This commit adds support for the GENETv5 implementation.

The GENETv5 reports a major version of 6 instead of 5 so compensate
for this when verifying the configuration of the driver.  Also the
EPHY revision is now contained in the MDIO registers of the PHY so
the EPHY revision of 0 in GENET_VER_FMT is expected for GENETv5.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The device tree documentation must be updated to reflect the new compatible
strings "brcm,genet-v5" and "brcm,genet-mdio-v5" used by the GENETv5 driver.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A third interrupt cell can be provided to optionally specify
the interrupt used for handling Wake on LAN events.

Typically the wake up handling uses a separate interrupt
controller, so the interrupts-extended property is used to
accommodate this.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit changes the ioctl handling behavior to return the
EOPNOTSUPP error code instead of the EINVAL error code when an
unknown ioctl command value is detected.

It also removes some redundant parsing of the ioctl command value
and allows the SIOCSHWTSTAMP value to be handled.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The reclaim function should return the number of buffer descriptors
reclaimed, not just the number corresponding to skb packets.

Also, remove the unnecessary computation when updating the consumer
index.

While this is not a functional problem it could degrade performance
of napi in a fragmented transmit stream.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the DMA interrupt status is latched and the DMA servicing can be
polled, it is a good idea to clear the latched status of a DMA interrupt
before performing the service that would be invoked by the interrupt.

This prevents old status from causing spurious interrupts when the
interrupt is unmasked at a later time.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bcmgenet_wol_isr() handler performs the necessary processing for
waking from a GENET event.  There is no necessary functionality behind
servicing the UMAC_IRQ_MPD_R event in the handling of isr0.  Therefore
the code that unmasks and masks this interrupt and that gets invoked
in response to it is removed by this commit.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit moves DMA interrupt enabling out of init_umac() and adds
the masking of these interrupts to the napi enable and disable code.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

An assortment of non-functional lines are removed to reduce confusion
and some typos in comments are corrected.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A 2's complement subtraction will always do a borrow, so masking
off the sign bits is the same as conditionally adding (mask+1).
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit adds support for the internal fast ethernet 10/100 PHY
found in the BCM7260, BCM7268, and BCM7271 devices.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The macros MDIO_AN_EEE_ADV_100TX and MDIO_AN_EEE_ADV_1000T are now
considered obsolete and are replaced in the kernel with the generic
macros MDIO_EEE_100TX and MDIO_EEE_1000T respectively.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrey reported this kernel warning:

WARNING: CPU: 0 PID: 4114 at kernel/sched/core.c:7737 __might_sleep+0x149/0x1a0
do not call blocking ops when !TASK_RUNNING; state=1 set at
[<ffffffff813fcb22>] prepare_to_wait+0x182/0x530

The deeply nested alloc_skb is a problem.

Diagnosis: nesting is wrong. It makes zero sense. Fix it and the
implicit task state change problem automagically goes away.

alloc_skb() does not need to be in the "while" loop.

alloc_skb() does not need to be in the {prepare_to_wait/add_wait_queue ...
finish_wait/remove_wait_queue} block.

I claim that:
- alloc_tx() should only perform the "wait_for_decent_tx_drain" part
- alloc_skb() ought to be done directly in vcc_sendmsg
- alloc_skb() failure can be handled gracefully in vcc_sendmsg
- alloc_skb() may use a (m->msg_flags & MSG_DONTWAIT) dependent
  GFP_{KERNEL / ATOMIC} flag
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-and-Tested-by: Chas Williams <3chas3@gmail.com>
Signed-off-by: Chas Williams <3chas3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch advances the qed* drivers into using the newer firmware -
This solves several firmware bugs, mostly related [but not limited to]
various init/deinit issues in various offloaded protocols.

It also introduces a major 4-Cached SGE change in firmware, which can be
seen in the storage drivers' changes.

In addition, this firmware is required for supporting the new QL41xxx
series of adapters; While this patch doesn't add the actual support,
the firmware contains the necessary initialization & firmware logic to
operate such adapters [actual support would be added later on].

