imx_shutdown() calls imx_disable_dma if .dma_is_enabled. So after
imx_shudown() completes, .dma_is_enabled is zero. For this reason
.dma_is_enabled is also zero when imx_startup() is called. So the check
for this variable being zero can be dropped.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The .dma_is_inited member is only set to a value != 0 when the port's
startup function calls imx_uart_dma_init(). On shutdown of the port
imx_uart_dma_exit is called which sets the value back to 0. So
.dma_is_inited is always 0 when imx_startup() is called (assuming
.startup() and .shutdown() are correctly balanced) and the check for
!sport->dma_is_inited can go away.

This allows to replace .dma_is_inited by a variable local to
imx_startup.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Handling an irq that isn't enabled can have some undesired side effects.
Some of these are mentioned in the newly introduced code comment. Some
of the irq sources already had their handling right, some don't. Handle
them all in the same consistent way.

The change for USR1_RRDY and USR1_AGTIM drops the check for
dma_is_enabled. This is correct as UCR1_RRDYEN and UCR2_ATEN are always
off if dma is enabled.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now the variable holding the value of register USR1 is called usr1
instead of sts which is more straight forward. The same is also done for
sts2 which is called usr2 now.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The check sts & USR1_DTRD was just evaluated to true two lines above.
So this change doesn't have any effect on the semantic of the driver.

Fixes: 27e16501 ("serial: imx: implement DSR irq handling for DTE mode")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bit pattern STAT_FRM_ERR is being bit-wise or'd twice; remove the
redundant 2nd STAT_FRM_ERR
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This allows me to login after sending a break when service
serial-getty@ttymxc0.service is running

The "tty_insert_flip_char(port, 0, TTY_BREAK)" in clear_rx_errors
fixes this by allowing the higher layers to see a break.

Also, call uart_handle_break to handle possible
"secure attention key."

FYI: Martin said the ROM sdma firmware works with this patch,
but external sdma firmware still does not send breaks on a
i.mx6UL
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: Martin Hicks <mort@bork.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

An issue has been observed on the Marvell Armada 38x serial port.

Writes to UART_LCR can result in characters that are currently held in the
TX FIFO being lost rather than sent, even if the userspace process has
attempted to flush them.

This is most visible when using the "resize" command (tested on Busybox),
where we have observed the escape code for restoring cursor position
becoming mangled.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

High latencies of classic timers cause performance issues for high-
speed serial transmissions. This patch transforms rx_timer into an
hrtimer to reduce the minimum latency.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

omap_8250_throttle() is called when tty RX buffer is about to overflow
and can no longer keep up with the rate at which UART is receiving data.
So, the expectation of this callback, is that UART stops RX and asserts
HW flow control to signal the sender to stop sending more data.
omap_8250_throttle() disables RX FIFO interrupts thus FIFO is no longer
serviced, leading to assertion of flow control once RX FIFO is full.
But, this does not work when DMA is enabled as driver keeps queuing new
RX DMA request in completion handler without brothering about throttling
request made by the higher layer.
This patch introduces a flag that can be used to determine whether or
not to queue next RX DMA request based on throttling request.

Without this patch, tty buffer overflows are reported at higher
baudrates.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently, data in RX FIFO is read based on UART_LSR register state even
if RDI and RLSI interrupts are disabled in UART_IER register.
This is because when IRQ handler is called due to TX FIFO empty event,
RX FIFO is serviced based on UART_LSR register status instead of
UART_IIR status. This defeats the purpose of disabling UART RX
FIFO interrupts during throttling(see, omap_8250_throttle()) as IRQ
handler continues to drain UART RX FIFO resulting in overflow of buffer
at tty layer.
Fix this by making sure that driver drains UART RX FIFO only when
UART_IIR_RDI is set along with UART_LSR_BI or UART_LSR_DR bits.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

