Fixes: fc831825 ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When receiving an Rx LL2 packet, qed fails to unmap the previous buffer.

Fixes: 0a7fb11c ("qed: Add Light L2 support");
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current Logic would allow the creation of a chain with U32_MAX + 1
elements, when the actual maximum supported by the driver infrastructure
is U32_MAX.

Fixes: a91eb52a ("qed: Revisit chain implementation")
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Doorbell HW block can be configured at a granularity
of 16 x CIDs, so we need to make sure that the actual number
of CIDs configured would be a multiplication of 16.

Today, when RoCE is enabled - given that the number is unaligned,
doorbelling the higher CIDs would fail to reach the firmware and
would eventually timeout.

Fixes: dbb799c3 ("qed: Initialize hardware for new protocols")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: Couple of fixes

Couple or small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The num_rec field is 8 bit, so the maximal count number is 255.
This fixes vlans learning not being enabled for wider ranges than 255.

Fixes: a4feea74 ("mlxsw: reg: Add Switch Port VLAN MAC Learning register definition")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The num_rec field is 8 bit, so the maximal count number is 255. This
fixes vlans not being enabled for wider ranges than 255.

Fixes: b2e345f9 ("mlxsw: reg: Add Switch Port VID and Switch Port VLAN Membership registers definitions")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we notify peers of potential changes,  it's also good to update
IGMP memberships.  For example, during VM migration, updating IGMP
memberships will redirect existing multicast streams to the VM at the
new location.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a memory leak, which happens if the connection request
is not fulfilled between parsing the DCCP options and handling the SYN
(because e.g. the backlog is full), because we forgot to free the
list of ack vectors.
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

aszlig observed failing ssh tunnels (-w) during initialization since
commit cc9da6cc ("ipv6: addrconf: use stable address generator for
ARPHRD_NONE"). We already had reports that the mentioned commit breaks
Juniper VPN connections. I can't clearly say that the Juniper VPN client
has the same problem, but it is worth a try to hint to this patch.

Because of the early generation of link local addresses, the kernel now
can start asking for routers on the local subnet much earlier than usual.
Those router solicitation packets arrive inside the ssh channels and
should be transmitted to the tun fd before the configuration scripts
might have upped the interface and made it ready for transmission.

ssh polls on the interface and receives back a POLL_OUT. It tries to send
the earily router solicitation packet to the tun interface.  Unfortunately
it hasn't been up'ed yet by config scripts, thus failing with -EIO. ssh
doesn't retry again and considers the tun interface broken forever.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=121131
Fixes: cc9da6cc ("ipv6: addrconf: use stable address generator for ARPHRD_NONE")
Cc: Bjørn Mork <bjorn@mork.no>
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Reported-by: Jonas Lippuner <jonas@lippuner.ca>
Cc: Jonas Lippuner <jonas@lippuner.ca>
Reported-by: aszlig <aszlig@redmoonstudios.org>
Cc: aszlig <aszlig@redmoonstudios.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

As Eric Dumazet pointed out this also needs to be fixed in IPv6.
v2: Contains the IPv6 tcp/Ipv6 dccp patches as well.

We have seen a few incidents lately where a dst_enty has been freed
with a dangling TCP socket reference (sk->sk_dst_cache) pointing to that
dst_entry. If the conditions/timings are right a crash then ensues when the
freed dst_entry is referenced later on. A Common crashing back trace is:

 #8 [] page_fault at ffffffff8163e648
    [exception RIP: __tcp_ack_snd_check+74]
.
.
 #9 [] tcp_rcv_established at ffffffff81580b64
#10 [] tcp_v4_do_rcv at ffffffff8158b54a
#11 [] tcp_v4_rcv at ffffffff8158cd02
#12 [] ip_local_deliver_finish at ffffffff815668f4
#13 [] ip_local_deliver at ffffffff81566bd9
#14 [] ip_rcv_finish at ffffffff8156656d
#15 [] ip_rcv at ffffffff81566f06
#16 [] __netif_receive_skb_core at ffffffff8152b3a2
#17 [] __netif_receive_skb at ffffffff8152b608
#18 [] netif_receive_skb at ffffffff8152b690
#19 [] vmxnet3_rq_rx_complete at ffffffffa015eeaf [vmxnet3]
#20 [] vmxnet3_poll_rx_only at ffffffffa015f32a [vmxnet3]
#21 [] net_rx_action at ffffffff8152bac2
#22 [] __do_softirq at ffffffff81084b4f
#23 [] call_softirq at ffffffff8164845c
#24 [] do_softirq at ffffffff81016fc5
#25 [] irq_exit at ffffffff81084ee5
#26 [] do_IRQ at ffffffff81648ff8

Of course it may happen with other NIC drivers as well.

It's found the freed dst_entry here:

 224 static bool tcp_in_quickack_mode(struct sock *sk)↩
 225 {↩
 226 ▹       const struct inet_connection_sock *icsk = inet_csk(sk);↩
 227 ▹       const struct dst_entry *dst = __sk_dst_get(sk);↩
 228 ↩
 229 ▹       return (dst && dst_metric(dst, RTAX_QUICKACK)) ||↩
 230 ▹       ▹       (icsk->icsk_ack.quick && !icsk->icsk_ack.pingpong);↩
 231 }↩

But there are other backtraces attributed to the same freed dst_entry in
netfilter code as well.

All the vmcores showed 2 significant clues:

- Remote hosts behind the default gateway had always been redirected to a
different gateway. A rtable/dst_entry will be added for that host. Making
more dst_entrys with lower reference counts. Making this more probable.

- All vmcores showed a postitive LockDroppedIcmps value, e.g:

LockDroppedIcmps                  267

A closer look at the tcp_v4_err() handler revealed that do_redirect() will run
regardless of whether user space has the socket locked. This can result in a
race condition where the same dst_entry cached in sk->sk_dst_entry can be
decremented twice for the same socket via:

do_redirect()->__sk_dst_check()-> dst_release().

Which leads to the dst_entry being prematurely freed with another socket
pointing to it via sk->sk_dst_cache and a subsequent crash.

To fix this skip do_redirect() if usespace has the socket locked. Instead let
the redirect take place later when user space does not have the socket
locked.

The dccp/IPv6 code is very similar in this respect, so fixing it there too.

As Eric Garver pointed out the following commit now invalidates routes. Which
can set the dst->obsolete flag so that ipv4_dst_check() returns null and
triggers the dst_release().

Fixes: ceb33206 ("ipv4: Kill routes during PMTU/redirect updates.")
Cc: Eric Garver <egarver@redhat.com>
Cc: Hannes Sowa <hsowa@redhat.com>
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. modify bd_status from u32 to u16 in function hdlc_rx_done,
because bd_status register is 16bits
2. write bd_length register before writing bd_status register
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The required changes in the function vxlan_dev_create() were missing
in commit 8bcdc4f3.
The vxlan device is not registered anymore after this patch and the error
path causes an stack dump:
 WARNING: CPU: 3 PID: 1498 at net/core/dev.c:6713 rollback_registered_many+0x9d/0x3f0

Fixes: 8bcdc4f3 ("vxlan: add changelink support")
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The previous idea was to check whether a net namespace is in
net_exit_list or not. It doesn't work, because net->exit_list is used in
__register_pernet_operations and __unregister_pernet_operations where
all namespaces are added to a temporary list to make cleanup in a error
case, so list_empty(&net->exit_list) always returns false.
Reported-by: Mantas Mikulėnas <grawity@gmail.com>
Fixes: 002d8a1a ("net: skip genenerating uevents for network namespaces that are exiting")
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andreas reports kernel oops during rmmod of the br_netfilter module.
Hannes debugged the oops down to a NULL rt6info->rt6i_indev.

