- 26 Nov, 2008 31 commits
-
-
Winkler, Tomas authored
This instructs FH to increment the retry count of a packet when it is brought from the memory to TX-FIFO to save transactions during aggregation flow. Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
Reinette Chatre <reinette.chatre@intel.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Winkler, Tomas authored
This patch configures correctly TX DMA channel. It is not the same as TX queue. Signed-off-by:
Zhu Yi <yi.zhu@intel.com> Signed-off-by:
-
Winkler, Tomas authored
Apply same idiom as in 5000 introduced by 'iwlwifi: define firmware file name once' Signed-off-by:
-
Tomas Winkler authored
This patch adds base band calibration support. Signed-off-by:
-
Winkler, Tomas authored
This patch moves iwl_clear_stations_table into iwl-sta.c Signed-off-by:
-
Abhijeet Kolekar authored
Patch fixes the ad-hoc mode by 1) Removing redundant clear_stations_table which prevented generation of beacons. 2) Setting assoc_id to 1. It was never set so preventing tx flow in iwl3945_tx_skb. Signed-off-by:
Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by:
-
Bob Copeland authored
Configure the mac address in add_interface and clear it in remove_interface so that users can change the mac address to something other than the one in the eeprom. Also avoid setting it at attach time so that we won't ack packets until fully set up. Signed-off-by:
Bob Copeland <me@bobcopeland.com> Signed-off-by:
-
Sujith authored
Signed-off-by:
Sujith <Sujith.Manoharan@atheros.com> Signed-off-by:
-
Sujith authored
Signed-off-by:
-
Sujith authored
CHANNEL_CCK flag is set for all 2 Ghz channels, so IS_CHAN_CCK() would turn out to be true for all channles in that band. Use IS_CHAN_B() now, which checks the channel mode and not the channel flags. Signed-off-by:
-
Sujith authored
Also, use a helper function to setup RC status data when processing completed TX descriptors. Signed-off-by:
-
Sujith authored
Break down huge functions, use helper functions or macros instead. Signed-off-by:
-
Sujith authored
Replace TRUE/FALSE macros with VALID/INVALID macros. Follow a consistent variable convention. Remove unnecessary comments. Add all RC phy macros into a single enum. Merge functions into reasonably sized entities. Signed-off-by:
-
Sujith authored
Maintaining two sets of rate tables is redundant, remove one and use struct ath_rate_table exclusively. Signed-off-by:
-
Sujith authored
Remove the hack using vif, and use rate_driver_data within skb->cb to hold driver specific rate information. Setup the rate series in the skb's tx control area and remove all references to ath9k specific rate series ( using struct ath_rc_series ). Signed-off-by:
-
Sujith authored
Move the hw rate tables to ath_softc, and access them directly. tx_triglevel_max is global, move it to ath_rate_node. Now that ath_rate_softc is gone, rate control attach becomes simpler. Signed-off-by:
-
Sujith authored
Rate control init is now confined to itself, using the HT capabilites of the STA from rate_init(). Signed-off-by:
-
Sujith authored
Signed-off-by:
-
Sujith authored
Remove a lot of old, crufty code and make RX status reporting a bit sane and clean. Do not do anything to the RX skb before unmapping. So in ath_rx_tasklet(), move the skb_put() after PCI unmap. Signed-off-by:
-
Sujith authored
Signed-off-by:
-
Sujith authored
Half/Quarter rate tables are needed only for legacy chipsets. Signed-off-by:
-
Sujith authored
Signed-off-by:
-
Sujith authored
Setup legacy rates in ath_rate_init() itself. Signed-off-by:
-
Sujith authored
Signed-off-by:
-
Sujith authored
Avoid casting of ath_tx_ratctrl and access the elements directly. Signed-off-by:
-
Vasanthakumar Thiagarajan authored
