- 21 Oct, 2017 19 commits
-
-
David S. Miller authored
Igor Russkikh says: ==================== net: aquantia: Atlantic driver 10/2017 updates This patchset fixes various issues in driver, improves parameters for better performance on 10Gbit link ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Igor Russkikh authored
Default Tx rates cause very long ISR delays on Tx. 0xff is 510us delay, giving only ~ 2000 interrupts per seconds for Tx rings cleanup. With these settings udp tx rate was never higher than ~800Mbps on a single stream. Changing min delay to 0xF makes it way better with ~6Gbps TCP stream performance is almost unaffected by this change, since LSO optimizations play important role. CPU load is affected insignificantly by this change. Signed-off-by:
Pavel Belous <pavel.belous@aquantia.com> Signed-off-by:
Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by:
-
Igor Russkikh authored
Aquantia NIC allows both TX and RX interrupt throttle rate (ITR) management, but this was used in a very limited way via predefined values. This patch allows to setup ITR default values via module command line arguments and via standard ethtool coalescing settings. Signed-off-by:
-
Igor Russkikh authored
That may lead to mmio resource leakage. Signed-off-by:
-
Igor Russkikh authored
There is no much practical use from having MSIX vectors more that number of cpus, thus cap this first with preconfigured limit, then with number of cpus online. Signed-off-by:
-
Igor Russkikh authored
When doing ifconfig down/up, driver did not reported carrier_off neither in nic_stop nor in nic_start. That caused link to be visible as "up" during couple of seconds immediately after "ifconfig up". Signed-off-by:
-
Igor Russkikh authored
Queue stat strings are cleaned up, duplicate stat name strings removed, queue restarts counter added Signed-off-by:
-
Igor Russkikh authored
Internal statistics system on chip never gets reset until hardware reboot. This is quite inconvenient in terms of ethtool statistics usage. This patch implements incremental statistics update inside of service callback. Upon nic initialization, first request is done to fetch initial stat data, current collected stat data gets cleared. Internal statistics mailbox readout is improved to save space and increase readability Signed-off-by:
-
Matteo Croce authored
In the UDP code there are two leftover error messages with very few meaning. Replace them with a more descriptive error message as some users reported them as "strange network error". Signed-off-by:
Matteo Croce <mcroce@redhat.com> Signed-off-by:
-
Stefano Brivio authored
On big-endian machines, functions converting between tunnel ID and VNI use the three LSBs of tunnel ID storage to map VNI. The comparison function eq_tun_id_and_vni(), on the other hand, attempted to map the VNI from the three MSBs. Fix it by using the same check implemented on LE, which maps VNI from the three LSBs of tunnel ID. Fixes: 2e0b26e1 ("geneve: Optimize geneve device lookup.") Signed-off-by:
Stefano Brivio <sbrivio@redhat.com> Reviewed-by:
Jakub Sitnicki <jkbs@redhat.com> Signed-off-by:
-
David S. Miller authored
