_packet_buf_tc_1: 0x0 hns3 0000:7d:00.0: tx_packet_buf_tc_2: 0x0 hns3 0000:7d:00.0: tx_packet_buf_tc_3: 0x0 hns3 0000:7d:00.0: tx_packet_buf_tc_4: 0x0 hns3 0000:7d:00.0: tx_packet_buf_tc_5: 0x0 hns3 0000:7d:00.0: tx_packet_buf_tc_6: 0x0 hns3 0000:7d:00.0: tx_packet_buf_tc_7: 0x0 hns3 0000:7d:00.0: hns3 0000:7d:00.0: rx_packet_buf_tc_0: 0x130 hns3 0000:7d:00.0: rx_packet_buf_tc_1: 0x0 hns3 0000:7d:00.0: rx_packet_buf_tc_2: 0x0 hns3 0000:7d:00.0: rx_packet_buf_tc_3: 0x0 hns3 0000:7d:00.0: rx_packet_buf_tc_4: 0x0 hns3 0000:7d:00.0: rx_packet_buf_tc_5: 0x0 hns3 0000:7d:00.0: rx_packet_buf_tc_6: 0x0 hns3 0000:7d:00.0: rx_packet_buf_tc_7: 0x0 hns3 0000:7d:00.0: rx_share_buf: 0x1e0e root@(none)# Signed-off-by:
liuzhongzhu <liuzhongzhu@huawei.com> Signed-off-by:
Salil Mehta <salil.mehta@huawei.com> Signed-off-by:
-
liuzhongzhu authored
This patch prints qos priority map information. debugfs command: echo dump qos pri map > cmd Sample Command: root@(none)# echo dump qos pri map > cmd hns3 0000:7d:00.0: dump qos pri map hns3 0000:7d:00.0: vlan_to_pri: 0x0 hns3 0000:7d:00.0: pri_0_to_tc: 0x0 hns3 0000:7d:00.0: pri_1_to_tc: 0x0 hns3 0000:7d:00.0: pri_2_to_tc: 0x0 hns3 0000:7d:00.0: pri_3_to_tc: 0x0 hns3 0000:7d:00.0: pri_4_to_tc: 0x0 hns3 0000:7d:00.0: pri_5_to_tc: 0x0 hns3 0000:7d:00.0: pri_6_to_tc: 0x0 hns3 0000:7d:00.0: pri_7_to_tc: 0x0 root@(none)# Signed-off-by:
-
liuzhongzhu authored
This patch prints qos pause config information. debugfs command: echo dump qos pause cfg > cmd Sample Command: root@(none)# echo dump qos pause cfg > cmd hns3 0000:7d:00.0: dump qos pause cfg hns3 0000:7d:00.0: pause_trans_gap: 0xff hns3 0000:7d:00.0: pause_trans_time: 0xffff root@(none)# Signed-off-by:
-
liuzhongzhu authored
This patch prints Transmit Module's Traffic sched related config information. debugfs command: echo dump tm > cmd Sample output: root@(none)# echo dump tm > cmd hns3 0000:7d:00.0: dump tm hns3 0000:7d:00.0: PG_TO_PRI gp_id: 0 hns3 0000:7d:00.0: PG_TO_PRI map: 0x1 hns3 0000:7d:00.0: QS_TO_PRI qs_id: 0 hns3 0000:7d:00.0: QS_TO_PRI priority: 0 hns3 0000:7d:00.0: QS_TO_PRI link_vld: 1 hns3 0000:7d:00.0: NQ_TO_QS nq_id: 0 hns3 0000:7d:00.0: NQ_TO_QS qset_id: 1024 hns3 0000:7d:00.0: PG pg_id: 0 hns3 0000:7d:00.0: PG dwrr: 100 hns3 0000:7d:00.0: QS qs_id: 0 hns3 0000:7d:00.0: QS dwrr: 100 hns3 0000:7d:00.0: PRI pri_id: 0 hns3 0000:7d:00.0: PRI dwrr: 100 hns3 0000:7d:00.0: PRI_C pri_id: 0 hns3 0000:7d:00.0: PRI_C pri_shapping: 0x2850000 hns3 0000:7d:00.0: PRI_P pri_id: 0 hns3 0000:7d:00.0: PRI_P pri_shapping: 0x2850796 hns3 0000:7d:00.0: PG_C pg_id: 0 hns3 0000:7d:00.0: PG_C pg_shapping: 0x2850000 hns3 0000:7d:00.0: PG_P pg_id: 0 hns3 0000:7d:00.0: PG_P pg_shapping: 0x2850496 hns3 0000:7d:00.0: PORT port_shapping: 0x2850296 hns3 0000:7d:00.0: PG_SCH pg_id: 0 hns3 0000:7d:00.0: PRI_SCH pg_id: 0 hns3 0000:7d:00.0: QS_SCH pg_id: 0 hns3 0000:7d:00.0: BP_TO_QSET pg_id: 0 hns3 0000:7d:00.0: BP_TO_QSET pg_shapping: 0x0 hns3 0000:7d:00.0: BP_TO_QSET qs_bit_map: 0x0 root@(none)# Signed-off-by:
-
liuzhongzhu authored
This patch prints tc config information. debugfs command: echo dump tc > cmd Sample Output: root@(none)# echo dump tc > cmd hns3 0000:7d:00.0: weight_offset: 14 hns3 0000:7d:00.0: tc(0): no sp mode hns3 0000:7d:00.0: tc(1): no sp mode hns3 0000:7d:00.0: tc(2): no sp mode hns3 0000:7d:00.0: tc(3): no sp mode hns3 0000:7d:00.0: tc(4): no sp mode hns3 0000:7d:00.0: tc(5): no sp mode hns3 0000:7d:00.0: tc(6): no sp mode hns3 0000:7d:00.0: tc(7): no sp mode root@(none)# Signed-off-by:
-
liuzhongzhu authored
All the Flow Director rules are stored in tcam blocks. For each bit of tcam entry, the match value depends on two input value(x, y). debugfs command: echo dump fd tcam > cmd Sample output: root@(none)# echo dump fd tcam > cmd hns3 0000:7d:00.0: read result tcam key x(31): hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 08000000 hns3 0000:7d:00.0: 00000600 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: read result tcam key y(31): hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: f7ff0000 hns3 0000:7d:00.0: 0000f900 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 00000000 hns3 0000:7d:00.0: 0000fff8 root@(none)# Signed-off-by:
-
liuzhongzhu authored
Query the queue information of the current NIC such as BD size, queue header and tail pointer. This patch adds support for debugfs command: echo queue info 1 > cmd it can print queue config information... root@(none)# echo queue info 1 > cmd hns3 0000:7d:00.0: queue info hns3 0000:7d:00.0: RX(1) BASE ADD: 0x00000000ffb58000 hns3 0000:7d:00.0: RX(1) RING BD NUM: 127 hns3 0000:7d:00.0: RX(1) RING BD LEN: 2 hns3 0000:7d:00.0: RX(1) RING TAIL: 120 hns3 0000:7d:00.0: RX(1) RING HEAD: 0 hns3 0000:7d:00.0: RX(1) RING FBDNUM: 0 hns3 0000:7d:00.0: RX(1) RING PKTNUM: 0 hns3 0000:7d:00.0: TX(1) BASE ADD: 0x00000000fffd8000 hns3 0000:7d:00.0: TX(1) RING BD NUM: 127 hns3 0000:7d:00.0: TX(1) RING TC: 0 hns3 0000:7d:00.0: TX(1) RING TAIL: 2 hns3 0000:7d:00.0: TX(1) RING HEAD: 2 hns3 0000:7d:00.0: TX(1) RING FBDNUM: 0 hns3 0000:7d:00.0: TX(1) RING OFFSET: 0 hns3 0000:7d:00.0: TX(1) RING PKTNUM: 0 root@(none)# Signed-off-by:
-
liuzhongzhu authored
Add the debugfs framework to the driver and create a debugfs command interface for each device. example command: "echo queue info > cmd" Query the packet forwarding queue information. Signed-off-by:
-
