This is the first set of omap cleanup patches for v3.8 merge
window to remove most of the remaining plat includes to get us
closer to ARM common zImage support.

To avoid a huge amount of trivial merge conflicts with includes,
this branch is based on several small topic branches coordinated
with the driver subsystem maintainers. These branches are based on
v3.7-rc1 and can also be merged into the related driver subsystem
branches as needed:

omap-for-v3.8/cleanup-headers-prepare   few trivial driver changes
omap-for-v3.8/cleanup-headers-dma       move of the DMA header
omap-for-v3.8/cleanup-headers-gpmc      GPMC and MTD changes
omap-for-v3.8/cleanup-headers-mmc       MMC related changes
omap-for-v3.8/cleanup-headers-dss       DSS related changes
omap-for-v3.8/cleanup-headers-asoc      ASoC related changes

Note that for the dma-omap.h, it was decided that it should be
is completed. For the related discussion, please see:

https://patchwork.kernel.org/patch/1519591/#

After these patches we still have a few plat headers remaining
that will be handled in later pull requests.

This allows us to get rid of the ifdefs in 8250.c.

Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Modify divisor to select the nearest baud rate divider rather than the
lowest. It minimizes baud rate errors especially on low UART clock
frequencies.

For example, if uartclk is 33000000 and baud is 115200 the ratio is
about 17.9 The current code selects 17 (5% error) but should select 18
(0.5% error).

This 5% error in baud rate leads to garbage on receiving end, while 0.5%
doesn't.

The issue showed up when using the stock 8250 driver for
Synopsys DW UART. This was on a FPGA with ~12MHz UART clock.
When we enabled early serial, we saw garbage which was narrowed down
to the rounding error.

So the bug had been latent and it only showed up with such low clock rates.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When a driver has the low_latency flag set and uses the schedule_flip()
function to initiate copying data to the line discipline, a workqueue is
scheduled in but never actually flushed. This is incorrect use of the
low_latency flag (driver should not support the low_latency flag, or use
the tty_flip_buffer_push() function instead). Make sure a warning is
reported to catch incorrect use of the low_latency flag.

This patch goes with: cee4ad1eSigned-off-by: Ivo Sieben <meltedpianoman@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Instead of BUG_ON(in_interrupt()), since that doesn't check for all
the newfangled stuff like preempt.

Note that this is valid since the console_sem is essentially used like
a real mutex with only two twists:
- we allow trylock from hardirq context
- across suspend/resume we lock the logical console_lock, but drop the
  semaphore protecting the locking state.

Now that doesn't guarantee that no one is playing tricks in
single-thread atomic contexts at suspend/resume/boot time, but
- I couldn't find anything suspicious with some grepping,
- might_sleep shouldn't die,
- and I think the upside of catching more potential issues is worth
  the risk of getting a might_sleep backtrace that would have been
  save (and then dealing with that fallout).

Cc: Dave Airlie <airlied@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

So this is it. The big step why we did all the work over the past
kernel releases. Now everything is prepared, so nothing protects us
from doing that big step.

           |  |            \  \ nnnn/^l      |  |
           |  |             \  /     /       |  |
           |  '-,.__   =>    \/   ,-`    =>  |  '-,.__
           | O __.´´)        (  .`           | O __.´´)
            ~~~   ~~          ``              ~~~   ~~
The buffers are now in the tty_port structure and we can start
teaching the buffer helpers (insert char/string, flip etc.) to use
tty_port instead of tty_struct all around.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For that purpose we have to temporarily introduce a second tty back
pointer into tty_port. It is because serial layer, and maybe others,
still do not use tty_port_tty_set/get. So that we cannot set the
tty_port->tty to NULL at will now.

Yes, the fix would be to convert whole serial layer and all its users
to tty_port_tty_set/get. However we are in the process of removing the
need of tty in most of the call sites, so this would lead to a
duplicated work.

Instead we have now tty_port->itty (internal tty) which will be used
only in flush_to_ldisc. For that one it is ensured that itty is valid
wherever the work is run. IOW, the work is synchronously cancelled
before we set itty to NULL and also before hangup is processed.

After we need only tty_port and not tty_struct in most code, this
shall be changed to tty_port_tty_set/get and itty removed completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

During the move of tty buffers from tty_struct to tty_port, we will
need to switch all users of buf to tty->port->buf. There are many
functions where this is accessed directly in their code many times.
Cache the tty->buf pointer in such functions now and change only
single lines in each function in the next patch.