Merge tag 'linux-can-fixes-for-4.14-20171019' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2017-10-19 this is a pull request of 11 patches for the upcoming 4.14 release. There are 6 patches by ZHU Yi for the flexcan driver, that work around the CAN error handling state transition problems found in various incarnations of the flexcan IP core. The patch by Colin Ian King fixes a potential NULL pointer deref in the CAN broad cast manager (bcm). One patch by me replaces a direct deref of a RCU protected pointer by rcu_access_pointer. My second patch adds missing OOM error handling in af_can. A patch by Stefan Mätje for the esd_usb2 driver fixes the dlc in received RTR frames. And the last patch is by Wolfgang Grandegger, it fixes a busy loop in the gs_usb driver in case it runs out of TX contexts. ==================== Signed-off-by:
-
Dexuan Cui authored
Without the patch, when hvs_open_connection() hasn't completely established a connection (e.g. it has changed sk->sk_state to SS_CONNECTED, but hasn't inserted the sock into the connected queue), vsock_stream_connect() may see the sk_state change and return the connection to the userspace, and next when the userspace closes the connection quickly, hvs_release() may not see the connection in the connected queue; finally hvs_open_connection() inserts the connection into the queue, but we won't be able to purge the connection for ever. Signed-off-by:
Dexuan Cui <decui@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Cc: Cathy Avery <cavery@redhat.com> Cc: Rolf Neugebauer <rolf.neugebauer@docker.com> Cc: Marcelo Cerri <marcelo.cerri@canonical.com> Signed-off-by:
-
Gavin Shan authored
The length of GVI (GetVersionInfo) response packet should be 40 instead of 36. This issue was found from /sys/kernel/debug/ncsi/eth0/stats. # ethtool --ncsi eth0 swstats : RESPONSE OK TIMEOUT ERROR ======================================= GVI 0 0 2 With this applied, no error reported on GVI response packets: # ethtool --ncsi eth0 swstats : RESPONSE OK TIMEOUT ERROR ======================================= GVI 2 0 0 Signed-off-by:Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by:
Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by:
-
Gavin Shan authored
The NCSI channel has been configured to provide service if its link monitor timer is enabled, regardless of its state (inactive or active). So the timeout event on the link monitor indicates the out-of-service on that channel, for which a failover is needed. This sets NCSI_DEV_RESHUFFLE flag to enforce failover on link monitor timeout, regardless the channel's original state (inactive or active). Also, the link is put into "down" state to give the failing channel lowest priority when selecting for the active channel. The state of failing channel should be set to active in order for deinitialization and failover to be done. Signed-off-by:
-
Gavin Shan authored
When there are no NCSI channels probed, HWA (Hardware Arbitration) mode is enabled. It's not correct because HWA depends on the fact: NCSI channels exist and all of them support HWA mode. This disables HWA when no channels are probed. Signed-off-by:
-
Samuel Mendoza-Jonas authored
ncsi_channel_monitor() misses stopping the channel monitor in several places that it should, causing a WARN_ON_ONCE() to trigger when the monitor is re-started later, eg: [ 459.040000] WARNING: CPU: 0 PID: 1093 at net/ncsi/ncsi-manage.c:269 ncsi_start_channel_monitor+0x7c/0x90 [ 459.040000] CPU: 0 PID: 1093 Comm: kworker/0:3 Not tainted 4.10.17-gaca2fdd #140 [ 459.040000] Hardware name: ASpeed SoC [ 459.040000] Workqueue: events ncsi_dev_work [ 459.040000] [<80010094>] (unwind_backtrace) from [<8000d950>] (show_stack+0x20/0x24) [ 459.040000] [<8000d950>] (show_stack) from [<801dbf70>] (dump_stack+0x20/0x28) [ 459.040000] [<801dbf70>] (dump_stack) from [<80018d7c>] (__warn+0xe0/0x108) [ 459.040000] [<80018d7c>] (__warn) from [<80018e70>] (warn_slowpath_null+0x30/0x38) [ 459.040000] [<80018e70>] (warn_slowpath_null) from [<803f6a08>] (ncsi_start_channel_monitor+0x7c/0x90) [ 459.040000] [<803f6a08>] (ncsi_start_channel_monitor) from [<803f7664>] (ncsi_configure_channel+0xdc/0x5fc) [ 459.040000] [<803f7664>] (ncsi_configure_channel) from [<803f8160>] (ncsi_dev_work+0xac/0x474) [ 459.040000] [<803f8160>] (ncsi_dev_work) from [<8002d244>] (process_one_work+0x1e0/0x450) [ 459.040000] [<8002d244>] (process_one_work) from [<8002d510>] (worker_thread+0x5c/0x570) [ 459.040000] [<8002d510>] (worker_thread) from [<80033614>] (kthread+0x124/0x164) [ 459.040000] [<80033614>] (kthread) from [<8000a5e8>] (ret_from_fork+0x14/0x2c) This also updates the monitor instead of just returning if ncsi_xmit_cmd() fails to send the get-link-status command so that the monitor properly times out. Fixes: e6f44ed6 "net/ncsi: Package and channel management" Signed-off-by:
-
Samuel Mendoza-Jonas authored
Correct the value of the HNCDSC AEN packet. Fixes: 7a82ecf4 "net/ncsi: NCSI AEN packet handler" Signed-off-by:
-
Eric Dumazet authored
syzkaller got crashes in packet_getsockopt() processing PACKET_ROLLOVER_STATS command while another thread was managing to change po->rollover Using RCU will fix this bug. We might later add proper RCU annotations for sparse sake. In v2: I replaced kfree(rollover) in fanout_add() to kfree_rcu() variant, as spotted by John. Fixes: a9b63918 ("packet: rollover statistics") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Cc: John Sperbeck <jsperbeck@google.com> Signed-off-by:
-
Eric Dumazet authored
syzkaller found another bug in DCCP/TCP stacks [1] For the reasons explained in commit ce105008 ("tcp/dccp: fix ireq->pktopts race"), we need to make sure we do not access ireq->opt unless we own the request sock. Note the opt field is renamed to ireq_opt to ease grep games. [1] BUG: KASAN: use-after-free in ip_queue_xmit+0x1687/0x18e0 net/ipv4/ip_output.c:474 Read of size 1 at addr ffff8801c951039c by task syz-executor5/3295 CPU: 1 PID: 3295 Comm: syz-executor5 Not tainted 4.14.0-rc4+ #80 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:16 [inline] dump_stack+0x194/0x257 lib/dump_stack.c:52 print_address_description+0x73/0x250 mm/kasan/report.c:252 kasan_report_error mm/kasan/report.c:351 [inline] kasan_report+0x25b/0x340 mm/kasan/report.c:409 __asan_report_load1_noabort+0x14/0x20 mm/kasan/report.c:427 ip_queue_xmit+0x1687/0x18e0 net/ipv4/ip_output.c:474 tcp_transmit_skb+0x1ab7/0x3840 net/ipv4/tcp_output.c:1135 tcp_send_ack.part.37+0x3bb/0x650 net/ipv4/tcp_output.c:3587 tcp_send_ack+0x49/0x60 net/ipv4/tcp_output.c:3557 __tcp_ack_snd_check+0x2c6/0x4b0 net/ipv4/tcp_input.c:5072 tcp_ack_snd_check net/ipv4/tcp_input.c:5085 [inline] tcp_rcv_state_process+0x2eff/0x4850 net/ipv4/tcp_input.c:6071 tcp_child_process+0x342/0x990 net/ipv4/tcp_minisocks.c:816 tcp_v4_rcv+0x1827/0x2f80 net/ipv4/tcp_ipv4.c:1682 ip_local_deliver_finish+0x2e2/0xba0 net/ipv4/ip_input.c:216 NF_HOOK include/linux/netfilter.h:249 [inline] ip_local_deliver+0x1ce/0x6e0 net/ipv4/ip_input.c:257 dst_input include/net/dst.h:464 [inline] ip_rcv_finish+0x887/0x19a0 net/ipv4/ip_input.c:397 NF_HOOK include/linux/netfilter.h:249 [inline] ip_rcv+0xc3f/0x1820 net/ipv4/ip_input.c:493 __netif_receive_skb_core+0x1a3e/0x34b0 net/core/dev.c:4476 __netif_receive_skb+0x2c/0x1b0 net/core/dev.c:4514 netif_receive_skb_internal+0x10b/0x670 net/core/dev.c:4587 netif_receive_skb+0xae/0x390 net/core/dev.c:4611 tun_rx_batched.isra.50+0x5ed/0x860 drivers/net/tun.c:1372 tun_get_user+0x249c/0x36d0 drivers/net/tun.c:1766 tun_chr_write_iter+0xbf/0x160 drivers/net/tun.c:1792 