[ 6133.670329] BUG: unable to handle kernel NULL pointer dereference at 0000000000000010 [ 6133.672802] IP: [<ffffffffa030fcf6>] ieee80211_stop_queues+0x26/0x40 [mac80211] [ 6133.672802] PGD 759dc067 PUD 74f1d067 PMD 0 [ 6133.672802] Oops: 0002 [#1] PREEMPT SMP [ 6133.672802] last sysfs file: /sys/class/backlight/acpi_video0/brightness [ 6133.672802] CPU 0 [ 6133.672802] Modules linked in: ath9k(-) mac80211 pciehp pci_hotplug arc4 ecb joydev pcmcia ppdev lp ppp_generic psmouse sg pcspkr s] [ 6133.735830] Pid: 4445, comm: rmmod Tainted: G W 2.6.28-rc5-wl #1 [ 6133.735830] RIP: 0010:[<ffffffffa030fcf6>] [<ffffffffa030fcf6>] ieee80211_stop_queues+0x26/0x40 [mac80211] [ 6133.735830] RSP: 0018:ffff88007d1efd10 EFLAGS: 00010246 [ 6133.735830] RAX: 0000000000000000 RBX: ffff880074f41aa0 RCX: 0000000000000000 [ 6133.735830] RDX: 0000000000000010 RSI: 0000000000000000 RDI: ffff880074f40340 [ 6133.735830] RBP: ffff880074990000 R08: 0000000000000000 R09: 000000000000224d [ 6133.735830] R10: 0000000000000000 R11: ffffffff8031dc70 R12: 0000000000000000 [ 6133.735830] R13: 0000000000000001 R14: ffff880074f46c9c R15: 0000000000000000 [ 6133.735830] FS: 00007f1e2e0bc6f0(0000) GS:ffffffff805e0b80(0000) knlGS:0000000000000000 [ 6133.735830] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 6133.735830] CR2: 0000000000000010 CR3: 0000000075593000 CR4: 00000000000006e0 [ 6133.735830] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 6133.735830] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 [ 6133.735830] Process rmmod (pid: 4445, threadinfo ffff88007d1ee000, task ffff88007c0c8000) [ 6133.735830] Stack: [ 6133.735830] ffffffffa034d583 ffff88007c7d9410 ffff88007c7d9410 ffff88007c7d9410 [ 6133.735830] ffffffff80481dab ffff880074f41aa0 00000000fffffff0 0000000000000000 [ 6133.735830] 0000000000000001 0000000000000001 ffffffffa034d8a5 ffff88007c7d9400 [ 6133.735830] Call Trace: [ 6133.735830] [<ffffffffa034d583>] ? ath_radio_disable+0x33/0x150 [ath9k] [ 6133.735830] [<ffffffff80481dab>] ? __mutex_lock_slowpath+0x20b/0x2a0 [ 6133.735830] [<ffffffffa034d8a5>] ? ath_sw_toggle_radio+0x65/0xa0 [ath9k] [ 6133.735830] [<ffffffffa019d1f4>] ? rfkill_toggle_radio+0x74/0x140 [rfkill] [ 6133.735830] [<ffffffffa019d597>] ? rfkill_remove_switch+0x67/0x80 [rfkill] [ 6133.735830] [<ffffffffa019d955>] ? rfkill_unregister+0x25/0x50 [rfkill] [ 6133.735830] [<ffffffffa034bf75>] ? ath_detach+0xf5/0x140 [ath9k] [ 6133.735830] [<ffffffffa034bfe9>] ? ath_pci_remove+0x29/0x80 [ath9k] [ 6133.735830] [<ffffffff8035263c>] ? pci_device_remove+0x2c/0x60 [ 6133.735830] [<ffffffff803c3829>] ? __device_release_driver+0x99/0x100 [ 6133.735830] [<ffffffff803c3950>] ? driver_detach+0xc0/0xd0 [ 6133.735830] [<ffffffff803c296e>] ? bus_remove_driver+0x8e/0xd0 [ 6133.735830] [<ffffffff80352916>] ? pci_unregister_driver+0x36/0xa0 [ 6133.735830] [<ffffffffa0356ad4>] ? exit_ath_pci+0x10/0x29 [ath9k] [ 6133.735830] [<ffffffff8026bb1b>] ? sys_delete_module+0x1cb/0x2d0 [ 6133.735830] [<ffffffff802960d9>] ? do_munmap+0x349/0x390 [ 6133.735830] [<ffffffff80342d01>] ? __up_write+0x21/0x150 [ 6133.735830] [<ffffffff8020c45b>] ? system_call_fastpath+0x16/0x1b [ 6133.735830] Code: c3 0f 1f 40 00 0f b7 57 5e 0f b7 47 5c 01 c2 74 30 31 c9 66 90 48 8b 57 78 0f b7 c1 48 c1 e0 07 48 03 82 00 03 00 [ 6133.735830] RIP [<ffffffffa030fcf6>] ieee80211_stop_queues+0x26/0x40 [mac80211] Signed-off-by:
Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by:
-
Larry Finger authored
In the commit entitled "mac80211/drivers: rewrite the rate control API", the meaning of the packet transmit count was changed from the number of retries to the total number. In driver rtl8187, this change was missed. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Acked-by:
Herton Ronaldo Krzesinski <herton@mandriva.com.br> Tested-by:
Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by:
-
Larry Finger authored
In commit 9ea2c74 named "mac80211/drivers: rewrite the rate control API", the meaning of status.rates[i].count was changed from number of retries to total number of tries. As a result, the pid rate-setting algorithm fails because every packet appears to have needed a retransmit. Signed-off-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Ivo van Doorn authored
When we switch off the LEDS during initialization we kill rt73usb from proper functioning. The immediate result after the first LED command are MCU failures and a complete breakdown of TX/RX. Signed-off-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
-
Andrey Borzenkov authored
Since WE7 /proc/net/wireless checks whether level and noise are in dBm and shows them accordingly. Indicate that we return signal and noice levels in dBm. Before: Inter-| sta-| Quality | Discarded packets | Missed | WE face | tus | link level noise | nwid crypt frag retry misc | beacon | 22 eth1: 0000 65. 219. 165. 0 0 148 41 0 0 After: Inter-| sta-| Quality | Discarded packets | Missed | WE face | tus | link level noise | nwid crypt frag retry misc | beacon | 22 eth1: 0000 65. -37. -91. 0 0 0 0 0 0 While at it, replace raw numbers with appropriate macro. Signed-off-by:
Andrey Borzenkov <arvidjaar@mail.ru> Signed-off-by:
Pavel Roskin <proski@gnu.org> Signed-off-by:
-
Luis R. Rodriguez authored
This makes minstrel the default rate control algorithm for mac80211. For more information see: http://wireless.kernel.org/en/developers/Documentation/mac80211/RateControl/minstrel If someone can come up with a better algorithm they get a prize (undisclosed). Signed-off-by:
Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by:
-
- 25 Nov, 2008 9 commits
-
-
Luis R. Rodriguez authored
mac80211's ieee80211_register_hw() is often called within the probe path so it cannot assume the device's driver structure has been attached yet so to create a workqueue instead of using driver->name use the wiphy's phy%d name. The name doesn't really matter anyway. This should fix sporadic oopses found when we race to beat the driver pointer setting. Not even sure how this was working properly. http://www.kerneloops.org/search.php?search=ieee80211_register_hwSigned-off-by:
-
Vasanthakumar Thiagarajan authored
This fixes the poor wireless connection which happens even if we are very well in the range. Signed-off-by: Don.breslin@atheros.com Signed-off-by:
-
Christian Lamparter authored
As was pointed out in "p54: honour bss_info_changed's short slot time settings", bss_info_changed provides more useful settings that can be used by the driver. Signed-off-by:
Christian Lamparter <chunkeey@web.de> Signed-off-by:
-
Christian Lamparter authored
Johannes pointed out that the driver has cache the firmware for suspend/resume cycles. Signed-off-by:
-
Christian Lamparter authored
This patch contains only contains a one-liner fixes and enhancements Signed-off-by:
-
Christian Lamparter authored
This patch enables Mesh Point operation for any p54 device. Signed-off-by:
-
Sujith authored
Signed-off-by:
-
Luis R. Rodriguez authored
Make the DMAable mameory consistent with pci_set_consistent_dma_mask(). The DMA-mapping.txt Documentation recommends this but for PCI-X considerations and on strange architecture like SGI SN2, not sure why it would fix an issue but lets see if it does, just in case. Before this, this driver was tested with x86_64 with about 7 GB of RAM, not sure if this is really needed. Signed-off-by:
-
Luis R. Rodriguez authored
Use DMA_32BIT_MASK to clarify we only want 32-bit DMA memory. What was there before is also 32-bit but this makes it clearer Signed-off-by:
-
