Currently, POWER and BYPASS bits are set up in a single write to pllv3
register.  This causes problem occasionally from the IPU/HDMI testing.
Let's follow FSL BSP code to set up POWER bit, relock, and then BYPASS
sequentially.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The pllv3 nees relock not only when powering up but also when rate
changes.  The patch creates a helper function clk_pllv3_wait_lock() and
moves the relock code from clk_pllv3_prepare() into there, so that
both .prepare() and .set_rate() hooks of pllv3 can call into the helper
for relocking.

Since relock is only needed when PLL is powered up while clk_set_rate()
could be called before clk is prepared, we need to add a check in
clk_pllv3_wait_lock() to skip the relock if PLL is not powered.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The pllv3 relock time varies in the range of 50us ~ 500us, depending on
the specific PLL type, e.g. 50us for ARM PLL and 450us for Audio/Video
PLL.  Let's add a usleep_range() call instead of doing busy wait during
relock.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The clk_enet_ref_table[] is missing a final empty entry as end of list
marker. Also make the existing markers more obvious.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Building a kernel with the following options,

  CONFIG_SMP=n
  CONFIG_PM=y
  CONFIG_SOC_IMX6SL=y
  CONFIG_SOC_IMX6Q=n

we will see the build error below.

  arch/arm/mach-imx/built-in.o: In function `imx6q_pm_enter':
  platform-spi_imx.c:(.text+0x2648): undefined reference to `v7_cpu_resume'
  make[1]: *** [vmlinux] Error 1

This is because that v7_cpu_resume() implemented in headsmp.S is also
needed by imx6sl build.  Let's build headsmp.S for CONFIG_SOC_IMX6SL as
well.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The current comment in the code does not make it clear why the double writes
on SRC bit is needed.  Let's quote the errata to get it clear.  Also, to
ensure there are at least 2 writes happen in the same one 32kHz period,
we actually need 3 writes.  Let's add the third one.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

There is ~10% possibility that the following emergency restart command
fails to reboot imx6q.

$ echo b > /proc/sysrq-trigger

The IMX restart routine mxc_restart() assumes that it will always run on
primary core, and will call imx_src_prepare_restart() to disable
secondary cores in order to get them come to online in the following
boot.  However, the assumption is only true for normal kernel_restart()
case where migrate_to_reboot_cpu() will be called to migrate to primary
core, but not necessarily true for emergency_restart() case.  So when
emergency_restart() calls into mxc_restart() on any secondary core,
system will hang immediately once imx_src_prepare_restart() is called
to disabled secondary cores.  Since emergency_restart() is defined as a
function that is safe to call in interrupt context, we cannot just call
migrate_to_reboot_cpu() to fix the issue.

Fortunately, we just found that the issue can be fixed at imx6q platform
level.  We used to call imx_src_prepare_restart() to disable all
secondary cores before resetting hardware.  Otherwise, the secondary
will fail come to online in the reboot.  However, we recently found that
after commit 6050d181 (ARM: imx: reset core along with enable/disable
operation) comes to play, we do not need to reset the secondary cores
any more.  That said, mxc_restart() now can run on any core to reboot
the system, as long as we remove the imx_src_prepare_restart() call from
mxc_restart().

So let's simply remove imx_src_prepare_restart() call to fix the above
emergency restart failure.
Reported-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

instead of pll3_usb_otg the parent of can_root clock
should be pll3_60m.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Pull ARC changes from Vineet Gupta:
 - Towards a working SMP setup (ASID allocation, TLB Flush,...)
 - Support for TRACE_IRQFLAGS, LOCKDEP
 - cacheflush backend consolidation for I/D
 - Lots of allmodconfig fixlets from Chen
 - Other improvements/fixes

