* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6: (44 commits)
  i2c: Delete the i2c-isa pseudo bus driver
  hwmon: refuse to load abituguru driver on non-Abit boards
  hwmon: fix Abit Uguru3 driver detection on some motherboards
  hwmon/w83627ehf: Be quiet when no chip is found
  hwmon/w83627ehf: No need to initialize fan_min
  hwmon/w83627ehf: Export the thermal sensor types
  hwmon/w83627ehf: Enable VBAT monitoring
  hwmon/w83627ehf: Add support for the VID inputs
  hwmon/w83627ehf: Fix timing issues
  hwmon/w83627ehf: Add error messages for two error cases
  hwmon/w83627ehf: Convert to a platform driver
  hwmon/w83627ehf: Update the Kconfig entry
  make coretemp_device_remove() static
  hwmon: Add LM93 support
  hwmon: Improve the pwmN_enable documentation
  hwmon/smsc47b397: Don't report missing fans as spinning at 82 RPM
  hwmon: Add support for newer uGuru's
  hwmon/f71805f: Add temperature-tracking fan control mode
  hwmon/w83627ehf: Preserve speed reading when changing fan min
  hwmon: fix detection of abituguru volt inputs
  ...

Manual fixup of trivial conflict in MAINTAINERS file

If root raised the default wakeup threshold over the size of the
output pool, the pool transfer function could overflow the stack with
RNG bytes, causing a DoS or potential privilege escalation.

(Bug reported by the PaX Team <pageexec@freemail.hu>)

Cc: Theodore Tso <tytso@mit.edu>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
  ocfs2: ->fallocate() support

* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
  [PATCH] sched: implement cpu_clock(cpu) high-speed time source
  [PATCH] sched: fix the all pinned logic in load_balance_newidle()
  [PATCH] sched: fix newly idle load balance in case of SMT
  [PATCH] sched: sched_cacheflush is now unused

When a CONFIG_USER_NS=n and a user tries to unshare some namespace other
than the user namespace, the dummy copy_user_ns returns NULL rather than
the old_ns.

This value then gets assigned to task->nsproxy->user_ns, so that a
subsequent setuid, which uses task->nsproxy->user_ns, causes a NULL
pointer deref.

Fix this by returning old_ns.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The slab and slob allocators already did this right, but slub would call
"get_object_page()" on the magic ZERO_SIZE_PTR, with all kinds of nasty
end results.

Noted by Ingo Molnar.

Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I suspect Christoph tested his code only in the NUMA configuration, for
the combination of SLAB+non-NUMA the zero-sized kmalloc's would not work.

Of course, this would only trigger in configurations where those zero-
sized allocations happen (not very common), so that may explain why it
wasn't more widely noticed.

Seen by by Andi Kleen under qemu, and there seems to be a report by
Michael Tsirkin on it too.

Cc: Andi Kleen <ak@suse.de>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Implement the cpu_clock(cpu) interface for kernel-internal use:
high-speed (but slightly incorrect) per-cpu clock constructed from
sched_clock().

This API, unused at the moment, will be used in the future by blktrace,
by the softlockup-watchdog, by printk and by lockstat.
Signed-off-by: Ingo Molnar <mingo@elte.hu>

nr_moved is not the correct check for triggering all pinned logic. Fix
the all pinned logic in the case of load_balance_newidle().
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

In the presence of SMT, newly idle balance was never happening for
multi-core and SMP domains (even when both the logical siblings are
idle).

If thread 0 is already idle and when thread 1 is about to go to idle,
newly idle load balance always think that one of the threads is not idle
and skips doing the newly idle load balance for multi-core and SMP
domains.

This is because of the idle_cpu() macro, which checks if the current
process on a cpu is an idle process. But this is not the case for the
thread doing the load_balance_newidle().