Problem is that br_netfilter has the nasty concept of adding a fake
rtable to skb->dst; this happens in a br_netfilter prerouting hook.

A second hook (in bridge LOCAL_IN) is supposed to remove these again
before the skb is handed up the stack.

However, on module unload hooks get unregistered which means an
skb could traverse the prerouting hook that attaches the fake_rtable,
while the 'fake rtable remove' hook gets removed from the hooklist
immediately after.

Fixes: 34666d46 ("netfilter: bridge: move br_netfilter out of the core")
Reported-by: Andreas Karis <akaris@redhat.com>
Debugged-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip6_fragment, in case skb has a fraglist, checks if the
skb is cloned.  If it is, it will move to the 'slow path' and allocates
new skbs for each fragment.

However, right before entering the slowpath loop, it updates the
nexthdr value of the last ipv6 extension header to NEXTHDR_FRAGMENT,
to account for the fragment header that will be inserted in the new
ipv6-fragment skbs.

In case original skb is cloned this munges nexthdr value of another
skb.  Avoid this by doing the nexthdr update for each of the new fragment
skbs separately.

This was observed with tcpdump on a bridge device where netfilter ipv6
reassembly is active:  tcpdump shows malformed fragment headers as
the l4 header (icmpv6, tcp, etc). is decoded as a fragment header.

Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: Andreas Karis <akaris@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.

The endpoints are specifically dereferenced in the i2400m_bootrom_init
path during probe (e.g. in i2400mu_tx_bulk_out).

Fixes: f398e424 ("i2400m/USB: probe/disconnect, dev init/shutdown
and reset backends")
Cc: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.

Fixes: cf7776dc ("[PATCH] isdn4linux: Siemens Gigaset drivers -
direct USB connection")
Cc: stable <stable@vger.kernel.org>	# 2.6.17
Cc: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 27596472 ("ipv6: fix ECMP route replacement") introduced a
loop that removes all siblings of an ECMP route that is being
replaced. However, this loop doesn't stop when it has replaced
siblings, and keeps removing other routes with a higher metric.
We also end up triggering the WARN_ON after the loop, because after
this nsiblings < 0.

Instead, stop the loop when we have taken care of all routes with the
same metric as the route being replaced.

  Reproducer:
  ===========
    #!/bin/sh

    ip netns add ns1
    ip netns add ns2
    ip -net ns1 link set lo up

    for x in 0 1 2 ; do
        ip link add veth$x netns ns2 type veth peer name eth$x netns ns1
        ip -net ns1 link set eth$x up
        ip -net ns2 link set veth$x up
    done

    ip -net ns1 -6 r a 2000::/64 nexthop via fe80::0 dev eth0 \
            nexthop via fe80::1 dev eth1 nexthop via fe80::2 dev eth2
    ip -net ns1 -6 r a 2000::/64 via fe80::42 dev eth0 metric 256
    ip -net ns1 -6 r a 2000::/64 via fe80::43 dev eth0 metric 2048

    echo "before replace, 3 routes"
    ip -net ns1 -6 r | grep -v '^fe80\|^ff00'
    echo

    ip -net ns1 -6 r c 2000::/64 nexthop via fe80::4 dev eth0 \
            nexthop via fe80::5 dev eth1 nexthop via fe80::6 dev eth2

    echo "after replace, only 2 routes, metric 2048 is gone"
    ip -net ns1 -6 r | grep -v '^fe80\|^ff00'

Fixes: 27596472 ("ipv6: fix ECMP route replacement")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Improve bpf_{prog,jit_binary}_{un,}lock_ro() by throwing a
one-time warning in case of an error when the image couldn't
be set read-only, and also mark struct bpf_prog as locked when
bpf_prog_lock_ro() was called.

Reason for the latter is that bpf_prog_unlock_ro() is called from
various places including error paths, and we shouldn't mess with
page attributes when really not needed.

