Enable ignore consecutive trigger feature which allows to configure the
driver to skip consecutive triggers from the same type.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Fix several issues related to dump delay:
1. In legacy dump trigger, use stop_delay field instead of trig_dis_ms.
2. ini delay is messured in usec so align both ini and legacy to usec.
3. schedule_delayed_work receives the delay value in jiffies so
translate the dump delay to jiffies.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: ea7cb829 ("iwlwifi: dbg: make trigger functions type agnostic")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

We don't support A-step for some device combinations anymore.  So
change them to use B-step, renaming and reorganizing the config
structures.  Additionally, fix one device that was using the wrong
configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Add debug prints for FTM results info. These prints are used by
tests automation.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

In HE-TB PPDUs (labeled HE-TRIG in radiotap), we were overwriting
the data4.spatial_reuse_1 field with the spatial reuse data that
the firmware gives us for SU/MU PPDUs. Fix that by moving that,
we are already setting the data4.spatial_reuse_{1,2,3,4} fields
in the TB PPDU case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 69f3ca8e ("iwlwifi: mvm: show more HE radiotap data for TB PPDUs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The FTM new API uses API TLV bit 15. The driver mistakenly uses
this bit for beacon filter API, although no TLV was assigned for
the beacon filter API. For now, make beacon filter use bit 16
instead (not set by the fw anyway). Once a TLV is assigned to the
beacon filter API it should be updated.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

- The FW supports up to 4 concurrent scans, so adjust the definitions
  accordingly.
- Only a single periodic scan is supported, so enforce it in the code.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

D3 debug data is disabled by default. Currently it is done by tampering
the dump mask. Add an operation that will allow this to be changed
without recompilation.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

For AX210 devices, the periphry for forcing NMI
has changed.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

In AX210 family, UMAC periphery address space moved from
0xA00000 to 0xD00000.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Many periphery addresses have changed in AX210 devices.
Until sorting out which peripheries should be dumped, skip
that step for now.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

In low power modes, the chip clock source for platform integrated
devices is 32kHz. It is generated internally and supplied by a crystal
oscillator. However using a 32kHz sourced from crystal oscillator
has high power penalty.

There is an option to get an external 32kHz clock from the platform. Past
experience shows that the reliability is platform dependent,
i.e. on some platforms it works good and on other it doesn’t.

Working from external clock will save 0.5 mW in sleep state, from overall
1.8mW that we have today, i.e. almost 30%.

Each OEM can enable or disable the use of the external 32kHz clock by
setting a BIOS configuration. In case the OEM configured to use 32kHz
external clock the driver will pass this indication to the FW.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

When flushing TX queues no new TX should go into the system.
However, in the following scenario we get TX:
1. Queues are stopped and there are packets in overflow queue
2. Station is removed and flush begins
3. Flush empties space, and reclaim path TXes SKB from overflow
   queue.

Note that the fact the queues are stopped during the process
doesn't matter - the packet will be TXed since the TX path
doesn't care if TX queues are stopped or not, just if there is
space in the queue, which there is, since we just freed a
packet.

A fix here is rather complicated, since the flow is very racy.

Change code not to warn if we are TXing from overflow TX.
In case there is TX from both overflow TX and TX path we will
miss a warning we optimally had, but we can live with that.

Make sure we don't return before overflow queue is empty, otherwise
we will think queues are empty, but they will be refilled, resulting
with assert.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 3955525d ("iwlwifi: pcie: buffer packets to avoid overflowing Tx queues")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Start supporting API version 46 where applicable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

This is useful for automated tests.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwl_mvm_te_clear_data() is called for cleanup in case sending
the HOT_SPOT_CMD failed. However, in case sending the command
caused a fw error and restart (e.g. if the command is not supported)
then the te_data pointer may no longer be valid, which leads to
a NULL pointer dereference.

Fix it by checking that the te_data pointer is not NULL before
dereferencing it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Until supporting UHB (ultra high band) channels for
devices AX210, do not fail if number of channels reported
by firmware is greater than NL80211_MAX_SUPP_REG_RULES.
The Driver in that case will use only the non-UHB channels.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Add new API and TLV for the ability to send commands in the beginning
and end of reset flow.

The full flow of recovery is:

1. While loading FW, get address (from the TLV) of target buffer
   to read in case of reset
2. If an error/assert happens read the address data from step 1.
3. Reset the HW and load the FW.
4. Send the data read in step 2.
5. Add station keys
6. Send notification to FW that reset flow is done.

