Some newer target uses "Status Qualifier" response in a returned "Busy
Status". This new response code of 0x4001, which is "Scope" bits,
translates to "Affects all units accessible by target".  Due to this new
value returned in the Scope bits, driver was using that value as timeout
value which resulted into driver waiting for 27min timeout.

This patch masks off this Scope bits so that driver does not use this
value as retry delay time.

Cc: <stable@vger.kernel.org>
Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This patch fixes a crash on qla2x00_mailbox_command caused when the driver
is on UNLOADING state and tries to call qla2x00_poll, which triggers a
NULL pointer dereference.
Signed-off-by: Rodrigo R. Galvao <rosattig@linux.vnet.ibm.com>
Signed-off-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

If AHD_DEBUG is enabled and ahd_platform_alloc fails then ahd is set to
null and the debug printk dereferences ahd when passing it to ahd_name.
Fix this by moving the debug printk to before the call to
ahd_platform_alloc where ahd is not null at that point.

Detected by CoverityScan, CID#100296 ("Explicit null dereference")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

A barrier should be added to ensure proper ordering of memory mapped
writes.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This patch prevents driver from setting lower default speed of 1 GB/sec,
if the switch does not support Get Port Speed Capabilities (GPSC)
command. Setting this default speed results into much lower write
performance for large sequential WRITE.  This patch modifies driver to
check for gpsc_supported flags and prevents driver from issuing
MBC_SET_PORT_PARAM (001Ah) to set default speed of 1 GB/sec. If driver
does not send this mailbox command, firmware assumes maximum supported
link speed and will operate at the max speed.

Cc: stable@vger.kernel.org
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reported-by: Eda Zhou <ezhou@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Tested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

'Commit cc27b735 ("PCI/portdrv: Turn off PCIe services during
shutdown")' has been added to kernel to shutdown pending PCIe port service
interrupts during reboot so that a newly started kexec kernel wouldn't
observe pending interrupts.

pcie_port_device_remove() is disabling the root port and switches by
calling pci_disable_device() after all PCIe service drivers are shutdown.

This has been found to cause crashes on HP DL360 Gen9 machines during
reboot due to hpsa driver not clearing the bus master bit during the
shutdown procedure by calling pci_disable_device().

Disable device as part of the shutdown sequence.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199779
Fixes: cc27b735 ("PCI/portdrv: Turn off PCIe services during shutdown")
Cc: stable@vger.kernel.org
Reported-by: Ryan Finnie <ryan@finnie.org>
Tested-by: Don Brace <don.brace@microsemi.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

If a drive with variable zone sizes or an invalid last zone size is
detected, the local variable this_zone_blocks is set to 0 and early return
from the function triggered, but this does not result in an error return.
The local variable zone_blocks must be set to 0 for an error to be
returned.

[mkp: typo in commit description]

Fixes: ccce20fc ("scsi: sd_zbc: Avoid that resetting a zone fails sporadically")
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

For one GFP_DMA32 does not actually work with kmalloc, as we only have
GFP_DMA and GFP_KERNEL caches, but not GFP_DMA32.  Second the memory
is mapped using the proper DMA API anyway, which would include proper
bounce buffering if needed by the device.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Pull workqueue updates from Tejun Heo:

 - make kworkers report the workqueue it is executing or has executed
   most recently in /proc/PID/comm (so they show up in ps/top)

 - CONFIG_SMP shuffle to move stuff which isn't necessary for UP builds
   inside CONFIG_SMP.

* 'for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: move function definitions within CONFIG_SMP block
  workqueue: Make sure struct worker is accessible for wq_worker_comm()
  workqueue: Show the latest workqueue name in /proc/PID/{comm,stat,status}
  proc: Consolidate task->comm formatting into proc_task_name()
  workqueue: Set worker->desc to workqueue name by default
  workqueue: Make worker_attach/detach_pool() update worker->pool
  workqueue: Replace pool->attach_mutex with global wq_pool_attach_mutex

Pull cgroup updates from Tejun Heo:

 - For cpustat, cgroup has a percpu hierarchical stat mechanism which
   propagates up the hierarchy lazily.

   This contains commits to factor out and generalize the mechanism so
   that it can be used for other cgroup stats too.

   The original intention was to update memcg stats to use it but memcg
   went for a different approach, so still the only user is cpustat. The
   factoring out and generalization still make sense and it's likely
   that this can be used for other purposes in the future.

 - cgroup uses kernfs_notify() (which uses fsnotify()) to inform user
   space of certain events. A rate limiting mechanism is added.

 - Other misc changes.

* 'for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: css_set_lock should nest inside tasklist_lock
  rdmacg: Convert to use match_string() helper
  cgroup: Make cgroup_rstat_updated() ready for root cgroup usage
  cgroup: Add memory barriers to plug cgroup_rstat_updated() race window
  cgroup: Add cgroup_subsys->css_rstat_flush()
  cgroup: Replace cgroup_rstat_mutex with a spinlock
  cgroup: Factor out and expose cgroup_rstat_*() interface functions
  cgroup: Reorganize kernel/cgroup/rstat.c
  cgroup: Distinguish base resource stat implementation from rstat
  cgroup: Rename stat to rstat
  cgroup: Rename kernel/cgroup/stat.c to kernel/cgroup/rstat.c
  cgroup: Limit event generation frequency
  cgroup: Explicitly remove core interface files

Pull libata updates from Tejun Heo:

 - libata has always been limiting the maximum queue depth to 31, with
   one entry set aside mostly for historical reasons. This didn't use to
   make much difference but Jens found out that modern hard drives can
   actually perform measurably better with the extra one queue depth.
   Jens updated libata core so that it can make use of full 32 queue
   depth

 - Damien updated command retry logic in error handling so that it
   doesn't unnecessarily retry when upper layer (SCSI) is gonna handle
   them

 - A couple misc changes

* 'for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  sata_fsl: use the right type for tag bitshift
  ahci: enable full queue depth of 32
  libata: don't clamp queue depth to ATA_MAX_QUEUE - 1
  libata: add extra internal command
  sata_nv: set host can_queue count appropriately
  libata: remove assumption that ATA_MAX_QUEUE - 1 is the max
  libata: use ata_tag_internal() consistently
  libata: bump ->qc_active to a 64-bit type
  libata: convert core and drivers to ->hw_tag usage
  libata: introduce notion of separate hardware tags
  libata: Fix command retry decision
  libata: Honor RQF_QUIET flag
  libata: Make ata_dev_set_mode() less verbose
  libata: Fix ata_err_string()
  libata: Fix comment typo in ata_eh_analyze_tf()
  sata_nv: don't use block layer bounce buffer
  ata: hpt37x: Convert to use match_string() helper

Pull libata fixes from Tejun Heo:
 "These two are fixes which missed v4.17.

