- 01 Jun, 2015 40 commits
-
-
Petri Gynther authored
sdhci_do_set_ios() doesn't currently program SDHCI_HOST_CONTROL2 register correctly when host->preset_enabled == false. Add code to handle the missing cases MMC_SET_DRIVER_TYPE_B and MMC_SET_DRIVER_TYPE_D. Signed-off-by:
Petri Gynther <pgynther@google.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Yangbo Lu authored
Add eSDHC compatible list for P2041/P3041/P4080/P5020/P5040. Signed-off-by:
Yangbo Lu <yangbo.lu@freescale.com> Acked-by:
Scott Wood <scottwood@freescale.com> Signed-off-by:
-
Fabian Frederick authored
Use kernel.h macro definition. Signed-off-by:
Fabian Frederick <fabf@skynet.be> Signed-off-by:
-
Doug Anderson authored
Since the regulator used for the SDMMC IO voltage is not expected to draw a lot of current, most systems will probably use an inexpensive LDO for it. LDO regulators apparently have the feature that they don't actively drive the voltage down--they wait for other components in the system to drag the voltage down. Thus they will transition faster under heavy loads and slower under light loads. During an SDMMC voltage change from 3.3V to 1.8V, we are almost certainly under a light load. To be specific: * The regulator is hooked through pulls to CMD0-3 and DAT. Probably the CMD pulls are something like 47K and the DAT is something like 10K. * The card is supposed to be driving DAT0-3 low during voltage change which will draw _some_ current, but not a lot. * The regulator is also provided to the SDMMC host controller, but the SDMMC host controller is in open drain mode during the voltage change and so shouldn't be drawing much current. In order to keep the SDMMC host working properly (or for noise reasons), there might also be a capacitor attached to the SDMMC IO regulator. This also will have the effect of slowing down transitions of the regulator, especially under light loads. From experimental evidence, we've seen the voltage change fail if the card doesn't detect that the voltage fell to less than about 2.3V when we turn on the clock. On one device (that admittedly had a 47K CMD pullup instead of a 10K CMD pullup) we saw that the voltage was just about 2.3V after 5ms and thus the voltage change would sometimes fail. Doubling the delay gave margin and made the voltage change work 100% of the time, despite the slightly weaker CMD pull. At the moment submitting this as an RFC patch since my problem _could_ be fixed by increasing the pull strength (or using a smaller capacitor). However being a little bit more lenient to strange hardware could also be a good thing. Signed-off-by:
Doug Anderson <dianders@chromium.org> Acked-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Zhangfei Gao authored
Make the modalias match driver name, this is required to make module auto-loading work. Signed-off-by:
Zhangfei Gao <zhangfei.gao@linaro.org> CC: Peter Griffin <peter.griffin@linaro.org> Signed-off-by:
-
Zhangfei Gao authored
Make the modalias match driver name, this is required to make module auto-loading work. Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
-
Zhangfei Gao authored
Make the modalias match driver name, this is required to make module auto-loading work. Signed-off-by:
-
Zhangfei Gao authored
Make the modalias match driver name, this is required to make module auto-loading work. Signed-off-by:
-
Lars-Peter Clausen authored
Use the new MMC_CAP2_NO_WRITE_PROTECT to let the core handle the case where no write protect line is present instead of having custom driver code to handle it. dw_mci_of_get_slot_quirks() is slightly refactored to directly modify the mmc_host capabilities instead of returning a quirk mask. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
Zhangfei Gao authored
Support hi6220, tested on hikey board emmc: support hs sd: support hs, sdr12, sdr25 Signed-off-by:
Jorge A. Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org> Signed-off-by:
Dan Yuan <yuandan@hisilicon.com> Signed-off-by:
-
Zhangfei Gao authored
switch_voltage is required on some platform since special register accessing Signed-off-by:
-
Zhangfei Gao authored
Add bindings for hi6220 mmc support Signed-off-by:
-
Kuninori Morimoto authored
card->csd.capacity is defined as "unsigned int", and sector_t is defined as "u64" or "unsigned long" (depends on CONFIG_LBDAF). Thus, sector_t data might have strange data (see below). This patch cast it to typeof(sector_t) Special thanks to coverity <http://www.coverity.com> ex) if sector_t was u64 unsigned int data; sector_t sector; data = 0x800000; sector = (data << 8); // 0xffffffff80000000 sector = (((typeof(sector_t))data) << 8); // 0x80000000 or data = 0x80000000; sector = (data << 8); // 0x0 sector = (((typeof(sector_t))data) << 8); // 0x8000000000 Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by:
-
Kuninori Morimoto authored
card->ext_csd.enhanced_area_offset is defined as "unsigned long long", and, ext_csd[] is defined as u8. unsigned long long data might have strange data if first bit of ext_csd[] was 1. this patch cast it to (unsigned long long) Special thanks to coverity <http://www.coverity.com> ex) u8 data8; u64 data64; data8 = 0x80; data64 = (data8 << 24); // 0xffffffff80000000 data64 = (((unsigned long long)data8) << 24); // 0x80000000; Signed-off-by:
-
Fabio Estevam authored
Use BUG_ON() instead of an 'if' condition followed by BUG(). The semantic patch that makes this change is available in scripts/coccinelle/misc/bugon.cocci. More information about semantic patching is available at http://coccinelle.lip6.fr/Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Fabio Estevam authored
Simplify a trivial if-return sequence. Possibly combine with a preceding function call. The semantic patch that makes this change is available in scripts/coccinelle/misc/simple_return.cocci. More information about semantic patching is available at http://coccinelle.lip6.fr/Signed-off-by:
-
Fabio Estevam authored
Simplify a trivial if-return sequence. Possibly combine with a preceding function call. The semantic patch that makes this change is available in scripts/coccinelle/misc/simple_return.cocci. More information about semantic patching is available at http://coccinelle.lip6.fr/Signed-off-by:
-
Fabio Estevam authored
The only user of this driver that has not been converted to fully device tree is the i.MX35 SoC. There is a i.MX35-based board (mach-pcm043.c) that uses platform data to pass wp_gpio and cd_gpio information. Commit 8d86e4fc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()") broke the platform data case by removing mmc_gpio_request_ro() and mmc_gpio_request_cd(), so restore the functionality for the non-dt case. Also, restore the check for ESDHC_CD_CONTROLLER so that we can still support the "fsl,cd-controller" property. Signed-off-by:
-
Fabio Estevam authored
mmc_of_parse() should be placed inside sdhci_esdhc_imx_probe_dt() as it suits only for the dt case. Signed-off-by:
-
Lars-Peter Clausen authored
Allow to specify in the device-tree that no physical write-protect signal is connected to a particular instance of a MMC controller. Setting the property will cause the core will assume that the SD card is always read-write. The name for the new property is 'disable-wp' and was chosen based on the property with the same function from the Synopsys designware mobile storage host controller DT bindings specification. Signed-off-by:
-
Lars-Peter Clausen authored
It is not uncommon to see systems where there is no physical write-protect signal (e.g. when using eMMC or microSD card slots). For some controllers, which have a dedicated write-protection detection logic (like SDHCI controllers), the get_ro() callback can return bogus data in such a case. Instead of handling this on a per controller basis this patch adds a new capability flag to the MMC core that can be set to specify that the result of get_ro() is invalid. When the flag is set the core will not call get_ro() and assume that the card is always read-write. Signed-off-by:
-
Adrian Hunter authored
Check the error code for EOPNOTSUPP and do not print reset warning in that case. Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
-
Adrian Hunter authored
Retry errored data requests when re-tuning is needed and add a flag to struct mmc_blk_request so that the retry is only done once. Signed-off-by:
-
Adrian Hunter authored
If re-tuning is needed, do it in the recovery path to give recovery commands a better chance of success. Signed-off-by:
-
Adrian Hunter authored
CRC errors could possibly be alleviated by re-tuning so flag re-tuning needed in those cases. Note this has no effect if re-tuning has not been enabled. Signed-off-by:
-
Adrian Hunter authored
Make use of mmc core support for re-tuning instead of doing it all in the sdhci driver. This patch also changes to flag the need for re-tuning always after runtime suspend when tuning has been used at initialization. Previously it was only done if the re-tuning timer was in use. Signed-off-by:
-
Adrian Hunter authored