The main use of the recovery flow is for support in PN/SN recovery
when offloaded
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Add new device family AX210.
Make the needed changes for this family.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Trigger field ignore_default was changed to override_trig.
The first byte of the field indicates the driver to override existing
configuration or keep the previous one
The second byte of the field indicated the driver to replace the regions
of the previous trigger or to append new regions to it.

Change the way the active triggers are maintained to support trigger
override in different apply points.
Do this by making a trigger that updates at runtime by the
triggers that are being used in the different apply points.

In case of an assert, the driver does not reconfigure the triggers
and uses the old configuration which leads to undefined behavior.
Solve this by clearing the triggers in assert recovery flow.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

TLV 54 holds umac debug related addresses.
TLV 55 holds lmac debug related addresses.
These TLVs aim to replace the alive notification data in the future.

Parse and keep error table addresses received from the TLVs
for both lmac and umac and use these addresses instead of the pointer
received from alive notification.

The feature supports only unified image.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

We now no longer have any special code in
iwl_mvm_pass_packet_to_mac80211(), so don't
need to pass NO_PSDU packets through it.
Stop doing so and clean up the code there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Add support for FTM initiator, i.e. peer measurements with FTM
if the firmware supports FTM.

Additionally, add two defines we depend on in
include/linux/ieee80211.h.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Add support for FTM responder for hardware/firmware combinations
that advertise support for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Implement monitor dram memory dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

WOWLAN images in unified firmwares should not be used, so don't require
them to support wowlan. This will allow to reduce the firmware's file
size.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Implement monitor sram memory dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Currently there is no way to debug RX/TX paths using prints
without harming tpt. Add prints to debug RX allocation path.
We can still get 1.9 gbps with those on.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Use IWL_DL_FW instead. This will free a bit for more
needed prints in newer devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Allocator swaps the pending requests with 0 when it starts
working. This means that relying on it n RX path to decide if
to move to emergency is not always a good idea, since it may
be zero, but there are still a lot of unallocated RBs in the
system. Change allocator to decrement the pending requests on
real time. It is more expensive since it accesses the atomic
variable more times, but it gives the RX path a better idea
of the system's status.
Reported-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 868a1e86 ("iwlwifi: pcie: avoid empty free RB queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Start supporting API version 45 where applicable.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

There is a block of code that is indented at the wrong level. Fix this
with extra tabbing.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In the case of SAE AP, drivers offload authentication to user-space
software, e.g. hostapd. For FullMAC drivers the procedure is as follows.
If auth_type is SAE and user space indicates external authentication
capability, then driver requests authentication offload to user-space
software using cfg80211_external_auth_request call. From that point,
auth frame exchange is performed transparently for driver: user-space
software sends/receives mgmt frames using mgmt_tx/mgmt_frame_register
cfg80211 callbacks. As soon as authenitcation is completed, user-space
software notifies driver about its status using external_auth cfg80211
callback.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In the case of OWE, STA should be able to pass DH IEs from AP assoc
responses to wpa_s for processing. For this purpose DH IEs are
received from firmware in BSS_JOIN events and passed to wireless
core and then to wpa_s as additional optional rsp_ies parameter
for cfg80211_connect_result.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

During wowlan regression tests, sometimes radio is not waking up for wowlan
packet in coex mode. This is because of power save is enabled by default
in case of coex mode greater than one. Hence, disable power save in coex
mode to avoid radio loss.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

We are redownloading the firmware after S4 restore and observed in
stress test that mac80211 sometimes gives power save request after
resume which causes the firmware in bad state. mac_ops_resumed flag
is added to skip that request until initialisation is done and Keeping
power save state is NONE.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

At SDIO restore ieee80211_restart_hw() is getting called to restart all
MAC operations. This step is not required.
Returning 1 from mac80211_resume() will serve this purpose.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

As we missed to detach HCI, while entering power off or hibernation,
an extra hci interface gets created whenever system is woken up, to
avoid this we added hci_detach() in rsi_disconnect(), rsi_freeze(),
and rsi_shutdown() functions which are invoked for these tests.
This patch fixes the issue
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When a wowlan magic-packet has received to wake up the device, currently
driver is not taking care of what kind of packet has received. This patch
will add debug support for wakeup reason in driver.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/wireless/realtek/rtlwifi/base.c: In function 'rtl_c2h_content_parsing':
drivers/net/wireless/realtek/rtlwifi/base.c:2313:13: warning:
 variable 'cmd_seq' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>