R-Car V3H (R8A77980) SoC has the R-Car gen3 compatible SCIF and HSCIF ports,
so document the SoC specific bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some debugging tools (/sys/kernel/debug/gpio, `lsgpio`) use the
gpio_chip's label for displaying an additional context. Right now, the
information duplicates stuff which is already available from the
parent's device. This is how e.g. `lsgpio`'s output looks like:

  GPIO chip: gpiochip2, "spi1.2", 16 GPIO lines

Comparing the output of other GPIO expanders that I have available:

  gpiochip4: GPIOs 464-479, parent: spi/spi1.1, mcp23s17, can sleep:
  gpiochip5: GPIOs 448-463, parent: i2c/0-0020, pca9555, can sleep:
  gpiochip2: GPIOs 496-511, parent: spi/spi1.2, spi1.2, can sleep:

This patch ensures that the type of the real HW device is shown instead
of duplicating the SPI path:

  gpiochip2: GPIOs 496-511, parent: spi/spi1.2, MAX14830, can sleep:
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The UART can be operated without an irq. In this case a timer is setup
that regularily calls altera_uart_interrupt(). The receiving part
depends on pp->imr having the bit ALTERA_UART_STATUS_RRDY_MSK set,
otherwise altera_uart_rx_chars() is never called. So ensure that the bit
gets set (disguised as ALTERA_UART_CONTROL_RRDY_MSK) by not returning
early from altera_uart_startup() if port->irq is 0.

This doesn't affect the hardware as the ALTERA_UART_CONTROL_RRDY_MSK bit
isn't actually written to the control register.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the irq line of an altera UART device isn't used to report interrupts
for this device the driver better ensures that this device doesn't pull
this line to active state and so disturb the whatever might be connected
to this line.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Most register accesses in the altera driver honor port->regshift by
using altera_uart_writel(). There are a few accesses however that were
missed when the driver was converted to use port->regshift and some
others were added later in commit 4d9d7d89 ("serial: altera_uart:
add earlycon support").

Fixes: 2780ad42 ("tty: serial: altera_uart: Use port->regshift to store bus shift")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 4fe505119778 ("console: Expand dummy functions for CFI") accidentally
added "static" to newport_con instance of struct consw, while trying to
normalize the declarations. This, however, needed to stay non-static as it
has an extern.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 4fe505119778 ("console: Expand dummy functions for CFI")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This expands the no-op dummy functions into full prototypes to avoid
indirect call mismatches when running under Control Flow Integrity
checking, like with Clang's -fsanitize=cfi.
Co-Developed-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Reading the function declarations for the console callbacks lacks any
hints as to what the arguments are. Instead of going and digging around in
various implementations that may each only have a subset of the callbacks,
name all the arguments in the declaration. This has no functional change.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As done in commit:

  724ba8b3 ("console/dummy: leave .con_font_get set to NULL")

This drops the dummy .con_font_get(), as it could leave arguments
uninitialized.

Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull Xtensa fixes from Max Filippov:
 "Two fixes for reserved memory/DMA buffers allocation in high memory on
  xtensa architecture

   - fix memory accounting when reserved memory is in high memory region

   - fix DMA allocation from high memory"

* tag 'xtensa-20180225' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: support DMA buffers in high memory
  xtensa: fix high memory/reserved memory collision

Pull x86 fixes from Thomas Gleixner:
 "A small set of fixes:

   - UAPI data type correction for hyperv

   - correct the cpu cores field in /proc/cpuinfo on CPU hotplug

   - return proper error code in the resctrl file system failure path to
     avoid silent subsequent failures

   - correct a subtle accounting issue in the new vector allocation code
     which went unnoticed for a while and caused suspend/resume
     failures"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/topology: Update the 'cpu cores' field in /proc/cpuinfo correctly across CPU hotplug operations
  x86/topology: Fix function name in documentation
  x86/intel_rdt: Fix incorrect returned value when creating rdgroup sub-directory in resctrl file system
  x86/apic/vector: Handle vector release on CPU unplug correctly
  genirq/matrix: Handle CPU offlining proper
  x86/headers/UAPI: Use __u64 instead of u64 in <uapi/asm/hyperv.h>