  One is to remove an incorrect power management blacklist entry and the
  other to fix a cdb buffer overrun which has been there for a very long
  time"

* 'for-4.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  libata: Drop SanDisk SD7UB3Q*G1001 NOLPM quirk
  libata: zpodd: small read overflow in eject_tray()

Pull tty/serial updates from Greg KH:
 "Here is the big tty/serial driver update for 4.18-rc1.

  There's nothing major here, just lots of serial driver updates. Full
  details are in the shortlog, nothing anything specific to call out
  here.

  All have been in linux-next for a while with no reported issues"

* tag 'tty-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (55 commits)
  vt: Perform safe console erase only once
  serial: imx: disable UCR4_OREN on shutdown
  serial: imx: drop CTS/RTS handling from shutdown
  tty: fix typo in ASYNCB_FOURPORT comment
  serial: samsung: check DMA engine capabilities before using DMA mode
  tty: Fix data race in tty_insert_flip_string_fixed_flag
  tty: serial: msm_geni_serial: Fix TX infinite loop
  serial: 8250_dw: Fix runtime PM handling
  serial: 8250: omap: Fix idling of clocks for unused uarts
  tty: serial: drop ATH79 specific SoC symbols
  serial: 8250: Add missing rxtrig_bytes on Altera 16550 UART
  serial/aspeed-vuart: fix a couple mod_timer() calls
  serial: sh-sci: Use spin_{try}lock_irqsave instead of open coding version
  serial: 8250_of: Add IO space support
  tty/serial: atmel: use port->name as name in request_irq()
  serial: imx: dma_unmap_sg buffers on shutdown
  serial: imx: cleanup imx_uart_disable_dma()
  tty: serial: qcom_geni_serial: Add early console support
  tty: serial: qcom_geni_serial: Return IRQ_NONE for spurious interrupts
  tty: serial: qcom_geni_serial: Use iowrite32_rep to write to FIFO
  ...

Merge tag 'driver-core-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core updates from Greg KH:
 "Here is the driver core patchset for 4.18-rc1.

  The large chunk of these are firmware core documentation and api
  updates. Nothing major there, just better descriptions for others to
  be able to understand the firmware code better. There's also a user
  for a new firmware api call.

  Other than that, there are some minor updates for debugfs, kernfs, and
  the driver core itself.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'driver-core-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (23 commits)
  driver core: hold dev's parent lock when needed
  driver-core: return EINVAL error instead of BUG_ON()
  driver core: add __printf verification to device_create_groups_vargs
  mm: memory_hotplug: use put_device() if device_register fail
  base: core: fix typo 'can by' to 'can be'
  debugfs: inode: debugfs_create_dir uses mode permission from parent
  debugfs: Re-use kstrtobool_from_user()
  Documentation: clarify firmware_class provenance and why we can't rename the module
  Documentation: remove stale firmware API reference
  Documentation: fix few typos and clarifications for the firmware loader
  ath10k: re-enable the firmware fallback mechanism for testmode
  ath10k: use firmware_request_nowarn() to load firmware
  firmware: add firmware_request_nowarn() - load firmware without warnings
  firmware_loader: make firmware_fallback_sysfs() print more useful
  firmware_loader: move kconfig FW_LOADER entries to its own file
  firmware_loader: replace ---help--- with help
  firmware_loader: enhance Kconfig documentation over FW_LOADER
  firmware_loader: document firmware_sysfs_fallback()
  firmware: rename fw_sysfs_fallback to firmware_fallback_sysfs()
  firmware: use () to terminate kernel-doc function names
  ...

Pull char/misc driver updates from Greg KH:
 "Here is the "big" char and misc driver patches for 4.18-rc1.

  It's not a lot of stuff here, but there are some highlights:

   - coreboot driver updates

   - soundwire driver updates

   - android binder updates

   - fpga big sync, mostly documentation

   - lots of minor driver updates

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (81 commits)
  vmw_balloon: fixing double free when batching mode is off
  MAINTAINERS: Add driver-api/fpga path
  fpga: clarify that unregister functions also free
  documentation: fpga: move fpga-region.txt to driver-api
  documentation: fpga: add bridge document to driver-api
  documentation: fpga: move fpga-mgr.txt to driver-api
  Documentation: fpga: move fpga overview to driver-api
  fpga: region: kernel-doc fixes
  fpga: bridge: kernel-doc fixes
  fpga: mgr: kernel-doc fixes
  fpga: use SPDX
  fpga: region: change api, add fpga_region_create/free
  fpga: bridge: change api, don't use drvdata
  fpga: manager: change api, don't use drvdata
  fpga: region: don't use drvdata in common fpga code
  Drivers: hv: vmbus: Removed an unnecessary cast from void *
  ver_linux: Drop redundant calls to system() to test if file is readable
  ver_linux: Move stderr redirection from function parameter to function body
  misc: IBM Virtual Management Channel Driver (VMC)
  rpmsg: Correct support for MODULE_DEVICE_TABLE()
  ...

Pull USB and PHY updates from Greg KH:
 "Here is the big USB pull request for 4.18-rc1.

  Lots of stuff here, the highlights are:

   - phy driver updates and new additions

   - usual set of xhci driver updates

   - normal set of musb updates

   - gadget driver updates and new controllers

   - typec work, it's getting closer to getting fully out of the staging
     portion of the tree.

