- 09 Jun, 2015 13 commits
-
-
Vladimir Kondratiev authored
Need to reorder init sequence to run wil_platform_init before pci_enable_device. Assumption is platform init may be required before device may be enabled. Another issue, platform uninit should be called after pci_disable_device because platform uninit may render pci device non-accessible. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Vladimir Kondratiev authored
Provide platform hooks for module init/exit. If platform require to perform some specific actions in global context, this is where to do so. Example may be turning on power for the PCIE based on DT information. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Hamad Kadmany authored
Pass hidden SSID information to FW for proper operation. In order to be able to scan/connect to the hidden SSID, SSID setting is added when scan is requested from FW. SSID scanning currently supports single SSID due to FW limitation. Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com> Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Vladimir Kondratiev authored
Provide detailed statistics for the Rx frames per MCS Statistics printed in "stations" debugfs entry Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Vladimir Kondratiev authored
Firmware defines new memory region, mac_rgf_ext that need to be accessed from the host for debug purposes. Add corresponded mapping Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Vladimir Kondratiev authored
Control Bcast ring size in similar way as Rx and Tx ones, through "bcast_ring_order" modparam, actual ring size is 1 << order Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Brent Taylor authored
When one client is associated and connected to an ar6003 hw version 2.0 with firmware 3.1.1.149, and another client tries to connect, the first client's MAC address is lost in the station list because the "aid" is always "1". The structure "wmi_connect_event" has the "aid" as the second byte in the message, but it should be the first byte. This patch has been tested with linux-3.10.40 Signed-off-by: Brent Taylor <motobud@gmail.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Michal Kazior authored
Found during code review. This was pretty much impossible to happen but better safe than sorry. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Michal Kazior authored
In the midst of chanctx patch review channel switching became broken which I failed to notice until now. Function ath10k_mac_vif_chan() reports current chandef which isn't updated until after switch_vif_chanctx() is returned from. Consequently the driver just restarted operation on channels it was residing already instead of switching to the new ones. Fixes: 500ff9f9 ("ath10k: implement chanctx API") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Michal Kazior authored
In practice there's no point in having a copy of chanctx_conf. Most of the time the channel pointer (and band along with it) is accessed and this can't change after a chanctx is created because switching is done using explicit chanctx swapping via switch_vif_chanctx(). The only thing that can change within a chanctx_conf and is used by the driver is radar_enabled and channel width. These are however always accessed in adequate mac80211 callback context which guarantees safe access to the chanctx data. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Michal Kazior authored
Channel contexts aren't iterable until after they've been added to the driver. The code assumed otherwise. This problem could result in: * rx_channel being NULL and forcing Rx path to go the slow way to get channel on QCA988X, * report incorrect channel when running multi-channel on QCA61X4 hw2.1, * report incorrect channel after AP channel switch. Fixes: 500ff9f9 ("ath10k: implement chanctx API") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Raja Mani authored
mete_data is extracted from ce descriptor and stored in variable 'id'. later, id is not used anywhere in the same function. Fixes: d84a512d ("ath10k: remove transfer_id from ath10k_hif_cb::tx_completion") Signed-off-by: Raja Mani <rmani@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Raja Mani authored
When wmi mgmt event function fails to parse given skb, it should be freed on failure condition to avoid memory leaks. Found this during the code review. Signed-off-by: Raja Mani <rmani@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
- 01 Jun, 2015 2 commits
-
-
Michal Kazior authored
If probing failed pci sleep timer could remain running and trigger after ath10k structures were freed causing invalid pointer dereference: BUG: unable to handle kernel paging request at ffffc90001c80004 IP: [<ffffffff81354728>] iowrite32+0x38/0x40 ... Call Trace: <IRQ> [<ffffffffa00da048>] ? __ath10k_pci_sleep+0x48/0x60 [ath10k_pci] [<ffffffffa00da44e>] ath10k_pci_ps_timer+0x5e/0x80 [ath10k_pci] [<ffffffff810b210e>] call_timer_fn+0x3e/0x120 [<ffffffffa00da3f0>] ? ath10k_pci_wake+0x150/0x150 [ath10k_pci] [<ffffffff810b3d11>] run_timer_softirq+0x201/0x2e0 [<ffffffff8105d73f>] __do_softirq+0xaf/0x290 [<ffffffff8105da95>] irq_exit+0x95/0xa0 [<ffffffff81950406>] smp_apic_timer_interrupt+0x46/0x60 [<ffffffff8194e77e>] apic_timer_interrupt+0x6e/0x80 Fixes: 77258d40 ("ath10k: enable pci soc powersaving") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Rajkumar Manoharan authored
Some of of qca988x solutions are having global reset issue during target initialization. Bypassing PLL setting before downloading firmware and letting the SoC run on REF_CLK is fixing the problem. Corresponding firmware change is also needed to set the clock source once the target is initialized. Since 10.2.4 firmware is having this ROM patch, applying skip_clock_init only for 10.2.4 firmware versions. Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