For bpf_jit_binary_unlock_ro() this is not needed as jited flag
implicitly indicates this, thus for archs with ARCH_HAS_SET_MEMORY
we're guaranteed to have a previously locked image. Overall, this
should also help us to identify any further potential issues with
set_memory_*() helpers.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent merge of 'linux-kselftest-4.11-rc1' tree broke bpf test build.
None of the tests were building and test_verifier.c had tons of compiler errors.
Fix it and add #ifdef CAP_IS_SUPPORTED to support old versions of libcap.
Tested on centos 6.8 and 7
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Multipath routes can be rendered usesless when a device in one of the
paths is deleted. For example:

$ ip -f mpls ro ls
100
	nexthop as to 200 via inet 172.16.2.2  dev virt12
	nexthop as to 300 via inet 172.16.3.2  dev br0
101
	nexthop as to 201 via inet6 2000:2::2  dev virt12
	nexthop as to 301 via inet6 2000:3::2  dev br0

$ ip li del br0

When br0 is deleted the other hop is not considered in
mpls_select_multipath because of the alive check -- rt_nhn_alive
is 0.

rt_nhn_alive is decremented once in mpls_ifdown when the device is taken
down (NETDEV_DOWN) and again when it is deleted (NETDEV_UNREGISTER). For
a 2 hop route, deleting one device drops the alive count to 0. Since
devices are taken down before unregistering, the decrement on
NETDEV_UNREGISTER is redundant.

Fixes: c89359a4 ("mpls: support for dead routes")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some cases during XenBus disconnect event handling and subsequent
queue resource release there may be some TX handlers active on
other processors. Use RCU in order to synchronize with them.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the mpls_router module is unloaded, mpls routes are deleted but
notifications are not sent to userspace leaving userspace caches
out of sync. Add the call to mpls_notify_route in mpls_net_exit as
routes are freed.

Fixes: 0189197f ("mpls: Basic routing support")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcf_connmark_init does not check in its configuration if TCA_CONNMARK_PARMS
is set, resulting in a null pointer dereference when trying to access it.

[501099.043007] BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
[501099.043039] IP: [<ffffffffc10c60fb>] tcf_connmark_init+0x8b/0x180 [act_connmark]
...
[501099.044334] Call Trace:
[501099.044345]  [<ffffffffa47270e8>] ? tcf_action_init_1+0x198/0x1b0
[501099.044363]  [<ffffffffa47271b0>] ? tcf_action_init+0xb0/0x120
[501099.044380]  [<ffffffffa47250a4>] ? tcf_exts_validate+0xc4/0x110
[501099.044398]  [<ffffffffc0f5fa97>] ? u32_set_parms+0xa7/0x270 [cls_u32]
[501099.044417]  [<ffffffffc0f60bf0>] ? u32_change+0x680/0x87b [cls_u32]
[501099.044436]  [<ffffffffa4725d1d>] ? tc_ctl_tfilter+0x4dd/0x8a0
[501099.044454]  [<ffffffffa44a23a1>] ? security_capable+0x41/0x60
[501099.044471]  [<ffffffffa470ca01>] ? rtnetlink_rcv_msg+0xe1/0x220
[501099.044490]  [<ffffffffa470c920>] ? rtnl_newlink+0x870/0x870
[501099.044507]  [<ffffffffa472cc61>] ? netlink_rcv_skb+0xa1/0xc0
[501099.044524]  [<ffffffffa47073f4>] ? rtnetlink_rcv+0x24/0x30
[501099.044541]  [<ffffffffa472c634>] ? netlink_unicast+0x184/0x230
[501099.044558]  [<ffffffffa472c9d8>] ? netlink_sendmsg+0x2f8/0x3b0
[501099.044576]  [<ffffffffa46d8880>] ? sock_sendmsg+0x30/0x40
[501099.044592]  [<ffffffffa46d8e03>] ? SYSC_sendto+0xd3/0x150
[501099.044608]  [<ffffffffa425fda1>] ? __do_page_fault+0x2d1/0x510
[501099.044626]  [<ffffffffa47fbd7b>] ? system_call_fast_compare_end+0xc/0x9b