Pull perf fix from Thomas Gleixner:
 "A single commit which shuts up a bogus GCC-8 warning"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/oprofile: Fix bogus GCC-8 warning in nmi_setup()

Pull locking fixes from Thomas Gleixner:
 "Three patches to fix memory ordering issues on ALPHA and a comment to
  clarify the usage scope of a mutex internal function"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/xchg/alpha: Fix xchg() and cmpxchg() memory ordering bugs
  locking/xchg/alpha: Clean up barrier usage by using smp_mb() in place of __ASM__MB
  locking/xchg/alpha: Add unconditional memory barrier to cmpxchg()
  locking/mutex: Add comment to __mutex_owner() to deter usage

Pull cleanup patchlet from Thomas Gleixner:
 "A single commit removing a bunch of bogus double semicolons all over
  the tree"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  treewide/trivial: Remove ';;$' typo noise

Pull NFS client bugfixes from Trond Myklebust:

 - fix a broken cast in nfs4_callback_recallany()

 - fix an Oops during NFSv4 migration events

 - make struct nlmclnt_fl_close_lock_ops static

* tag 'nfs-for-4.16-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFS: make struct nlmclnt_fl_close_lock_ops static
  nfs: system crashes after NFS4ERR_MOVED recovery
  NFSv4: Fix broken cast in nfs4_callback_recallany()

Pull powerpc fixes from Michael Ellerman:

 - Add handling for a missing instruction in our 32-bit BPF JIT so that
   it can be used for seccomp filtering.

 - Add a missing NULL pointer check before a function call in new EEH
   code.

 - Fix an error path in the new ocxl driver to correctly return EFAULT.

 - The support for the new ibm,drc-info device tree property turns out
   to need several fixes, so for now we just stop advertising to
   firmware that we support it until the bugs can be ironed out.

 - One fix for the new drmem code which was incorrectly modifying the
   device tree in place.

 - Finally two fixes for the RFI flush support, so that firmware can
   advertise to us that it should be disabled entirely so as not to
   affect performance.

Thanks to: Bharata B Rao, Frederic Barrat, Juan J. Alvarez, Mark Lord,
Michael Bringmann.

* tag 'powerpc-4.16-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/powernv: Support firmware disable of RFI flush
  powerpc/pseries: Support firmware disable of RFI flush
  powerpc/mm/drmem: Fix unexpected flag value in ibm,dynamic-memory-v2
  powerpc/bpf/jit: Fix 32-bit JIT for seccomp_data access
  powerpc/pseries: Revert support for ibm,drc-info devtree property
  powerpc/pseries: Fix duplicate firmware feature for DRC_INFO
  ocxl: Fix potential bad errno on irq allocation
  powerpc/eeh: Fix crashes in eeh_report_resume()

Pull networking fixes from David Miller:

 1) Fix TTL offset calculation in mac80211 mesh code, from Peter Oh.

 2) Fix races with procfs in ipt_CLUSTERIP, from Cong Wang.

 3) Memory leak fix in lpm_trie BPF map code, from Yonghong Song.

 4) Need to use GFP_ATOMIC in BPF cpumap allocations, from Jason Wang.

 5) Fix potential deadlocks in netfilter getsockopt() code paths, from
    Paolo Abeni.

 6) Netfilter stackpointer size checks really are needed to validate
    user input, from Florian Westphal.

 7) Missing timer init in x_tables, from Paolo Abeni.

 8) Don't use WQ_MEM_RECLAIM in mac80211 hwsim, from Johannes Berg.

 9) When an ibmvnic device is brought down then back up again, it can be
    sent queue entries from a previous session, handle this properly
    instead of crashing. From Thomas Falcon.

10) Fix TCP checksum on LRO buffers in mlx5e, from Gal Pressman.

11) When we are dumping filters in cls_api, the output SKB is empty, and
    the filter we are dumping is too large for the space in the SKB, we
    should return -EMSGSIZE like other netlink dump operations do.
    Otherwise userland has no signal that is needs to increase the size
    of its read buffer. From Roman Kapl.