HS400 re-tuning must be done in HS200 mode. Add the ability to switch from HS400 mode to HS200 mode before re-tuning and switch back to HS400 after re-tuning. Signed-off-by:
-
Adrian Hunter authored
Make a separate function to do the mmc_switch status check so it can be re-used. This is preparation for adding support for HS400 re-tuning. Signed-off-by:
-
Adrian Hunter authored
The sleep command is issued after deselecting the card, but re-tuning won't work on a deselected card so re-tuning must be held. Signed-off-by:
-
Adrian Hunter authored
Hold re-tuning during bkops to prevent it from conflicting with the busy state. Signed-off-by:
-
Adrian Hunter authored
Hold re-tuning during erase commands to prevent it from conflicting with the sequence of commands. Signed-off-by:
-
Adrian Hunter authored
Hold re-tuning during switch commands to prevent it from conflicting with the busy state or the CMD13 verification. Signed-off-by:
-
Adrian Hunter authored
At the start of each request, re-tune if needed and then hold off re-tuning again until the request is done. Note that though there is one function that starts requests (mmc_start_request) there are two that wait for the request to be done (mmc_wait_for_req_done and mmc_wait_for_data_req_done). Also note that mmc_wait_for_data_req_done can return even when the request is not done (which allows the block driver to prepare a newly arrived request while still waiting for the previous request). This patch ensures re-tuning is held for the duration of a request. Subsequent patches will also hold re-tuning at other times when it might cause a conflict. In addition, possibly a command is failing because re-tuning is needed. Use mmc_retune_recheck() to check re-tuning. At that point re-tuning is held, at least by the request, so mmc_retune_recheck() flags host->retune_now if the hold count is 1. Signed-off-by:
-
Adrian Hunter authored
Enable re-tuning when tuning is executed and disable re-tuning when card is no longer initialized. In the case of SDIO suspend, the card can keep power. In that case, re-tuning need not be disabled, but, if a re-tuning timer is being used, ensure it is disabled and assume that re-tuning will be needed upon resume since it is not known how long the suspend will last. Signed-off-by:
-
Adrian Hunter authored
Currently, there is core support for tuning during initialization. There can also be a need to re-tune periodically (e.g. sdhci) or to re-tune after the host controller is powered off (e.g. after PM runtime suspend / resume) or to re-tune in response to CRC errors. The main requirements for re-tuning are: - ability to enable / disable re-tuning - ability to flag that re-tuning is needed - ability to re-tune before any request - ability to hold off re-tuning if the card is busy - ability to hold off re-tuning if re-tuning is in progress - ability to run a re-tuning timer To support those requirements 7 members are added to struct mmc_host: unsigned int can_retune:1; /* re-tuning can be used */ unsigned int doing_retune:1; /* re-tuning in progress */ unsigned int retune_now:1; /* do re-tuning at next req */ int need_retune; /* re-tuning is needed */ int hold_retune; /* hold off re-tuning */ unsigned int retune_period; /* re-tuning period in secs */ struct timer_list retune_timer; /* for periodic re-tuning */ need_retune is an integer so it can be set without needing synchronization. hold_retune is a integer to allow nesting. Various simple functions are provided to set / clear those variables. Subsequent patches take those functions into use. Signed-off-by:
-
Axel Lin authored
This eliminates having an #ifdef returning NULL for the case when OF is disabled. Signed-off-by:
Axel Lin <axel.lin@ingics.com> Acked-by:
Jisheng Zhang <jszhang@marvell.com> Signed-off-by:
-
Suman Tripathi authored
This patch adds the quirks and compatible string in sdhci-of-arasan.c to support sdhci-arasan4.9a version of controller. Signed-off-by:
Suman Tripathi <stripathi@apm.com> Reviewed-by:
Michal Simek <michal.simek@xilinx.com> Acked-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Krzysztof Kozlowski authored
The platform_device_id is not modified by the driver and core uses it as const. Signed-off-by:
Krzysztof Kozlowski <k.kozlowski.k@gmail.com> Signed-off-by:
-
Krzysztof Kozlowski authored
The platform_device_id is not modified by the driver and core uses it as const. Signed-off-by:
-
Krzysztof Kozlowski authored
The platform_device_id is not modified by the driver and core uses it as const. Signed-off-by:
-