Changes from Previous versions:
-------------------------------
 - V2 - fix kbuild-test robot warnings
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Robert Shearman says:

====================
mpls: allow TTL propagation from IP packets to be configured

Allow TTL propagation from IP packets to MPLS packets to be
configured. Add a new optional LWT attribute, MPLS_IPTUNNEL_TTL, which
allows the TTL to be set in the resulting MPLS packet, with the value
of 0 having the semantics of enabling propagation of the TTL from the
IP header (i.e. non-zero values disable propagation).

Also allow the configuration to be overridden globally by reusing the
same sysctl to control whether the TTL is propagated from IP packets
into the MPLS header. If the per-LWT attribute is set then it
overrides the global configuration. If the TTL isn't propagated then a
default TTL value is used which can be configured via a new sysctl,
"net.mpls.default_ttl". This is kept separate from the configuration
of whether IP TTL propagation is enabled as it can be used in the
future when non-IP payloads are supported (i.e. where there is no
payload TTL that can be propagated).
====================
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow TTL propagation from IP packets to MPLS packets to be
configured. Add a new optional LWT attribute, MPLS_IPTUNNEL_TTL, which
allows the TTL to be set in the resulting MPLS packet, with the value
of 0 having the semantics of enabling propagation of the TTL from the
IP header (i.e. non-zero values disable propagation).

Also allow the configuration to be overridden globally by reusing the
same sysctl to control whether the TTL is propagated from IP packets
into the MPLS header. If the per-LWT attribute is set then it
overrides the global configuration. If the TTL isn't propagated then a
default TTL value is used which can be configured via a new sysctl,
"net.mpls.default_ttl". This is kept separate from the configuration
of whether IP TTL propagation is enabled as it can be used in the
future when non-IP payloads are supported (i.e. where there is no
payload TTL that can be propagated).
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Provide the ability to control on a per-route basis whether the TTL
value from an MPLS packet is propagated to an IPv4/IPv6 packet when
the last label is popped as per the theoretical model in RFC 3443
through a new route attribute, RTA_TTL_PROPAGATE which can be 0 to
mean disable propagation and 1 to mean enable propagation.

In order to provide the ability to change the behaviour for packets
arriving with IPv4/IPv6 Explicit Null labels and to provide an easy
way for a user to change the behaviour for all existing routes without
having to reprogram them, a global knob is provided. This is done
through the addition of a new per-namespace sysctl,
"net.mpls.ip_ttl_propagate", which defaults to enabled. If the
per-route attribute is set (either enabled or disabled) then it
overrides the global configuration.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.

As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.

As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.

As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.

As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.

As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andreas Schultz says:

====================
gtp: misc improvements

This is a resent of last series that missed the merge window. There
are no changes compared to v4.

v4: Compared to v3 it contains mostly smallish naming and spelling fixes.
It also drops the documentation patch, Harald did a better job with the
documentation and the some things I described do not yet match the implementation.
I'll readd the relevant parts with a follow up series.

This series lays the groundwork for removing the socket references from
the GTP netdevice by removing duplicate code and simplifying the logic on
some code paths.

It slighly changes the GTP genl API by making the socket parameters optional
(though one of them is still required).

The removal of the socket references will break the 1:1 releation between
GTP netdevice and GTP socket that prevents us to support multiple VRFs with
overlapping IP addresse spaces attached to the same GTP-U entity (needed for
multi APN support, coming a follow up series).

Pablo found a socket hold problem in v2. In order to solve that I had to
switch the socket references from the struct socket to the internal
struct sock. This should have no functionl impact, but we can now hang
on to the reference without blocking user space from closing the GTP socket.

v4->v5:
 * resent for new merge window
v3->v4:
 * drop the documentation patch
 * spelling fixes
 * pass nlattr instead of genl_info into gtp_find_dev,
   makes the code slightly more compact and readable
v2->v3:
 * add documentation to explain the goal of all these changes
 * incorporate review comments
 * switch from struct socket to struct sock
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Having the socket present in context simplifies the sending logic.
It also fixes the invalid assumption that we have to use the same
sending socket for all client IP's on a specific gtp interface.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Consolidate duplicate code into helper.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This unifies duplicate code into a helper. It also prepares the
groundwork to add a lookup version that uses the socket to find
attached pdp contexts.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add network device to gtp context in preparation for splitting
the TEID from the network device.