12) Several XDP fixes for virtio_net, from Jesper Dangaard Brouer.

13) Module refcount leak in netlink when a dump start fails, from Jason
    Donenfeld.

14) Handle sub-optimal GSO sizes better in TCP BBR congestion control,
    from Eric Dumazet.

15) Releasing bpf per-cpu arraymaps can take a long time, add a
    condtional scheduling point. From Eric Dumazet.

16) Implement retpolines for tail calls in x64 and arm64 bpf JITs. From
    Daniel Borkmann.

17) Fix page leak in gianfar driver, from Andy Spencer.

18) Missed clearing of estimator scratch buffer, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
  net_sched: gen_estimator: fix broken estimators based on percpu stats
  gianfar: simplify FCS handling and fix memory leak
  ipv6 sit: work around bogus gcc-8 -Wrestrict warning
  macvlan: fix use-after-free in macvlan_common_newlink()
  bpf, arm64: fix out of bounds access in tail call
  bpf, x64: implement retpoline for tail call
  rxrpc: Fix send in rxrpc_send_data_packet()
  net: aquantia: Fix error handling in aq_pci_probe()
  bpf: fix rcu lockdep warning for lpm_trie map_free callback
  bpf: add schedule points in percpu arrays management
  regulatory: add NUL to request alpha2
  ibmvnic: Fix early release of login buffer
  net/smc9194: Remove bogus CONFIG_MAC reference
  net: ipv4: Set addr_type in hash_keys for forwarded case
  tcp_bbr: better deal with suboptimal GSO
  smsc75xx: fix smsc75xx_set_features()
  netlink: put module reference if dump start fails
  selftests/bpf/test_maps: exit child process without error in ENOMEM case
  selftests/bpf: update gitignore with test_libbpf_open
  selftests/bpf: tcpbpf_kern: use in6_* macros from glibc
  ..

Merge branch 'fixes-v4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security

Pull security subsystem fixes from James Morris:

 - keys fixes via David Howells:
      "A collection of fixes for Linux keyrings, mostly thanks to Eric
       Biggers:

        - Fix some PKCS#7 verification issues.

        - Fix handling of unsupported crypto in X.509.

        - Fix too-large allocation in big_key"

 - Seccomp updates via Kees Cook:
      "These are fixes for the get_metadata interface that landed during
       -rc1. While the new selftest is strictly not a bug fix, I think
       it's in the same spirit of avoiding bugs"

 - an IMA build fix from Randy Dunlap

* 'fixes-v4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  integrity/security: fix digsig.c build error with header file
  KEYS: Use individual pages in big_key for crypto buffers
  X.509: fix NULL dereference when restricting key with unsupported_sig
  X.509: fix BUG_ON() when hash algorithm is unsupported
  PKCS#7: fix direct verification of SignerInfo signature
  PKCS#7: fix certificate blacklisting
  PKCS#7: fix certificate chain verification
  seccomp: add a selftest for get_metadata
  ptrace, seccomp: tweak get_metadata behavior slightly
  seccomp, ptrace: switch get_metadata types to arch independent

Pull arm64 fixes from Catalin Marinas:
 "arm64 and perf fixes:

   - build error when accessing MPIDR_HWID_BITMASK from .S

   - fix CTR_EL0 field definitions

   - remove/disable some kernel messages on user faults (unhandled
     signals, unimplemented syscalls)

