- 14 Jun, 2017 40 commits
-
-
Hans de Goede authored
commit 75fb6363 upstream. commit a39be606 ("drm: Do a full device unregister when unplugging") causes backtraces like this one when unplugging an usb drm device while it is in use: usb 2-3: USB disconnect, device number 25 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 242 at drivers/gpu/drm/drm_mode_config.c:424 drm_mode_config_cleanup+0x220/0x280 [drm] ... RIP: 0010:drm_mode_config_cleanup+0x220/0x280 [drm] ... Call Trace: gm12u320_modeset_cleanup+0xe/0x10 [gm12u320] gm12u320_driver_unload+0x35/0x70 [gm12u320] drm_dev_unregister+0x3c/0xe0 [drm] drm_unplug_dev+0x12/0x60 [drm] gm12u320_usb_disconnect+0x36/0x40 [gm12u320] usb_unbind_interface+0x72/0x280 device_release_driver_internal+0x158/0x210 device_release_driver+0x12/0x20 bus_remove_device+0x104/0x180 device_del+0x1d2/0x350 usb_disable_device+0x9f/0x270 usb_disconnect+0xc6/0x260 ... [drm:drm_mode_config_cleanup [drm]] *ERROR* connector Unknown-1 leaked! ------------[ cut here ]------------ WARNING: CPU: 0 PID: 242 at drivers/gpu/drm/drm_mode_config.c:458 drm_mode_config_cleanup+0x268/0x280 [drm] ... <same Call Trace> ---[ end trace 80df975dae439ed6 ]--- general protection fault: 0000 [#1] SMP ... Call Trace: ? __switch_to+0x225/0x450 drm_mode_rmfb_work_fn+0x55/0x70 [drm] process_one_work+0x193/0x3c0 worker_thread+0x4a/0x3a0 ... RIP: drm_framebuffer_remove+0x62/0x3f0 [drm] RSP: ffffb776c39dfd98 ---[ end trace 80df975dae439ed7 ]--- After which the system is unusable this is caused by drm_dev_unregister getting called immediately on unplug, which calls the drivers unload function which calls drm_mode_config_cleanup which removes the framebuffer object while userspace is still holding a reference to it. Reverting commit a39be606 ("drm: Do a full device unregister when unplugging") leads to the following oops on unplug instead, when userspace closes the last fd referencing the drm_dev: sysfs group 'power' not found for kobject 'card1-Unknown-1' ------------[ cut here ]------------ WARNING: CPU: 0 PID: 2459 at fs/sysfs/group.c:237 sysfs_remove_group+0x80/0x90 ... RIP: 0010:sysfs_remove_group+0x80/0x90 ... Call Trace: dpm_sysfs_remove+0x57/0x60 device_del+0xfd/0x350 device_unregister+0x1a/0x60 drm_sysfs_connector_remove+0x39/0x50 [drm] drm_connector_unregister+0x5a/0x70 [drm] drm_connector_unregister_all+0x45/0xa0 [drm] drm_modeset_unregister_all+0x12/0x30 [drm] drm_dev_unregister+0xca/0xe0 [drm] drm_put_dev+0x32/0x60 [drm] drm_release+0x2f3/0x380 [drm] __fput+0xdf/0x1e0 ... ---[ end trace ecfb91ac85688bbe ]--- BUG: unable to handle kernel NULL pointer dereference at 00000000000000a8 IP: down_write+0x1f/0x40 ... Call Trace: debugfs_remove_recursive+0x55/0x1b0 drm_debugfs_connector_remove+0x21/0x40 [drm] drm_connector_unregister+0x62/0x70 [drm] drm_connector_unregister_all+0x45/0xa0 [drm] drm_modeset_unregister_all+0x12/0x30 [drm] drm_dev_unregister+0xca/0xe0 [drm] drm_put_dev+0x32/0x60 [drm] drm_release+0x2f3/0x380 [drm] __fput+0xdf/0x1e0 ... ---[ end trace ecfb91ac85688bbf ]--- This is caused by the revert moving back to drm_unplug_dev calling drm_minor_unregister which does: device_del(minor->kdev); dev_set_drvdata(minor->kdev, NULL); /* safety belt */ drm_debugfs_cleanup(minor); Causing the sysfs entries to already be removed even though we still have references to them in e.g. drm_connector. Note we must call drm_minor_unregister to notify userspace of the unplug of the device, so calling drm_dev_unregister is not completely wrong the problem is that drm_dev_unregister does too much. This commit fixes drm_unplug_dev by not only reverting commit a39be606 ("drm: Do a full device unregister when unplugging") but by also adding a call to drm_modeset_unregister_all before the drm_minor_unregister calls to make sure all sysfs entries are removed before calling device_del(minor->kdev) thereby also fixing the second set of oopses caused by just reverting the commit. Fixes: a39be606 ("drm: Do a full device unregister when unplugging") Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jeffy <jeffy.chen@rock-chips.com> Cc: Marco Diego Aurélio Mesquita <marcodiegomesquita@gmail.com> Reported-by:
Marco Diego Aurélio Mesquita <marcodiegomesquita@gmail.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Sean Paul <seanpaul@chromium.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170601115430.4113-1-hdegoede@redhat.comSigned-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jan Kara authored
