The fw_rx_stats entry in debugfs was getting truncated because the
internal buffer used to hold the string was too short.  The
calculation of the needed buffer size was rather bogus.

Simplify the calculation by multiplying the number of entries in the
entire structure by the size of each data line and adding the size of
the header lines.

Additionally, add the mac_id value, which was missing.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The activity grading indication from the firmware should
not be used in this case, but the bt_status in the firwmare
notification.
Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The firmware always expects the Coex Mode to be set.
Moreover, the firmware expects bit 0 is the valid bits to
be set all the times.
I misunderstood the API and didn't set these bits when
commands are sent to update the paramters of the Coex. As
a result, the firmware understood that the BT Coex was
disabled (Coex mode = 0) and ignored all the updates (valid
bit 0 clear).

Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Section size limitation to 6000 is incorrect.
NVM file need to support bigger sections in order
to support PAPD tables.
Signed-off-by: Idan Kahlon <idanx.kahlon@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Maor Perez <maorx.perez@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Support Signed firmware based on code signing system (CSS)
protocol and dual CPUs download,
the code recognize if there are more than one CPU and
if we need to operate the signed protocol according to
the ucode binary image
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

At the firmware level, IBSS support has similar programming
requirements as AP/GO support, so use the same functions with
just small differences.

With IBSS only a single virtual interface can be used, so no
changes in the advertised interface combinations are needed.

For now, don't use hardware crypto for the GTKs in IBSS mode,
the firmware should support it though.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

7265 is a very similar device to 7260, so just add
the definitions based on 7260 for it.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Remove code that is not needed and always allow MIMO when
in tight mode. In loose mode, we should avoid MIMO since BT
can use the other antenna to Rx while we Tx.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The code limiting the AMPDU length due to BT traffic was
duplicated. Remove the redundant code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Tests have shown that we should start AMPDU even when BT
is active. So remove that constraint.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Tests have shown that we should go SMSP_STATIC when BT
traffic is high, and stay in dynamic if BT traffic is low.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

BT Coex needs to be updated when the bandwidth is modified
by the AP.
While at it, remove the vif parameter from
bt_coex_vif_change since it was unused.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Until now, after WoWLAN, we weren't able to keep the
connection to the AP because the firmware didn't give
us the right information. Since the firmware API has
been changed to include all the information we need,
change the driver to work with the new API (if it is
available) and program all the relevant information
in mac80211 to keep the connection.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some NICs embedded in platforms that have only 16 Tx queues,
this affect the mapping of the Tx queues.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some NICs aren't allowed to be powered up at driver load time.
Fix it, and move the external NVM loading from driver load time to
driver up time (parsing the external nvm file remains at driver load time).
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

FW starts using legacy power table command (0x77) for device wide power
settings. Currently this command contains only option flags field.
It can configure the following: CAM (Continuous Active Mode) and
POWER_SAVE_ENABLE debug option. Send this command when firmware is
loaded - D0 and D3.
Note: Setting this command is important to avoid unwanted FW behavior.
It particularly fixes a bug when a device does not drop to low power
after disassociation from AP.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This should really not happen. If it does, restarting is the
only way to recover since the driver and the firmware might
very well be out of sync. Moreover, iwl_op_mode_nic_error
will print data that might help debugging.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Single shared antenna devices need a special LUT.
Address this need.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In loose BT Coex scheme, the aggregation size doesn't need to
be limited.

To avoid triggering it, remove a lockdep assertion - we need
to compute the AMPDU size limit from rate control code which
can't take mvm->mutex. This means that there is a race but in
the worst case, we will have a wrong AMPDU size limit which
is not a big issue.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The Ralink DPO_RT5572_LinuxSTA_2.6.1.3_20121022
reference driver uses different RSSI threshold
and VGC adjustment values for the RT3572 and
RT3593 chipsets.

Update the rt2800_link_tuner function to use the
same values. Also change the comment in the function
to make it more generic.

References:

  RT35xx_ChipAGCAdjust function in chips/rt35xx.c
  RSSI_FOR_MID_LOW_SENSIBILITY constant in include/chip/rtmp_phy.h
  RT3593_R66_MID_LOW_SENS_GET macro in include/chip/rt3593.h
  RT3593_R66_NON_MID_LOW_SEMS_GET macro in include/chips/rt3593.h
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In commit 3d81535e
(rt2800: 5592: add chip specific vgc calculations)
the rt2800_link_tuner function has been modified to
adjust VGC level for the RT5592 chipset.

On the RT5592 chipset, the VGC level must be adjusted
only if rssi is greater than -65. However the current
code adjusts the VGC value by 0x10 regardless of the
actual chipset if the rssi value is between -80 and
-65.

Fix the broken behaviour by reordering the if-else
statements.

Cc: stable@vger.kernel.org
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove the local MOVING_AVERAGE implementation, and use
the generic EWMA functions instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In rt2800_config_channel_rf3xxx(), there's no need to toggle
RF R30 bit 7 twice.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch proposes to remove the use of the IRQF_DISABLED flag

It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Pausing queue on flush make no sense since txdone procedure un-pause
queue. Before flush procedure we have to assure queue is stopped,
i.e. on receive path h/w RX is disabled, on transmit path queue is
disabled in mac80211. That conditions are true except one function:
rt2x00usb_watchdog_tx_dma(), so add stop/start queue there.

Note stop/start queue can be racy if we do this from multiple paths,
but currently we stop TX queues only on rt2x00lib_disable_radio(),
which also stop/sync watchdog, hance we have no race condition.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The rt2x00 driver uses 0x22 as a default VGC value
in VGC adjustment for the RT3572 chipset. In the
Ralink DPO_RT5572_LinuxSTA_2.6.1.3_20121022 driver,
this value is only used for initialization. During
VGC adjustment, the reference driver uses different
values.