* tag 'arc-v3.13-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (25 commits)
  ARC: [plat-arcfpga] defconfig update
  smp, ARC: kill SMP single function call interrupt
  ARC: [SMP] Disallow RTSC
  ARC: [SMP] Fix build failures for large NR_CPUS
  ARC: [SMP] enlarge possible NR_CPUS
  ARC: [SMP] TLB flush
  ARC: [SMP] ASID allocation
  arc: export symbol for pm_power_off in reset.c
  arc: export symbol for save_stack_trace() in stacktrace.c
  arc: remove '__init' for get_hw_config_num_irq()
  arc: remove '__init' for first_lines_of_secondary()
  arc: remove '__init' for setup_processor() and arc_init_IRQ()
  arc: kgdb: add default implementation for kgdb_roundup_cpus()
  ARC: Fix bogus gcc warning and micro-optimise TLB iteration loop
  ARC: Add support for irqflags tracing and lockdep
  ARC: Reset the value of Interrupt Priority Register
  ARC: Reduce #ifdef'ery for unaligned access emulation
  ARC: Change calling convention of do_page_fault()
  ARC: cacheflush optim - PTAG can be loop invariant if V-P is const
  ARC: cacheflush refactor #3: Unify the {d,i}cache flush leaf helpers
  ...

Pull m68k updates from Geert Uytterhoeven:
 "Summary:
   - __put_user_unaligned may/will be used by btrfs
   - m68k part of a global cleanup"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Remove deprecated IRQF_DISABLED
  m68k/m68knommu: Implement __get_user_unaligned/__put_user_unaligned()

Pull parisc update from Helge Deller:
 - a bugfix for sticon (parisc text console driver) to not crash the
   64bit kernel on machines with more than 4GB RAM
 - added kernel audit support
 - made udelay() implementation SMP-safe
 - "make install" now does not depend on vmlinux
 - added defconfigs for 32- and 64-kernels

* 'parisc-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: add generic 32- and 64-bit defconfigs
  parisc: sticon - unbreak on 64bit kernel
  parisc: signal fixup - SIGBUS vs. SIGSEGV
  parisc: implement full version of access_ok()
  parisc: correctly display number of active CPUs
  parisc: do not count IPI calls twice
  parisc: make udelay() SMP-safe
  parisc: remove duplicate define
  parisc: make "make install" not depend on vmlinux
  parisc: add kernel audit feature
  parisc: provide macro to create exception table entries

Pull ARM SoC DT updates from Olof Johansson:
 "Most of this branch consists of updates, additions and general churn
  of the device tree source files in the kernel (arch/arm/boot/dts).
  Besides that, there are a few things to point out:

   - Lots of platform conversion on OMAP2+, with removal of old board
     files for various platforms.
   - Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
     well
   - Some updates to pinctrl and other subsystems.  Most of these are
     for DT-enablement of the various platforms and acks have been
     collected"

* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
  ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
  ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
  ARM: dts: bcm281xx: Add card detect GPIO
  ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
  ARM: bcm281xx: Add device node for the GPIO controller
  ARM: mvebu: Add Netgear ReadyNAS 104 board
  ARM: tegra: fix Tegra114 IOMMU register address
  ARM: kirkwood: add support for OpenBlocks A7 platform
  ARM: dts: omap4-panda: add DPI pinmuxing
  ARM: dts: AM33xx: Add RNG node
  ARM: dts: AM33XX: Add hwspinlock node
  ARM: dts: OMAP5: Add hwspinlock node
  ARM: dts: OMAP4: Add hwspinlock node
  ARM: dts: use 'status' property for PCIe nodes
  ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
  ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
  ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
  ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
  ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
  ARM: mvebu: Add the core-divider clock to Armada 370/XP
  ...

Pull ARM driver updates from Olof Johansson:
 "Updates of SoC-near drivers and other driver updates that makes more
  sense to take through our tree.  In this case it's involved:

   - Some Davinci driver updates that has required corresponding
     platform code changes (gpio mostly)
   - CCI bindings and a few driver updates
   - Marvell mvebu patches for PCI MSI support (could have gone through
     the PCI tree for this release, but they were acked by Bjorn for
     3.12 so we kept them through arm-soc).
   - Marvell dove switch-over to DT-based PCIe configuration
   - Misc updates for Samsung platform dmaengine drivers"

* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
  ARM: S3C24XX: add dma pdata for s3c2410, s3c2440 and s3c2442
  dmaengine: s3c24xx-dma: add support for the s3c2410 type of controller
  ARM: S3C24XX: Fix possible dma selection warning
  PCI: mvebu: make local functions static
  PCI: mvebu: add I/O access wrappers
  PCI: mvebu: Dynamically detect if the PEX link is up to enable hot plug
  ARM: mvebu: fix gated clock documentation
  ARM: dove: remove legacy pcie and clock init
  ARM: dove: switch to DT probed mbus address windows
  ARM: SAMSUNG: set s3c24xx_dma_filter for s3c64xx-spi0 device
  ARM: S3C24XX: add platform-devices for new dma driver for s3c2412 and s3c2443
  dmaengine: add driver for Samsung s3c24xx SoCs
  ARM: S3C24XX: number the dma clocks
  PCI: mvebu: add support for Marvell Dove SoCs
  PCI: mvebu: add support for reset on GPIO
  PCI: mvebu: remove subsys_initcall
  PCI: mvebu: increment nports only for registered ports
  PCI: mvebu: move clock enable before register access
  PCI: mvebu: add support for MSI
  irqchip: armada-370-xp: implement MSI support
  ...

Pull ARM SoC board updates from Olof Johansson:
 "Board-related updates.  This branch is getting smaller and smaller,
  which is the whole idea so that's reassuring.

  Right now by far most of the code is related to shmobile updates, and
  they are now switching over to removal of board code and migration to
  multiplatform, so we'll see their board code base shrink in the near
  future too, I hope.

  In addition to that is some defconfig updates, some display updates
  for OMAP and a bit of new board support for Rockchip boards"

* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (56 commits)
  ARM: rockchip: add support for rk3188 and Radxa Rock board
  ARM: rockchip: add dts for bqcurie2 tablet
  ARM: rockchip: enable arm-global-timer
  ARM: rockchip: move shared dt properties to common source file
  ARM: OMAP2+: display: Create omap_vout device inside omap_display_init
  ARM: OMAP2+: display: Create omapvrfb and omapfb devices inside omap_display_init
  ARM: OMAP2+: display: Create omapdrm device inside omap_display_init
  ARM: OMAP2+: drm: Don't build device for DMM
  ARM: tegra: defconfig updates
  RX-51: Add support for OMAP3 ROM Random Number Generator
  ARM: OMAP3: RX-51: ARM errata 430973 workaround
  ARM: OMAP3: Add secure function omap_smc3() which calling instruction smc #1
  ARM: shmobile: marzen: enable INTC IRQ
  ARM: shmobile: bockw: add SMSC support on reference
  ARM: shmobile: Use SMP on Koelsch
  ARM: shmobile: Remove KZM9D reference DTS
  ARM: shmobile: Let KZM9D multiplatform boot with KZM9D DTB
  ARM: shmobile: Remove non-multiplatform KZM9D reference support
  ARM: shmobile: Use KZM9D without reference for multiplatform
  ARM: shmobile: Sync KZM9D DTS with KZM9D reference DTS
  ...

Pull ARM SoC platform changes from Olof Johansson:
 "New and updated SoC support.  Among the things new for this release
  are:

   - More support for the AM33xx platforms from TI
   - Tegra 124 support, and some updates to older tegra families as well
   - imx cleanups and updates across the board
   - A rename of Broadcom's Mobile platforms which were introduced as
     ARCH_BCM, and turned out to be too broad a name.  New name is
     ARCH_BCM_MOBILE.
   - A whole bunch of updates and fixes for integrator, making the
     platform code more modern and switches over to DT-only booting.
   - Support for two new Renesas shmobile chipsets.  Next up for them is
     more work on consolidation instead of introduction of new
     non-multiplatform SoCs, we're all looking forward to that!
   - Misc cleanups for older Samsung platforms, some Allwinner updates,
     etc"

* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (159 commits)
  ARM: bcm281xx: Add ARCH_BCM_MOBILE to bcm config
  ARM: bcm_defconfig: Run "make savedefconfig"
  ARM: bcm281xx: Add ARCH Timers to config
  rename ARCH_BCM to ARCH_BCM_MOBILE (mach-bcm)
  ARM: vexpress: Enable platform-specific options in defconfig
  ARM: vexpress: Make defconfig work again
  ARM: sunxi: remove .init_time hooks
  ARM: imx: enable suspend for imx6sl
  ARM: imx: ensure dsm_request signal is not asserted when setting LPM
  ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
  ARM: imx6q: move low-power code out of clock driver
  ARM: imx: drop extern with function prototypes in common.h
  ARM: imx: reset core along with enable/disable operation
  ARM: imx: do not return from imx_cpu_die() call
  ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
  ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
  ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
  ARM: imx: replace imx6q_restart() with mxc_restart()
  ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
  ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
  ...

Pull ARM SoC cleanups from Olof Johansson:
 "This branch contains code cleanups, moves and removals for 3.13.

  Qualcomm msm targets had a bunch of code removal for legacy non-DT
  platforms.  Nomadik saw more device tree conversions and cleanup of
  old code.  Tegra has some code refactoring, etc.

  One longish patch series from Sebastian Hasselbarth changes the
  init_time hooks and tries to use a generic implementation for most
  platforms, since they were all doing more or less the same things.

  Finally the "shark" platform is removed in this release.  It's been
  abandoned for a while and nobody seems to care enough to keep it
  around.  If someone comes along and wants to resurrect it, the removal
  can easily be reverted and code brought back.

  Beyond this, mostly a bunch of removals of stale content across the
  board, etc"

* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (79 commits)
  ARM: gemini: convert to GENERIC_CLOCKEVENTS
  ARM: EXYNOS: remove CONFIG_MACH_EXYNOS[4, 5]_DT config options
  ARM: OMAP3: control: add API for setting IVA bootmode
  ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
  ARM: OMAP3: McBSP: do not access CM register directly
  ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
  ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
  MAINTAINERS: Add patterns for DTS files for AT91
  ARM: at91: remove init_machine() as default is suitable
  ARM: at91/dt: split sama5d3 peripheral definitions
  ARM: at91/dt: split sam9x5 peripheral definitions
  ARM: Remove temporary sched_clock.h header
  ARM: clps711x: Use linux/sched_clock.h
  MAINTAINERS: Add DTS files to patterns for Samsung platform
  ARM: EXYNOS: remove unnecessary header inclusions from exynos4/5 dt machine file
  ARM: tegra: fix ARCH_TEGRA_114_SOC select sort order
  clk: nomadik: fix missing __init on nomadik_src_init
  ARM: drop explicit selection of HAVE_CLK and CLKDEV_LOOKUP
  ARM: S3C64XX: Kill CONFIG_PLAT_S3C64XX
  ASoC: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
  ...

Pull ARM SoC low-priority fixes from Olof Johansson:
 "A set of fixes for various platforms that weren't considered bad
  enough to include in 3.12 (nor -stable).  Mostly simple typo fixes,
  etc"

* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: OMAP2+: irq, AM33XX add missing register check
  ARM: OMAP2+: wakeupgen: AM43x adaptation
  ARM: OMAP1: Fix a bunch of GPIO related section warnings after initdata got corrected
  ARM: dts: fix PL330 MDMA1 address in DT for Universal C210 board
  ARM: dts: Work around lack of cpufreq regulator lookup for exynos4210-origen and trats boards
  ARM: dts: Fix typo earlyprintk in exynos5440-sd5v1 and ssdk5440 boards
  ARM: dts: Correct typo in use of samsung,pin-drv for exynos5250
  ARM: rockchip: remove obsolete rockchip,config properties
  ARM: rockchip: fix wrong use of non-existent CONFIG_LOCAL_TIMERS
  ARM: mach-omap1: Fix omap1510_fpga_init_irq() implicit declarations.
  ARM: OMAP1: fix incorrect placement of __initdata tag
  ARM: OMAP: remove deprecated IRQF_DISABLED
  ARM: OMAP2+: throw the die id into the entropy pool

