We are about to modify the VGIC to allocate all data structures
dynamically and store mapped IRQ information on a per-IRQ struct, which
is indeed allocated dynamically at init time.

Therefore, we cannot record the mapped IRQ info from the timer at timer
reset time like it's done now, because VCPU reset happens before timer
init.

A possible later time to do this is on the first run of a per VCPU, it
just requires us to move the enable state to be a per-VCPU state and do
the lookup of the physical IRQ number when we are about to run the VCPU.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Now that the virtual arch timer does not care about the irq_phys_map
anymore, let's rework kvm_vgic_map_phys_irq() to return an error
value instead. Any reference to that mapping can later be done by
passing the correct combination of VCPU and virtual IRQ number.
This makes the irq_phys_map handling completely private to the
VGIC code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>

Now that the interface between the arch timer and the VGIC does not
require passing the irq_phys_map entry pointer anymore, let's remove
it from the virtual arch timer and use the virtual IRQ number instead
directly.
The remaining pointer returned by kvm_vgic_map_phys_irq() will be
removed in the following patch.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>

The communication of a Linux IRQ number from outside the VGIC to the
vgic was a leftover from the day when the vgic code cared about how a
particular device injects virtual interrupts mapped to a physical
interrupt.

We can safely remove this notion, leaving all physical IRQ handling to
be done in the device driver (the arch timer in this case), which makes
room for a saner API for the new VGIC.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>

kvm_vgic_unmap_phys_irq() only needs the virtual IRQ number, so let's
just pass that between the arch timer and the VGIC to get rid of
the irq_phys_map pointer.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>

For getting the active state of a mapped IRQ, we actually only need
the virtual IRQ number, not the pointer to the mapping entry.
Pass the virtual IRQ number from the arch timer to the VGIC directly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>

When we want to inject a hardware mapped IRQ into a guest, we actually
only need the virtual IRQ number from the irq_phys_map.
So let's pass this number directly from the arch timer to the VGIC
to avoid using the map as a parameter.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>

We actually don't use the irq_phys_map parameter in
vgic_update_irq_pending(), so let's just remove it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>

The EC field of the constructed ESR is conditionally modified by ORing in
ESR_ELx_EC_DABT_LOW for a data abort.  However, ESR_ELx_EC_SHIFT is missing
from this condition.
Signed-off-by: Matt Evans <matt.evans@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

The ARMv8.1 architecture extensions introduce support for hardware
updates of the access and dirty information in page table entries. With
VTCR_EL2.HA enabled (bit 21), when the CPU accesses an IPA with the
PTE_AF bit cleared in the stage 2 page table, instead of raising an
Access Flag fault to EL2 the CPU sets the actual page table entry bit
(10). To ensure that kernel modifications to the page table do not
inadvertently revert a bit set by hardware updates, certain Stage 2
software pte/pmd operations must be performed atomically.

The main user of the AF bit is the kvm_age_hva() mechanism. The
kvm_age_hva_handler() function performs a "test and clear young" action
on the pte/pmd. This needs to be atomic in respect of automatic hardware
updates of the AF bit. Since the AF bit is in the same position for both
Stage 1 and Stage 2, the patch reuses the existing
ptep_test_and_clear_young() functionality if
__HAVE_ARCH_PTEP_TEST_AND_CLEAR_YOUNG is defined. Otherwise, the
existing pte_young/pte_mkold mechanism is preserved.

The kvm_set_s2pte_readonly() (and the corresponding pmd equivalent) have
to perform atomic modifications in order to avoid a race with updates of
the AF bit. The arm64 implementation has been re-written using
exclusives.

Currently, kvm_set_s2pte_writable() (and pmd equivalent) take a pointer
argument and modify the pte/pmd in place. However, these functions are
only used on local variables rather than actual page table entries, so
it makes more sense to follow the pte_mkwrite() approach for stage 1
attributes. The change to kvm_s2pte_mkwrite() makes it clear that these
functions do not modify the actual page table entries.

The (pte|pmd)_mkyoung() uses on Stage 2 entries (setting the AF bit
explicitly) do not need to be modified since hardware updates of the
dirty status are not supported by KVM, so there is no possibility of
losing such information.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

The only call of arch_timer_get_timecounter (in KVM) has been removed.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Currently, the firmware tables are parsed 2 times: once in the GIC
drivers, the other time when initializing the vGIC. It means code
duplication and make more tedious to add the support for another
firmware table (like ACPI).

Use the recently introduced helper gic_get_kvm_info() to get
information about the virtual GIC.

