Jakub Kicinski says:

====================
nfp: flower: fixes for flower offload

Two fixes for flower matching and tunnel encap.  Pieter fixes
VLAN matching if the entire VLAN id is masked out and match
is only performed on the PCP field.  Louis adds validation of
tunnel flags for encap, most importantly we should not offload
actions on IPv6 tunnels if it's not supported.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes a bug where ipv6 tunnels would report that it is
getting offloaded to hardware but would actually be rejected
by hardware.

Fixes: b27d6a95 ("nfp: compile flower vxlan tunnel set actions")
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously we only checked if the vlan id field is present when trying
to match a vlan tag. The vlan id and vlan pcp field should be treated
independently.

Fixes: 5571e8c9 ("nfp: extend flower matching capabilities")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When __tipc_dump_start() fails with running out of memory,
we have no reason to continue, especially we should avoid
calling tipc_dump_done().

Fixes: 8f5c5fcf ("tipc: call start and done ops directly in __tipc_nl_compat_dumpit()")
Reported-and-tested-by: syzbot+3f8324abccfbf8c74a9f@syzkaller.appspotmail.com
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: fixes 2018-09-12

please apply the following qeth fixes for -net.

Patch 1 resolves a regression in an error path, while patch 2 enables
the SG support by default that was newly introduced with 4.19.
Patch 3 takes care of a longstanding problem with large-order
allocations, and patch 4 fixes a potential out-of-bounds access.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

For inbound data with an unsupported HW header format, only dump the
actual HW header. We have no idea how much payload follows it, and what
it contains. Worst case, we dump past the end of the Inbound Buffer and
access whatever is located next in memory.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth_query_oat_command() currently allocates the kernel buffer for
the SIOC_QETH_QUERY_OAT ioctl with kzalloc. So on systems with
fragmented memory, large allocations may fail (eg. the qethqoat tool by
default uses 132KB).

Solve this issue by using vzalloc, backing the allocation with
non-contiguous memory.
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Scatter-gather transmit brings a nice performance boost. Considering the
rather large MTU sizes at play, it's also totally the Right Thing To Do.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bailing out on allocation error is nice, but we also need to tell the
ccwgroup core that creating the qeth groupdev failed.

Fixes: d3d1b205 ("s390/qeth: allocate netdevice early")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a rds sock is bound, it is inserted into the bind_hash_table
which is protected by RCU. But when releasing rds sock, after it
is removed from this hash table, it is freed immediately without
respecting RCU grace period. This could cause some use-after-free
as reported by syzbot.

Mark the rds sock with SOCK_RCU_FREE before inserting it into the
bind_hash_table, so that it would be always freed after a RCU grace
period.

The other problem is in rds_find_bound(), the rds sock could be
freed in between rhashtable_lookup_fast() and rds_sock_addref(),
so we need to extend RCU read lock protection in rds_find_bound()
to close this race condition.

Reported-and-tested-by: syzbot+8967084bcac563795dc6@syzkaller.appspotmail.com
Reported-by: syzbot+93a5839deb355537440f@syzkaller.appspotmail.com
Cc: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Cc: rds-devel@oss.oracle.com
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oarcle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After system suspend, sometimes the r8169 doesn't work when ethernet
cable gets pluggued.

This issue happens because rtl_reset_work() doesn't get called from
rtl8169_runtime_resume(), after system suspend.

In rtl_task(), RTL_FLAG_TASK_* only gets cleared if this condition is
met:
if (!netif_running(dev) ||
    !test_bit(RTL_FLAG_TASK_ENABLED, tp->wk.flags))
    ...

If RTL_FLAG_TASK_ENABLED was cleared during system suspend while
RTL_FLAG_TASK_RESET_PENDING was set, the next rtl_schedule_task() won't
schedule task as the flag is still there.

So in addition to clearing RTL_FLAG_TASK_ENABLED, also clears other
flags.

Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When processing icmp unreachable message for erspan tunnel, tunnel id
should be erspan_net_id instead of ipgre_net_id.

Fixes: 84e54fe0 ("gre: introduce native tunnel support for ERSPAN")
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If erspan tunnel hasn't been established, we'd better send icmp port
unreachable message after receive erspan packets.

Fixes: 84e54fe0 ("gre: introduce native tunnel support for ERSPAN")
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert pr_info to net_info_ratelimited to limit the total number of
synflood warnings.