Pull ARM64 update from Catalin Marinas:
 "Main features:
   - Ticket-based spinlock implementation and lockless lockref support
   - Big endian support
   - CPU hotplug support, currently for PSCI (Power State Coordination
     Interface) capable firmware
   - Virtual address space extended to 42-bit in the 64K page
     configuration (maximum VA space with 2 levels of page tables)
   - Compat (AArch32) kuser helpers updated to ARMv8 (make use of
     load-acquire/store-release instructions)
   - Code cleanup, defconfig update and minor fixes"

* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64: (43 commits)
  ARM64: /proc/interrupts: display IPIs of online CPUs only
  arm64: locks: Remove CONFIG_GENERIC_LOCKBREAK
  arm64: KVM: vgic: byteswap GICv2 access on world switch if BE
  arm64: KVM: initialize HYP mode following the kernel endianness
  arm64: compat: Clear the IT state independent of the 32-bit ARM or Thumb-2 mode
  arm64: Use 42-bit address space with 64K pages
  arm64: module: ensure instruction is little-endian before manipulation
  arm64: defconfig: Enable CONFIG_PREEMPT by default
  arm64: fix access to preempt_count from assembly code
  arm64: move enabling of GIC before CPUs are set online
  arm64: use generic RW_DATA_SECTION macro in linker script
  arm64: Slightly improve the warning on CPU0 enable-method
  ARM64: simplify cpu_read_bootcpu_ops using OF/DT helper
  ARM64: DT: define ARM64 specific arch_match_cpu_phys_id
  arm64: allow ioremap_cache() to use existing RAM mappings
  arm64: update 32-bit kuser helpers to ARMv8
  arm64: perf: fix event number mask
  arm64: kconfig: allow CPU_BIG_ENDIAN to be selected
  arm64: Fix the endianness of arch_spinlock_t
  arm64: big-endian: write CPU holding pen address as LE
  ...

Pull gfs2 updates from Steven Whitehouse:
 "The main feature of interest this time is quota updates.  There are
  some clean ups and some patches to use the new generic lru list code.

  There is still plenty of scope for some further changes in due course -
  faster lookups of quota structures is very much on the todo list.
  Also, a start has been made towards the more tricky issue of using the
  generic lru code with glocks, but that will have to be completed in a
  subsequent merge window.

  The other, more minor feature, is that there have been a number of
  performance patches which relate to block allocation.  In particular
  they will improve performance when the disk is nearly full"

* tag 'gfs2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-nmw:
  GFS2: Use generic list_lru for quota
  GFS2: Rename quota qd_lru_lock qd_lock
  GFS2: Use reflink for quota data cache
  GFS2: Use lockref for glocks
  GFS2: Protect quota sync generation
  GFS2: Inline qd_trylock into gfs2_quota_unlock
  GFS2: Make two similar quota code fragments into a function
  GFS2: Remove obsolete quota tunable
  GFS2: Move gfs2_icbit_munge into quota.c
  GFS2: Speed up starting point selection for block allocation
  GFS2: Add allocation parameters structure
  GFS2: Clean up reservation removal
  GFS2: fix dentry leaks
  GFS2: new function gfs2_rbm_incr
  GFS2: Introduce rbm field bii
  GFS2: Do not reset flags on active reservations
  GFS2: introduce bi_blocks for optimization
  GFS2: optimize rbm_from_block wrt bi_start
  GFS2: d_splice_alias() can't return error

Merge tag 'ftrace-urgent-3.12-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull perf/ftrace fix from Steven Rostedt:
 "Dave Jones's trinity program was able to enable the function tracer
  from a normal user account via the perf syscall "perf_event_open()".
  When I was able to reproduce it with trinity, I was able to track down
  exactly how it happened.

  I discovered that the check for whether the function tracepoint should
  be activated or not was using the "perf_paranoid_kernel()" check which
  by default, lets the user continue.  The user should not by default be
  able to enable function tracing.