   - lots of minor cleanups and bugfixes.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
  Revert "xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue"
  xhci: Add quirk to zero 64bit registers on Renesas PCIe controllers
  xhci: Allow more than 32 quirks
  usb: xhci: force all memory allocations to node
  selftests: add test for USB over IP driver
  USB: typec: fsusb302: no need to check return value of debugfs_create_dir()
  USB: gadget: udc: s3c2410_udc: no need to check return value of debugfs_create functions
  USB: gadget: udc: renesas_usb3: no need to check return value of debugfs_create functions
  USB: gadget: udc: pxa27x_udc: no need to check return value of debugfs_create functions
  USB: gadget: udc: gr_udc: no need to check return value of debugfs_create functions
  USB: gadget: udc: bcm63xx_udc: no need to check return value of debugfs_create functions
  USB: udc: atmel_usba_udc: no need to check return value of debugfs_create functions
  USB: dwc3: no need to check return value of debugfs_create functions
  USB: dwc2: no need to check return value of debugfs_create functions
  USB: core: no need to check return value of debugfs_create functions
  USB: chipidea: no need to check return value of debugfs_create functions
  USB: ehci-hcd: no need to check return value of debugfs_create functions
  USB: fhci-hcd: no need to check return value of debugfs_create functions
  USB: fotg210-hcd: no need to check return value of debugfs_create functions
  USB: imx21-hcd: no need to check return value of debugfs_create functions
  ...

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Decrease polling rate for erase/trim/discard
   - Allow non-sleeping GPIOs for card detect
   - Improve mmc block removal path
   - Enable support for mmc_sw_reset() for SDIO cards
   - Add mmc_sw_reset() to allow users to do a soft reset of the card
   - Allow power delay to be tunable via DT
   - Allow card detect debounce delay to be tunable via DT
   - Enable new quirk to limit clock rate for Marvell 8887 chip
   - Don't show eMMC RPMB and BOOT areas in /proc/partitions
   - Add capability to avoid 3.3V signaling for fragile HWs

  MMC host:
   - Improve/fixup support for handle highmem pages
   - Remove depends on HAS_DMA in case of platform dependency
   - mvsdio: Enable support for erase/trim/discard
   - rtsx_usb: Enable support for erase/trim/discard
   - renesas_sdhi: Fix WP logic regressions
   - renesas_sdhi: Add r8a77965 support
   - renesas_sdhi: Add R8A77980 to whitelist
   - meson: Add optional support for device reset
   - meson: Add support for the Meson-AXG platform
   - dw_mmc: Add new driver for BlueField DW variant
   - mediatek: Add support for 64G DRAM DMA
   - sunxi: Deploy runtime PM support
   - jz4740: Add support for JZ4780
   - jz4740: Enable support for DT based platforms
   - sdhci: Various improvement to timeout handling
   - sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
   - sdhci-omap: Add support for controller in k2g SoC
   - sdhci-omap: Add workarounds for a couple of Erratas
   - sdhci-omap: Enable support for generic sdhci DT properties
   - sdhci-cadence: Re-send tune request to deal with errata
   - sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
   - sdhci-pci: Avoid 3.3V signaling on some NI 904x
   - sdhci-esdhc-imx: Use watermark levels for PIO access
   - sdhci-msm: Improve card detection handling
   - sdhci-msm: Add support voltage pad switching"

* tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (104 commits)
  mmc: renesas_sdhi: really fix WP logic regressions
  mmc: mvsdio: Enable MMC_CAP_ERASE
  mmc: mvsdio: Respect card busy time out from mmc core
  mmc: sdhci-msm: Remove NO_CARD_NO_RESET quirk
  mmc: sunxi: Use ifdef rather than __maybe_unused
  mmc: mxmmc: Use ifdef rather than __maybe_unused
  mmc: mxmmc: include linux/highmem.h
  mmc: sunxi: mark PM functions as __maybe_unused
  mmc: Throttle calls to MMC_SEND_STATUS during mmc_do_erase()
  mmc: au1xmmc: handle highmem pages
  mmc: Allow non-sleeping GPIO cd
  mmc: sdhci-*: Don't emit error msg if sdhci_add_host() fails
  mmc: sd: Define name for default speed dtr
  mmc: core: Move calls to ->prepare_hs400_tuning() closer to mmc code
  mmc: sdhci-xenon: use match_string() helper
  mmc: wbsd: handle highmem pages
  mmc: ushc: handle highmem pages
  mmc: mxcmmc: handle highmem pages
  mmc: atmel-mci: use sg_copy_{from,to}_buffer
  mmc: android-goldfish: use sg_copy_{from,to}_buffer
  ...

Merge tag 'leds_for_4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds

Pull LED updates from Jacek Anaszewski:
 "This was quite a fruitful cycle, taking into account usual traffic on
  linux-leds list, as we managed to merge three new LED class drivers.

  New LED class drivers with related DT bindings:
   - add LED driver for CR0014114 board
   - add Spreadtrum SC27xx breathing light controller driver
   - introduce the lm3601x LED driver

  LED class fix:
   - ensure workqueue is initialized before setting brightness

  Improvements and fixes to existing LED class drivers:
   - fix return value check in sc27xx_led_probe()
   - use sysfs_match_string() helper in wm831x_status_src_store()"

* tag 'leds_for_4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
  leds: class: ensure workqueue is initialized before setting brightness
  leds: lm3601x: Introduce the lm3601x LED driver
  dt: bindings: lm3601x: Introduce the lm3601x driver
  leds: sc27xx: Fix return value check in sc27xx_led_probe()
  leds: Add Spreadtrum SC27xx breathing light controller driver
  dt-bindings: leds: Add SC27xx breathing light controller documentation
  leds: wm831x-status: Use sysfs_match_string() helper
  leds: add LED driver for CR0014114 board
  dt-bindings: Add vendor prefix and docs for CR0014114

Pull input updates from Dmitry Torokhov:

 - a new driver to ChipOne icn8505 based touchscreens

 - on certain systems with Elan touch controllers they will be switched
   away form PS/2 emulation and over to native SMbus mode

