Skip to content

L
linux
Switch branch/tag
  1. 17 Feb, 2011 4 commits
    • Hema HK's avatar
      OMAP2430: hwmod data: Add USBOTG · 44d02acf
      Hema HK authored 
      OMAP2430 hwmod data structures are populated with base address, L3 and L4
interface clocks, IRQs and sysconfig register details.

As per OMAP USBOTG specification, need to configure the USBOTG
to smart idle/standby or no idle/standby during data transfer and
force idle/standby when not in use to support retention and off-mode.
By setting HWMOD_SWSUP_SIDLE and HWMOD_SWSUP_MSTANDBY flags, framework
will take care of configuring to no idle/standby when module is enabled
and force idle/standby when suspended.
Signed-off-by: default avatarHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      44d02acf
    • Anand Gadiyar's avatar
      arm: omap4: 4430sdp: drop ehci support · 1dbea0f5
      Anand Gadiyar authored 
      Most revisions of the OMAP4 Blaze/SDP platform do not have
the EHCI signals routed by default. The pads are routed
for the alternate HSI functionality instead, and explicit
board modifications are needed to route the signals to
the USB PHY on the board.

Also, turning on the PHY connected to the EHCI port causes
a board reboot during bootup due to an unintended short
on the rails - this affects many initial revisions of the
board, and needs a minor board mod to fix (or as a
workaround, one should not attempt to power on the
USB PHY).

Given that these boards need explicit board mods to even
get EHCI working (separate from the accidental short above),
we should not attempt to enable EHCI by default.

So drop the EHCI support from the board files for the
Blaze/SDP platforms.
Signed-off-by: default avatarAnand Gadiyar <gadiyar@ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      1dbea0f5
    • Anand Gadiyar's avatar
      arm: omap4: usb: explicitly configure MUSB pads · 2aae4221
      Anand Gadiyar authored 
      Use the mux framework APIs to explicitly configure
the MUSB pads. The MUSB controller in OMAP4 can use
either the old ULPI interface, or the new internal PHY.
Configure the pads accordingly.
Signed-off-by: default avatarAnand Gadiyar <gadiyar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      2aae4221
    • Hema HK's avatar
      usb: musb: AM35x: moving internal phy functions out of usb_musb.c file · fe5a4901
      Hema HK authored 
      Moved all the board specific internal PHY functions out of usb_musb.c file
as this file is shared between the OMAP2+ and AM35xx platforms.
There exists a file which has the functions specific to internal PHY
used for OMAP4 platform. Moved all phy specific functions to this file
and passing these functions through board data in the board file.
Signed-off-by: default avatarHema HK <hemahk@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      fe5a4901
  3. 16 Feb, 2011 2 commits
  5. 15 Feb, 2011 31 commits
  7. 14 Feb, 2011 3 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7