Not that it is convenient for the next patch, but the code is now also
more readable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

They are only TTY buffers specific. And the buffers will go to
tty_port in the next patches. So to remove the need to have both
tty_port and tty_struct at some places, let us move the flags to
tty_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In some funtions we need only n_tty_data, so pass it down directly in
case tty is not needed there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

atomic_write_lock is not n_tty specific, so move it up in the
tty_struct.

And since these are the last ones to move, remove also the comment
saying there are some ldisc' members. There are none now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

All the ring-buffers...
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Here we move bitmaps and use DECLARE_BITMAP to declare them in the new
structure. And instead of memset, we use bitmap_zero as it is more
appropriate.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Here we start moving all the n_tty related bits from tty_struct to
the newly defined n_tty_data struct in n_tty proper.

In this patch primitive members and bits are moved. The rest will be
done per-partes in the next patches.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

All n_tty related members from tty_struct will be moved here.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is a private member of n_tty. Stop accessing it. Instead, take is
as an argument.

This is needed to allow clean switch of the private members to a
separate private structure of n_tty.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

* BUG_ON(!tty) in n_tty_set_termios -- it cannot be called with tty ==
  NULL. It is called from two call sites. First, from n_tty_open where
  we have a valid tty. Second, as ld->ops->set_termios from
  tty_set_termios. But there we have a valid tty too.
* if (!tty) in n_tty_open -- why would the TTY layer call ldisc's
  open with an invalid TTY? No it indeed does not. All call sites have
  a tty and dereference that.
* BUG_ON(!tty->read_buf) in n_tty_read -- this used to be a valid
  check. The ldisc handling was broken some time ago when I added the
  check to ensure everything is OK. It still can catch the case, but
  no later than we move the buffer to ldisc data. Then there will be
  no read_buf in tty_struct, i.e. nothing to check for.
* if (!tty->read_buf) in n_tty_receive_buf -- this should never
  happen. All callers of ldisc->ops->receive_ops should hold a
  reference to an ldisc and close (which frees read_buf) cannot be
  called until the reference is dropped.
* if (WARN_ON(!tty->read_buf)) in n_tty_read -- the same as in the
  previous case.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ldisc->open and close are called only once and cannot cross. So the
tests in open and close are superfluous. Remove them. (But leave sets
to NULL to ensure there is not a bug somewhere.)

And when the tests are gone, handle properly failures in open. We
leaked read_buf if allocation of echo_buf failed before. Now this is
not the case anymore.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hci_ldisc's open checks if tty_struct->disc_data is set. And if so it
returns with an error. But nothing ensures disc_data to be NULL. And
since ld->ops->open shall be called only once, we do not need the
check at all. So remove it.

Note that this is not an issue now, but n_tty will start using the
disc_data pointer and this invalid 'if' would trigger then rendering
TTYs over BT unusable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We reintroduced tty_ldisc_wait_idle in 100eeae2 (TTY: restore
tty_ldisc_wait_idle) and used in set_ldisc. Then we added it also to
the hangup path in 92f6fa09 (TTY: ldisc, do not close until there
are readers). And we noted that there is one more path:
~   Before 65b77046 tty_ldisc_wait_idle was called also from
~   tty_ldisc_release. It is called from tty_release, so I don't think
~   we need to restore that one.

Well, I was wrong. There might still be holders of an ldisc
reference. Not from userspace, but drivers. If they take a reference
and a user closes the device immediately after that, we have a
problem. ldisc is halted and closed by TTY, but the driver still may
call some ldisc's operation and cause a crash.

So restore the tty_ldisc_wait_idle call also to the third location
where it was before 65b77046 (tty-ldisc: turn ldisc user count
into a proper refcount). Now we should be safe with respect to the
ldisc reference counting as all* tty_ldisc_close paths are safely
called with reference count of one.

* Not the one in tty_ldisc_setup's fail path. But that is called
  before the first open finishes. So userspace does not see it yet.
  Even thought the driver is given the TTY already via ->install, it
  should not take a reference to the ldisc yet. If some driver is to
  do this, we should put one tty_ldisc_wait_idle also in the setup.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There used to be a single tty_ldisc_ref_wait. But then, when a
big-tty-mutex (BTM) was introduced, it has to be tty_ldisc_ref +
tty_unlock + tty_ldisc_ref_wait + tty_lock. Later, BTM was removed
from that path and tty_ldisc_ref + tty_ldisc_ref_wait remained there.
But it makes no sense now. So leave there only tty_ldisc_ref_wait.