With this change, the virtual GIC becomes agnostic to the firmware
table and KVM will be able to initialize the vGIC on ACPI.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

The firmware table is currently parsed by the virtual timer code in
order to retrieve the virtual timer interrupt. However, this is already
done by the arch timer driver.

To avoid code duplication, use the newly function arch_timer_get_kvm_info()
which return all the information required by the virtual timer code.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Fill up the recently introduced gic_kvm_info with the hardware
information used for virtualization.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

The ACPI code requires to use global variables in order to collect
information from the tables.

To make clear those variables are ACPI specific, gather all of them in a
single structure.

Furthermore, even if some of the variables are not marked with
__initdata, they are all only used during the initialization. Therefore,
the new variable, which hold the structure, can be marked with
__initdata.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Currently, most of the pr_* messages in the GICv3 driver don't have a
prefix.  Add one to make clear where the messages come from.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

For now, the firmware tables are parsed 2 times: once in the GIC
drivers, the other timer when initializing the vGIC. It means code
duplication and make more tedious to add the support for another
firmware table (like ACPI).

Introduce a new structure and set of helpers to get/set the virtual GIC
information. Also fill up the structure for GICv2.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

The ACPI code requires to use global variables in order to collect
information from the tables.

For now, a single global variable is used, but more will be added in a
subsequent patch. To make clear they are ACPI specific, gather all the
information in a single structure.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Acked-by: Christofer Dall <christoffer.dall@linaro.org>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Currently, the firmware table is parsed by the virtual timer code in
order to retrieve the virtual timer interrupt. However, this is already
done by the arch timer driver.

To avoid code duplication, extend arch_timer_kvm_info to get the virtual
IRQ.

Note that the KVM code will be modified in a subsequent patch.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Introduce a structure which are filled up by the arch timer driver and
used by the virtual timer in KVM.

The first member of this structure will be the timecounter. More members
will be added later.

A stub for the new helper isn't introduced because KVM requires the arch
timer for both ARM64 and ARM32.

The function arch_timer_get_timecounter is kept for the time being and
will be dropped in a subsequent patch.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

The ARM architecture mandates that when changing a page table entry
from a valid entry to another valid entry, an invalid entry is first
written, TLB invalidated, and only then the new entry being written.

The current code doesn't respect this, directly writing the new
entry and only then invalidating TLBs. Let's fix it up.

Cc: <stable@vger.kernel.org>
Reported-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Now that we can handle stage-2 page tables independent
of the host page table levels, wire up the 16K page
support.

Cc: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>

Now that we don't have any fake page table levels for arm64,
cleanup the common code to get rid of the dead code.

Cc: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>

On arm64, the hardware supports concatenation of upto 16 tables,
at entry level for stage2 translations and we make use that whenever
possible. This could lead to reduced number of translation levels than
the normal (stage1 table) table. Also, since the IPA(40bit) is smaller
than the some of the supported VA_BITS (e.g, 48bit), there could be
different number of levels in stage-1 vs stage-2 tables. To reuse the
kernel host page table walker for stage2 we have been using a fake
software page table level, not known to the hardware. But with 16K
translations, there could be upto 2 fake software levels (with 48bit VA
and 40bit IPA), which complicates the code. Hence, we want to get rid of
the hack.

Now that we have explicit accessors for hyp vs stage2 page tables,
define the stage2 walker helpers accordingly based on the actual
table used by the hardware.

Once we know the number of translation levels used by the hardware,
it is merely a job of defining the helpers based on whether a
particular level is folded or not, looking at the number of levels.

Some facts before we calculate the translation levels:

1) Smallest page size supported by arm64 is 4K.
2) The minimum number of bits resolved at any page table level
   is (PAGE_SHIFT - 3) at intermediate levels.
Both of them implies, minimum number of bits required for a level
change is 9.

Since we can concatenate upto 16 tables at stage2 entry, the total
number of page table levels used by the hardware for resolving N bits
is same as that for (N - 4) bits (with concatenation), as there cannot
be a level in between (N, N-4) as per the above rules.

Hence, we have

 STAGE2_PGTABLE_LEVELS = PGTABLE_LEVELS(KVM_PHYS_SHIFT - 4)

With the current IPA limit (40bit), for all supported translations
and VA_BITS, we have the following condition (even for 36bit VA with
16K page size):

 CONFIG_PGTABLE_LEVELS >= STAGE2_PGTABLE_LEVELS.