Commit 946cedcc ("tcp: Change possible SYN flooding messages")
rate limits synflood warnings to one per listener.

Workloads that open many listener sockets can still see a high rate of
log messages. Syzkaller is one frequent example.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dma_zalloc_coherent() now crashes if no dev pointer is given.
Add a dev pointer to the ltq_dma_channel structure and fill it in the
driver using it.

This fixes a bug introduced in kernel 4.19.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for you net tree:

1) Remove duplicated include at the end of UDP conntrack, from Yue Haibing.

2) Restore conntrack dependency on xt_cluster, from Martin Willi.

3) Fix splat with GSO skbs from the checksum target, from Florian Westphal.

4) Rework ct timeout support, the template strategy to attach custom timeouts
   is not correct since it will not work in conjunction with conntrack zones
   and we have a possible free after use when removing the rule due to missing
   refcounting. To fix these problems, do not use conntrack template at all
   and set custom timeout on the already valid conntrack object. This
   fix comes with a preparation patch to simplify timeout adjustment by
   initializating the first position of the timeout array for all of the
   existing trackers. Patchset from Florian Westphal.

5) Fix missing dependency on from IPv4 chain NAT type, from Florian.

6) Release chain reference counter from the flush path, from Taehee Yoo.

7) After flushing an iptables ruleset, conntrack hooks are unregistered
   and entries are left stale to be cleaned up by the timeout garbage
   collector. No TCP tracking is done on established flows by this time.
   If ruleset is reloaded, then hooks are registered again and TCP
   tracking is restored, which considers packets to be invalid. Clear
   window tracking to exercise TCP flow pickup from the middle given that
   history is lost for us. Again from Florian.

8) Fix crash from netlink interface with CONFIG_NF_CONNTRACK_TIMEOUT=y
   and CONFIG_NF_CT_NETLINK_TIMEOUT=n.

9) Broken CT target due to returning incorrect type from
   ctnl_timeout_find_get().

10) Solve conntrack clash on NF_REPEAT verdicts too, from Michal Vaner.

11) Missing conversion of hashlimit sysctl interface to new API, from
    Cong Wang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After switching to the new procfs API, it is supposed to
retrieve the private pointer from PDE_DATA(file_inode(s->file)),
s->private is no longer referred.

Fixes: 1cd67182 ("netfilter/x_tables: switch to proc_create_seq_private")
Reported-by: Sami Farin <hvtaifwkbgefbaei@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Tested-by: Sami Farin <hvtaifwkbgefbaei@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

NF_REPEAT places the packet at the beginning of the iptables chain
instead of accepting or rejecting it right away. The packet however will
reach the end of the chain and continue to the end of iptables
eventually, so it needs the same handling as NF_ACCEPT and NF_DROP.

Fixes: 368982cd ("netfilter: nfnetlink_queue: resolve clash for unconfirmed conntracks")
Signed-off-by: Michal 'vorner' Vaner <michal.vaner@avast.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Compiler did not catch incorrect typing in the rcu hook assignment.

 % nfct add timeout test-tcp inet tcp established 100 close 10 close_wait 10
 % iptables -I OUTPUT -t raw -p tcp -j CT --timeout test-tcp
 dmesg - xt_CT: Timeout policy `test-tcp' can only be used by L3 protocol number 25000

The CT target bails out with incorrect layer 3 protocol number.

Fixes: 6c1fd7dc ("netfilter: cttimeout: decouple timeout policy from nfnetlink_cttimeout object")
Reported-by: Harsha Sharma <harshasharmaiitr@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Now that cttimeout support for nft_ct is in place, these should depend
on CONFIG_NF_CONNTRACK_TIMEOUT otherwise we can crash when dumping the
policy if this option is not enabled.

[   71.600121] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
[...]
[   71.600141] CPU: 3 PID: 7612 Comm: nft Not tainted 4.18.0+ #246
[...]
[   71.600188] Call Trace:
[   71.600201]  ? nft_ct_timeout_obj_dump+0xc6/0xf0 [nft_ct]
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Doug Smythies says:
  Sometimes it is desirable to temporarily disable, or clear,
  the iptables rule set on a computer being controlled via a
  secure shell session (SSH). While unwise on an internet facing
  computer, I also do it often on non-internet accessible computers
  while testing. Recently, this has become problematic, with the
  SSH session being dropped upon re-load of the rule set.