 - assorted driver fixups and improvements

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (24 commits)
  Input: elan_i2c - add ELAN0612 (Lenovo v330 14IKB) ACPI ID
  Input: goodix - add new ACPI id for GPD Win 2 touch screen
  Input: xpad - add GPD Win 2 Controller USB IDs
  Input: ti_am335x_tsc - prevent system suspend when TSC is in use
  Input: ti_am335x_tsc - ack pending IRQs at probe and before suspend
  Input: cros_ec_keyb - mark cros_ec_keyb driver as wake enabled device.
  Input: mk712 - update documentation web link
  Input: atmel_mxt_ts - fix reset-gpio for level based irqs
  Input: atmel_mxt_ts - require device properties present when probing
  Input: psmouse-smbus - allow to control psmouse_deactivate
  Input: elantech - detect new ICs and setup Host Notify for them
  Input: elantech - add support for SMBus devices
  Input: elantech - query the resolution in query_info
  Input: elantech - split device info into a separate structure
  Input: elan_i2c - add trackstick report
  Input: usbtouchscreen - add sysfs attribute for 3M MTouch firmware rev
  Input: ati_remote2 - fix typo 'can by' to 'can be'
  Input: replace hard coded string with __func__ in pr_err()
  Input: add support for ChipOne icn8505 based touchscreens
  Input: gamecon - avoid using __set_bit() for capabilities
  ...

Pull crypto updates from Herbert Xu:
 "API:

   - Decryption test vectors are now automatically generated from
     encryption test vectors.

  Algorithms:

   - Fix unaligned access issues in crc32/crc32c.

   - Add zstd compression algorithm.

   - Add AEGIS.

   - Add MORUS.

  Drivers:

   - Add accelerated AEGIS/MORUS on x86.

   - Add accelerated SM4 on arm64.

   - Removed x86 assembly salsa implementation as it is slower than C.

   - Add authenc(hmac(sha*), cbc(aes)) support in inside-secure.

   - Add ctr(aes) support in crypto4xx.

   - Add hardware key support in ccree.

   - Add support for new Centaur CPU in via-rng"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (112 commits)
  crypto: chtls - free beyond end rspq_skb_cache
  crypto: chtls - kbuild warnings
  crypto: chtls - dereference null variable
  crypto: chtls - wait for memory sendmsg, sendpage
  crypto: chtls - key len correction
  crypto: salsa20 - Revert "crypto: salsa20 - export generic helpers"
  crypto: x86/salsa20 - remove x86 salsa20 implementations
  crypto: ccp - Add GET_ID SEV command
  crypto: ccp - Add DOWNLOAD_FIRMWARE SEV command
  crypto: qat - Add MODULE_FIRMWARE for all qat drivers
  crypto: ccree - silence debug prints
  crypto: ccree - better clock handling
  crypto: ccree - correct host regs offset
  crypto: chelsio - Remove separate buffer used for DMA map B0 block in CCM
  crypt: chelsio - Send IV as Immediate for cipher algo
  crypto: chelsio - Return -ENOSPC for transient busy indication.
  crypto: caam/qi - fix warning in init_cgr()
  crypto: caam - fix rfc4543 descriptors
  crypto: caam - fix MC firmware detection
  crypto: clarify licensing of OpenSSL asm code
  ...

Pull fscrypt updates from Ted Ts'o:
 "Add bunch of cleanups, and add support for the Speck128/256
  algorithms.

  Yes, Speck is contrversial, but the intention is to use them only for
  the lowest end Android devices, where the alternative *really* is no
  encryption at all for data stored at rest"

* tag 'fscrypt_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/fscrypt:
  fscrypt: log the crypto algorithm implementations
  fscrypt: add Speck128/256 support
  fscrypt: only derive the needed portion of the key
  fscrypt: separate key lookup from key derivation
  fscrypt: use a common logging function
  fscrypt: remove internal key size constants
  fscrypt: remove unnecessary check for non-logon key type
  fscrypt: make fscrypt_operations.max_namelen an integer
  fscrypt: drop empty name check from fname_decrypt()
  fscrypt: drop max_namelen check from fname_decrypt()
  fscrypt: don't special-case EOPNOTSUPP from fscrypt_get_encryption_info()
  fscrypt: don't clear flags on crypto transform
  fscrypt: remove stale comment from fscrypt_d_revalidate()
  fscrypt: remove error messages for skcipher_request_alloc() failure
  fscrypt: remove unnecessary NULL check when allocating skcipher
  fscrypt: clean up after fscrypt_prepare_lookup() conversions
  fs, fscrypt: only define ->s_cop when FS_ENCRYPTION is enabled
  fscrypt: use unbound workqueue for decryption

Pull xfs updates from Darrick Wong:
 "New features this cycle include the ability to relabel mounted
  filesystems, support for fallocated swapfiles, and using FUA for pure
  data O_DSYNC directio writes. With this cycle we begin to integrate
  online filesystem repair and refactor the growfs code in preparation
  for eventual subvolume support, though the road ahead for both
  features is quite long.

  There are also numerous refactorings of the iomap code to remove
  unnecessary log overhead, to disentangle some of the quota code, and
  to prepare for buffer head removal in a future upstream kernel.

  Metadata validation continues to improve, both in the hot path
  veifiers and the online filesystem check code. I anticipate sending a
  second pull request in a few days with more metadata validation
  improvements.

  This series has been run through a full xfstests run over the weekend
  and through a quick xfstests run against this morning's master, with
  no major failures reported.

  Summary:

   - Strengthen inode number and structure validation when allocating
     inodes.