So, for e.g,  if PUD is present in stage2, it is present in the hyp(host).
Hence, we fall back to the host definition if we find that a level is not
folded. Otherwise we redefine it accordingly. A build time check is added
to make sure the above condition holds. If this condition breaks in future,
we can rearrange the host level helpers and fix our code easily.

Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>

Now that we have switched to explicit page table routines,
get rid of the obsolete kvm_* wrappers.

Also, kvm_tlb_flush_vmid_by_ipa is now called only on stage2
page tables, hence get rid of the redundant check.

Cc: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>

Now that the hyp page table is handled by different set of
routines, rename the original shared routines to stage2 handlers.
Also make explicit use of the stage2 page table helpers.

unmap_range has been merged to existing unmap_stage2_range.

Cc: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>

We have common routines to modify hyp and stage2 page tables
based on the 'kvm' parameter. For a smoother transition to
using separate routines for each, duplicate the routines
and modify the copy to work on hyp.

Marks the forked routines with _hyp_ and gets rid of the
kvm parameter which is no longer needed and is NULL for hyp.
Also, gets rid of calls to kvm_tlb_flush_by_vmid_ipa() calls
from the hyp versions. Uses explicit host page table accessors
instead of the kvm_* page table helpers.
Suggested-by: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>

We have stage2 page table helpers for both arm and arm64. Switch to
the stage2 helpers for routines that only deal with stage2 page table.

Cc: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>

Introduce hyp_pxx_table_empty helpers for checking whether
a given table entry is empty. This will be used explicitly
once we switch to explicit routines for hyp page table walk.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>

Introduce stage2 page table helpers for arm64. With the fake
page table level still in place, the stage2 table has the same
number of levels as that of the host (and hyp), so they all
fallback to the host version.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>

Introduce hyp_pxx_table_empty helpers for checking whether
a given table entry is empty. This will be used explicitly
once we switch to explicit routines for hyp page table walk.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Define the page table helpers for walking the stage2 pagetable
for arm. Since both hyp and stage2 have the same number of levels,
as that of the host we reuse the host helpers.

The exceptions are the p.d_addr_end routines which have to deal
with IPA > 32bit, hence we use the open coded version of their host helpers
which supports 64bit.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Get rid of kvm_pud_huge() which falls back to pud_huge. Use
pud_huge instead.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>

Both arm and arm64 now provides a helper, pmd_thp_or_huge()
to check if the given pmd represents a huge page. Use that
instead of our own custom check.
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>

Add a helper to determine if a given pmd represents a huge page
either by hugetlb or thp, as we have for arm. This will be used
by KVM MMU code.
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Steve Capper <steve.capper@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>

Rearrange the code for fake pgd handling, which is applicable
only for arm64. This will later be removed once we introduce
the stage2 page table walker macros.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>

We share most of the bits for VTCR_EL2 for different page sizes,
except for the TG0 value and the entry level value. This patch
makes the definitions a bit more cleaner to reflect this fact.

Also cleans up the VTTBR_X calculation. No functional changes.

Cc: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>

TCR_EL1, TCR_EL2 and VTCR_EL2, all share some field positions
(TG0, ORGN0, IRGN0 and SH0) and their corresponding value definitions.

This patch makes the TCR_EL1 definitions reusable and uses them for TCR_EL2
and VTCR_EL2 fields.

This also fixes a bug where we assume TG0 in {V}TCR_EL2 is 1bit field.

Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>

Commit 1e947bad ("arm64: KVM: Skip HYP setup when already running
in HYP") re-organized the hyp init code and ended up leaving the CPU
hotplug and PM notifier even if hyp mode initialization fails.

Since KVM is not yet supported with ACPI, the above mentioned commit
breaks CPU hotplug in ACPI boot.

This patch fixes teardown_hyp_mode to properly unregister both CPU
hotplug and PM notifiers in the teardown path.

Fixes: 1e947bad ("arm64: KVM: Skip HYP setup when already running in HYP")
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

We always thought that 40bits of PA range would be the minimum people
would actually build. Anything less is terrifyingly small.

Turns out that we were both right and wrong. Nobody has ever built
such a system, but the ARM Foundation Model has a PARange set to 36bits.
Just because we can. Oh well. Now, the KVM API explicitely says that
we offer a 40bit PA space to the VM, so we shouldn't run KVM on
the Foundation Model at all.

That being said, this patch offers a less agressive alternative, and
loudly warns about the configuration being unsupported. You'll still
be able to run VMs (at your own risks, though).

This is just a workaround until we have a proper userspace API where
we report the PARange to userspace.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>