And when we have a reference to an ldisc, actually use it in the loop.
Otherwise it may be racy.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that we have control over tty->driver_data in pty, we can just
kill the /dev/pts/ in pty code too. Namely, in ->shutdown hook of
tty. For pty, this is called only once, for whichever end is closed
last. But we don't care, both driver_data are the inode as it used to
be till now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add kernel-doc texts for some devpts functions, i.e. document them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The goal is to stop setting and using tty->driver_data in devpts code.
It should be used solely by the driver's code, pty in this case.

Now driver_data are managed only in the pty driver. devpts_pty_new is
switched to accept what we used to dig out of tty_struct, i.e. device
node number and index.

This also removes a note about driver_data being set outside of the
driver.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The goal is to stop setting and using tty->driver_data in devpts code.
It should be used solely by the driver's code, pty in this case.

For the cleanup of layering, we will need the inode created in
devpts_pty_new to be stored into slave's driver_data. So we convert
devpts_pty_new to return the inode or an ERR_PTR-encoded error in case
of failure.

The move of 'inode = new_inode(sb);' from declarators to the code is
only cosmetical, but it makes the code easier to read.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The goal is to stop setting and using tty->driver_data in devpts code.
It should be used solely by the driver's code, pty in this case.

First, here we remove TTY from devpts_get_tty and rename it to
devpts_get_priv. Note we do not remove type safety, we just shift the
[implicit] (void *) cast one layer up.

index was unused in devpts_get_tty, so remove that from the prototype
too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When low_latency flag is set the TTY receive flip buffer is copied to the
line discipline directly instead of using a work queue in the background.
Therefor only in case a workqueue is actually used for copying data to the
line discipline we'll have to flush the workqueue.

This prevents unnecessary spin lock/unlock on the workqueue spin lock that
can cause additional scheduling overhead on a PREEMPT_RT system. On a 200
MHz AT91SAM9261 processor setup this fixes about 100us of scheduling
overhead on the TTY read call.
Signed-off-by: Ivo Sieben <meltedpianoman@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Dave Airlie recently discovered a locking bug in the fbcon layer,
where a timer_del_sync (for the blinking cursor) deadlocks with the
timer itself, since both (want to) hold the console_lock:

https://lkml.org/lkml/2012/8/21/36

Unfortunately the console_lock isn't a plain mutex and hence has no
lockdep support. Which resulted in a few days wasted of tracking down
this bug (complicated by the fact that printk doesn't show anything
when the console is locked) instead of noticing the bug much earlier
with the lockdep splat.

Hence I've figured I need to fix that for the next deadlock involving
console_lock - and with kms/drm growing ever more complex locking
that'll eventually happen.

Now the console_lock has rather funky semantics, so after a quick irc
discussion with Thomas Gleixner and Dave Airlie I've quickly ditched
the original idead of switching to a real mutex (since it won't work)
and instead opted to annotate the console_lock with lockdep
information manually.

There are a few special cases:
- The console_lock state is protected by the console_sem, and usually
  grabbed/dropped at _lock/_unlock time. But the suspend/resume code
  drops the semaphore without dropping the console_lock (see
  suspend_console/resume_console). But since the same thread that did
  the suspend will do the resume, we don't need to fix up anything.

- In the printk code there's a special trylock, only used to kick off
  the logbuffer printk'ing in console_unlock. But all that happens
  while lockdep is disable (since printk does a few other evil
  tricks). So no issue there, either.

- The console_lock can also be acquired form irq context (but only
  with a trylock). lockdep already handles that.

This all leaves us with annotating the normal console_lock, _unlock
and _trylock functions.

And yes, it works - simply unloading a drm kms driver resulted in
lockdep complaining about the deadlock in fbcon_deinit:

======================================================
[ INFO: possible circular locking dependency detected ]
3.6.0-rc2+ #552 Not tainted
-------------------------------------------------------
kms-reload/3577 is trying to acquire lock:
 ((&info->queue)){+.+...}, at: [<ffffffff81058c70>] wait_on_work+0x0/0xa7

but task is already holding lock:
 (console_lock){+.+.+.}, at: [<ffffffff81264686>] bind_con_driver+0x38/0x263

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (console_lock){+.+.+.}:
       [<ffffffff81087440>] lock_acquire+0x95/0x105
       [<ffffffff81040190>] console_lock+0x59/0x5b
       [<ffffffff81209cb6>] fb_flashcursor+0x2e/0x12c
       [<ffffffff81057c3e>] process_one_work+0x1d9/0x3b4
       [<ffffffff810584a2>] worker_thread+0x1a7/0x24b
       [<ffffffff8105ca29>] kthread+0x7f/0x87
       [<ffffffff813b1204>] kernel_thread_helper+0x4/0x10