   - Reduce pointless buffer allocations during cache miss

   - Use FUA for pure data O_DSYNC directio writes

   - Various iomap refactorings

   - Strengthen quota metadata verification to avoid unfixable broken
     quota

   - Make AGFL block freeing a deferred operation to avoid blowing out
     transaction reservations when running complex operations

   - Get rid of the log item descriptors to reduce log overhead

   - Fix various reflink bugs where inodes were double-joined to
     transactions

   - Don't issue discards when trimming unwritten extents

   - Refactor incore dquot initialization and retrieval interfaces

   - Fix some locking problmes in the quota scrub code

   - Strengthen btree structure checks in scrub code

   - Rewrite swapfile activation to use iomap and support unwritten
     extents

   - Make scrub exit to userspace sooner when corruptions or
     cross-referencing problems are found

   - Make scrub invoke the data fork scrubber directly on metadata
     inodes

   - Don't do background reclamation of post-eof and cow blocks when the
     fs is suspended

   - Fix secondary superblock buffer lifespan hinting

   - Refactor growfs to use table-dispatched functions instead of long
     stringy functions

   - Move growfs code to libxfs

   - Implement online fs label getting and setting

   - Introduce online filesystem repair (in a very limited capacity)

   - Fix unit conversion problems in the realtime freemap iteration
     functions

   - Various refactorings and cleanups in preparation to remove buffer
     heads in a future release

   - Reimplement the old bmap call with iomap

   - Remove direct buffer head accesses from seek hole/data

   - Various bug fixes"

* tag 'xfs-4.18-merge-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: (121 commits)
  fs: use ->is_partially_uptodate in page_cache_seek_hole_data
  fs: remove the buffer_unwritten check in page_seek_hole_data
  fs: move page_cache_seek_hole_data to iomap.c
  xfs: use iomap_bmap
  iomap: add an iomap-based bmap implementation
  iomap: add a iomap_sector helper
  iomap: use __bio_add_page in iomap_dio_zero
  iomap: move IOMAP_F_BOUNDARY to gfs2
  iomap: fix the comment describing IOMAP_NOWAIT
  iomap: inline data should be an iomap type, not a flag
  mm: split ->readpages calls to avoid non-contiguous pages lists
  mm: return an unsigned int from __do_page_cache_readahead
  mm: give the 'ret' variable a better name __do_page_cache_readahead
  block: add a lower-level bio_add_page interface
  xfs: fix error handling in xfs_refcount_insert()
  xfs: fix xfs_rtalloc_rec units
  xfs: strengthen rtalloc query range checks
  xfs: xfs_rtbuf_get should check the bmapi_read results
  xfs: xfs_rtword_t should be unsigned, not signed
  dax: change bdev_dax_supported() to support boolean returns
  ...

Pull ext4 updates from Ted Ts'o:
 "A lot of cleanups and bug fixes, especially dealing with corrupted
  file systems"

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (23 commits)
  ext4: fix fencepost error in check for inode count overflow during resize
  ext4: correctly handle a zero-length xattr with a non-zero e_value_offs
  ext4: bubble errors from ext4_find_inline_data_nolock() up to ext4_iget()
  ext4: do not allow external inodes for inline data
  ext4: report delalloc reserve as non-free in statfs for project quota
  ext4: remove NULL check before calling kmem_cache_destroy()
  jbd2: remove NULL check before calling kmem_cache_destroy()
  jbd2: remove bunch of empty lines with jbd2 debug
  ext4: handle errors on ext4_commit_super
  ext4: do not update s_last_mounted of a frozen fs
  ext4: factor out helper ext4_sample_last_mounted()
  vfs: add the sb_start_intwrite_trylock() helper
  ext4: update mtime in ext4_punch_hole even if no blocks are released
  ext4: add verifier check for symlink with append/immutable flags
  fs: ext4: add new return type vm_fault_t
  ext4: fix hole length detection in ext4_ind_map_blocks()
  ext4: mark block bitmap corrupted when found
  ext4: mark inode bitmap corrupted when found
  ext4: add new ext4_mark_group_bitmap_corrupted() helper
  ext4: fix wrong return value in ext4_read_inode_bitmap()
  ...

Pull s390 updates from Martin Schwidefsky:

 - A rework for the s390 arch random code, the TRNG instruction is
   rather slow and should not be used on the interrupt path

 - A fix for a memory leak in the zcrypt driver

 - Changes to the early boot code to add a compile time check for code
   that may not use the .bss section, with the goal to avoid initrd
   corruptions

 - Add an interface to get the physical network ID (pnetid), this is
   useful to group network devices that are attached to the same network

 - Some cleanup for the linker script

 - Some code improvement for the dasd driver

 - Two fixes for the perf sampling support

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/zcrypt: Fix CCA and EP11 CPRB processing failure memory leak.
  s390/archrandom: Rework arch random implementation.
  s390/net: add pnetid support
  s390/dasd: simplify locking in dasd_times_out
  s390/cio: add test for ccwgroup device
  s390/cio: add helper to query utility strings per given ccw device
  s390: remove no-op macro VMLINUX_SYMBOL()
  s390: remove closung punctuation from spectre messages
  s390: introduce compile time check for empty .bss section
  s390/early: move functions which may not access bss section to extra file
  s390/early: get rid of #ifdef CONFIG_BLK_DEV_INITRD
  s390/early: get rid of memmove_early
  s390/cpum_sf: Add data entry sizes to sampling trailer entry
  perf: fix invalid bit in diagnostic entry

Pull m68knommu updates from Greg Ungerer:
 "These changes all relate to converting the IO access functions for the
  ColdFire (and all other non-MMU m68k) platforms to use asm-generic IO
  instead.

  This makes the IO support the same on all ColdFire (regardless of MMU
  enabled or not) and means we can now support PCI in non-MMU mode.