Fixes: 22a5dc0e ("net: sched: Introduce connmark action")
Signed-off-by: Étienne Noss <etienne.noss@wifirst.fr>
Signed-off-by: Victorien Molle <victorien.molle@wifirst.fr>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It wasn't clear if the 'forwarding' setting needs to be enabled on the
interface that packets are received from, or on the interface that
packets are forwarded to, or both.

In fact (according to my code reading) the setting is relevant on the
interface that packets are received from, so this change updates the doc
to say that.
Signed-off-by: Neil Jerram <neil@tigera.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the send indirection table from the inner device (netvsc)
to the network device context.

It is possible that netvsc_device is not present (remove in progress).
This solves potential use after free issues when packet is being
created during MTU change, shutdown, or queue count changes.

Fixes: d8e18ee0 ("netvsc: enhance transmit select_queue")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a network interface controlled by the aquantia ethernet driver is brought
down a warning is output in dmesg (see below).

The problem is that aq_pci_func_free_irqs() is calling free_irq() before it is
calling irq_set_affinity_hint().

WARNING: CPU: 4 PID: 10068 at kernel/irq/manage.c:1503 __free_irq+0x24d/0x2b0
<snip>
Call Trace:
 dump_stack+0x63/0x87
 __warn+0xd1/0xf0
 warn_slowpath_null+0x1d/0x20
 __free_irq+0x24d/0x2b0
 free_irq+0x39/0x90
 aq_pci_func_free_irqs+0x52/0xa0 [atlantic]
 aq_nic_stop+0xca/0xd0 [atlantic]
 aq_ndev_close+0x1d/0x40 [atlantic]
 __dev_close_many+0x99/0x100
 __dev_close+0x67/0xb0
<snip>

Fixes: 36a4a50f ("net: ethernet: aquantia: switch to pci_alloc_irq_vectors")

Cc: Christoph Hellwig <hch@lst.de>
Cc: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David Arcari <darcari@redhat.com>
Tested-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox mlx5 fixes 2017-03-09

This series contains some mlx5 core and ethernet driver fixes.

For -stable:
net/mlx5e: remove IEEE/CEE mode check when setting DCBX mode (for kernel >= 4.10)
net/mlx5e: Avoid wrong identification of rules on deletion (for kernel >= 4.9)
net/mlx5: Don't save PCI state when PCI error is detected (for kernel >= 4.9)
net/mlx5: Fix create autogroup prev initializer (for kernel >=4.9)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Change packet type handler to ETH_P_IP instead of ETH_P_ALL
since we are already expecting an IP packet.

Also, using ETH_P_ALL will cause the loopback test packet type handler
to be called on all outgoing packets, especially our own self loopback
test SKB, which will be validated on xmit as well, and we don't want that.

Tested with:
ethtool -t ethX
validated that the loopback test passes.

Fixes: 0952da79 ('net/mlx5e: Add support for loopback selftest')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When deleting offloaded TC flows, we must correctly identify E-switch
rules. The current check could get us wrong w.r.t to rules set on the
PF. Since it's possible to set NIC rules on the PF, switch to SRIOV
offloads mode and then attempt to delete a NIC rule.

To solve that, we add a flags field to offloaded rules, set it on
creation time and use that over the code where currently needed.

Fixes: 8b32580d ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the function setdcbx fails if the request dcbx mode
is either IEEE or CEE. We remove the IEEE/CEE mode check because
we support both IEEE and CEE interfaces.

Fixes: 3a6a931d ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a PCI error is detected the PCI state could be corrupt, don't save
it in that flow. Save the state after initialization. After restoring the
PCI state during slot reset save it again, restoring the state destroys
the previously saved state info.