-> #0 ((&info->queue)){+.+...}:
       [<ffffffff81086cb3>] __lock_acquire+0x999/0xcf6
       [<ffffffff81087440>] lock_acquire+0x95/0x105
       [<ffffffff81058cab>] wait_on_work+0x3b/0xa7
       [<ffffffff81058dd6>] __cancel_work_timer+0xbf/0x102
       [<ffffffff81058e33>] cancel_work_sync+0xb/0xd
       [<ffffffff8120a3b3>] fbcon_deinit+0x11c/0x1dc
       [<ffffffff81264793>] bind_con_driver+0x145/0x263
       [<ffffffff81264a45>] unbind_con_driver+0x14f/0x195
       [<ffffffff8126540c>] store_bind+0x1ad/0x1c1
       [<ffffffff8127cbb7>] dev_attr_store+0x13/0x1f
       [<ffffffff8116d884>] sysfs_write_file+0xe9/0x121
       [<ffffffff811145b2>] vfs_write+0x9b/0xfd
       [<ffffffff811147b7>] sys_write+0x3e/0x6b
       [<ffffffff813b0039>] system_call_fastpath+0x16/0x1b

other info that might help us debug this:

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(console_lock);
                               lock((&info->queue));
                               lock(console_lock);
  lock((&info->queue));

 *** DEADLOCK ***

v2: Mark the lockdep_map static, noticed by Jani Nikula.

Cc: Dave Airlie <airlied@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull arm64 fixes from Catalin Marinas:
 "Main changes:
   - AArch64 Linux compilation fixes following 3.7-rc1 changes
     (MODULES_USE_ELF_RELA, update_vsyscall() prototype)
   - Unnecessary register setting in start_thread() (thanks to Al Viro)
   - ptrace fixes"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
  arm64: fix alignment padding in assembly code
  arm64: ptrace: use HW_BREAKPOINT_EMPTY type for disabled breakpoints
  arm64: ptrace: make structure padding explicit for debug registers
  arm64: No need to set the x0-x2 registers in start_thread()
  arm64: Ignore memory blocks below PHYS_OFFSET
  arm64: Fix the update_vsyscall() prototype
  arm64: Select MODULES_USE_ELF_RELA
  arm64: Remove duplicate inclusion of mmu_context.h in smp.c

An interesting effect of using the generic version of linkage.h
is that the padding is defined in terms of x86 NOPs, which can have
even more interesting effects when the assembly code looks like this:

ENTRY(func1)
	mov	x0, xzr
ENDPROC(func1)
	// fall through
ENTRY(func2)
	mov	x0, #1
	ret
ENDPROC(func2)

Admittedly, the code is not very nice. But having code from another
architecture doesn't look completely sane either.

The fix is to add arm64's version of linkage.h, which causes the insertion
of proper AArch64 NOPs.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The min/max call needed to have explicit types on some architectures
(e.g. mn10300). Use clamp_t instead to avoid the warning:

  kernel/sys.c: In function 'override_release':
  kernel/sys.c:1287:10: warning: comparison of distinct pointer types lacks a cast [enabled by default]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull perf fixes from Ingo Molnar:
 "Assorted small fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf python: Properly link with libtraceevent
  perf hists browser: Add back callchain folding symbol
  perf tools: Fix build on sparc.
  perf python: Link with libtraceevent
  perf python: Initialize 'page_size' variable
  tools lib traceevent: Fix missed freeing of subargs in free_arg() in filter
  lib tools traceevent: Add back pevent assignment in __pevent_parse_format()
  perf hists browser: Fix off-by-two bug on the first column
  perf tools: Remove warnings on JIT samples for srcline sort key
  perf tools: Fix segfault when using srcline sort key
  perf: Require exclude_guest to use PEBS - kernel side enforcement
  perf tool: Precise mode requires exclude_guest

Namhyung Kim reported that the build fails with:

  GEN python/perf.so
  gcc: error: python_ext_build/tmp//../../libtraceevent.a: No such file or directory
  error: command 'gcc' failed with exit status 1
  cp: cannot stat `python_ext_build/lib/perf.so': No such file or directory
  make: *** [python/perf.so] Error 1

We need to propagate the TE_PATH variable to the setup.py file.
Reported-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Link: http://lkml.kernel.org/n/tip-8umiPbm4sxpknKivbjgykhut@git.kernel.org
[ Fixed superfluous variable build error. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent

Pull perf/urgent fixes from Arnaldo Carvalho de Melo:

* The python binding needs to link with libtraceevent and to initialize
  the 'page_size' variable so that mmaping works again.