commit 67a7d5f5 upstream. Currently, extent manipulation operations such as hole punch, range zeroing, or extent shifting do not record the fact that file data has changed and thus fdatasync(2) has a work to do. As a result if we crash e.g. after a punch hole and fdatasync, user can still possibly see the punched out data after journal replay. Test generic/392 fails due to these problems. Fix the problem by properly marking that file data has changed in these operations. Fixes: a4bb6b64Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Jan Kara authored
commit 4f8caa60 upstream. When ext4_map_blocks() is called with EXT4_GET_BLOCKS_ZERO to zero-out allocated blocks and these blocks are actually converted from unwritten extent the following race can happen: CPU0 CPU1 page fault page fault ... ... ext4_map_blocks() ext4_ext_map_blocks() ext4_ext_handle_unwritten_extents() ext4_ext_convert_to_initialized() - zero out converted extent ext4_zeroout_es() - inserts extent as initialized in status tree ext4_map_blocks() ext4_es_lookup_extent() - finds initialized extent write data ext4_issue_zeroout() - zeroes out new extent overwriting data This problem can be reproduced by generic/340 for the fallocated case for the last block in the file. Fix the problem by avoiding zeroing out the area we are mapping with ext4_map_blocks() in ext4_ext_convert_to_initialized(). It is pointless to zero out this area in the first place as the caller asked us to convert the area to initialized because he is just going to write data there before the transaction finishes. To achieve this we delete the special case of zeroing out full extent as that will be handled by the cases below zeroing only the part of the extent that needs it. We also instruct ext4_split_extent() that the middle of extent being split contains data so that ext4_split_extent_at() cannot zero out full extent in case of ENOSPC. Fixes: 12735f88Signed-off-by:
-
Konstantin Khlebnikov authored
commit 887a9730 upstream. ext4_expand_extra_isize() should clear only space between old and new size. Fixes: 6dd4ee7c # v2.6.23 Signed-off-by:
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by:
-
Jan Kara authored
commit 7d95eddf upstream. Currently, SEEK_HOLE implementation in ext4 may both return that there's a hole at some offset although that offset already has data and skip some holes during a search for the next hole. The first problem is demostrated by: xfs_io -c "falloc 0 256k" -c "pwrite 0 56k" -c "seek -h 0" file wrote 57344/57344 bytes at offset 0 56 KiB, 14 ops; 0.0000 sec (2.054 GiB/sec and 538461.5385 ops/sec) Whence Result HOLE 0 Where we can see that SEEK_HOLE wrongly returned offset 0 as containing a hole although we have written data there. The second problem can be demonstrated by: xfs_io -c "falloc 0 256k" -c "pwrite 0 56k" -c "pwrite 128k 8k" -c "seek -h 0" file wrote 57344/57344 bytes at offset 0 56 KiB, 14 ops; 0.0000 sec (1.978 GiB/sec and 518518.5185 ops/sec) wrote 8192/8192 bytes at offset 131072 8 KiB, 2 ops; 0.0000 sec (2 GiB/sec and 500000.0000 ops/sec) Whence Result HOLE 139264 Where we can see that hole at offsets 56k..128k has been ignored by the SEEK_HOLE call. The underlying problem is in the ext4_find_unwritten_pgoff() which is just buggy. In some cases it fails to update returned offset when it finds a hole (when no pages are found or when the first found page has higher index than expected), in some cases conditions for detecting hole are just missing (we fail to detect a situation where indices of returned pages are not contiguous). Fix ext4_find_unwritten_pgoff() to properly detect non-contiguous page indices and also handle all cases where we got less pages then expected in one place and handle it properly there. Fixes: c8c0df24 CC: Zheng Liu <wenqing.lz@taobao.com> Signed-off-by:
-
Julien Grall authored
commit 753c09b5 upstream. Commit 5995a68a "xen/privcmd: Add support for Linux 64KB page granularity" did not go far enough to support 64KB in mmap_batch_fn. The variable 'nr' is the number of 4KB chunk to map. However, when Linux is using 64KB page granularity the array of pages (vma->vm_private_data) contain one page per 64KB. Fix it by incrementing st->index correctly. Furthermore, st->va is not correctly incremented as PAGE_SIZE != XEN_PAGE_SIZE. Fixes: 5995a68a ("xen/privcmd: Add support for Linux 64KB page granularity") Reported-by:
Feng Kan <fkan@apm.com> Signed-off-by:
Julien Grall <julien.grall@arm.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
-
Marc Gonzalez authored
commit 60cf0ce1 upstream. According to Boris, some user-space tools expect MTD drivers to update ecc_stats.corrected, and it's better to provide a lower bound than to provide no information at all. Fixes: 6956e238 ("mtd: nand: add tango NAND flash controller support") Reported-by:
Pavel Machek <pavel@ucw.cz> Signed-off-by:
Marc Gonzalez <marc_gonzalez@sigmadesigns.com> Signed-off-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by:
-
Andres Galacho authored
commit 2761b4f1 upstream. The device table is required to load modules based on modaliases. After adding MODULE_DEVICE_TABLE, below entries for example will be added to module.alias: alias: of:N*T*Csigma,smp8758-nandC* alias: of:N*T*Csigma,smp8758-nand Fixes: 6956e238 ("mtd: nand: add tango NAND flash controller support") Signed-off-by:
Andres Galacho <andresgalacho@gmail.com> Acked-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
Jan Kara authored
commit d8747d64 upstream. Commit b685d3d6 "block: treat REQ_FUA and REQ_PREFLUSH as synchronous" removed REQ_SYNC flag from WRITE_{FUA|PREFLUSH|...} definitions. generic_make_request_checks() however strips REQ_FUA and REQ_PREFLUSH flags from a bio when the storage doesn't report volatile write cache and thus write effectively becomes asynchronous which can lead to performance regressions Fix the problem by making sure all bios which are synchronous are properly marked with REQ_SYNC. Fixes: b685d3d6 CC: reiserfs-devel@vger.kernel.org Signed-off-by:
-
Hou Tao authored
commit 5be6b756 upstream. When adding a cfq_group into the cfq service tree, we use CFQ_IDLE_DELAY as the delay of cfq_group's vdisktime if there have been other cfq_groups already. When cfq is under iops mode, commit 9a7f38c4 ("cfq-iosched: Convert from jiffies to nanoseconds") could result in a large iops delay and lead to an abnormal io schedule delay for the added cfq_group. To fix it, we just need to revert to the old CFQ_IDLE_DELAY value: HZ / 5 when iops mode is enabled. Despite having the same value, the delay of a cfq_queue in idle class and the delay of cfq_group are different things, so I define two new macros for the delay of a cfq_group under time-slice mode and iops mode. Fixes: 9a7f38c4 ("cfq-iosched: Convert from jiffies to nanoseconds") Signed-off-by:
Hou Tao <houtao1@huawei.com> Acked-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Thomas Petazzoni authored
commit b2d3c270 upstream. The XORv2 engine on Armada 7K/8K can only access the first 40 bits of the physical address space, so the DMA mask must be set accordingly. Fixes: 19a340b1 ("dmaengine: mv_xor_v2: new driver") Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Thomas Petazzoni authored
commit 9dd4f319 upstream. The current implementation of interrupt coalescing doesn't work, because it doesn't configure the coalescing timer, which is needed to make sure we get an interrupt at some point. As a fix for stable, we simply remove the interrupt coalescing functionality. It will be re-introduced properly in a future commit. Fixes: 19a340b1 ("dmaengine: mv_xor_v2: new driver") Signed-off-by:
-
Thomas Petazzoni authored
commit 44d5887a upstream. The mv_xor_v2_tx_submit() gets the next available HW descriptor by calling mv_xor_v2_get_desq_write_ptr(), which reads a HW register telling the next available HW descriptor. This was working fine when HW descriptors were issued for processing directly in tx_submit(). However, as part of the review process of the driver, a change was requested to move the actual kick-off of HW descriptors processing to ->issue_pending(). Due to this, reading the HW register to know the next available HW descriptor no longer works. So instead of using this HW register, we implemented a software index pointing to the next available HW descriptor. Fixes: 19a340b1 ("dmaengine: mv_xor_v2: new driver") Signed-off-by:
-
Hanna Hawa authored
commit ab2c5f0a upstream. The engine was enabled prior to its configuration, which isn't correct. This patch relocates the activation of the XOR engine, to be after the configuration of the XOR engine. Fixes: 19a340b1 ("dmaengine: mv_xor_v2: new driver") Signed-off-by:
Hanna Hawa <hannah@marvell.com> Signed-off-by:
-
Thomas Petazzoni authored
commit bc473da1 upstream. Descriptors that have not been acknowledged by the async_tx layer should not be re-used, so this commit adjusts the implementation of mv_xor_v2_prep_sw_desc() to skip descriptors for which async_tx_test_ack() is false. Fixes: 19a340b1 ("dmaengine: mv_xor_v2: new driver") Signed-off-by:
-
Thomas Petazzoni authored
commit 2aab4e18 upstream. mv_xor_v2_tasklet() is looping over completed HW descriptors. Before the loop, it initializes 'next_pending_hw_desc' to the first HW descriptor to handle, and then the loop simply increments this point, without taking care of wrapping when we reach the last HW descriptor. The 'pending_ptr' index was being wrapped back to 0 at the end, but it wasn't used in each iteration of the loop to calculate next_pending_hw_desc. This commit fixes that, and makes next_pending_hw_desc a variable local to the loop itself. Fixes: 19a340b1 ("dmaengine: mv_xor_v2: new driver") Signed-off-by:
-
Thomas Petazzoni authored
commit eb8df543 upstream. The mv_xor_v2_prep_sw_desc() is called from a few different places in the driver, but we never take into account the fact that it might return NULL. This commit fixes that, ensuring that we don't panic if there are no more descriptors available. Fixes: 19a340b1 ("dmaengine: mv_xor_v2: new driver") Signed-off-by:
-
Alexander Sverdlin authored
commit 98f9de36 upstream. Draining the transfers in terminate_all callback happens with IRQs disabled, therefore induces huge latency: irqsoff latency trace v1.1.5 on 4.11.0 -------------------------------------------------------------------- latency: 39770 us, #57/57, CPU#0 | (M:preempt VP:0, KP:0, SP:0 HP:0) ----------------- | task: process-129 (uid:0 nice:0 policy:2 rt_prio:50) ----------------- => started at: _snd_pcm_stream_lock_irqsave => ended at: snd_pcm_stream_unlock_irqrestore _------=> CPU# / _-----=> irqs-off | / _----=> need-resched || / _---=> hardirq/softirq ||| / _--=> preempt-depth |||| / delay cmd pid ||||| time | caller \ / ||||| \ | / process-129 0d.s. 3us : _snd_pcm_stream_lock_irqsave process-129 0d.s1 9us : snd_pcm_stream_lock <-_snd_pcm_stream_lock_irqsave process-129 0d.s1 15us : preempt_count_add <-snd_pcm_stream_lock process-129 0d.s2 22us : preempt_count_add <-snd_pcm_stream_lock process-129 0d.s3 32us : snd_pcm_update_hw_ptr0 <-snd_pcm_period_elapsed process-129 0d.s3 41us : soc_pcm_pointer <-snd_pcm_update_hw_ptr0 process-129 0d.s3 50us : dmaengine_pcm_pointer <-soc_pcm_pointer process-129 0d.s3 58us+: snd_dmaengine_pcm_pointer_no_residue <-dmaengine_pcm_pointer process-129 0d.s3 96us : update_audio_tstamp <-snd_pcm_update_hw_ptr0 process-129 0d.s3 103us : snd_pcm_update_state <-snd_pcm_update_hw_ptr0 process-129 0d.s3 112us : xrun <-snd_pcm_update_state process-129 0d.s3 119us : snd_pcm_stop <-xrun process-129 0d.s3 126us : snd_pcm_action <-snd_pcm_stop process-129 0d.s3 134us : snd_pcm_action_single <-snd_pcm_action process-129 0d.s3 141us : snd_pcm_pre_stop <-snd_pcm_action_single process-129 0d.s3 150us : snd_pcm_do_stop <-snd_pcm_action_single process-129 0d.s3 157us : soc_pcm_trigger <-snd_pcm_do_stop process-129 0d.s3 166us : snd_dmaengine_pcm_trigger <-soc_pcm_trigger process-129 0d.s3 175us : ep93xx_dma_terminate_all <-snd_dmaengine_pcm_trigger process-129 0d.s3 182us : preempt_count_add <-ep93xx_dma_terminate_all process-129 0d.s4 189us*: m2p_hw_shutdown <-ep93xx_dma_terminate_all process-129 0d.s4 39472us : m2p_hw_setup <-ep93xx_dma_terminate_all ... rest skipped... process-129 0d.s. 40080us : <stack trace> => ep93xx_dma_tasklet => tasklet_action => __do_softirq => irq_exit => __handle_domain_irq => vic_handle_irq => __irq_usr => 0xb66c6668 Just abort the transfers and warn if the HW state is not what we expect. Move draining into device_synchronize callback. Signed-off-by:
Alexander Sverdlin <alexander.sverdlin@gmail.com> Signed-off-by:
-
Alexander Sverdlin authored
commit 0037ae47 upstream. The current buffer is being reset to zero on device_free_chan_resources() but not on device_terminate_all(). It could happen that HW is restarted and expects BASE0 to be used, but the driver is not synchronized and will start from BASE1. One solution is to reset the buffer explicitly in m2p_hw_setup(). Signed-off-by:
-
Hiroyuki Yokoyama authored
