smps10 should be enabled only in the case of host mode. So stop
doing always_on, boot_on from smps10_out1. The driver will enable
it in host mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Do not reset GPIO1 at boot-up because GPIO 7 in GPIO1 block is used on
OMAP4460 PandaBoard-ES to select voltage register in TPS62361 which
supplies VDD_MPU.

Without this, OMAP4460 PandaBoard-ES boards fail to boot-up because
MPU voltage switches over to VSET0 voltage value (boot voltage) which
is not sufficient to operate the device at OPP100.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Do not reset GPIO0 at  boot-up because GPIO0 is used
on AM335x EVM-SK to control VTT regulators on DDR3.

Without this EVM-SK boards fail to boot-up because
of DDR3 corruption.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

On OMAP we have co-processor IPs, memory controllers,
GPIOs which control regulators and power switches to
PMIC, and SoC internal Bus IPs, some or most of which
should either not be reset or idled or both at init.
(In some cases there are erratas which prevent an IP
from being reset)
Have a way to pass this information from DT.

Update the am33xx/omap4 and omap5 dtsi files with the
new bindings for modules which either should not be
idled. reset or both. A later patch would cleanup the
same information that exists today as part of the hwmod
data files.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The generic PHY framewrok expects different properties than the
old USB PHY framework. Supply those properties.

Fixes USB OTG port on GAT04 and N900 after the Generic PHY framework was
merged in greg/usb-next. [1]

[1] - https://lkml.org/lkml/2013/9/27/581Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The arm arch timers frequency are now programmed in the CNTFREQ
per-cpu register by the timer code using the secure API [1].
So remove the redundant entry from the dts.

[1] http://marc.info/?l=linux-omap&m=138139106312786&w=2Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add mmc2 dt node to dra7-evm board
and model eMMC vcc as fixed regulator.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add mmc1 dt node to dra7-evm board.
Input for ldo1 regulator is controlled by gpio 5 of pcf8575 chip (0x21)
on i2c1 bus. When dt support for gpio-pcf857x is available, input supply
will be modelled as cascaded regulator.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

This allows the palmas pm_power_off to kick in on power off command
and switch off the board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Commit 840ef8b7 ("ARM: dt: add header to define IRQ flags") added
constants for IRQ edge/level triggered types so use it instead of
a magic number to enhance the DT readability.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add device nodes for the HS USB Host port 1, USB PHY and its
required regulator and also pin mux setup for HS USB1 pins.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Commit ad871c10 ("ARM: dts: OMAP: Add usb_otg and glue data to O
added USB OTG support for most OMAP boards but some OMAP3 boards
such as IGEP boards were not updated. This patch adds an USB OTG
device node to these board.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Enable the hdmi output and the LCD Controller on BeagleBone
Black. Also configure the correct pinmux for output of
video data from the SoC to the HDMI encoder.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add LCDC device node in DT for am33xx
Add LCDC and Panel info in DT for am335x-evm

Changes:
- remove redundant/unnecessary SoC specific setting in the board dts
- resolved conflicts on for_3.13/dts
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

AM437x SoC has a DES3DES module similar to the one on OMAP4.
Add DT node for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

AM437x SoC has AES module similar to the one on OMAP4.
Add DT node for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

AES interrupts were previously not used, but after recent changes
to omap-aes driver, its being used.
Correct the interrupt number to have working PIO mode.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add the generic AM33XX AES module's device tree data and
enable it for the am335x-evm, am335x-evmsk, and am335x-bone
platforms.  Also add Documentation file describing the data
for the AES module.

Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
[joelf@ti.com: Dropped interrupt-parent property, documentation fixups]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add the generic AM33XX SHAM module's device tree data and
enable it for the am335x-evm, am335x-evmsk, and am335x-bone
platforms.  Also add Documentation file describing the data
for the SHAM module.

Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
[joelf@ti.com: Dropped interrupt-parent property, documentation fixups]
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

OMAP4 has an DES3DES  module that uses the omap-des crypto driver.
Add DT entries for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

OMAP4 has an AES module that uses the omap-aes crypto driver.
Add DT entries for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Set bus-width to make SD card operate in 4 bit mode.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Set pinmux_emmc_pins mux mode for cmd line to MODE2 in order
to detect eMMC on BBB and BBW + eMMC cape.
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The IGEP AQUILA EXPANSION board is a development platform
for the IGEP COM AQUILA AM335x boards.

The board adds the following connectivity:

    o USB OTG
    o USB HOST
    o HDMI
    o Ethernet
    o Serial Debug (3.3V)
    o 2x46 pin headers
    o EEPROM
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The IGEP COM AQUILA is industrial processors SODIMM module with
following highlights:

   o AM3352/AM3354/AM3358/AM3359 Texas Instruments processor
   o Cortex-A8 ARM CPU
   o 3.3 volts Inputs / Outputs use industrial
   o 256 MB DDR3 SDRAM / 128 Megabytes FLASH
   o MicroSD card reader on-board
   o Ethernet controller on-board
   o JTAG debug connector available
   o Designed for industrial range purposes
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

3.3V fixed regulator does not belong to TPS node - as a result
the fixed regulator is never probed and MMC is continually deferred
due to lack of regulator.

Move the fixed regulator to be at root of platform.

Cc: Joel Fernandes <joelf@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add information about the USB OTG PHY. Without this
the OTG port on beagle will not work.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Provide RESET GPIO and Power regulator for the USB PHY,
the USB Host port mode and the PHY device for the controller.
Also provide pin multiplexer information for USB host pins.

We also relocate omap3_pmx_core pin definations so that they
are close to omap3_pmx_wkup pin definations.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Set the alias for ethernet0 and ethernet1 so that uBoot
can set the MAC address appropriately.

Currently u-boot cannot find the alias and there for does
not set the MAC address.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add DT nodes for TPS659038 PMIC on DRA7 boards.

It is based on top of:
http://comments.gmane.org/gmane.linux.ports.arm.omap/102459.

Documentation:
- Documentation/devicetree/bindings/mfd/palmas.txt
- Documentation/devicetree/bindings/regulator/palmas-pmic.txt

Boot Tested on DRA7 d1 Board.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
[bcousson@baylibre.com: Fix indentation and changelog]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

"gpmc,sync-clki-ps" is not defined/documented, it should be
"gpmc,sync-clk-ps" instead.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The On Chip Peripherals (OCP) device node is a simplified
representation of the AM33XX SoC interconnect. An OCP dev
node is already defined in the am33xx.dtsi Device Tree
source file included by am33xx based boards so there is
no need to redefine this on each board DT file.

Also, the OCP and IP modules directly connected to it are SoC
internal details that is better to keep outside of board files.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

am33xx boards DTS include the am33xx.dtsi Device Tree
source file that already define a pinmux device node for
the AM33XX SoC Pin Multiplex.

Redefining this for each board makes the Device Tree files
harder to modify and maintain so let's just use what is
already defined in the included .dtsi file.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

This matches the vendor 3.8.x configuration that is shipping
with the boards.

The LED layout is now:
 USR0: heartbeat
 USR1: mmc0 (micro-SD slot)
 USR2: cpu0
 USR3: mmc1 (eMMC)

The cpu0 triggers was put in between the mmc triggers to make
is easier to see where the disk activity is.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The micro-SD slot hooks up all four data pins so lets' use them.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The pinmux is specified in am335x-bone-common.dtsi to be
reused by the eMMC cape.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
[bcousson@baylibre.com: Fix traling spaces and useless comments]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

This enables the use of MMC cards even when no card was inserted at boot.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>