- 27 Jul, 2019 40 commits
-
-
Christophe JAILLET authored
Everything is about mmc35240_ except MMC53240_WAIT_SET_RESET (3 and 5 switched). This is likely a typo. Define and use MMC35240_WAIT_SET_RESET instead. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Wolfram Sang authored
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an ERRPTR which we use in error handling. Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by:
-
Wolfram Sang authored
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an ERRPTR which we use in error handling. Signed-off-by:
-
Wolfram Sang authored
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an ERRPTR which we use in error handling. Signed-off-by:
-
Alexandru Ardelean authored
This change adds device-tree bindings for the ADIS16460. Signed-off-by:
Alexandru Ardelean <alexandru.ardelean@analog.com> Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Alexandru Ardelean authored
The ADIS16460 device is a complete inertial system that includes a triaxial gyroscope and a triaxial accelerometer. It's more simplified design than that of the ADIS16480, and does not offer the triaxial magnetometers & pressure sensors. It does also have a temperature sensor (like the ADIS16480). Since it is part of the ADIS16XXX family, it re-uses parts of the ADIS library. Naturally, the register map is different and much more simplified than the ADIS16480 subfamily, so it cannot be integrated into that driver. A major difference is that the registers are not paged. One thing that is particularly special about it, is that it requires a higher delay between CS changes (i.e. when CS goes up, the spec recommends that it be brought down after a minimum of 16 uS). Other ADIS chips require (via spec) a minimum of 2 uS between CS changes. The kernel's 10 uS default should be fine for those other chips; they haven't been tested with lower CS change delays yet. Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/adis16460.pdfSigned-off-by:
Dragos Bogdan <dragos.bogdan@analog.com> Signed-off-by:
Michael Hennerich <michael.hennerich@analog.com> Signed-off-by:
-
Alexandru Ardelean authored
The ADIS16460 requires a higher delay before the next transfer. Since the SPI framework supports configuring the delay before the next transfer, this driver will become the first user of it. The support for this functionality in ADIS16460 requires an addition to the ADIS lib to support the `cs_change_delay` functionality from the SPI subsystem. Signed-off-by:
-
Chuhong Yuan authored
Use device-managed APIs to simplify the code. The remove function is redundant now and can be deleted. Signed-off-by:
Chuhong Yuan <hslester96@gmail.com> Signed-off-by:
-
Chuhong Yuan authored
Use device-managed APIs to simplify the code. The remove functions are redundant now and can be deleted. Signed-off-by:
-
Chuhong Yuan authored
Use device-managed API to simplify the code. The remove function is redundant now and can be deleted. Signed-off-by:
-
Chuhong Yuan authored
Use device-managed APIs to simplify the code. The remove functions are redundant now and can be deleted. Signed-off-by:
-
Denis Ciocca authored
This patch is meant to replace the i2c/spi transfer functions with regmap. SPI framework requires DMA safe buffers so let's add GFP_DMA flag for memory allocation used by bulk_read functions. Signed-off-by:
Denis Ciocca <denis.ciocca@st.com> Signed-off-by:
-
Denis Ciocca authored
Some devices need to be configured with special bit in order to use spi 3-wire. This was done during device identification phase. Instead, let's move this part as spi specific. Doing this the check_device_support function becomes a simple device id check, so let's rename it. Signed-off-by:
-
Denis Ciocca authored
This patch set pressure settings right after probe start. This is done in preparation of regmap that needs different configuration based on multiread bit value. Signed-off-by:
-
Denis Ciocca authored
This patch set magn settings right after probe start. This is done in preparation of regmap that needs different configuration based on multiread bit value. Signed-off-by:
-
Denis Ciocca authored
This patch set gyro settings right after probe start. This is done in preparation of regmap that needs different configuration based on multiread bit value. Signed-off-by:
-
Denis Ciocca authored
This patch set accel settings right after probe start. This is done in preparation of regmap that needs different configuration based on multiread bit value. Signed-off-by:
-
Denis Ciocca authored
The function is introduced to retrieve press device settings. It will be used by probe in order to configure regmap. Signed-off-by:
-
Denis Ciocca authored
The function is introduced to retrieve magn device settings. It will be used by probe in order to configure regmap. Signed-off-by:
-
Denis Ciocca authored
The function is introduced to retrieve gyro device settings. It will be used by probe in order to configure regmap. Signed-off-by:
-
Denis Ciocca authored
The function is introduced to retrieve accel device settings. It will be used by probe in order to configure regmap. Signed-off-by:
-
Denis Ciocca authored
Extract from st_sensors_check_device_support() function the code that is used to get the specific settings for a device. This will be used as generic extractor by each ST driver. Signed-off-by:
-
Gwendal Grignou authored
Due to an API misread, error code can be different for -EIO when reading a sysfs entry. Return the error reported by the cros_ec stack. Check the proper error message (protocol error, not supported) is reported when there is an error returned by the EC stack. Signed-off-by:
Gwendal Grignou <gwendal@chromium.org> Signed-off-by:
-
Gwendal Grignou authored
Add calibration scale support to accel, gyro and magnetometer. Check on eve with current firmware, check reading calibscale returns 1.0, check with newer firmware values are applied. Signed-off-by:
-
Christophe JAILLET authored
s/ADPS9960/APDS9960/ (P and D switched) Signed-off-by:
-
Christophe JAILLET authored
All #define are about SCA3000_... except the last one. Make it consistent. s/SAC3000/SCA3000/ This #define is apparently unused up to now. Signed-off-by:
-
Benjamin Gaignard authored
Quadrature feature is now hosted on it own framework. Remove quadrature related code from stm32-trigger driver to avoid code duplication and simplify the ABI. Signed-off-by:
Benjamin Gaignard <benjamin.gaignard@st.com> Signed-off-by:
-
Bárbara Fernandes authored
Create list of compatible device ids to be matched with those stated in the device tree. Signed-off-by:
Bárbara Fernandes <barbara.fernandes@usp.br> Signed-off-by:
Wilson Sales <spoonm@spoonm.org> Co-developed by: Wilson Sales <spoonm@spoonm.org> Signed-off-by:
-
Lorenzo Bianconi authored
Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
Lorenzo Bianconi authored
Add support to STM LSM6DS3TR-C 6-axis (acc + gyro) Mems sensor https://www.st.com/resource/en/datasheet/lsm6ds3tr-c.pdfSigned-off-by:
-
Geert Uytterhoeven authored
"git diff" says: \ No newline at end of file after modifying the files. Signed-off-by:Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
-
Fabrice Gasnier authored
On stm32h7 and stm32mp1, the ADC inputs are multiplexed with analog switches which have reduced performances when their supply is below 2.7V (vdda by default): - 3.3V embedded booster can be used, to get full ADC performances (increases power consumption). - vdd supply can be selected if above 2.7V by setting ANASWVDD syscfg bit, on STM32MP1 only. Make this optional, since this is a trade-off between analog performance and power consumption. Signed-off-by:
Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by:
-
Fabrice Gasnier authored
On stm32h7 and stm32mp1, the ADC inputs are multiplexed with analog switches which have reduced performances when their supply is below 2.7V (vdda by default). Booster or vdd can be used, to get full ADC performances. Add documentation for: - optional booster-supply that can be used on stm32h7 and stm32mp1. - optional vdd-supply that can be used on stm32mp1 to supply analog circuitry, selected by syscfg. Mark these as optional, since this is a trade-off between analog performance and power consumption. Signed-off-by:
-
Luca Weiss authored
Add device tree support for the stk33xx family of ambient light sensors. Tested-by:
Martijn Braam <martijn@brixit.nl> Signed-off-by:
Luca Weiss <luca@z3ntu.xyz> Signed-off-by:
-
Luca Weiss authored
Add binding documentation for the stk33xx family of ambient light sensors. Signed-off-by:
-
Luca Weiss authored
Sensortek Technology Corp. produces Proximity Sensors with ALS and Accelerometers. Signed-off-by:
-
Fuqian Huang authored
iio: imu: mpu6050: Replace devm_add_action() followed by failure action with devm_add_action_or_reset() devm_add_action_or_reset() is introduced as a helper function which internally calls devm_add_action(). If devm_add_action() fails then it will execute the action mentioned and return the error code. This reduce source code size (avoid writing the action twice) and reduce the likelyhood of bugs. Signed-off-by:
Fuqian Huang <huangfq.daxian@gmail.com> Signed-off-by:
-
Fuqian Huang authored
iio: adc: sc27xx: Replace devm_add_action() followed by failure action with devm_add_action_or_reset() devm_add_action_or_reset() is introduced as a helper function which internally calls devm_add_action(). If devm_add_action() fails then it will execute the action mentioned and return the error code. This reduce source code size (avoid writing the action twice) and reduce the likelyhood of bugs. Signed-off-by:
-
Fuqian Huang authored
Introduce local variable 'struct device *dev' and use it instead of dereferencing it repeatly. Signed-off-by:
-
Tomasz Duszynski authored
Add myself as a plantower pms7003 driver maintainer. Signed-off-by:
Tomasz Duszynski <tduszyns@gmail.com> Signed-off-by:
-