commit 9a445bbb upstream. This patch fixes the register definition of AE (Address Error flag) bit. Fixes: 0c1c8ff3 ("dmaengine: usb-dmac: Add Renesas USB DMA Controller (USB-DMAC) driver") Signed-off-by:
Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com> [Shimoda: add Fixes and Cc tags in the commit log] Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
-
Wanpeng Li authored
commit 9bc1f09f upstream. INFO: task gnome-terminal-:1734 blocked for more than 120 seconds. Not tainted 4.12.0-rc4+ #8 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. gnome-terminal- D 0 1734 1015 0x00000000 Call Trace: __schedule+0x3cd/0xb30 schedule+0x40/0x90 kvm_async_pf_task_wait+0x1cc/0x270 ? __vfs_read+0x37/0x150 ? prepare_to_swait+0x22/0x70 do_async_page_fault+0x77/0xb0 ? do_async_page_fault+0x77/0xb0 async_page_fault+0x28/0x30 This is triggered by running both win7 and win2016 on L1 KVM simultaneously, and then gives stress to memory on L1, I can observed this hang on L1 when at least ~70% swap area is occupied on L0. This is due to async pf was injected to L2 which should be injected to L1, L2 guest starts receiving pagefault w/ bogus %cr2(apf token from the host actually), and L1 guest starts accumulating tasks stuck in D state in kvm_async_pf_task_wait() since missing PAGE_READY async_pfs. This patch fixes the hang by doing async pf when executing L1 guest. Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
Wanpeng Li <wanpeng.li@hotmail.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Marc Zyngier authored
commit 33b5c388 upstream. We currently have the HSCTLR.A bit set, trapping unaligned accesses at HYP, but we're not really prepared to deal with it. Since the rest of the kernel is pretty happy about that, let's follow its example and set HSCTLR.A to zero. Modern CPUs don't really care. Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
Christoffer Dall <cdall@linaro.org> Signed-off-by:
-
Marc Zyngier authored
commit 78fd6dcf upstream. We currently have the SCTLR_EL2.A bit set, trapping unaligned accesses at EL2, but we're not really prepared to deal with it. So far, this has been unnoticed, until GCC 7 started emitting those (in particular 64bit writes on a 32bit boundary). Since the rest of the kernel is pretty happy about that, let's follow its example and set SCTLR_EL2.A to zero. Modern CPUs don't really care. Reported-by:
Alexander Graf <agraf@suse.de> Signed-off-by:
-
Marc Zyngier authored
commit d68c1f7f upstream. __do_hyp_init has the rather bad habit of ignoring RES1 bits and writing them back as zero. On a v8.0-8.2 CPU, this doesn't do anything bad, but may end-up being pretty nasty on future revisions of the architecture. Let's preserve those bits so that we don't have to fix this later on. Signed-off-by:
-
Wanpeng Li authored
commit a3641631 upstream. If "i" is the last element in the vcpu->arch.cpuid_entries[] array, it potentially can be exploited the vulnerability. this will out-of-bounds read and write. Luckily, the effect is small: /* when no next entry is found, the current entry[i] is reselected */ for (j = i + 1; ; j = (j + 1) % nent) { struct kvm_cpuid_entry2 *ej = &vcpu->arch.cpuid_entries[j]; if (ej->function == e->function) { It reads ej->maxphyaddr, which is user controlled. However... ej->flags |= KVM_CPUID_FLAG_STATE_READ_NEXT; After cpuid_entries there is int maxphyaddr; struct x86_emulate_ctxt emulate_ctxt; /* 16-byte aligned */ So we have: - cpuid_entries at offset 1B50 (6992) - maxphyaddr at offset 27D0 (6992 + 3200 = 10192) - padding at 27D4...27DF - emulate_ctxt at 27E0 And it writes in the padding. Pfew, writing the ops field of emulate_ctxt would have been much worse. This patch fixes it by modding the index to avoid the out-of-bounds access. Worst case, i == j and ej->function == e->function, the loop can bail out. Reported-by:
Moguofang <moguofang@huawei.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Guofang Mo <moguofang@huawei.com> Signed-off-by:
-
Paolo Bonzini authored
commit bbaf0e2b upstream. native_safe_halt enables interrupts, and you just shouldn't call rcu_irq_enter() with interrupts enabled. Reorder the call with the following local_irq_disable() to respect the invariant. Reported-by:
Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Tested-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Dave Young authored
