1. 03 Aug, 2009 7 commits
    • NeilBrown's avatar
      md: Use revalidate_disk to effect changes in size of device. · 449aad3e
      NeilBrown authored
      As revalidate_disk calls check_disk_size_change, it will cause
      any capacity change of a gendisk to be propagated to the blockdev
      inode.  So use that instead of mucking about with locks and
      i_size_write.
      
      Also add a call to revalidate_disk in do_md_run and a few other places
      where the gendisk capacity is changed.
      Signed-off-by: default avatarNeilBrown <neilb@suse.de>
      449aad3e
    • NeilBrown's avatar
      md: allow raid5_quiesce to work properly when reshape is happening. · 64bd660b
      NeilBrown authored
      The ->quiesce method is not supposed to stop resync/recovery/reshape,
      just normal IO.
      But in raid5 we don't have a way to know which stripes are being
      used for normal IO and which for resync etc, so we need to wait for
      all stripes to be idle to be sure that all writes have completed.
      
      However reshape keeps at least some stripe busy for an extended period
      of time, so a call to raid5_quiesce can block for several seconds
      needlessly.
      So arrange for reshape etc to pause briefly while raid5_quiesce is
      trying to quiesce the array so that the active_stripes count can
      drop to zero.
      Signed-off-by: default avatarNeilBrown <neilb@suse.de>
      64bd660b
    • NeilBrown's avatar
      md/raid5: set reshape_position correctly when reshape starts. · e516402c
      NeilBrown authored
      As the internal reshape_progress counter is the main driver
      for reshape, the fact that reshape_position sometimes starts with the
      wrong value has minimal effect.  It is visible in sysfs and that
      is all.
      Signed-off-by: default avatarNeilBrown <neilb@suse.de>
      e516402c
    • NeilBrown's avatar
      md: Handle growth of v1.x metadata correctly. · 70471daf
      NeilBrown authored
      The v1.x metadata does not have a fixed size and can grow
      when devices are added.
      If it grows enough to require an extra sector of storage,
      we need to update the 'sb_size' to match.
      
      Without this, md can write out an incomplete superblock with a
      bad checksum, which will be rejected when trying to re-assemble
      the array.
      
      Cc: stable@kernel.org
      Signed-off-by: default avatarNeilBrown <neilb@suse.de>
      70471daf
    • NeilBrown's avatar
      md: avoid array overflow with bad v1.x metadata · 3673f305
      NeilBrown authored
      We trust the 'desc_nr' field in v1.x metadata enough to use it
      as an index in an array.  This isn't really safe.
      So range-check the value first.
      Signed-off-by: default avatarNeilBrown <neilb@suse.de>
      3673f305
    • NeilBrown's avatar
      md: when a level change reduces the number of devices, remove the excess. · 3a981b03
      NeilBrown authored
      When an array is changed from RAID6 to RAID5, fewer drives are
      needed.  So any device that is made superfluous by the level
      conversion must be marked as not-active.
      For the RAID6->RAID5 conversion, this will be a drive which only
      has 'Q' blocks on it.
      
      Cc: stable@kernel.org
      Signed-off-by: default avatarNeilBrown <neilb@suse.de>
      3a981b03
    • Andre Noll's avatar
      md: Push down data integrity code to personalities. · ac5e7113
      Andre Noll authored
      This patch replaces md_integrity_check() by two new public functions:
      md_integrity_register() and md_integrity_add_rdev() which are both
      personality-independent.
      
      md_integrity_register() is called from the ->run and ->hot_remove
      methods of all personalities that support data integrity.  The
      function iterates over the component devices of the array and
      determines if all active devices are integrity capable and if their
      profiles match. If this is the case, the common profile is registered
      for the mddev via blk_integrity_register().
      
      The second new function, md_integrity_add_rdev() is called from the
      ->hot_add_disk methods, i.e. whenever a new device is being added
      to a raid array. If the new device does not support data integrity,
      or has a profile different from the one already registered, data
      integrity for the mddev is disabled.
      
      For raid0 and linear, only the call to md_integrity_register() from
      the ->run method is necessary.
      Signed-off-by: default avatarAndre Noll <maan@systemlinux.org>
      Signed-off-by: default avatarNeilBrown <neilb@suse.de>
      ac5e7113
  2. 31 Jul, 2009 1 commit
  3. 28 Jul, 2009 12 commits
  4. 27 Jul, 2009 20 commits