  The fix is to use "perf_paranoid_tracepoint_raw()" which will not let
  the user enable function tracing.  This is a security fix as normal
  users should never be allowed to enable the function tracer"

* tag 'ftrace-urgent-3.12-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  perf/ftrace: Fix paranoid level for enabling function tracer

Pull MIPS updates from Ralf Baechle:
 - Some minor work bringing the Cobalt MIPS platforms in line with other
   MIPS platforms
 - Make vmlinux.32 and vmlinux.64 build messages less verbose
 - Always register the R4k clocksource when selected, the clock source's
   rating will decide if this or another clock source is actually going
   to be used
 - Drop support for the Cisco (formerly Scientific Atlanta) PowerTV
   platform.  There appears to be nobody left who cares and the USB
   driver went stale while waiting for years to be merged
 - Some cleanup of Loongson 2 related #ifdefery
 - Various minor cleanups
 - Major rework on all things related to tracing / ptrace on MIPS,
   including switching the MIPS ELF core dumper to regsets, enabling the
   entries for SIGSYS in struct siginfo for MIPS, enabling ftrace
   syscall trace points
 - Some more work to bring DECstation support code in line with other
   more modern code
 - Report the name of the detected CPU, not just its CP0 PrID value
 - Some more BCM 47xx and atheros ath79xx work
 - Support for compressed kernels using the XZ compression scheme

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (53 commits)
  MIPS: remove duplicate define
  MIPS: Random whitespace clean-ups
  MIPS: traps: Reformat notify_die invocations to 80 columns.
  MIPS: Print correct PC in trace dump after NMI exception
  MIPS: kernel: cpu-probe: Report CPU id during probe
  MIPS: Remove unused defines in piix4.h
  MIPS: Get rid of hard-coded values for Malta PIIX4 fixups
  MIPS: Always register R4K clock when selected
  MIPS: Loongson: Get rid of Loongson 2 #ifdefery all over arch/mips.
  MIPS: cacheops.h: Increase indentation by one tab.
  MIPS: Remove bogus BUG_ON()
  MIPS: PowerTV: Remove support code.
  MIPS: ftrace: Add support for syscall tracepoints.
  MIPS: ptrace: Switch syscall reporting to tracehook_report_syscall_entry().
  MIPS: Move audit_arch() helper function to __syscall_get_arch().
  MIPS: Enable HAVE_ARCH_TRACEHOOK.
  MIPS: Switch ELF core dumper to use regsets.
  MIPS: Implement task_user_regset_view.
  MIPS: ptrace: Use tracehook helpers.
  MIPS: O32 / 32-bit: Always copy 4 stack arguments.
  ...

Pull s390 updates from Martin Schwidefsky:
 "The bulk of the patches for the 3.13 merge window.

  Heiko spent quite a bit of work to improve the code generation for the
  kernel.  That includes the exploitation of the interlocked-access
  facility for the atomics and bitops implementation and the improvement
  for the -march and -mtune compiler settings.

  Another important change is the removal of the user_mode=home option,
  user processes now always run in primary space.  The storage keys are
  not initialized at system startup any more, with that the storage key
  removal work is complete.  For the PCI support the hibernation hooks
  have been implemented.

  And as usual cleanup and fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (62 commits)
  s390/scm_blk: fix endless loop for requests != REQ_TYPE_FS
  s390/mm,tlb: correct tlb flush on page table upgrade
  s390/mm: page_table_realloc returns failure
  s390: allow to set gcc -mtune flag
  s390/percpu: remove this_cpu_xor() implementation
  s390/vtime: correct idle time calculation
  s390/time: fix get_tod_clock_ext inline assembly
  tty/hvc_iucv: remove redundant NULL check
  s390/dasd: Write to profile data area only if it is available
  s390: convert use of typedef ctl_table to struct ctl_table
  s390/pci: cleanup function information block
  s390/pci: remove CONFIG_PCI_DEBUG dependancy
  s390/pci: message cleanup
  Update default configuration
  s390: add a couple of useful defconfigs
  s390/percpu: make use of interlocked-access facility 1 instructions
  s390/percpu: use generic percpu ops for CONFIG_32BIT
  s390/compat: make psw32_user_bits a constant value again
  s390: fix handling of runtime instrumentation psw bit
  s390: fix save and restore of the floating-point-control register
  ...