commit 7425826f upstream. Sabrina Dubroca reported an early panic: BUG: unable to handle kernel paging request at ffffffffff240001 IP: efi_bgrt_init+0xdc/0x134 [...] ---[ end Kernel panic - not syncing: Attempted to kill the idle task! ... which was introduced by: 7b0a9114 ("efi/x86: Move the EFI BGRT init code to early init code") The cause is that on this machine the firmware provides the EFI ACPI BGRT table even on legacy non-EFI bootups - which table should be EFI only. The garbage BGRT data causes the efi_bgrt_init() panic. Add a check to skip efi_bgrt_init() in case non-EFI bootup to work around this firmware bug. Tested-by:
Sabrina Dubroca <sd@queasysnail.net> Signed-off-by:
Dave Young <dyoung@redhat.com> Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Matt Fleming <matt@codeblueprint.co.uk> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Fixes: 7b0a9114 ("efi/x86: Move the EFI BGRT init code to early init code") Link: http://lkml.kernel.org/r/20170526113652.21339-6-matt@codeblueprint.co.uk [ Rewrote the changelog to be more readable. ] Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Juergen Gross authored
commit 1ea34adb upstream. When booted as Xen dom0 there won't be an EFI memmap allocated. Avoid issuing an error message in this case: [ 0.144079] efi: Failed to allocate new EFI memmap Signed-off-by:
-
Jan Kara authored
commit 0f0b9b63 upstream. Commit b685d3d6 "block: treat REQ_FUA and REQ_PREFLUSH as synchronous" removed REQ_SYNC flag from WRITE_{FUA|PREFLUSH|...} definitions. generic_make_request_checks() however strips REQ_FUA and REQ_PREFLUSH flags from a bio when the storage doesn't report volatile write cache and thus write effectively becomes asynchronous which can lead to performance regressions Fix the problem by making sure all bios which are synchronous are properly marked with REQ_SYNC. Fixes: b685d3d6 CC: Steven Whitehouse <swhiteho@redhat.com> CC: cluster-devel@redhat.com Acked-by:
Bob Peterson <rpeterso@redhat.com> Signed-off-by:
-
J. Bruce Fields authored
commit 9a307403 upstream. if we receive a compound such that: - the sessionid, slot, and sequence number in the SEQUENCE op match a cached succesful reply with N ops, and - the Nth operation of the compound is a PUTFH, PUTPUBFH, PUTROOTFH, or RESTOREFH, then nfsd4_sequence will return 0 and set cstate->status to nfserr_replay_cache. The current filehandle will not be set. This will cause us to call check_nfsd_access with first argument NULL. To nfsd4_compound it looks like we just succesfully executed an operation that set a filehandle, but the current filehandle is not set. Fix this by moving the nfserr_replay_cache earlier. There was never any reason to have it after the encode_op label, since the only case where he hit that is when opdesc->op_func sets it. Note that there are two ways we could hit this case: - a client is resending a previously sent compound that ended with one of the four PUTFH-like operations, or - a client is sending a *new* compound that (incorrectly) shares sessionid, slot, and sequence number with a previously sent compound, and the length of the previously sent compound happens to match the position of a PUTFH-like operation in the new compound. The second is obviously incorrect client behavior. The first is also very strange--the only purpose of a PUTFH-like operation is to set the current filehandle to be used by the following operation, so there's no point in having it as the last in a compound. So it's likely this requires a buggy or malicious client to reproduce. Reported-by:
Scott Mayhew <smayhew@redhat.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Alex Deucher authored
commit 0a646f33 upstream. Even if the vblank period would allow it, it still seems to be problematic on some cards. v2: fix logic inversion (Nils) bug: https://bugs.freedesktop.org/show_bug.cgi?id=96868Acked-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Vegard Nossum authored