The problem is that when all rules are deleted, conntrack hooks get
unregistered.

In case the rules are re-added later, its possible that tcp window
has moved far enough so that all packets are considered invalid (out of
window) until entry expires (which can take forever, default
established timeout is 5 days).

Fix this by clearing maxwin of existing tcp connections on register.

v2: don't touch entries on hook removal.
v3: remove obsolete expiry check.
Reported-by: Doug Smythies <dsmythies@telus.net>
Fixes: 4d3a57f2 ("netfilter: conntrack: do not enable connection tracking unless needed")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Quectel EP06 (and EM06/EG06) supports dynamic configuration of USB
interfaces, without the device changing VID/PID or configuration number.
When the configuration is updated and interfaces are added/removed, the
interface numbers change. This means that the current code for matching
EP06 does not work.

This patch removes the current EP06 interface number match, and replaces
it with a match on class, subclass and protocol. Unfortunately, matching
on those three alone is not enough, as the diag interface exports the
same values as QMI. The other serial interfaces + adb export different
values and do not match.

The diag interface only has two endpoints, while the QMI interface has
three. I have therefore added a check for number of interfaces, and we
ignore the interface if the number of endpoints equals two.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A kernel crash occurrs when defragmented packet is fragmented
in ip_do_fragment().
In defragment routine, skb_orphan() is called and
skb->ip_defrag_offset is set. but skb->sk and
skb->ip_defrag_offset are same union member. so that
frag->sk is not NULL.
Hence crash occurrs in skb->sk check routine in ip_do_fragment() when
defragmented packet is fragmented.

test commands:
   %iptables -t nat -I POSTROUTING -j MASQUERADE
   %hping3 192.168.4.2 -s 1000 -p 2000 -d 60000

splat looks like:
[  261.069429] kernel BUG at net/ipv4/ip_output.c:636!
[  261.075753] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[  261.083854] CPU: 1 PID: 1349 Comm: hping3 Not tainted 4.19.0-rc2+ #3
[  261.100977] RIP: 0010:ip_do_fragment+0x1613/0x2600
[  261.106945] Code: e8 e2 38 e3 fe 4c 8b 44 24 18 48 8b 74 24 08 e9 92 f6 ff ff 80 3c 02 00 0f 85 da 07 00 00 48 8b b5 d0 00 00 00 e9 25 f6 ff ff <0f> 0b 0f 0b 44 8b 54 24 58 4c 8b 4c 24 18 4c 8b 5c 24 60 4c 8b 6c
[  261.127015] RSP: 0018:ffff8801031cf2c0 EFLAGS: 00010202
[  261.134156] RAX: 1ffff1002297537b RBX: ffffed0020639e6e RCX: 0000000000000004
[  261.142156] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff880114ba9bd8
[  261.150157] RBP: ffff880114ba8a40 R08: ffffed0022975395 R09: ffffed0022975395
[  261.158157] R10: 0000000000000001 R11: ffffed0022975394 R12: ffff880114ba9ca4
[  261.166159] R13: 0000000000000010 R14: ffff880114ba9bc0 R15: dffffc0000000000
[  261.174169] FS:  00007fbae2199700(0000) GS:ffff88011b400000(0000) knlGS:0000000000000000
[  261.183012] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  261.189013] CR2: 00005579244fe000 CR3: 0000000119bf4000 CR4: 00000000001006e0
[  261.198158] Call Trace:
[  261.199018]  ? dst_output+0x180/0x180
[  261.205011]  ? save_trace+0x300/0x300
[  261.209018]  ? ip_copy_metadata+0xb00/0xb00
[  261.213034]  ? sched_clock_local+0xd4/0x140
[  261.218158]  ? kill_l4proto+0x120/0x120 [nf_conntrack]
[  261.223014]  ? rt_cpu_seq_stop+0x10/0x10
[  261.227014]  ? find_held_lock+0x39/0x1c0
[  261.233008]  ip_finish_output+0x51d/0xb50
[  261.237006]  ? ip_fragment.constprop.56+0x220/0x220
[  261.243011]  ? nf_ct_l4proto_register_one+0x5b0/0x5b0 [nf_conntrack]
[  261.250152]  ? rcu_is_watching+0x77/0x120
[  261.255010]  ? nf_nat_ipv4_out+0x1e/0x2b0 [nf_nat_ipv4]
[  261.261033]  ? nf_hook_slow+0xb1/0x160
[  261.265007]  ip_output+0x1c7/0x710
[  261.269005]  ? ip_mc_output+0x13f0/0x13f0
[  261.273002]  ? __local_bh_enable_ip+0xe9/0x1b0
[  261.278152]  ? ip_fragment.constprop.56+0x220/0x220
[  261.282996]  ? nf_hook_slow+0xb1/0x160
[  261.287007]  raw_sendmsg+0x21f9/0x4420
[  261.291008]  ? dst_output+0x180/0x180
[  261.297003]  ? sched_clock_cpu+0x126/0x170
[  261.301003]  ? find_held_lock+0x39/0x1c0
[  261.306155]  ? stop_critical_timings+0x420/0x420
[  261.311004]  ? check_flags.part.36+0x450/0x450
[  261.315005]  ? _raw_spin_unlock_irq+0x29/0x40
[  261.320995]  ? _raw_spin_unlock_irq+0x29/0x40
[  261.326142]  ? cyc2ns_read_end+0x10/0x10
[  261.330139]  ? raw_bind+0x280/0x280
[  261.334138]  ? sched_clock_cpu+0x126/0x170
[  261.338995]  ? check_flags.part.36+0x450/0x450
[  261.342991]  ? __lock_acquire+0x4500/0x4500
[  261.348994]  ? inet_sendmsg+0x11c/0x500
[  261.352989]  ? dst_output+0x180/0x180
[  261.357012]  inet_sendmsg+0x11c/0x500
[ ... ]