Fix this by using runqueue's nr_running field instead of idle_cpu(). And
also skip the logic of 'only one idle cpu in the group will be doing
load balancing' during newly idle case.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Since Ingo's recent scheduler rewrite which was merged as commit
0437e109 sched_cacheflush is unused.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

There are no users of i2c-isa left, so we can finally get rid of it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

With this patch the abituguru refuses to load on non Abit motherboards, as
discussed in lkml CONFIG_BREAK_MY_MACHINE thread.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

This patch changes the driver to also detect uguru3's which hold 0x08 at DATA
initially, as has been reported here:
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=220160

Also when an uguru3's holds 0x0014 in the ID register it will now report
"Abit AB9 Pro" as motherboard identification.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

This fixes bug #8593:
http://bugzilla.kernel.org/show_bug.cgi?id=8593Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

We don't need to initialize fan_min in this driver, as the fan_div
attributes are read-only.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

Add support for the w83627ehf thermal sensor types. I made them read-only,
as the BIOS is supposed to set them up properly. This information makes it
easier to find out which temperature channel corresponds to the CPU.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

If VBAT monitoring is disabled, enable it. Original patch from
an anonymous contributor on the lm-sensors trac system:
http://lm-sensors.org/ticket/2218Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

The W83627EHF and similar chips have 6 VID input pins, add support
for them. The driver changes the input voltage level automatically
if the current setting is not correct for the detected CPU model.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

* I have experimental evidence that the W83627EHG needs more than 1
second to refresh all the measured values. Increase the caching time to
1.5 second.
* When changing a fan clock divider, the corresponding fan speed
measurement register is no longer valid, until the next time the chip
will refresh it. One way to fix this is to pretend that the cache is
still valid for one more period (1.5 second.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

If the Super-I/O device is disabled, it is likely the BIOS has a good
reason for leaving it disabled, so give a warning when enabling it --
it's not likely to be wired correctly or be able to give good data.

Also, if the Super-I/O device is configured with an address of 0, the
driver refuses to initialize it.
Signed-off-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

Remove i2c-isa from the w83627ehf driver, and use a platform driver
instead.
Signed-off-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

Add description for the W83627DHG chip to Kconfig.
Signed-off-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

coretemp_device_remove() can become static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

This patch adds support for the LM93 hardware monitoring chip.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

The documentation of the pwmN_enable interface file is not very clear,
and has been confusing several driver authors already. Make it clearer.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

Also protects ourselves against a possible division by zero.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

This patch adds a new driver for the hardware monitoring features of the
third revision of the Abit uGuru chip, found on recent Abit
motherboards. This is an entirely different beast then the first and
second revision (its again a winbond microcontroller, but the "protocol"
to talk to it and the bank addresses are very different.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

Add support for the "temperature mode" fan speed control. In this mode,
the user can define 3 temperature/speed trip points, and the chip will
set the speed automatically according to the temperature changes.
Signed-off-by: Phil Endecott <kernel@chezphil.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

The w83627ehf driver changes the fan clock divider automatically when
a new min fan speed is set. It is supposed to preserve the fan speed
reading while doing so, bug doesn't really. Fix it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

This patch fixes the detection of volt inputs with a reading of more then 240
units.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

This patch adds the SMSC SCH5317 chip (device ID 0x85) as a supported
device to the smsc47b397 driver.

Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

This is the patch for converting it87 to a platform driver (and remove i2c-isa).
Signed-off-by: Corentin LABBE <corentin.labbe@geomatys.fr>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

Fix a potential race condition when some hardware monitoring platform
drivers are being unloaded. I believe that the driver data pointer
shouldn't be cleared before all the sysfs files are removed, otherwise
a sysfs callback might attempt to dereference a NULL pointer. I'm not
sure exactly what the driver core protects drivers against, so let's
play it safe.

While we're here, clear the driver data pointer when probe fails, so
as to not leave an invalid pointer behind us.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

Convert the vt8231 driver from the nonsensical i2c-isa hack to a
regular platform driver.
Signed-off-by: Roger Lucas <roger@planbit.co.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

Use PCI_REVISION_ID instead of our own define.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

This lets us get rid of macro-generated functions and shrinks the
driver size by about 7%.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Convert the sis5595 driver from the nonsensical i2c-isa hack to a
regular platform driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

This lets us get rid of macro-generated functions and shrinks the
driver size by about 9%.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Convert the via686a driver from the nonsensical i2c-isa hack to a
regular platform driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>