  As a bonus these changes remove more code than they add"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68k: fix ColdFire PCI config reads and writes
  m68k: introduce iomem() macro for __iomem conversions
  m68k: allow ColdFire PCI bus on MMU and non-MMU configuration
  m68k: fix ioremapping for internal ColdFire peripherals
  m68k: fix read/write multi-byte IO for PCI on ColdFire
  m68k: don't redefine access functions if we have PCI
  m68k: remove old ColdFire IO access support code
  m68k: use io_no.h for MMU and non-MMU enabled ColdFire
  m68k: setup PCI support code in io_no.h
  m68k: group io mapping definitions and functions
  m68k: rework raw access macros for the non-MMU case
  m68k: use asm-generic/io.h for non-MMU io access functions
  m68k: put definition guards around virt_to_phys and phys_to_virt
  m68k: move *_relaxed macros into io_no.h and io_mm.h

Pull reed-salomon library updates from Kees Cook:
 "Refactors rslib and callers to provide a per-instance allocation area
  instead of performing VLAs on the stack"

* tag 'rslib-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  rslib: Allocate decoder buffers to avoid VLAs
  mtd: rawnand: diskonchip: Allocate rs control per instance
  rslib: Split rs control struct
  rslib: Simplify error path
  rslib: Remove GPL boilerplate
  rslib: Add SPDX identifiers
  rslib: Cleanup top level comments
  rslib: Cleanup whitespace damage
  dm/verity_fec: Use GFP aware reed solomon init
  rslib: Add GFP aware init function

Pull device properties framework update from Rafael Wysocki:
 "Modify the device properties framework to remove union aliasing from
  it (Andy Shevchenko)"

* tag 'dp-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  device property: Get rid of union aliasing

Pull ACPI updates from Rafael Wysocki:
 "These update the ACPICA code in the kernel to the 20180508 upstream
  revision and make it support the RT patch, add CPPC v3 support to the
  ACPI CPPC library, add a WDAT-based watchdog quirk to prevent clashes
  with the RTC, add quirks to the ACPI AC and battery drivers, and
  update the ACPI SoC drivers.

  Specifics:

   - Update the ACPICA code in the kernel to the 20180508 upstream
     revision including:
       * iASL -tc option enhancement (Bob Moore).
       * Debugger improvements (Bob Moore).
       * Support for tables larger than 1 MB in acpidump/acpixtract (Bob
         Moore).
       * Minor fixes and cleanups (Colin Ian King, Toomas Soome).

   - Make the ACPICA code in the kernel support the RT patch (Sebastian
     Andrzej Siewior, Steven Rostedt).

   - Add a kmemleak annotation to the ACPICA code (Larry Finger).

   - Add CPPC v3 support to the ACPI CPPC library and fix two issues
     related to CPPC (Prashanth Prakash, Al Stone).

   - Add an ACPI WDAT-based watchdog quirk to prefer iTCO_wdt on systems
     where WDAT clashes with the RTC SRAM (Mika Westerberg).

   - Add some quirks to the ACPI AC and battery drivers (Carlo Caione,
     Hans de Goede).

   - Update the ACPI SoC drivers for Intel (LPSS) and AMD (APD)
     platforms (Akshu Agrawal, Hans de Goede).

   - Fix up some assorted minor issues (Al Stone, Laszlo Toth, Mathieu
     Malaterre)"

* tag 'acpi-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
  ACPICA: Mark acpi_ut_create_internal_object_dbg() memory allocations as non-leaks
  ACPI / watchdog: Prefer iTCO_wdt always when WDAT table uses RTC SRAM
  mailbox: PCC: erroneous error message when parsing ACPI PCCT
  ACPICA: Update version to 20180508
  ACPICA: acpidump/acpixtract: Support for tables larger than 1MB
  ACPI: APD: Add AMD misc clock handler support
  clk: x86: Add ST oscout platform clock
  ACPICA: Update version to 20180427
  ACPICA: Debugger: Removed direct support for EC address space in "Test Objects"
  ACPICA: Debugger: Add Package support for "test objects" command
  ACPICA: Improve error messages for the namespace root node
  ACPICA: Fix potential infinite loop in acpi_rs_dump_byte_list
  ACPICA: vsnprintf: this statement may fall through
  ACPICA: Tables: Fix spelling mistake in comment
  ACPICA: iASL: Enhance the -tc option (create AML hex file in C)
  ACPI: Add missing prototype_for arch_post_acpi_subsys_init()
  ACPI / tables: improve comments regarding acpi_parse_entries_array()
  ACPICA: Convert acpi_gbl_hardware lock back to an acpi_raw_spinlock
  ACPICA: provide abstraction for raw_spinlock_t
  ACPI / CPPC: Fix invalid PCC channel status errors
  ...

Pull power management updates from Rafael Wysocki:
 "These include a significant update of the generic power domains
  (genpd) and Operating Performance Points (OPP) frameworks, mostly
  related to the introduction of power domain performance levels,
  cpufreq updates (new driver for Qualcomm Kryo processors, updates of
  the existing drivers, some core fixes, schedutil governor
  improvements), PCI power management fixes, ACPI workaround for
  EC-based wakeup events handling on resume from suspend-to-idle, and
  major updates of the turbostat and pm-graph utilities.

  Specifics:

   - Introduce power domain performance levels into the the generic
     power domains (genpd) and Operating Performance Points (OPP)
     frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).

   - Fix two issues in the runtime PM framework related to the
     initialization and removal of devices using device links (Ulf
     Hansson).

   - Clean up the initialization of drivers for devices in PM domains
     (Ulf Hansson, Geert Uytterhoeven).

   - Fix a cpufreq core issue related to the policy sysfs interface
     causing CPU online to fail for CPUs sharing one cpufreq policy in
     some situations (Tao Wang).

   - Make it possible to use platform-specific suspend/resume hooks in
     the cpufreq-dt driver and make the Armada 37xx DVFS use that
     feature (Viresh Kumar, Miquel Raynal).

   - Optimize policy transition notifications in cpufreq (Viresh Kumar).

   - Improve the iowait boost mechanism in the schedutil cpufreq
     governor (Patrick Bellasi).

   - Improve the handling of deferred frequency updates in the schedutil
     cpufreq governor (Joel Fernandes, Dietmar Eggemann, Rafael Wysocki,
     Viresh Kumar).

   - Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).

   - Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
     Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman, Viresh
     Kumar).

   - Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag set
     and update stale comments in the PCI core PM code (Rafael Wysocki).

   - Work around an issue related to the handling of EC-based wakeup
     events in the ACPI PM core during resume from suspend-to-idle if
     the EC has been put into the low-power mode (Rafael Wysocki).

   - Improve the handling of wakeup source objects in the PM core (Doug
     Berger, Mahendran Ganesh, Rafael Wysocki).