call_write_iter include/linux/fs.h:1770 [inline] new_sync_write fs/read_write.c:468 [inline] __vfs_write+0x68a/0x970 fs/read_write.c:481 vfs_write+0x18f/0x510 fs/read_write.c:543 SYSC_write fs/read_write.c:588 [inline] SyS_write+0xef/0x220 fs/read_write.c:580 entry_SYSCALL_64_fastpath+0x1f/0xbe RIP: 0033:0x40c341 RSP: 002b:00007f469523ec10 EFLAGS: 00000293 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 0000000000718000 RCX: 000000000040c341 RDX: 0000000000000037 RSI: 0000000020004000 RDI: 0000000000000015 RBP: 0000000000000086 R08: 0000000000000000 R09: 0000000000000000 R10: 00000000000f4240 R11: 0000000000000293 R12: 00000000004b7fd1 R13: 00000000ffffffff R14: 0000000020000000 R15: 0000000000025000 Allocated by task 3295: save_stack_trace+0x16/0x20 arch/x86/kernel/stacktrace.c:59 save_stack+0x43/0xd0 mm/kasan/kasan.c:447 set_track mm/kasan/kasan.c:459 [inline] kasan_kmalloc+0xad/0xe0 mm/kasan/kasan.c:551 __do_kmalloc mm/slab.c:3725 [inline] __kmalloc+0x162/0x760 mm/slab.c:3734 kmalloc include/linux/slab.h:498 [inline] tcp_v4_save_options include/net/tcp.h:1962 [inline] tcp_v4_init_req+0x2d3/0x3e0 net/ipv4/tcp_ipv4.c:1271 tcp_conn_request+0xf6d/0x3410 net/ipv4/tcp_input.c:6283 tcp_v4_conn_request+0x157/0x210 net/ipv4/tcp_ipv4.c:1313 tcp_rcv_state_process+0x8ea/0x4850 net/ipv4/tcp_input.c:5857 tcp_v4_do_rcv+0x55c/0x7d0 net/ipv4/tcp_ipv4.c:1482 tcp_v4_rcv+0x2d10/0x2f80 net/ipv4/tcp_ipv4.c:1711 ip_local_deliver_finish+0x2e2/0xba0 net/ipv4/ip_input.c:216 NF_HOOK include/linux/netfilter.h:249 [inline] ip_local_deliver+0x1ce/0x6e0 net/ipv4/ip_input.c:257 dst_input include/net/dst.h:464 [inline] ip_rcv_finish+0x887/0x19a0 net/ipv4/ip_input.c:397 NF_HOOK include/linux/netfilter.h:249 [inline] ip_rcv+0xc3f/0x1820 net/ipv4/ip_input.c:493 __netif_receive_skb_core+0x1a3e/0x34b0 net/core/dev.c:4476 __netif_receive_skb+0x2c/0x1b0 net/core/dev.c:4514 netif_receive_skb_internal+0x10b/0x670 net/core/dev.c:4587 netif_receive_skb+0xae/0x390 net/core/dev.c:4611 tun_rx_batched.isra.50+0x5ed/0x860 drivers/net/tun.c:1372 tun_get_user+0x249c/0x36d0 drivers/net/tun.c:1766 tun_chr_write_iter+0xbf/0x160 drivers/net/tun.c:1792 call_write_iter include/linux/fs.h:1770 [inline] new_sync_write fs/read_write.c:468 [inline] __vfs_write+0x68a/0x970 fs/read_write.c:481 vfs_write+0x18f/0x510 fs/read_write.c:543 SYSC_write fs/read_write.c:588 [inline] SyS_write+0xef/0x220 fs/read_write.c:580 entry_SYSCALL_64_fastpath+0x1f/0xbe Freed by task 3306: save_stack_trace+0x16/0x20 arch/x86/kernel/stacktrace.c:59 save_stack+0x43/0xd0 mm/kasan/kasan.c:447 set_track mm/kasan/kasan.c:459 [inline] kasan_slab_free+0x71/0xc0 mm/kasan/kasan.c:524 __cache_free mm/slab.c:3503 [inline] kfree+0xca/0x250 mm/slab.c:3820 inet_sock_destruct+0x59d/0x950 net/ipv4/af_inet.c:157 __sk_destruct+0xfd/0x910 net/core/sock.c:1560 sk_destruct+0x47/0x80 net/core/sock.c:1595 __sk_free+0x57/0x230 net/core/sock.c:1603 sk_free+0x2a/0x40 net/core/sock.c:1614 sock_put include/net/sock.h:1652 [inline] inet_csk_complete_hashdance+0xd5/0xf0 net/ipv4/inet_connection_sock.c:959 tcp_check_req+0xf4d/0x1620 net/ipv4/tcp_minisocks.c:765 tcp_v4_rcv+0x17f6/0x2f80 net/ipv4/tcp_ipv4.c:1675 ip_local_deliver_finish+0x2e2/0xba0 net/ipv4/ip_input.c:216 NF_HOOK include/linux/netfilter.h:249 [inline] ip_local_deliver+0x1ce/0x6e0 net/ipv4/ip_input.c:257 dst_input include/net/dst.h:464 [inline] ip_rcv_finish+0x887/0x19a0 net/ipv4/ip_input.c:397 NF_HOOK include/linux/netfilter.h:249 [inline] ip_rcv+0xc3f/0x1820 net/ipv4/ip_input.c:493 __netif_receive_skb_core+0x1a3e/0x34b0 net/core/dev.c:4476 __netif_receive_skb+0x2c/0x1b0 net/core/dev.c:4514 netif_receive_skb_internal+0x10b/0x670 net/core/dev.c:4587 netif_receive_skb+0xae/0x390 net/core/dev.c:4611 tun_rx_batched.isra.50+0x5ed/0x860 drivers/net/tun.c:1372 tun_get_user+0x249c/0x36d0 drivers/net/tun.c:1766 tun_chr_write_iter+0xbf/0x160 drivers/net/tun.c:1792 call_write_iter include/linux/fs.h:1770 [inline] new_sync_write fs/read_write.c:468 [inline] __vfs_write+0x68a/0x970 fs/read_write.c:481 vfs_write+0x18f/0x510 fs/read_write.c:543 SYSC_write fs/read_write.c:588 [inline] SyS_write+0xef/0x220 fs/read_write.c:580 entry_SYSCALL_64_fastpath+0x1f/0xbe Fixes: e994b2f0 ("tcp: do not lock listener to process SYN packets") Fixes: 079096f1 ("tcp/dccp: install syn_recv requests into ehash table") Signed-off-by:
-
- 20 Oct, 2017 7 commits
-
-
David S. Miller authored
John Fastabend says: ==================== sockmap fixes for net The following implements a set of fixes for sockmap and changes the API slightly in a few places to reduce preempt_disable/enable scope. We do this here in net because it requires an API change and this avoids getting stuck with legacy API going forward. The short description: Access to skb mark is removed, it is problematic when we add features in the future because mark is a union and used by the TCP/socket code internally. We don't want to expose this to the BPF programs or let programs change the values. The other change is caching metadata in the skb itself between when the BPF program returns a redirect code and the core code implements the redirect. This avoids having per cpu metadata. Finally, tighten restriction on using sockmap to CAP_NET_ADMIN and only SOCK_STREAM sockets. ==================== Signed-off-by: -
John Fastabend authored
Devmap is used with XDP which requires CAP_NET_ADMIN so lets also make CAP_NET_ADMIN required to use the map. Signed-off-by:
John Fastabend <john.fastabend@gmail.com> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
John Fastabend authored
Restrict sockmap to CAP_NET_ADMIN. Signed-off-by:
-
John Fastabend authored
The skb->mark field is a union with reserved_tailroom which is used in the TCP code paths from stream memory allocation. Allowing SK_SKB programs to set this field creates a conflict with future code optimizations, such as "gifting" the skb to the egress path instead of creating a new skb and doing a memcpy. Because we do not have a released version of SK_SKB yet lets just remove it for now. A more appropriate scratch pad to use at the socket layer is dev_scratch, but lets add that in future kernels when needed. Signed-off-by:
-
John Fastabend authored
SK_SKB BPF programs are run from the socket/tcp context but early in the stack before much of the TCP metadata is needed in tcp_skb_cb. So we can use some unused fields to place BPF metadata needed for SK_SKB programs when implementing the redirect function. This allows us to drop the preempt disable logic. It does however require an API change so sk_redirect_map() has been updated to additionally provide ctx_ptr to skb. Note, we do however continue to disable/enable preemption around actual BPF program running to account for map updates. Signed-off-by:
-
John Fastabend authored
Only TCP sockets have been tested and at the moment the state change callback only handles TCP sockets. This adds a check to ensure that sockets actually being added are TCP sockets. For net-next we can consider UDP support. Signed-off-by:
-
Xin Long authored