   - fix kernel page fault in unwind_frame() with function graph tracing

   - fix perf sleeping while atomic errors when booting with ACPI"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: fix unwind_frame() for filtered out fn for function graph tracing
  arm64: Enforce BBM for huge IO/VMAP mappings
  arm64: perf: correct PMUVer probing
  arm_pmu: acpi: request IRQs up-front
  arm_pmu: note IRQs and PMUs per-cpu
  arm_pmu: explicitly enable/disable SPIs at hotplug
  arm_pmu: acpi: check for mismatched PPIs
  arm_pmu: add armpmu_alloc_atomic()
  arm_pmu: fold platform helpers into platform code
  arm_pmu: kill arm_pmu_platdata
  ARM: ux500: remove PMU IRQ bouncer
  arm64: __show_regs: Only resolve kernel symbols when running at EL1
  arm64: Remove unimplemented syscall log message
  arm64: Disable unhandled signal log messages by default
  arm64: cpufeature: Fix CTR_EL0 field definitions
  arm64: uaccess: Formalise types for access_ok()
  arm64: Fix compilation error while accessing MPIDR_HWID_BITMASK from .S files

Pull MIPS fix from James Hogan:
 "A single MIPS fix for mismatching struct compat_flock, resulting in
  bus errors starting Firefox on Debian 8 since 4.13"

* tag 'mips_fixes_4.16_3' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
  MIPS: Drop spurious __unused in struct compat_flock

Pull printk fixlet from Petr Mladek:
 "People expect to see the real pointer value for %px.

  Let's substitute '(null)' only for the other %p? format modifiers that
  need to deference the pointer"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
  vsprintf: avoid misleading "(null)" for %px

Pull i2c fixes from Wolfram Sang:
 "Two bugfixes, one v4.16 regression fix, and two documentation fixes"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: designware: Consider SCL GPIO optional
  i2c: busses: i2c-sirf: Fix spelling: "formular" -> "formula".
  i2c: bcm2835: Set up the rising/falling edge delays
  i2c: i801: Add missing documentation entries for Braswell and Kaby Lake
  i2c: designware: must wait for enable

Pull SCSI fixes from James Bottomley:
 "These are mostly fixes for problems with merge window code.

  In addition we have one doc update (alua) and two dead code removals
  (aiclib and octogon) a spurious assignment removal (csiostor) and a
  performance improvement for storvsc involving better interrupt
  spreading and increasing the command per lun handling"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: qla4xxx: skip error recovery in case of register disconnect.
  scsi: aacraid: fix shutdown crash when init fails
  scsi: qedi: Cleanup local str variable
  scsi: qedi: Fix truncation of CHAP name and secret
  scsi: qla2xxx: Fix incorrect handle for abort IOCB
  scsi: qla2xxx: Fix double free bug after firmware timeout
  scsi: storvsc: Increase cmd_per_lun for higher speed devices
  scsi: qla2xxx: Fix a locking imbalance in qlt_24xx_handle_els()
  scsi: scsi_dh: Document alua_rtpg_queue() arguments
  scsi: Remove Makefile entry for oktagon files
  scsi: aic7xxx: remove aiclib.c
  scsi: qla2xxx: Avoid triggering undefined behavior in qla2x00_mbx_completion()
  scsi: mptfusion: Add bounds check in mptctl_hp_targetinfo()
  scsi: sym53c8xx_2: iterator underflow in sym_getsync()
  scsi: bnx2fc: Fix check in SCSI completion handler for timed out request
  scsi: csiostor: remove redundant assignment to pointer 'ln'
  scsi: ufs: Enable quirk to ignore sending WRITE_SAME command
  scsi: ibmvfc: fix misdefined reserved field in ibmvfc_fcp_rsp_info
  scsi: qla2xxx: Fix memory corruption during hba reset test
  scsi: mpt3sas: fix an out of bound write

Pull drm fixes from Dave Airlie:
 "A bunch of fixes for rc3:

  Exynos:
   - fixes for using monotonic timestamps
   - register definitions
   - removal of unused file

  ipu-v3L
   - minor changes
   - make some register arrays const+static
   - fix some leaks

  meson:
   - fix for vsync

  atomic:
   - fix for memory leak

  EDID parser:
   - add quirks for some more non-desktop devices
   - 6-bit panel fix.

  drm_mm:
   - fix a bug in the core drm mm hole handling

  cirrus:
   - fix lut loading regression

  Lastly there is a deadlock fix around runtime suspend for secondary
  GPUs.