Update the 'rt2800_get_default_vgc' function to
synchronize the values with the reference driver.
Also add the missing AGC initialization code into
the 'rt2800_config_channel' function.

References:
  RT35xx_SetAGCInitValue in chip/rt35xx.c
  RT35xx_ChipAGCAdjust in chip/rt35xx.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

According to the DPO_RT5572_LinuxSTA_2.6.1.3_20121022
reference driver, programming of the 'BBP 66' register
on the RT3572 and RT3593 chipsets must be done via the
'rt2800_bbp_write_with_rx_chain' function. This ensures
that value is correclty set for all RX chains.

References:
  RT35xx_ChipAGCAdjust and RT35xx_SetAGCInitValue functions
  in chips/rt35xx.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Update the rt2800_get_default_vgc function to use the same VGC
values that the DPO_RT5572_LinuxSTA_2.6.1.3_20121022 reference
driver uses.

References:
  RT35xx_ChipAGCAdjust in chips/rt35xx.c
  RT3593_R66_MID_LOW_SENS_GET macro in include/chip/rt3593.h
  RT3593_R66_NON_MID_LOW_SEMS_GET macro in include/chips/rt3593.h
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The TXPOWER_DELTA field of the regular EEPROM
stores the TX power compensation value for HT40.
The extended EEPROM has no such field, it stores
separate TX power values for HT20 and for HT40.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The comments are indicating that the TXMIXER_GAIN_BG
and TXMIXED_GAIN_A entries are overlapping with the
RSSI_BG2 and RSSI_A2 entries in the extended EEPROM
map. This is not correct, because the upper byte of
the RSSI_BG2 and RSSI_A2 entries are reserved. There
are no TX mixer gain values are stored at all in the
extended EEPROM.

Remove the initialization of these entries from the
extended EEPROM map to reflect this.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There are some BCM4313 out there with a PCI id of 0x4313. These devices
are missing a sprom and are only used on routers or other embedded
devices. We found one connected to a BCM63XX SoC.

This devices was found by someone in this ticket:
https://dev.openwrt.org/ticket/13551Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This PCI id is used by some BCM4313 cards without a sprom. I have seen
such a card on a router connected to some BCM63XX SoC via PCIe. There
are cards out there with the same PCI id and a BCM4311, which is a pre
ieee80211n chip only supporting ieee80211a, these are still not
supported by b43 and not detected by ssb.

This devices was found by someone in this ticket:
https://dev.openwrt.org/ticket/13551Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma currently only supports PCIe cards and no PCI cards, reject them
if we find them. I have never heard of any PCI card using the AI bus
(bcma), all of them are using ssb instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

TI firmwares are located under ti-connectivity
directory. Update path to make sure driver can
find and load firmware blob.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently driver name is wrong. PCI device address is visible at
/proc/interrupts instead of the name:

 43:    124      0      0      0   PCI-MSI-edge    rtsx_pci
 44:    384      0      0      0   PCI-MSI-edge    snd_hda_intel
 45:  25096      0      0      0   PCI-MSI-edge    0000:01:00.0
                                                   ^^^^^^^^^^^^

So, pass the right name. rt2x00_ops->name contains KBUILD_MODNAME
and good for that, so pass it.

Handler names will be "rt2500pci", "rt2500pci" etc.
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru>
CC: Ivo van Doorn <IvDoorn@gmail.com>
CC: Gertjan van Wingerde <gwingerde@gmail.com>
CC: Helmut Schaa <helmut.schaa@googlemail.com>
CC: linux-wireless@vger.kernel.org
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is a mac80211 driver for Qualcomm WCN3660/WCN3680 devices. So
far WCN3660/WCN3680 is available only on MSM platform.

Firmware can be found here:
https://www.codeaurora.org/cgit/external/hisense/platform/vendor/qcom-opensource/wlan/prima/tree/firmware_bin?h=8130_CS

Wiki page is available here:
http://wireless.kernel.org/en/users/Drivers/wcn36xx

A lot people made a contribution to this driver. Here is the list in
alphabetical order:

Eugene Krasnikov <k.eugene.e@gmail.com>
Kalle Valo <kvalo@qca.qualcomm.com>
Olof Johansson <dev@skyshaper.net>
Pontus Fuchs <pontus.fuchs@gmail.com>
Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Eugene Krasnikov <k.eugene.e@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The variables cancel_scan_cmd, enable_data, hs_activate and valid are
only assigned the values true and false. Change its type to bool.

The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):

@exists@
type T;
identifier b;
@@
- T
+ bool
  b = ...;
  ... when any
  b = \(true\|false\)
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

0411,0241  RT5572  BUFFALO WI-U2-300D Wireless LAN Adapter
0789,0170  RT3572  Logitec LAN-W300AN/U2
0846,9013  RT3573  NETGEAR Adaptador USB Inalambrico Movistar
0df6,006e  RT3573  Sitecom WiFi USB adapter N900
2001,3c1f  RT3573  D-Link DWA-162 Wireless N900 Dual Band Adapter
2001,3c20  RT5372  D-Link DWA-140 Wireless N USB Adapter(rev.D)
2001,3c21  RT5572  D-Link DWA-160 Xtreme N Dual Band USB Adapter(rev.C)
2001,3c22  RT5372  D-Link DWA-132 Wireless N USB Adapter(rev.B)
2001,3c23  RT5372  D-Link GO-USB-N300 Wireless N Easy USB Adapter
2019,ab29  ?       Planex GW-USMirco300
20f4,724a  RT5572  TRENDnet N600 Wireless Dual Band USB Adapter

Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: users@rt2x00.serialmonkey.com
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>