> send me a patch for e1000 and for ixgb and I'll happily apply those :)

boolean_t to bool
TRUE to true
FALSE to false
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

In order to remove the irq_sem code we need to implement strict
adapter state checking to prevent accidental double up or downs
or resets. This code is largely copied from e1000/e1000e.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

On Thu, 2008-03-06 at 10:07 -0800, Kok, Auke wrote:
> send me a patch for e1000 and for ixgb and I'll happily apply those :)

boolean_t to bool
TRUE to true
FALSE to false
comment typo ahread to ahead
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

rt73usb and rt2500usb used in_atomic to determine
if a configuration step should be rescheduled or not.
Since in_atomic() is not a valid method to determine
if sleeping is allowed we should fix the way this is handled
by adding a new flag to rt2x00.

In addition mark LED class support for the drivers broken
since that also uses the broken in_atomic() method but
so far no solution exists to have LED triggers work only
in scheduled context.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It has been observed on rt2500pci hardware that some
frames received with signal 0x0C do not have the OFDM
flag set.

Signals can have 2 meanings:
 1) The PLCP value
 2) The bitrate * 10

For rt2500pci (1) is for frames received with a OFDM rate,
and (2) is for frames received with a CCK rate.
But 0x0C is a invalid bitrate value but is a valid PLCP
value for 54Mbs (obvious OFDM rate).
This means that it is possible that the hardware does not
set the OFDM bit correctly under all circumstances.
This results in rt2x00 failing to detect the rate and
mac80211 triggering a WARN_ON() and dropping the frame.

To bypass this, print a warning when such a frame is received,
and reset the rate to the lowest supported rate for the current band.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

From version 2.20 of the PS3 system software, the hypervisor allows
the guest OSes to specify separate cipher for group and pairwise.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There's no need to compile the N-PHY support code, when the
N-PHY support is disabled in Kconfig.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch completes the changes regarding the packaging of user
parameters.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

a) a bunch of printks in error-handling assums that ->status is
big-endian.
b) bitfields trouble
c) missing annotations

NB: a bunch of structs is declared packed for no good reason, AFAICS.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The rxdone_entry_desc structure contains 3 fields
which are always 1 or 0. We can safe 8 bytes by
replacing them with a single dev_flags fields which
contain the flags for those settings.

Additionally we can remove the OFDM flag since it
is no longer used since the introduction of the
SIGNAL_PLCP flag.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Default WMM params have to be set according to beacon/probe response
information prior to authentication (or IBSS start/join); beacon queue
is configured only in IBSS. This does not affect the use of 'real' WMM
params as reported by AP.
Signed-off-by: Vladimir Koutny <vlado@ksp.sk>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Postpone calling ieee80211_hw_config if hardware scanning is active.
This is similar to solution for software scanning where channel setting
is delayed until scan complete.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds a clean tear down for all block ack sessions if interface
goes down or if a deauthentication is done.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch also fixes the Rx timer's comments
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a wrong debug print when receiving delba
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When you have an AP on channel 13, it will currently often enough
be listed in scan results even when the regulatory domain restricts
to channels 1-11. This is due to channel overlap. To avoid getting
very strange failures, don't show such APs in the scan results. The
failure mode will now go from "I can see the AP but not associate"
to "I can't see the AP although I know it's there" which is easier
to debug.

This problem was first really noticed by Jes Sorensen.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Jes Sorensen <jes@trained-monkey.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use the new ieee80211_get_channel() function instead of open-coding it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add ieee80211_get_channel() which gets you a channel struct for a
specific wiphy if that channel is present in that wiphy.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1. Host command sending functions moved from iwl4965-base.c to iwl-hcmd.c
in iwlcore module
2. enqueue_hcmd function currently stays in iwl4965-base.c. It is invoked
   through the new 'utils' field in priv's ops.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl4965_get_channel_info was moved to iwlcore module
4965 needs to be stripped off
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch removes 4965 host commands from iwl-3945-commands.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch enables RX TKIP decryption in HW.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch add support for TKIP encryption (TX) in HW.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch makes mac80211 able to send a phase1 key for TKIP
decryption.
This is needed for drivers that don't do the rekeying by themselves
(i.e. iwlwifi). Upon IV16 wrap around, the packet is decrypted in SW,
if decryption is ok, mac80211 calls to update_tkip_key  with a new
phase 1 RX key.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch makes mac80211 able to compute a TKIP key from an skb.
The requested key can be a phase 1 or a phase 2 key.
This is useful for drivers who need to provide tkip key to their
HW to enable HW encryption.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds translation for the RX status of an incoming packet.
The incoming status has to be translated to the old scheme in order to know
if the decryption has been done, MIC failure has occured, TTAK is valid etc...
This translation is mandatory for all RX packets when using 5300 and for
all HT packets using 4965.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch cleans up the set_key flow. Rxon with hw encryption bit set is
not sent upon each call to set_key. Separation is made between global key
(WEP) and dynamic key (TKIP + CCMP and WEP in some cases).
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1. Extracting hw and priv initialization from probe function.
2. Moving some initialization functions to core module.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Performing allocation in a separate function (previously handled in
'probe')
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch defines a package struct for iwlwifi parameters, and uses a
single instance of this struct to group all iwl4965 module parameters
together.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch re-orders the iwl4965_pci_probe function.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

A user needing to access these fields can use offsetof() for
access. The comments still contain the offset to assist with
debugging.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Don't store an (hardware base) u8 value in bss_descriptor, but just an
unsigned int (RSSI is really unsigned). Compilers generate more efficent
code for ints than for bytes.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This removes many unused function parameters as well as some not-implemented
functions, e.g. CMD_802_11_GET_STATS. The silly lbs_set_cmd_ctrl_node()
function is now also gone.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* firmware for the CF card supports power saving
* the driver currenly only accept "iwconfig ethX power on|off", so
  I fixed what the range wext ioctl reports.
* initialize value/flags in lbs_get_power()
* get rid of unused parameter psmode in lbs_ps_confirm_sleep()
* some minor debug output tweaks
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Now uses __lbs_cmd() to get the "log" (it's actually more a snapshot of
various counters, not a sequential log). Besides the "mechanical" convertion
the patch add the following logical changes:

* Removes the priv->logmsg variable, it was only used in one place anyway,
  also don't blindly get the counters when associating. Getting the
  counters then the user asks via WEXT for them is good enought.
* don't set wstats.discard.fragment with log.rxfrag, because the latter is
  a counter for successfully received packets, not for fragmented packets.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The old code incorrectly used lbs_cmd_with_response() and now uses
lbs_cmd_async().

While there I noticed that there is no real useful return values for
asynchronous command functions, so I made the function "void".
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This uses a static lbs_cmd_async_callback function, which is a
noop. Just setting the callback argument to __lbs_cmd_async()
to NULL won't work, because then the cmdnode wouldn't be
released.

This also makes __lbs_cmd_async() a static method, which is
now only used by lbs_cmd() and lbs_cmd_async().
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds debugfs support to iwl core
currently only iwl4965 is supported
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>