commit 4d6501dc upstream. If a kthread forks (e.g. usermodehelper since commit 1da5c46f) but fails in copy_process() between calling dup_task_struct() and setting p->set_child_tid, then the value of p->set_child_tid will be inherited from the parent and get prematurely freed by free_kthread_struct(). kthread() - worker_thread() - process_one_work() | - call_usermodehelper_exec_work() | - kernel_thread() | - _do_fork() | - copy_process() | - dup_task_struct() | - arch_dup_task_struct() | - tsk->set_child_tid = current->set_child_tid // implied | - ... | - goto bad_fork_* | - ... | - free_task(tsk) | - free_kthread_struct(tsk) | - kfree(tsk->set_child_tid) - ... - schedule() - __schedule() - wq_worker_sleeping() - kthread_data(task)->flags // UAF The problem started showing up with commit 1da5c46f since it reused ->set_child_tid for the kthread worker data. A better long-term solution might be to get rid of the ->set_child_tid abuse. The comment in set_kthread_struct() also looks slightly wrong. Debugged-by:
Jamie Iles <jamie.iles@oracle.com> Fixes: 1da5c46f ("kthread: Make struct kthread kmalloc'ed") Signed-off-by:
Vegard Nossum <vegard.nossum@oracle.com> Acked-by:
Oleg Nesterov <oleg@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jamie Iles <jamie.iles@oracle.com> Link: http://lkml.kernel.org/r/20170509073959.17858-1-vegard.nossum@oracle.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Amir Goldstein authored
commit 8137ae26 upstream. Fixes: 42f269b9 ("ovl: rearrange code in ovl_copy_up_locked()") Signed-off-by:
Amir Goldstein <amir73il@gmail.com> Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
Gilad Ben-Yossef authored
commit f3ad5870 upstream. crypto_gcm_setkey() was using wait_for_completion_interruptible() to wait for completion of async crypto op but if a signal occurs it may return before DMA ops of HW crypto provider finish, thus corrupting the data buffer that is kfree'ed in this case. Resolve this by using wait_for_completion() instead. Reported-by:
Eric Biggers <ebiggers3@gmail.com> Signed-off-by:
Gilad Ben-Yossef <gilad@benyossef.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Gilad Ben-Yossef authored
commit a5dfefb1 upstream. drbg_kcapi_sym_ctr() was using wait_for_completion_interruptible() to wait for completion of async crypto op but if a signal occurs it may return before DMA ops of HW crypto provider finish, thus corrupting the output buffer. Resolve this by using wait_for_completion() instead. Reported-by:
-
Eric Biggers authored
commit e9ff56ac upstream. Since v4.9, the crypto API cannot (normally) be used to encrypt/decrypt stack buffers because the stack may be virtually mapped. Fix this for the padding buffers in encrypted-keys by using ZERO_PAGE for the encryption padding and by allocating a temporary heap buffer for the decryption padding. Tested with CONFIG_DEBUG_SG=y: keyctl new_session keyctl add user master "abcdefghijklmnop" @s keyid=$(keyctl add encrypted desc "new user:master 25" @s) datablob="$(keyctl pipe $keyid)" keyctl unlink $keyid keyid=$(keyctl add encrypted desc "load $datablob" @s) datablob2="$(keyctl pipe $keyid)" [ "$datablob" = "$datablob2" ] && echo "Success!" Cc: Andy Lutomirski <luto@kernel.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Mimi Zohar <zohar@linux.vnet.ibm.com> Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
James Morris <james.l.morris@oracle.com> Signed-off-by:
-
Eric Biggers authored
commit 63a0b050 upstream. key_update() freed the key_preparsed_payload even if it was not initialized first. This would cause a crash if userspace called keyctl_update() on a key with type like "asymmetric" that has a ->preparse() method but not an ->update() method. Possibly it could even be triggered for other key types by racing with keyctl_setperm() to make the KEY_NEED_WRITE check fail (the permission was already checked, so normally it wouldn't fail there). Reproducer with key type "asymmetric", given a valid cert.der: keyctl new_session keyid=$(keyctl padd asymmetric desc @s < cert.der) keyctl setperm $keyid 0x3f000000 keyctl update $keyid data [ 150.686666] BUG: unable to handle kernel NULL pointer dereference at 0000000000000001 [ 150.687601] IP: asymmetric_key_free_kids+0x12/0x30 [ 150.688139] PGD 38a3d067 [ 150.688141] PUD 3b3de067 [ 150.688447] PMD 0 [ 150.688745] [ 150.689160] Oops: 0000 [#1] SMP [ 150.689455] Modules linked in: [ 150.689769] CPU: 1 PID: 2478 Comm: keyctl Not tainted 4.11.0-rc4-xfstests-00187-ga9f6b6b8 #742 [ 150.690916] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-20170228_101828-anatol 04/01/2014 [ 150.692199] task: ffff88003b30c480 task.stack: ffffc90000350000 [ 150.692952] RIP: 0010:asymmetric_key_free_kids+0x12/0x30 [ 150.693556] RSP: 0018:ffffc90000353e58 EFLAGS: 00010202 [ 150.694142] RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000004 [ 150.694845] RDX: ffffffff81ee3920 RSI: ffff88003d4b0700 RDI: 0000000000000001 [ 150.697569] RBP: ffffc90000353e60 R08: ffff88003d5d2140 R09: 0000000000000000 [ 150.702483] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000001 [ 150.707393] R13: 0000000000000004 R14: ffff880038a4d2d8 R15: 000000000040411f [ 150.709720] FS: 00007fcbcee35700(0000) GS:ffff88003fd00000(0000) knlGS:0000000000000000 [ 150.711504] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 150.712733] CR2: 0000000000000001 CR3: 0000000039eab000 CR4: 00000000003406e0 [ 150.714487] Call Trace: [ 150.714975] asymmetric_key_free_preparse+0x2f/0x40 [ 150.715907] key_update+0xf7/0x140 [ 150.716560] ? key_default_cmp+0x20/0x20 [ 150.717319] keyctl_update_key+0xb0/0xe0 [ 150.718066] SyS_keyctl+0x109/0x130 [ 150.718663] entry_SYSCALL_64_fastpath+0x1f/0xc2 [ 150.719440] RIP: 0033:0x7fcbce75ff19 [ 150.719926] RSP: 002b:00007ffd5d167088 EFLAGS: 00000206 ORIG_RAX: 00000000000000fa [ 150.720918] RAX: ffffffffffffffda RBX: 0000000000404d80 RCX: 00007fcbce75ff19 [ 150.721874] RDX: 00007ffd5d16785e RSI: 000000002866cd36 RDI: 0000000000000002 [ 150.722827] RBP: 0000000000000006 R08: 000000002866cd36 R09: 00007ffd5d16785e [ 150.723781] R10: 0000000000000004 R11: 0000000000000206 R12: 0000000000404d80 [ 150.724650] R13: 00007ffd5d16784d R14: 00007ffd5d167238 R15: 000000000040411f [ 150.725447] Code: 83 c4 08 31 c0 5b 41 5c 41 5d 41 5e 41 5f 5d c3 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 85 ff 74 23 55 48 89 e5 53 48 89 fb <48> 8b 3f e8 06 21 c5 ff 48 8b 7b 08 e8 fd 20 c5 ff 48 89 df e8 [ 150.727489] RIP: asymmetric_key_free_kids+0x12/0x30 RSP: ffffc90000353e58 [ 150.728117] CR2: 0000000000000001 [ 150.728430] ---[ end trace f7f8fe1da2d5ae8d ]--- Fixes: 4d8c0250 ("KEYS: Call ->free_preparse() even after ->preparse() returns an error") Signed-off-by:
-
Eric Biggers authored
commit 5649645d upstream. sys_add_key() and the KEYCTL_UPDATE operation of sys_keyctl() allowed a NULL payload with nonzero length to be passed to the key type's ->preparse(), ->instantiate(), and/or ->update() methods. Various key types including asymmetric, cifs.idmap, cifs.spnego, and pkcs7_test did not handle this case, allowing an unprivileged user to trivially cause a NULL pointer dereference (kernel oops) if one of these key types was present. Fix it by doing the copy_from_user() when 'plen' is nonzero rather than when '_payload' is non-NULL, causing the syscall to fail with EFAULT as expected when an invalid buffer is specified. Signed-off-by:
-
Gilad Ben-Yossef authored
commit e68368ae upstream. public_key_verify_signature() was passing the CRYPTO_TFM_REQ_MAY_BACKLOG flag to akcipher_request_set_callback() but was not handling correctly the case where a -EBUSY error could be returned from the call to crypto_akcipher_verify() if backlog was used, possibly casuing data corruption due to use-after-free of buffers. Resolve this by handling -EBUSY correctly. Signed-off-by:
-
Murali Karicheri authored
commit 791229f1 upstream. Ethernet networking on K2L has been broken since v4.11-rc1. This was caused by commit 32a34441 ("ARM: keystone: dts: fix netcp clocks and add names"). This commit inadvertently moves on-chip static RAM clock to the end of list of clocks provided for netcp. Since keystone PM domain support does not have a list of recognized con_ids, only the first clock in the list comes under runtime PM management. This means the OSR (On-chip Static RAM) clock remains disabled and that broke networking on K2L. The OSR is used by QMSS on K2L as an external linking RAM. However this is a standalone RAM that can be used for non-QMSS usage (as well as from DSP side). So add a SRAM device node for the same and add the OSR clock to the node. Remove the now redundant OSR clock node from netcp. To manage all clocks defined for netCP's use by runtime PM needs keystone generic power domain (genpd) driver support which is under works. Meanwhile, this patch restores K2L networking and is correct irrespective of any future genpd work since OSR is an independent module and not part of NetCP anyway. Signed-off-by:
Murali Karicheri <m-karicheri2@ti.com> Acked-by:
Tero Kristo <t-kristo@ti.com> [nsekhar@ti.com: commit message updates, port to latest mainline] Signed-off-by:
Sekhar Nori <nsekhar@ti.com> Acked-by:
Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