   - Update the driver core to prevent deferred probe from breaking
     suspend/resume ordering (Feng Kan).

   - Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
     Wysocki).

   - Make the core suspend/resume code and cpufreq support the RT patch
     (Sebastian Andrzej Siewior, Thomas Gleixner).

   - Consolidate the PM QoS handling in cpuidle governors (Rafael
     Wysocki).

   - Fix a possible crash in the hibernation core (Tetsuo Handa).

   - Update the rockchip-io Adaptive Voltage Scaling (AVS) driver (David
     Wu).

   - Update the turbostat utility (fixes, cleanups, new CPU IDs, new
     command line options, built-in "Low Power Idle" counters support,
     new POLL and POLL% columns) and add an entry for it to MAINTAINERS
     (Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
     Prarit Bhargava, Srinivas Pandruvada).

   - Update the pm-graph to version 5.1 (Todd Brandt).

   - Update the intel_pstate_tracer utility (Doug Smythies)"

* tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (128 commits)
  tools/power turbostat: update version number
  tools/power turbostat: Add Node in output
  tools/power turbostat: add node information into turbostat calculations
  tools/power turbostat: remove num_ from cpu_topology struct
  tools/power turbostat: rename num_cores_per_pkg to num_cores_per_node
  tools/power turbostat: track thread ID in cpu_topology
  tools/power turbostat: Calculate additional node information for a package
  tools/power turbostat: Fix node and siblings lookup data
  tools/power turbostat: set max_num_cpus equal to the cpumask length
  tools/power turbostat: if --num_iterations, print for specific number of iterations
  tools/power turbostat: Add Cannon Lake support
  tools/power turbostat: delete duplicate #defines
  x86: msr-index.h: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
  tools/power turbostat: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
  tools/power turbostat: add POLL and POLL% column
  tools/power turbostat: Fix --hide Pk%pc10
  tools/power turbostat: Build-in "Low Power Idle" counters support
  tools/power turbostat: Don't make man pages executable
  tools/power turbostat: remove blank lines
  tools/power turbostat: a small C-states dump readability immprovement
  ...

Pull block fixes from Jens Axboe:
 "This just contains the dm kzalloc fix that was discussed, and a fix
  that I queued up yesterday for a case where blk-mq doesn't honor the
  stop bit appropriately"

* tag 'for-linus-20180605' of git://git.kernel.dk/linux-block:
  dm: Use kzalloc for all structs with embedded biosets/mempools
  blk-mq: return when hctx is stopped in blk_mq_run_work_fn

Merge faddr2line updates from Josh Poimboeuf:

 - revert faddr2line's default output to its original non-code-listing
   output, and make the code listing an optional feature

 - give faddr2line a real maintainer, so get_maintainer.pl will actually
   CC me on future patches

* emailed patches from Josh Poimboeuf <jpoimboe@redhat.com>:
  MAINTAINERS: add Josh Poimboeuf as faddr2line maintainer
  scripts/faddr2line: make the new code listing format optional

... so I finally get credit for my greatest accomplishment.

And, less importantly, so get_maintainer.pl will actually CC me on
future patches.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 6870c016 ("scripts/faddr2line: show the code context")
radically altered the output format of the faddr2line tool.  And while
the new list output format might have merit it broke my vim usage and
was hard to read.

Make the new format optional; using a '--list' argument and attempt to
make the output slightly easier to read by adding a little whitespace to
separate the different files and explicitly mark the line in question.

Cc: Changbin Du <changbin.du@intel.com>
Fixes: 6870c016 ("scripts/faddr2line: show the code context")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mempool_init()/bioset_init() require that the mempools/biosets be zeroed
first; they probably should not _require_ this, but not allocating those
structs with kzalloc is a fairly nonsensical thing to do (calling
mempool_exit()/bioset_exit() on an uninitialized mempool/bioset is legal
and safe, but only works if said memory was zeroed.)
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull x86 hyperv updates from Thomas Gleixner:
 "A set of commits to enable APIC enlightenment when running as a guest
  on Microsoft HyperV.

  This accelerates the APIC access with paravirtualization techniques,
  which are called enlightenments on Hyper-V"

* 'x86-hyperv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/Hyper-V/hv_apic: Build the Hyper-V APIC conditionally
  x86/Hyper-V/hv_apic: Include asm/apic.h
  X86/Hyper-V: Consolidate the allocation of the hypercall input page
  X86/Hyper-V: Consolidate code for converting cpumask to vpset
  X86/Hyper-V: Enhanced IPI enlightenment
  X86/Hyper-V: Enable IPI enlightenments
  X86/Hyper-V: Enlighten APIC access

Pull x86 cache resource controller updates from Thomas Gleixner:
 "An update for the Intel Resource Director Technolgy (RDT) which adds a
  feedback driven software controller to runtime adjust the bandwidth
  allocation MSRs.

  This makes the allocations more accurate and allows to use bandwidth
  values in understandable units (MB/s) instead of using percentage
  based allocations as the original, still available, interface.

  The software controller can be enabled with a new mount option for the
  resctrl filesystem"

* 'x86-cache-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/intel_rdt/mba_sc: Feedback loop to dynamically update mem bandwidth
  x86/intel_rdt/mba_sc: Prepare for feedback loop
  x86/intel_rdt/mba_sc: Add schemata support
  x86/intel_rdt/mba_sc: Add initialization support
  x86/intel_rdt/mba_sc: Enable/disable MBA software controller
  x86/intel_rdt/mba_sc: Documentation for MBA software controller(mba_sc)

Pull time/Y2038 updates from Thomas Gleixner:

 - Consolidate SySV IPC UAPI headers

 - Convert SySV IPC to the new COMPAT_32BIT_TIME mechanism

 - Cleanup the core interfaces and standardize on the ktime_get_* naming
   convention.