- 29 May, 2015 4 commits
-
-
Michal Kazior authored
This could lead userspace initram images getting built without necessary firmware files included leading to probing failures of ath10k on boot with QCA61X4. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Michal Kazior authored
In some cases some channel survey data was reported incorrect. Channel info events were expected to come in pairs without and with COMPLETE flag set respectively for each channel visit during scan. The known deviation from this is rule for last scan chan info and first (next) scan chan info both have COMPLETE flag set. This was either programmed with the intent of providing BSS cycle count info or this is an artefact of firmware scan state machine. Either way this is useless due to short wraparound time, wraparound quirks and no overflow notification. Survey dumps now include only data gathered during scan channel visits that can be computed correctly. This should improve hostapd ACS a little bit. Reported-by: Srinivasa Duvvuri <sduvvuri@chromium.org> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Michal Kazior authored
When QCA988X cycle counter HW register wraps around it resets to 0x7fffffff instead of 0. All other cycle counter related registers are divided by 2 so they never wraparound themselves. QCA61X4 has a uniform CC and it wraparounds in a regular fashion though. Worst case wraparound time is approx 24 seconds (2**31 / 88MHz). Since scan channel visit times are max 5 seconds (offchannel case) it is guaranteed there's been at most 1 wraparound and it is possible to compute survey active time value. It is, however, impossible to determine the point at which Rx Clear Count has been divided by two so it is not reported upon wraparound. This fixes some occasional incorrect survey data on QCA988X as some channels (depending on how/when scan/offchannel requests were requested) would have approx 24 sec active time which wasn't actually the case. This should improve hostapd ACS a little bit. Reported-by: Srinivasa Duvvuri <sduvvuri@chromium.org> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Michal Kazior authored
The macro isn't WMI specific. Instead it is related to hardware chip so move the macro accordingly. While at it document the magic value. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
- 25 May, 2015 21 commits
-
-
Kalle Valo authored
Major changes: ath10k: * qca6174 power consumption improvements, enable ASPM etc (Michal) wil6210: * support Wi-Fi Simple Configuration in STA mode
-
Hariprasad Shenai authored
Add support for flashing 10GBaseT adapter with BCM 84834 PHY and Aquantia AQ1202 PHY. Updating of the PHY firmware must happen before the INITIALIZE_CMD. Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Daniel Borkmann authored
Add two more eBPF test cases for JITs, i.e. the second one revealed a bug in the x86_64 JIT compiler, where only an int3 filled image from the allocator was emitted and later wrongly set by the compiler as the bpf_func program code since optimization pass boundary was surpassed w/o actually emitting opcodes. Interpreter: [ 45.782892] test_bpf: #242 BPF_MAXINSNS: Very long jump backwards jited:0 11 PASS [ 45.783062] test_bpf: #243 BPF_MAXINSNS: Edge hopping nuthouse jited:0 14705 PASS After x86_64 JIT (fixed): [ 80.495638] test_bpf: #242 BPF_MAXINSNS: Very long jump backwards jited:1 6 PASS [ 80.495957] test_bpf: #243 BPF_MAXINSNS: Edge hopping nuthouse jited:1 17157 PASS Reference: http://thread.gmane.org/gmane.linux.network/364729Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Tom Lendacky says: ==================== amd-xgbe: AMD XGBE driver updates 2015-05-22 The following patches are included in this driver update series: - Retrieve and set an additional hardware feature setting - Fix the initial mode/speed determination when auto-negotiation is disabled - Add additional netif_dbg support to the driver This patch series is based on net-next. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
Change more netdev_dbg statements over to netif_dbg and add some new netif_dbg statements to the driver. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
When the ethtool command is used to set the speed of the device while the device is down, the check to set the initial mode may fail when the device is brought up, causing failure to bring the device up. Update the code to set the initial mode based on the desired speed if auto-negotiation is disabled. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
The device private data structure contains all the defined hardware features for the device. However one of the features is not set. Even though the feature is not currently used, set it to avoid future issues of the feature being checked thinking it has been properly set. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Florian Westphal authored
Send icmp pmtu error if we find that the largest fragment of df-skb exceeded the output path mtu. The ip output path will still catch this later on but we can avoid the forward/postrouting hook traversal by rejecting right away. This is what ipv6 already does. Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Hannes Frederic Sowa says: ==================== net: af_unix: zerocopy stream bits This series implements zerocopy support for AF_UNIX SOCK_STREAM sockets. Changelog in the specific patches. Thanks to all the reviewers! ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Hannes Frederic Sowa authored