* The callchain folding character that appears on the TUI just before
  the overhead had disappeared due to recent changes, add it back.

* Intel PEBS in VT-x context uses the DS address as a guest linear address,
  even though its programmed by the host as a host linear address. This either
  results in guest memory corruption and or the hardware faulting and 'crashing'
  the virtual machine.  Therefore we have to disable PEBS on VT-x enter and
  re-enable on VT-x exit, enforcing a strict exclude_guest.

  Kernel side enforcement fix by Peter Zijlstra, tooling side fix by David Ahern.

* Fix build on sparc due to UAPI, fix from David Miller.

* Fixes for the srclike sort key for unresolved symbols and when processing
  samples in JITted code, where we don't have an ELF file, just an special
  symbol table, fixes from Namhyung Kim.

* Fix some leaks in libtraceevent, from Steven Rostedt.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Pull ARM soc fixes from Olof Johansson:
 "A set of fixes and some minor cleanups for -rc2:

   - A series from Arnd that fixes warnings in drivers and other code
     included by ARM defconfigs.  Most have been acked by corresponding
     maintainers (and seem quite hard to argue not picking up anyway in
     the few exception cases).
   - A few misc patches from the list for integrator/vt8500/i.MX
   - A batch of fixes to OMAP platforms, fixing:
     - boot problems on beaglebone,
     - regression fixes for local timers
     - clockdomain locking fixes
     - a few boot/sparse warnings
   - For Tegra:
     - Clock rate calculation overflow fix
     - Revert a change that removed timer clocks and a fix for symbol
       name clashes
   - For Renesas:
     - IO accessor / annotation cleanups to remove warnings
   - For Kirkwood/Dove/mvebu:
     - Fixes for device trees for Dove (some minor cleanups, some fixes)
     - Fixes for the mvebu gpio driver
     - Fix build problem for Feroceon due to missing ifdefs
     - Fix lsxl DTS files"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
  ARM: kirkwood: fix buttons on lsxl boards
  ARM: kirkwood: fix LEDs names for lsxl boards
  ARM: Kirkwood: fix disabling CACHE_FEROCEON_L2
  gpio: mvebu: Add missing breaks in mvebu_gpio_irq_set_type
  ARM: dove: Add crypto engine to DT
  ARM: dove: Remove watchdog from DT
  ARM: dove: Restructure SoC device tree descriptor
  ARM: dove: Fix clock names of sata and gbe
  ARM: dove: Fix tauros2 device tree init
  ARM: dove: Add pcie clock support
  ARM: OMAP2+: Allow kernel to boot even if GPMC fails to reserve memory
  ARM: OMAP: clockdomain: Fix locking on _clkdm_clk_hwmod_enable / disable
  ARM: s3c: mark s3c2440_clk_add as __init_refok
  spi/s3c64xx: use correct dma_transfer_direction type
  ARM: OMAP4: devices: fixup OMAP4 DMIC platform device error message
  ARM: OMAP2+: clock data: Add dev-id for the omap-gpmc dummy fck
  ARM: OMAP: resolve sparse warning concerning debug_card_init()
  ARM: OMAP4: Fix twd_local_timer_register regression
  ARM: tegra: add tegra_timer clock
  ARM: tegra: rename tegra system timer
  ...

Emit the magic string that indicates a module has a signature after the
signature data instead of before it.  This allows module_sig_check() to
be made simpler and faster by the elimination of the search for the
magic string.  Instead we just need to do a single memcmp().

This works because at the end of the signature data there is the
fixed-length signature information block.  This block then falls
immediately prior to the magic number.

From the contents of the information block, it is trivial to calculate
the size of the signature data and thus the size of the actual module
data.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

From Jason Cooper:
 - improve #ifdef logic to prevent linker errors with CACHE_FEROCEON_L2
 - lsxl board dts fixes

* tag 'kirkwood_fixes_for_v3.7' of git://git.infradead.org/users/jcooper/linux:
  ARM: kirkwood: fix buttons on lsxl boards
  ARM: kirkwood: fix LEDs names for lsxl boards
  ARM: Kirkwood: fix disabling CACHE_FEROCEON_L2

The module build process no longer creates intermediate files for module
signing, so remove them from .gitignore.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>