v2:
 - clear skb->sk at reassembly routine.(Eric Dumarzet)

Fixes: fa0f5273 ("ip: use rb trees for IP frag queue.")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tls_sw_sendmsg() allocates plaintext and encrypted SG entries using
function sk_alloc_sg(). In case the number of SG entries hit
MAX_SKB_FRAGS, sk_alloc_sg() returns -ENOSPC and sets the variable for
current SG index to '0'. This leads to calling of function
tls_push_record() with 'sg_encrypted_num_elem = 0' and later causes
kernel crash. To fix this, set the number of SG elements to the number
of elements in plaintext/encrypted SG arrays in case sk_alloc_sg()
returns -ENOSPC.

Fixes: 3c4d7559 ("tls: kernel TLS support")
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Netanel Belgazal says:

====================
bug fixes for ENA Ethernet driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Added memory barriers where they were missing to support multiple
architectures, and removed redundant ones.

As part of removing the redundant memory barriers and improving
performance, we moved to more relaxed versions of memory barriers,
as well as to the more relaxed version of writel - writel_relaxed,
while maintaining correctness.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add READ_ONCE calls where necessary (for example when iterating
over a memory field that gets updated by the hardware).
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

acquire the rtnl_lock during device destruction to avoid
using partially destroyed device.

ena_remove() shares almost the same logic as ena_destroy_device(),
so use ena_destroy_device() and avoid duplications.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ena_destroy_device() can potentially be called twice.
To avoid this, check that the device is running and
only then proceed destroying it.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When ena_destroy_device() is called from ena_suspend(), the device is
still reachable from the driver. Therefore, the driver can send a command
to the device to free all resources.
However, in all other cases of calling ena_destroy_device(), the device is
potentially in an error state and unreachable from the driver. In these
cases the driver must not send commands to the device.

The current implementation does not request resource freeing from the
device even when possible. We add the graceful parameter to
ena_destroy_device() to enable resource freeing when possible, and
use it in ena_suspend().
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The buffer length field in the ena rx descriptor is 16 bit, and the
current driver passes a full page in each ena rx descriptor.
When PAGE_SIZE equals 64kB or more, the buffer length field becomes
zero.
To solve this issue, limit the ena Rx descriptor to use 16kB even
when allocating 64kB kernel pages. This change would not impact ena
device functionality, as 16kB is still larger than maximum MTU.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Starting with driver version 1.5.0, in case of a surprise device
unplug, there is a race caused by invoking ena_destroy_device()
from two different places. As a result, the readless register might
be accessed after it was destroyed.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the documentation in msg_zerocopy.rst, the SO_ZEROCOPY
flag was introduced because send(2) ignores unknown message flags and
any legacy application which was accidentally passing the equivalent of
MSG_ZEROCOPY earlier should not see any new behaviour.