New defconfigs which should be able to boot on any 32/64bit machine.
Many drivers are selected to be compiled-in to avoid the need for an
additional initrd and still being able to boot.
Signed-off-by: Helge Deller <deller@gmx.de>

STI text console (sticon) was broken on 64bit machines with more than
4GB RAM and this lead in some cases to a kernel crash.

Since sticon uses the 32bit STI API it needs to keep pointers to memory
below 4GB. But on a 64bit kernel some memory regions (e.g. the kernel
stack) might be above 4GB which then may crash the kernel in the STI
functions.

Additionally sticon didn't selected the built-in framebuffer fonts by
default. This is now fixed.

On a side-note: Theoretically we could enhance the sticon driver to
use the 64bit STI API. But - beside the fact that some machines don't
provide a 64bit STI ROM - this would just add complexity.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 3.8+

Clean up code to send correct signal on invalid memory accesses:
Send SIGBUS instead of SIGSEGV for memory accesses outside of mmap'ed
areas

This fixes the mmap13 testcase from the Linux Test Project.
Signed-off-by: Helge Deller <deller@gmx.de>

Up to now PA-RISC could live with a trivial version of access_ok().
Our fault handlers can correctly handle fault cases.

But testcases showed that we need a better access check else we won't
always return correct errno failure codes to userspace.

Problem showed up during 32bit userspace tests in which writev() used a
32bit memory area and length which would then wrap around on 64bit
kernel.
Signed-off-by: Helge Deller <deller@gmx.de>

In case we fail to power up other CPUs in a SMP system, the kernel
currently shows a wrong number of online CPUs. This change makes the
output more verbose on how many of the CPUs are online. Example:

CPU(s): 1 out of 2 PA8800 (Mako) at 900.000000 MHz online.
Signed-off-by: Helge Deller <deller@gmx.de>

The number of IPI calls is already visible as per-cpu IPI irq counters
in/proc/cpuinfo, so let's drop this additional counting.

This partly reverts:
cd85d551 parisc: more irq statistics in /proc/interrupts
Signed-off-by: Helge Deller <deller@gmx.de>

Each CPU has it's own Control Register 16 (CR16) which is used as time source
for the udelay() function. But since the CR16 registers across different CPUs
are not synced, we need to recalculate the loop count if we get switched away
to ensure that we really delay as much time as requested.
Signed-off-by: Helge Deller <deller@gmx.de>

This patch removes a duplicate define from
arch/parisc/math-emu/float.h
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Helge Deller <deller@gmx.de>

Install targets (install, zinstall, uinstall) on parisc have a
dependency to vmlinux. This may cause parts of the kernel to be rebuilt
during installation. We must avoid this since this may run as root.
Install targets "ABSOLUTELY MUST NOT MODIFY THE SOURCE TREE." as Linus
emphasized this in:

http://lkml.org/lkml/2013/7/10/600

So on parisc and maybe other archs we need the same as for x86:

1648e4f8 x86, kbuild: make "make install" not depend on vmlinux

This parisc patch was inspired by:

19514fc6 arm, kbuild: make "make install" not depend on vmlinux
Signed-off-by: Helge Deller <deller@gmx.de>

Implement missing functions for parisc to provide kernel audit feature.
Signed-off-by: Helge Deller <deller@gmx.de>

Provide a macro ASM_EXCEPTIONTABLE_ENTRY() to create exception table
entries and convert all open-coded places to use that macro.

This patch is a first step toward creating a exception table which only
holds 32bit pointers even on a 64bit kernel. That way in my own kernel
I was able to reduce the in-kernel exception table from 44kB to 22kB.
Signed-off-by: Helge Deller <deller@gmx.de>

Pull CIFS updates from Steve French:
 "Includes a couple of fixes, plus changes to make multiplex identifiers
  easier to read and correlate with network traces, and a set of
  enhancements for SMB3 dialect.  Also adds support for per-file
  compression for both cifs and smb2/smb3 ("chattr +c filename).