Use this to rework the socker rx path. Move the common RX part
of v0 and v1 into a helper. Also move the final rx part into
that helper as well.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Both function are always used together with the final goal to
get the gtp_dev. This simplifies the code by merging them together.

The netdevice lookup is changed to use the regular dev_get_by_index.
The gtp netdevice list is now only used to find the PDP contexts for
imcomming packets. It can be completely eliminated Once the TEID
hash is moved into the GTP socket.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Having both GTPv0-U and GTPv1-U is not always desirable.
Fallback from GTPv1-U to GTPv0-U was depreciated from 3GPP
Rel-8 onwards. Post Rel-8 implementation are discuraged
from listening on the v0 port (see 3GPP TS 29.281, Sect. 1).

A future change will completely decouple the sockets from the
network device. Till then, at least one of the sockets needs to
be specified (either v0 or v1), the other is optional.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

After enabling the UDP encapsulation, only the sk member is used.

Holding the socket would prevent user space from closing the socket,
but holding a reference to the sk member does not have the same
effect.

This change will make it simpler to later detach the sockets from
the netdevice.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the rx queue default size when dma interrupts are treated,
since dma op mode can be also set there.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch configures default number of RX and TX queues when
using the pci glue driver.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes: 49b49971 ("net: sched: make default fifo qdiscs appear in the dump")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace init_timer with setup_timer to simplify the source code.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vivien Didelot says:

====================
net: dsa: mv88e6xxx: rework ATU support

The purpose of this patch series is to rework the code related to the
Address Translation Unit (ATU), and bring support for it to the 88E6390
family of switch chips.

All Global (1) ATU related code have been reworked and moved to its own
file. Some port related bits used for ATU configuration (such as the
Learn2All and MessagePort feature) have also been taken care of.

The ports' mode and egress flooding mode have been refactored to fix the
egress of frames with unknown unicast or multicast destination address,
and write all these bits regardless the port mode (Normal, DSA, etc.)

Finally remove the eth_addr_greater which was only used by mv88e6xxx.

Changes in v2:
  - add Reviewed-by tags
  - split mv88e6xxx_g1_atu_set_age_time and mv88e6xxx_atu_setup addition
  - remove DSA_TAG_PROTO_TRAILER check
  - split Message Port and Learn2All addition
  - remove unused MV88E6XXX_FLAG_G1_ATU_FID flag
  - add dsa_is_normal_port helper
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

eth_addr_greater() was introduced for the mv88e6xxx driver, but is not
used anymore. There is no other user, thus remove this function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new operation to disable the DA, SA and VTU priority override.

Setting such limit is not likely to be used soon, so provide a
port_disable_pri_override operation directly. This can be changed later
for port_set_pri_override when we'll need it.

Also remove the now obsolete mv88e6xxx_6320_family helper.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new operation to disable the limiting of learnt MAC addresses.

Setting such limit is not likely to be used soon, so provide a
port_disable_learn_limit operation directly. This can be changed later
for port_set_learn_limit when we'll need it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Marvell switch ports can be configured to allow or prevent egress of
frames with an unknown unicast or multicast destination address.

Some switch chips such as 88E6095 and 88E6185 have two disjoint bits in
Port Control Register (0x04) bit 2 "Forward Unknown" (for unicast) and
Port Control 2 Register (0x08) bit 6 "Default Forward" (for multicast).

Other chips such as 88E6085, 88E6123, 88E6352, and 88E6390 have a 2-bit
value in Port Control Register (0x04) bits 3:2 "EgressFloods".

The current code does not fully implement the disjoint bits variant and
assigns incorrect ones to some chip models. Fix that with two
implementation references (6185 and 6352 that I currently have) of a
port_set_egress_floods operation (as named in datasheets).

Old chips such as 88E6060 don't have egress flooding mode, so don't
error out if the operation is not provided.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>