 - Convert the X86 platform ops to timespec64

 - Remove the ugly temporary timespec64 hack

* 'timers-2038-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
  x86: Convert x86_platform_ops to timespec64
  timekeeping: Add more coarse clocktai/boottime interfaces
  timekeeping: Add ktime_get_coarse_with_offset
  timekeeping: Standardize on ktime_get_*() naming
  timekeeping: Clean up ktime_get_real_ts64
  timekeeping: Remove timespec64 hack
  y2038: ipc: Redirect ipc(SEMTIMEDOP, ...) to compat_ksys_semtimedop
  y2038: ipc: Enable COMPAT_32BIT_TIME
  y2038: ipc: Use __kernel_timespec
  y2038: ipc: Report long times to user space
  y2038: ipc: Use ktime_get_real_seconds consistently
  y2038: xtensa: Extend sysvipc data structures
  y2038: powerpc: Extend sysvipc data structures
  y2038: sparc: Extend sysvipc data structures
  y2038: parisc: Extend sysvipc data structures
  y2038: mips: Extend sysvipc data structures
  y2038: arm64: Extend sysvipc compat data structures
  y2038: s390: Remove unneeded ipc uapi header files
  y2038: ia64: Remove unneeded ipc uapi header files
  y2038: alpha: Remove unneeded ipc uapi header files
  ...

Pull timers and timekeeping updates from Thomas Gleixner:

 - Core infrastucture work for Y2038 to address the COMPAT interfaces:

     + Add a new Y2038 safe __kernel_timespec and use it in the core
       code

     + Introduce config switches which allow to control the various
       compat mechanisms

     + Use the new config switch in the posix timer code to control the
       32bit compat syscall implementation.

 - Prevent bogus selection of CPU local clocksources which causes an
   endless reselection loop

 - Remove the extra kthread in the clocksource code which has no value
   and just adds another level of indirection

 - The usual bunch of trivial updates, cleanups and fixlets all over the
   place

 - More SPDX conversions

* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
  clocksource/drivers/mxs_timer: Switch to SPDX identifier
  clocksource/drivers/timer-imx-tpm: Switch to SPDX identifier
  clocksource/drivers/timer-imx-gpt: Switch to SPDX identifier
  clocksource/drivers/timer-imx-gpt: Remove outdated file path
  clocksource/drivers/arc_timer: Add comments about locking while read GFRC
  clocksource/drivers/mips-gic-timer: Add pr_fmt and reword pr_* messages
  clocksource/drivers/sprd: Fix Kconfig dependency
  clocksource: Move inline keyword to the beginning of function declarations
  timer_list: Remove unused function pointer typedef
  timers: Adjust a kernel-doc comment
  tick: Prefer a lower rating device only if it's CPU local device
  clocksource: Remove kthread
  time: Change nanosleep to safe __kernel_* types
  time: Change types to new y2038 safe __kernel_* types
  time: Fix get_timespec64() for y2038 safe compat interfaces
  time: Add new y2038 safe __kernel_timespec
  posix-timers: Make compat syscalls depend on CONFIG_COMPAT_32BIT_TIME
  time: Introduce CONFIG_COMPAT_32BIT_TIME
  time: Introduce CONFIG_64BIT_TIME in architectures
  compat: Enable compat_get/put_timespec64 always
  ...

Pull x86 RAS updates from Thomas Gleixner:

 - Fix a stack out of bounds write in the MCE error injection code.

 - Avoid IPIs during CPU hotplug to read the MCx_MISC block address from
   a remote CPU. That's fragile and pointless because the block
   addresses are the same on all CPUs. So they can be read once and
   local.

 - Add support for MCE broadcasting on newer VIA Centaur CPUs.

* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/MCE/AMD: Read MCx_MISC block addresses on any CPU
  x86/MCE: Fix stack out-of-bounds write in mce-inject.c: Flags_read()
  x86/MCE: Enable MCE broadcasting on new Centaur CPUs

Pull irq updates from Thomas Gleixner:

 - Consolidation of softirq pending:

   The softirq mask and its accessors/mutators have many implementations
   scattered around many architectures. Most do the same things
   consisting in a field in a per-cpu struct (often irq_cpustat_t)
   accessed through per-cpu ops. We can provide instead a generic
   efficient version that most of them can use. In fact s390 is the only
   exception because the field is stored in lowcore.

 - Support for level!?! triggered MSI (ARM)

   Over the past couple of years, we've seen some SoCs coming up with
   ways of signalling level interrupts using a new flavor of MSIs, where
   the MSI controller uses two distinct messages: one that raises a
   virtual line, and one that lowers it. The target MSI controller is in
   charge of maintaining the state of the line.

   This allows for a much simplified HW signal routing (no need to have
   hundreds of discrete lines to signal level interrupts if you already
   have a memory bus), but results in a departure from the current idea
   the kernel has of MSIs.

 - Support for Meson-AXG GPIO irqchip

 - Large stm32 irqchip rework (suspend/resume, hierarchical domains)

 - More SPDX conversions

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
  ARM: dts: stm32: Add exti support to stm32mp157 pinctrl
  ARM: dts: stm32: Add exti support for stm32mp157c
  pinctrl/stm32: Add irq_eoi for stm32gpio irqchip
  irqchip/stm32: Add suspend/resume support for hierarchy domain
  irqchip/stm32: Add stm32mp1 support with hierarchy domain
  irqchip/stm32: Prepare common functions
  irqchip/stm32: Add host and driver data structures
  irqchip/stm32: Add suspend support
  irqchip/stm32: Add falling pending register support
  irqchip/stm32: Checkpatch fix
  irqchip/stm32: Optimizes and cleans up stm32-exti irq_domain
  irqchip/meson-gpio: Add support for Meson-AXG SoCs
  dt-bindings: interrupt-controller: New binding for Meson-AXG SoC
  dt-bindings: interrupt-controller: Fix the double quotes
  softirq/s390: Move default mutators of overwritten softirq mask to s390
  softirq/x86: Switch to generic local_softirq_pending() implementation
  softirq/sparc: Switch to generic local_softirq_pending() implementation
  softirq/powerpc: Switch to generic local_softirq_pending() implementation
  softirq/parisc: Switch to generic local_softirq_pending() implementation
  softirq/ia64: Switch to generic local_softirq_pending() implementation
  ...