Before commit f214f915 ("tcp: enable MSG_ZEROCOPY"), a send(2) call
which passed the equivalent of MSG_ZEROCOPY without setting SO_ZEROCOPY
would succeed.  However, after that commit, it fails with -ENOBUFS.  So
it appears that the SO_ZEROCOPY flag fails to fulfill its intended
purpose.  Fix it.

Fixes: f214f915 ("tcp: enable MSG_ZEROCOPY")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When nla_put*() fails after nla_nest_start(), we need
to call nla_nest_cancel() to cancel the message, otherwise
we end up calling nla_nest_end() like a success.

Fixes: 0ed5269f ("net/sched: add tunnel option support to act_tunnel_key")
Cc: Davide Caratti <dcaratti@redhat.com>
Cc: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 822fb18a ("xen-netfront: wait xenbus state change when load
module manually") added a new wait queue to wait on for a state change
when the module is loaded manually. Unfortunately there is no wakeup
anywhere to stop that waiting.

Instead of introducing a new wait queue rename the existing
module_unload_q to module_wq and use it for both purposes (loading and
unloading).

As any state change of the backend might be intended to stop waiting
do the wake_up_all() in any case when netback_changed() is called.

Fixes: 822fb18a ("xen-netfront: wait xenbus state change when load module manually")
Cc: <stable@vger.kernel.org> #4.18
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 3559d81e ("r8169: simplify rtl_hw_start_8169") changed order of
two register writes:
1) Caused RxConfig to be written before TX / RX is enabled,
2) Caused TxConfig to be written before TX / RX is enabled.

At least on XIDs 10000000 ("RTL8169sb/8110sb") and
18000000 ("RTL8169sc/8110sc") such writes are ignored by the chip, leaving
values in these registers intact.

Change 1) was reverted by
commit 05212ba8 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices"),
however change 2) wasn't.

In practice, this caused TxConfig's "InterFrameGap time" and "Max DMA Burst
Size per Tx DMA Burst" bits to be zero dramatically reducing TX performance
(in my tests it dropped from around 500Mbps to around 50Mbps).

This patch fixes the issue by moving TxConfig register write a bit later in
the code so it happens after TX / RX is already enabled.

Fixes: 05212ba8 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices")
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: David S. Miller <davem@davemloft.net>

__tipc_nl_compat_dumpit() uses a netlink_callback on stack,
so the only way to align it with other ->dumpit() call path
is calling tipc_dump_start() and tipc_dump_done() directly
inside it. Otherwise ->dumpit() would always get NULL from
cb->args[].

But tipc_dump_start() uses sock_net(cb->skb->sk) to retrieve
net pointer, the cb->skb here doesn't set skb->sk, the net pointer
is saved in msg->net instead, so introduce a helper function
__tipc_dump_start() to pass in msg->net.

Ying pointed out cb->args[0...3] are already used by other
callbacks on this call path, so we can't use cb->args[0] any
more, use cb->args[4] instead.

Fixes: 9a07efa9 ("tipc: switch to rhashtable iterator")
Reported-and-tested-by: syzbot+e93a2c41f91b8e2c7d9b@syzkaller.appspotmail.com
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2018-09-05

This pull request contains some fixes for mlx5 etherent netdevice and
core driver.

Please pull and let me know if there's any problem.

For -stable v4.9:
('net/mlx5: Fix debugfs cleanup in the device init/remove flow')

For -stable v4.12:
("net/mlx5: E-Switch, Fix memory leak when creating switchdev mode FDB tables")

For -stable v4.13:
("net/mlx5: Fix use-after-free in self-healing flow")

For -stable v4.14:
("net/mlx5: Check for error in mlx5_attach_interface")

For -stable v4.15:
("net/mlx5: Fix not releasing read lock when adding flow rules")

For -stable v4.17:
("net/mlx5: Fix possible deadlock from lockdep when adding fte to fg")

For -stable v4.18:
("net/mlx5: Use u16 for Work Queue buffer fragment size")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
net/iucv: fixes 2018-09-05

please apply three straight-forward fixes for iucv. One that prevents
leaking the skb on malformed inbound packets, one to fix the error
handling on transmit error, and one to get rid of a compile warning.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>