  Should have at least one other merge request ready by next week with
  some new SMB3 security features and copy offload support"

* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
  Query network adapter info at mount time for debugging
  Fix unused variable warning when CIFS POSIX disabled
  Allow setting per-file compression via CIFS protocol
  Query File System Alignment
  Query device characteristics at mount time from server on SMB2/3 not just on cifs mounts
  cifs: Send a logoff request before removing a smb session
  cifs: Make big endian multiplex ID sequences monotonic on the wire
  cifs: Remove redundant multiplex identifier check from check_smb_hdr()
  Query file system attributes from server on SMB2, not just cifs, mounts
  Allow setting per-file compression via SMB2/3
  Fix corrupt SMB2 ioctl requests

Pull NFS client updates from Trond Myklebust:
 "Highlights include:

   - Changes to the RPC socket code to allow NFSv4 to turn off
     timeout+retry:
      * Detect TCP connection breakage through the "keepalive" mechanism
   - Add client side support for NFSv4.x migration (Chuck Lever)
   - Add support for multiple security flavour arguments to the "sec="
     mount option (Dros Adamson)
   - fs-cache bugfixes from David Howells:
     * Fix an issue whereby caching can be enabled on a file that is
       open for writing
   - More NFSv4 open code stable bugfixes
   - Various Labeled NFS (selinux) bugfixes, including one stable fix
   - Fix buffer overflow checking in the RPCSEC_GSS upcall encoding"

* tag 'nfs-for-3.13-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (68 commits)
  NFSv4.2: Remove redundant checks in nfs_setsecurity+nfs4_label_init_security
  NFSv4: Sanity check the server reply in _nfs4_server_capabilities
  NFSv4.2: encode_readdir - only ask for labels when doing readdirplus
  nfs: set security label when revalidating inode
  NFSv4.2: Fix a mismatch between Linux labeled NFS and the NFSv4.2 spec
  NFS: Fix a missing initialisation when reading the SELinux label
  nfs: fix oops when trying to set SELinux label
  nfs: fix inverted test for delegation in nfs4_reclaim_open_state
  SUNRPC: Cleanup xs_destroy()
  SUNRPC: close a rare race in xs_tcp_setup_socket.
  SUNRPC: remove duplicated include from clnt.c
  nfs: use IS_ROOT not DCACHE_DISCONNECTED
  SUNRPC: Fix buffer overflow checking in gss_encode_v0_msg/gss_encode_v1_msg
  SUNRPC: gss_alloc_msg - choose _either_ a v0 message or a v1 message
  SUNRPC: remove an unnecessary if statement
  nfs: Use PTR_ERR_OR_ZERO in 'nfs/nfs4super.c'
  nfs: Use PTR_ERR_OR_ZERO in 'nfs41_callback_up' function
  nfs: Remove useless 'error' assignment
  sunrpc: comment typo fix
  SUNRPC: Add correct rcu_dereference annotation in rpc_clnt_set_transport
  ...

The non-IPI interrupts are displayed only for the online cpus from
show_interrupts in kernel/irq/proc.c before calling arch_show_interrupts().
As a result, the column headers and the IPI count don't match if any
CPU is offline.

This patch fixes show_ipi_list to display IPIs for online CPUs only.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

This reverts commit cb26a311.

It mysteriously causes NetworkManager to not find the wireless device
for me.  As far as I can tell, Tejun *meant* for this commit to not make
any semantic changes, but there clearly are some.  So revert it, taking
into account some of the calling convention changes that happened in
this area in subsequent commits.

Cc: Tejun Heo <tj@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Commit 9a46ad6d "smp: make smp_call_function_many() use logic
similar to smp_call_function_single()" has unified the way to handle
single and multiple cross-CPU function calls. Now only one interrupt
is needed for architecture specific code to support generic SMP function
call interfaces, so kill the redundant single function call interrupt.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

RTSC is strictly incore and must not be allowed in SMP configs
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>