Fixes: 05ac2c0b ('net/mlx5: Fix race between PCI error handlers and
health work')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The autogroups list is a list of non overlapping group boundaries
sorted by their start index. If the autogroups list wasn't empty
and an empty group slot was found at the start of the list,
the new group was added to the end of the list instead of the
beginning, as the prev initializer was incorrect.
When this was repeated, it caused multiple groups to have
overlapping boundaries.

Fixed that by correctly initializing the prev pointer to the
start of the list.

Fixes: eccec8da ('net/mlx5: Keep autogroups list ordered')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The RxRPC ACK packet may contain an extension that includes the peer's
current Rx window size for this call.  We adjust the local Tx window size
to match.  However, the transmitter can stall if the receive window is
reduced to 0 by the peer and then reopened.

This is because the normal way that the transmitter is re-energised is by
dropping something out of our Tx queue and thus making space.  When a
single gap is made, the transmitter is woken up.  However, because there's
nothing in the Tx queue at this point, this doesn't happen.

To fix this, perform a wake_up() any time we see the peer's Rx window size
increasing.

The observable symptom is that calls start failing on ETIMEDOUT and the
following:

	kAFS: SERVER DEAD state=-62

appears in dmesg.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hwmon temperature sensor devices is registered using a devm_hwmon
API call.  The marvell_release() would then manually free the device,
not using a devm_hmon API, resulting in the device being removed
twice, leading to a crash in kernfs_find_ns() during the second
removal.

Remove the manual removal, which makes marvell_release() empty, so
remove it as well.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 0b04680f ("phy: marvell: Add support for temperature sensor")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Doug Berger says:

====================
net: bcmgenet: minor bug fixes

v2: Accidentally sent the wrong set after rebasing.

This collection contains a number of fixes for minor issues with the
bcmgenet driver most of which were present in the initial submission
of the driver.

Some bugs were uncovered by inspection prior to the upcoming update for
GENETv5 support:
  net: bcmgenet: correct the RBUF_OVFL_CNT and RBUF_ERR_CNT MIB values
  net: bcmgenet: correct MIB access of UniMAC RUNT counters
  net: bcmgenet: reserved phy revisions must be checked first
  net: bcmgenet: synchronize irq0 status between the isr and task

Others bugs were found in power management testing:
  net: bcmgenet: power down internal phy if open or resume fails
  net: bcmgenet: Power up the internal PHY before probing the MII
  net: bcmgenet: decouple flow control from bcmgenet_tx_reclaim
  net: bcmgenet: add begin/complete ethtool ops

Doug Berger (7):
  net: bcmgenet: correct the RBUF_OVFL_CNT and RBUF_ERR_CNT MIB values
  net: bcmgenet: correct MIB access of UniMAC RUNT counters
  net: bcmgenet: reserved phy revisions must be checked first
  net: bcmgenet: power down internal phy if open or resume fails
  net: bcmgenet: synchronize irq0 status between the isr and task
  net: bcmgenet: Power up the internal PHY before probing the MII
  net: bcmgenet: decouple flow control from bcmgenet_tx_reclaim

Edwin Chan (1):
  net: bcmgenet: add begin/complete ethtool ops
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The bcmgenet_tx_reclaim() function is used to reclaim transmit
resources in different places within the driver.  Most of them
should not affect the state of the transmit flow control.

This commit relocates the logic for waking tx queues based on
freed resources to the napi polling function where it is more
appropriate.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure clock is enabled for ethtool ops.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: Edwin Chan <edwin.chan@broadcom.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using the internal PHY it must be powered up when the MII is probed
or the PHY will not be detected.  Since the PHY is powered up at reset
this has not been a problem.  However, when the kernel is restarted with
kexec the PHY will likely be powered down when the kernel starts so it
will not be detected and the Ethernet link will not be established.

This commit explicitly powers up the internal PHY when the GENET driver
is probed to correct this behavior.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>