Now sctp processes icmp redirect packet in sctp_icmp_redirect where it calls sctp_transport_dst_check in which tp->dst can be released. The problem is before calling sctp_transport_dst_check, it doesn't check sock_owned_by_user, which means tp->dst could be freed while a process is accessing it with owning the socket. An use-after-free issue could be triggered by this. This patch is to fix it by checking sock_owned_by_user before calling sctp_transport_dst_check in sctp_icmp_redirect, so that it would not release tp->dst if users still hold sock lock. Besides, the same issue fixed in commit 45caeaa5 ("dccp/tcp: fix routing redirect race") on sctp also needs this check. Fixes: 55be7a9c ("ipv4: Add redirect support to all protocol icmp error handlers") Reported-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
- 19 Oct, 2017 14 commits
-
-
Xin Long authored
Now when peeling off an association to the sock in another netns, all transports in this assoc are not to be rehashed and keep use the old key in hashtable. As a transport uses sk->net as the hash key to insert into hashtable, it would miss removing these transports from hashtable due to the new netns when closing the sock and all transports are being freeed, then later an use-after-free issue could be caused when looking up an asoc and dereferencing those transports. This is a very old issue since very beginning, ChunYu found it with syzkaller fuzz testing with this series: socket$inet6_sctp() bind$inet6() sendto$inet6() unshare(0x40000000) getsockopt$inet_sctp6_SCTP_GET_ASSOC_ID_LIST() getsockopt$inet_sctp6_SCTP_SOCKOPT_PEELOFF() This patch is to block this call when peeling one assoc off from one netns to another one, so that the netns of all transport would not go out-sync with the key in hashtable. Note that this patch didn't fix it by rehashing transports, as it's difficult to handle the situation when the tuple is already in use in the new netns. Besides, no one would like to peel off one assoc to another netns, considering ipaddrs, ifaces, etc. are usually different. Reported-by:
ChunYu Wang <chunwang@redhat.com> Signed-off-by:
-
David S. Miller authored
Daniel Borkmann says: ==================== bpf: Fix for BPF devmap percpu allocation splat The set fixes a splat in devmap percpu allocation when we alloc the flush bitmap. Patch 1 is a prerequisite for the fix in patch 2, patch 1 is rather small, so if this could be routed via -net, for example, with Tejun's Ack that would be good. Patch 3 gets rid of remaining PCPU_MIN_UNIT_SIZE checks, which are percpu allocator internals and should not be used. ==================== Signed-off-by: -
Daniel Borkmann authored
PCPU_MIN_UNIT_SIZE is an implementation detail of the percpu allocator. Given we support __GFP_NOWARN now, lets just let the allocation request fail naturally instead. The two call sites from BPF mistakenly assumed __GFP_NOWARN would work, so no changes needed to their actual __alloc_percpu_gfp() calls which use the flag already. Signed-off-by:
-
Daniel Borkmann authored
It was reported that syzkaller was able to trigger a splat on devmap percpu allocation due to illegal/unsupported allocation request size passed to __alloc_percpu(): [ 70.094249] illegal size (32776) or align (8) for percpu allocation [ 70.094256] ------------[ cut here ]------------ [ 70.094259] WARNING: CPU: 3 PID: 3451 at mm/percpu.c:1365 pcpu_alloc+0x96/0x630 [...] [ 70.094325] Call Trace: [ 70.094328] __alloc_percpu_gfp+0x12/0x20 [ 70.094330] dev_map_alloc+0x134/0x1e0 [ 70.094331] SyS_bpf+0x9bc/0x1610 [ 70.094333] ? selinux_task_setrlimit+0x5a/0x60 [ 70.094334] ? security_task_setrlimit+0x43/0x60 [ 70.094336] entry_SYSCALL_64_fastpath+0x1a/0xa5 This was due to too large max_entries for the map such that we surpassed the upper limit of PCPU_MIN_UNIT_SIZE. It's fine to fail naturally here, so switch to __alloc_percpu_gfp() and pass __GFP_NOWARN instead. Fixes: 11393cc9 ("xdp: Add batching support to redirect map") Reported-by:
Mark Rutland <mark.rutland@arm.com> Reported-by:
Shankara Pailoor <sp3485@columbia.edu> Reported-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
-
Daniel Borkmann authored
Add an option for pcpu_alloc() to support __GFP_NOWARN flag. Currently, we always throw a warning when size or alignment is unsupported (and also dump stack on failed allocation requests). The warning itself is harmless since we return NULL anyway for any failed request, which callers are required to handle anyway. However, it becomes harmful when panic_on_warn is set. The rationale for the WARN() in pcpu_alloc() is that it can be tracked when larger than supported allocation requests are made such that allocations limits can be tweaked if warranted. This makes sense for in-kernel users, however, there are users of pcpu allocator where allocation size is derived from user space requests, e.g. when creating BPF maps. In these cases, the requests should fail gracefully without throwing a splat. The current work-around was to check allocation size against the upper limit of PCPU_MIN_UNIT_SIZE from call-sites for bailing out prior to a call to pcpu_alloc() in order to avoid throwing the WARN(). This is bad in multiple ways since PCPU_MIN_UNIT_SIZE is an implementation detail, and having the checks on call-sites only complicates the code for no good reason. Thus, lets fix it generically by supporting the __GFP_NOWARN flag that users can then use with calling the __alloc_percpu_gfp() helper instead. Signed-off-by:
-
David S. Miller authored
Netanel Belgazal says: ==================== ENA ethernet driver bug fixes Some fixes for ENA ethernet driver ==================== Signed-off-by: -
Netanel Belgazal authored
ethtool ena_get_channels() expose the max number of queues as the max number of queues ENA supports (128 queues) and not the actual number of created queues. Signed-off-by:
Netanel Belgazal <netanel@amazon.com> Signed-off-by:
-
Netanel Belgazal authored
This failure is rare and only found on testing where deliberately fail devm_ioremap() [ 451.170464] ena 0000:04:00.0: failed to remap regs bar 451.170549] Workqueue: pciehp-1 pciehp_power_thread [ 451.170551] task: ffff88085a5f2d00 task.stack: ffffc9000756c000 [ 451.170552] RIP: 0010:devm_iounmap+0x2d/0x40 [ 451.170553] RSP: 0018:ffffc9000756fac0 EFLAGS: 00010282 [ 451.170554] RAX: 00000000fffffffe RBX: 0000000000000000 RCX: 0000000000000000 [ 451.170555] RDX: ffffffff813a7e00 RSI: 0000000000000282 RDI: 0000000000000282 [ 451.170556] RBP: ffffc9000756fac8 R08: 00000000fffffffe R09: 00000000000009b7 [ 451.170557] R10: 0000000000000005 R11: 00000000000009b6 R12: ffff880856c9d0a0 [ 451.170558] R13: ffffc9000f5c90c0 R14: ffff880856c9d0a0 R15: 0000000000000028 [ 451.170559] FS: 0000000000000000(0000) GS:ffff88085f400000(0000) knlGS:0000000000000000 [ 451.170560] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 451.170561] CR2: 00007f169038b000 CR3: 0000000001c09000 CR4: 00000000003406f0 [ 451.170562] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 451.170562] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 451.170563] Call Trace: [ 451.170572] ena_release_bars.isra.48+0x34/0x60 [ena] [ 451.170574] ena_probe+0x144/0xd90 [ena] [ 451.170579] ? ida_simple_get+0x98/0x100 [ 451.170585] ? kernfs_next_descendant_post+0x40/0x50 [ 451.170591] local_pci_probe+0x45/0xa0 [ 451.170592] pci_device_probe+0x157/0x180 [ 451.170599] driver_probe_device+0x2a8/0x460 [ 451.170600] __device_attach_driver+0x7e/0xe0 [ 451.170602] ? driver_allows_async_probing+0x30/0x30 [ 451.170603] bus_for_each_drv+0x68/0xb0 [ 451.170605] __device_attach+0xdd/0x160 [ 451.170607] device_attach+0x10/0x20 [ 451.170610] pci_bus_add_device+0x4f/0xa0 [ 451.170611] pci_bus_add_devices+0x39/0x70 [ 451.170613] pciehp_configure_device+0x96/0x120 [ 451.170614] pciehp_enable_slot+0x1b3/0x290 [ 451.170616] pciehp_power_thread+0x3b/0xb0 [ 451.170622] process_one_work+0x149/0x360 [ 451.170623] worker_thread+0x4d/0x3c0 [ 451.170626] kthread+0x109/0x140 [ 451.170627] ? rescuer_thread+0x380/0x380 [ 451.170628] ? kthread_park+0x60/0x60 [ 451.170632] ret_from_fork+0x25/0x30 Signed-off-by:
-
Netanel Belgazal authored
Decrease log level of checksum errors as these messages can be triggered remotely by bad packets. Signed-off-by:
-
Wolfgang Grandegger authored
If sending messages with no cable connected, it quickly happens that there is no more TX context available. Then "gs_can_start_xmit()" returns with "NETDEV_TX_BUSY" and the upper layer does retry immediately keeping the CPU busy. To fix that issue, I moved "atomic_dec(&dev->active_tx_urbs)" from "gs_usb_xmit_callback()" to the TX done handling in "gs_usb_receive_bulk_callback()". Renaming "active_tx_urbs" to "active_tx_contexts" and moving it into "gs_[alloc|free]_tx_context()" would also make sense. Signed-off-by:
Wolfgang Grandegger <wg@grandegger.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Stefan Mätje authored
The dlc member of the struct rx_msg contains also the ESD_RTR flag to mark received RTR frames. Without the fix the can_dlc value for received RTR frames would always be set to 8 by get_can_dlc() instead of the received value. Fixes: 96d8e903 ("can: Add driver for esd CAN-USB/2 device") Signed-off-by:
Stefan Mätje <stefan.maetje@esd.eu> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by:
-
Marc Kleine-Budde authored
This patch adds the missing check and error handling for out-of-memory situations, when kzalloc cannot allocate memory. Fixes: cb5635a3 ("can: complete initial namespace support") Acked-by:
Oliver Hartkopp <socketcan@hartkopp.net> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by:
-
Marc Kleine-Budde authored
"proto_tab" is a RCU protected array, when directly accessing the array, sparse throws these warnings: CHECK /srv/work/frogger/socketcan/linux/net/can/af_can.c net/can/af_can.c:115:14: error: incompatible types in comparison expression (different address spaces) net/can/af_can.c:795:17: error: incompatible types in comparison expression (different address spaces) net/can/af_can.c:816:9: error: incompatible types in comparison expression (different address spaces) This patch fixes the problem by using rcu_access_pointer() and annotating "proto_tab" array as __rcu. Signed-off-by: -
Colin Ian King authored
The assignment of net via call sock_net will dereference sk. This is performed before a sanity null check on sk, so there could be a potential null dereference on the sock_net call if sk is null. Fix this by assigning net after the sk null check. Also replace the sk == NULL with the more usual !sk idiom. Detected by CoverityScan CID#1431862 ("Dereference before null check") Fixes: 384317ef ("can: network namespace support for CAN_BCM protocol") Signed-off-by:Colin Ian King <colin.king@canonical.com> Acked-by:
-