unix_stream_recvmsg is refactored to unix_stream_read_generic in this patch and enhanced to deal with pipe splicing. The refactoring is inneglible, we mostly have to deal with a non-existing struct msghdr argument. Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Hannes Frederic Sowa authored
Prepare skb_splice_bits to be able to deal with AF_UNIX sockets. AF_UNIX sockets don't use lock_sock/release_sock and thus we have to use a callback to make the locking and unlocking configureable. Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Hannes Frederic Sowa authored
This patch implements sendpage support for AF_UNIX SOCK_STREAM sockets. This is also required for a complete splice implementation. The implementation is a bit tricky because we append to already existing skbs and so have to hold unix_sk->readlock to protect the reading side from either advancing UNIXCB.consumed or freeing the skb at the socket receive tail. Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Hannes Frederic Sowa authored
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Merge tag 'wireless-drivers-next-for-davem-2015-05-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== ath10k: * enable channel 144 on 5 GHz * enable Adaptive Noise Immunity (ANI) by default * add Wake on Wireless LAN (WOW) patterns support * add basic Tunneled Direct Link Setup (TDLS) support * add multi-channel support for QCA6174 * enable IBSS RSN support * enable Bluetooth Coexistance whenever firmware supports it * add more versatile way to set bitrates used by the firmware ath9k: * spectral scan: add support for multiple FFT frames per report iwlwifi: * major rework of the scan code (Luca) * some work on the thermal code (Chaya Rachel) * some work on the firwmare debugging infrastructure brcmfmac: * SDIO suspend and resume fixes * wiphy band info and changes in regulatory settings * add support for BCM4324 SDIO and BCM4358 PCIe * enable support of PCIe devices on router platforms (Hante) ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Or Gerlitz says: ==================== mlx4: Enable single ported VFs over IB ports This series further enhances the support for mlx4 single ported VFs introduced in 3.15 to work over IB ports too. Just as quick reminder, the ConnectX3 device family exposes one PCI device which serves both ports. This can be non-optimal under virtualization schemes where the admin would like the VF to expose one interface to the VM, etc. Since all the VF interaction with the firmware passes through the PF driver, we can emulate to the VF they have one port, and further create a set of the VFs which act on port1 of the device and another set which acts on port2. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Or Gerlitz authored
Remove the limitation that disallows configuring single ported VFs in the presence of IB ports, after addressing the issues that prevented that to work. SMI (QP0) requests/responses are still not supported for single ported IB VFs. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Or Gerlitz authored
It's legal for drivers to provide the QP port through the QPC schedule-queue field on the reset-to-init QP state change. Add adjusting of the schedule queue port in the SRIOV wrapper for that operation too. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Or Gerlitz authored
Some VF drivers flow set the schedule queue in the QP context but without setting none of OPTPAR_SCHED_QUEUE or OPTPAR_PRIMARY_ADDR_PATH. To allow for such non-modified drivers to function as single ported IB VFs, we must adjust the schedule queue port whenever being set, e.g as currently done for single ported Eth VFs. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Or Gerlitz authored
As part of enabling single ported VFs over IB ports we need to handle some of the flows for generting EQ events for VFs which don't come into play under Eth ports. This mainly includes port management events derived from changes of the phyiscal port (lid change, client re-register, down/up, etc), VF pkey table changes and VF guid changes initiated by the IB driver. (1) make sure that events are generated only for VFs sitting on the relevant physical port (under the ALL_SLAVES flow). (2) before generating the event, convert from physical (one or two) to VF port (always equals one). Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Or Gerlitz authored
When multiplexling a MAD sent from VF, we should convert the port used by the guest to send the packet to the actual physical port which will be used to transmit the packet, before building the relevant address-handle (AH). This is needed under VPI for single ported VFs, since the code that builds the AH (mlx4_ib_query_ah()) makes decisions based on the input port. If we use the port number provided by the guest, it might have different protocol vs. the one this packat has to go from, and hence the result could be wrong. So far, the conversion was done after the AH was built and it worked for single ported Eth VFs which were not enabled under VPI. When adding support for single ported IB VFs and VPI, we hit that. Fixes: 449fc488 ('net/mlx4: Adapt code for N-Port VF') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Or Gerlitz authored
Single port VFs always provide port = 1 (even if the actual physical port used is port 2). As such, we need to convert the port provided by the VF to the physical port before calling into the firmware. It turns out that the Linux mlx4 VF RoCE driver maintains a copy of the GID table and hence this change became critical only for single ported IB VFs, but it could be needed for other RoCE VF drivers too. Fixes: 449fc488 ('net/mlx4: Adapt code for N-Port VF') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
-