  There was a deadlock between one thread trying to wait for a workqueue
  job to finish in the runtime suspend path, and the workqueue job it
  was waiting for in turn waiting for a runtime_get_sync to return.

  The fixes avoids it by not doing the runtime sync in the workqueue as
  then we always wait for all those tasks to complete before we runtime
  suspend"

* tag 'drm-fixes-for-v4.16-rc3' of git://people.freedesktop.org/~airlied/linux: (25 commits)
  drm/tve200: fix kernel-doc documentation comment include
  drm/edid: quirk Sony PlayStation VR headset as non-desktop
  drm/edid: quirk Windows Mixed Reality headsets as non-desktop
  drm/edid: quirk Oculus Rift headsets as non-desktop
  drm/meson: fix vsync buffer update
  drm: Handle unexpected holes in color-eviction
  drm: exynos: Use proper macro definition for HDMI_I2S_PIN_SEL_1
  drm/exynos: remove exynos_drm_rotator.h
  drm/exynos: g2d: Delete an error message for a failed memory allocation in two functions
  drm/exynos: fix comparison to bitshift when dealing with a mask
  drm/exynos: g2d: use monotonic timestamps
  drm/edid: Add 6 bpc quirk for CPT panel in Asus UX303LA
  gpu: ipu-csi: add 10/12-bit grayscale support to mbus_code_to_bus_cfg
  gpu: ipu-cpmem: add 16-bit grayscale support to ipu_cpmem_set_image
  gpu: ipu-v3: prg: fix device node leak in ipu_prg_lookup_by_phandle
  gpu: ipu-v3: pre: fix device node leak in ipu_pre_lookup_by_phandle
  drm/amdgpu: Fix deadlock on runtime suspend
  drm/radeon: Fix deadlock on runtime suspend
  drm/nouveau: Fix deadlock on runtime suspend
  drm: Allow determining if current task is output poll worker
  ...

pfifo_fast got percpu stats lately, uncovering a bug I introduced last
year in linux-4.10.

I missed the fact that we have to clear our temporary storage
before calling __gnet_stats_copy_basic() in the case of percpu stats.

Without this fix, rate estimators (tc qd replace dev xxx root est 1sec
4sec pfifo_fast) are utterly broken.

Fixes: 1c0d32fd ("net_sched: gen_estimator: complete rewrite of rate estimators")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf 2018-02-22

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) two urgent fixes for bpf_tail_call logic for x64 and arm64 JITs, from Daniel.

2) cond_resched points in percpu array alloc/free paths, from Eric.

3) lockdep and other minor fixes, from Yonghong, Arnd, Anders, Li.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously, buffer descriptors containing only the frame check sequence
(FCS) were skipped and not added to the skb. However, the page reference
count was still incremented, leading to a memory leak.

Fixing this inside gfar_add_rx_frag() is difficult due to reserved
memory handling and page reuse. Instead, move the FCS handling to
gfar_process_frame() and trim off the FCS before passing the skb up the
networking stack.
Signed-off-by: Andy Spencer <aspencer@spacex.com>
Signed-off-by: Jim Gruen <jgruen@spacex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gcc-8 has a new warning that detects overlapping input and output arguments
in memcpy(). It triggers for sit_init_net() calling ipip6_tunnel_clone_6rd(),
which is actually correct:

net/ipv6/sit.c: In function 'sit_init_net':
net/ipv6/sit.c:192:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]

The problem here is that the logic detecting the memcpy() arguments finds them
to be the same, but the conditional that tests for the input and output of
ipip6_tunnel_clone_6rd() to be identical is not a compile-time constant.

We know that netdev_priv(t->dev) is the same as t for a tunnel device,
and comparing "dev" directly here lets the compiler figure out as well
that 'dev == sitn->fb_tunnel_dev' when called from sit_init_net(), so
it no longer warns.

This code is old, so Cc stable to make sure that we don't get the warning
for older kernels built with new gcc.

Cc: Martin Sebor <msebor@gmail.com>
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=83456Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>