- 30 Jul, 2012 38 commits
-
-
Hans Verkuil authored
Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Changes by Hans de Goede: -rework how gain controls work to better match control framework -make awb + gain + red/blue-balance a single auto-cluster -only add the HFLIP control for TAS5130a sensor cams, as it breaks the video on other cams Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Antonio Ospite authored
Signed-off-by:
Antonio Ospite <ospite@studenti.unina.it> Signed-off-by:
-
Antonio Ospite authored
This driver has no controls, so there is no need to convert it to the control framework. Signed-off-by:
-
Hans de Goede authored
The ov7630's gain is weird, at 32 the gain drops to the same level as at 16, so skip 32-47 (of the 0-63 scale). Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans de Goede authored
With the changes from the previous patches device firmware version 14 + usb microcontroller software version 1 works fine too. Signed-off-by:
-
Hans de Goede authored
The previous value made hardware freq seek not work for me, despite having good reception of almost all Dutch radio stations. Signed-off-by:
-
Hans de Goede authored
Since USB receives STATUS_RSSI updates through the interrupt endpoint, there is no need to poll with USB, so get rid of the polling. Note this also changes the order in which the probing of USB devices is done, to avoid si470x_set_chan getting called before the interrupt endpoint is being monitored. Signed-off-by:
-
Hans de Goede authored
Reading registers from the pcear USB dongles with the si470x causes a loud pop (and an alsa buffer overrun). Since most radio apps periodically call G_TUNER to update mono/stereo, signal and afc status this leads to the music . pop . music . pop . music -> not good. On the internet there is an howto for flashing the pcear with a newer firmware from the silabs reference boardto fix this, but: 1) This howto relies on a special version of the driver which allows firmware flashing 2) We should try to avoid the answer to a bug report being upgrade your firmware, if at all possible 3) Windows does not suffer from the pop sounds After a quick look at the driver I found at that the register reads are not necessary at all, as the device gives us the necessary status through usb interrupt packets, and the driver already uses these! Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans de Goede authored
Some devices which use the tea575x tuner chip don't allow direct control over the IO pins, and thus cannot mute the audio output. Signed-off-by:
-
Hans de Goede authored
Some devices which use the tea575x tuner chip don't allow bit banging the lines, instead they offer a method to directly set / get the contents of the 25 bit shift-register in the chip. Notably the Griffin radioSHARK USB radio receiver does this. Signed-off-by:
-
Hans Verkuil authored
Fixes an omission in the new v4l2_ioctls table: VIDIOC_TRY_EXT_CTRLS must get the INFO_FL_CTRL flag, just like all the other control related ioctls, otherwise the ioctl core won't know it also has to check whether v4l2_fh->ctrl_handler is non-zero before it can decide that this ioctl is not implemented. Caught by v4l2-compliance while I was testing the mem2mem_testdev driver. Signed-off-by:
-
- 14 Jul, 2012 1 commit
-
-
Mauro Carvalho Chehab authored
* v4l_for_linus: (31 commits) [media] Revert "[media] V4L: JPEG class documentation corrections" [media] s5p-fimc: Add missing FIMC-LITE file operations locking [media] omap3isp: preview: Fix contrast and brightness handling [media] omap3isp: preview: Fix output size computation depending on input format [media] winbond-cir: Initialise timeout, driver_type and allowed_protos [media] winbond-cir: Fix txandrx module info [media] cx23885: Silence unknown command warnings [media] cx23885: add support for HVR-1255 analog (cx23888 variant) [media] cx23885: make analog support work for HVR_1250 (cx23885 variant) [media] cx25840: fix vsrc/hsrc usage on cx23888 designs [media] cx25840: fix regression in HVR-1800 analog audio [media] cx25840: fix regression in analog support hue/saturation controls [media] cx25840: fix regression in HVR-1800 analog support [media] s5p-mfc: Fixed setup of custom controls in decoder and encoder [media] cx231xx: don't DMA to random addresses [media] em28xx: fix em28xx-rc load [media] dvb-core: Release semaphore on error path dvb_register_device() [media] s5p-fimc: Stop media entity pipeline if fimc_pipeline_validate fails [media] s5p-fimc: Fix compiler warning in fimc-lite.c [media] s5p-fimc: media_entity_pipeline_start() may fail ...
-
- 12 Jul, 2012 1 commit
-
-
Sakari Ailus authored
v4l2-common.h is a header file that's used in user space, thus it must be exported using header-y. Signed-off-by:
Sakari Ailus <sakari.ailus@iki.fi> Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Tested-by:
-
