Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

This patch adds the MPUSS OSWR (Open Switch Retention) support. The MPUSS
OSWR configuration is as below.
	- CPUx L1 and logic lost, MPUSS logic lost, L2 memory is retained

OMAP4460 onwards, MPUSS power domain doesn't support OFF state any more
anymore just like CORE power domain. The deepest state supported is OSWR.
On OMAP4430 secure devices too, MPUSS off mode can't be used because of
a bug which alters Ducati and Tesla states. Hence MPUSS off mode as an
independent state isn't supported on OMAP44XX devices.

Ofcourse when MPUSS power domain transitions to OSWR along
with device off mode, it eventually hits off state since memory
contents are lost.

Hence the MPUSS off mode independent state is not attempted without
device off mode. All the necessary infrastructure code for MPUSS
off mode is in place as part of this series.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

When MPUSS hits off-mode, L2 cache is lost. This patch adds L2X0
necessary maintenance operations and context restoration in the
low power code.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Add WakeupGen and secure GIC low power support to save and restore
it's registers. WakeupGen Registers are saved to pre-defined SAR RAM layout
and the restore is automatically done by hardware(ROM code) while coming
out of MPUSS OSWR or Device off state. Secure GIC is saved using secure
API and restored by hardware like WakeupGen.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

With OMAP4 suspend, idle and hotplug series, we no longer need
do_wfi() macro.

Remove the same.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

This patch adds MPUSS(MPU Sub System) power domain
CSWR(Close Switch Retention) support to system wide suspend.
For MPUSS power domain to hit retention(CSWR or OSWR), both
CPU0 and CPU1 power domains need to be in OFF or DORMANT state,
since CPU power domain CSWR is not supported by hardware
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Default arch_idle() isn't good enough for OMAP4 because of aync bridge errata
and necessity of NOPs post WFI to avoid speculative prefetch aborts.
Hence Use OMAP4 custom omap_do_wfi() hook for default idle.

Later in the series, async bridge errata work-around patch updates the
omap_do_wfi() with necessary interconnects barriers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

The SGI(Software Generated Interrupts) are not wakeup capable from
low power states. This is known limitation on OMAP4 and needs to be
worked around by using software forced clockdomain wake-up. CPU0 forces
the CPU1 clockdomain to software force wakeup.

More details can be found in OMAP4430 TRM - Version J
Section :
	4.3.4.2 Power States of CPU0 and CPU1
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Program non-boot CPUs to hit lowest supported power state
when it is off-lined using cpu hotplug framework.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Remove the __INIT from omap_secondary_startup() so that it can
be re-used for CPU hotplug.

While at this, remove the un-used AUXBOOT register reference.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

This patch adds the CPU0 and CPU1 off mode support. CPUX close switch
retention (CSWR) is not supported by hardware design.

The CPUx OFF mode isn't supported on OMAP4430 ES1.0

CPUx sleep code is common for hotplug, suspend and CPUilde.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

OMAP WakeupGen is the interrupt controller extension used along
with ARM GIC to wake the CPU out from low power states on
external interrupts.

The WakeupGen unit is responsible for generating the wakeup event
from the incoming interrupts and enable bits. It is implemented
in the MPU always ON power domain. During normal operation,
WakeupGen delivers the external interrupts directly to the GIC.

WakeupGen specification has one restriction as per Veyron version 1.6.
It is SW responsibility to program interrupt enabling/disabling
coherently in the GIC and in the WakeupGen enable registers. That is, a
given interrupt for a given CPU is either enable at both GIC and WakeupGen,
or disable at both, but no mix. That's the reason the WakeupGen is
implemented as an extension of GIC.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Allocate the memory to save secure ram context which needs
to be done when MPU is hitting OFF mode.

The ROM code expects a physical address to this memory
and hence use memblock APIs to reserve this memory as part
of .reserve() callback. Maximum size as per secure RAM requirements
is allocated.

To keep omap1 build working, omap-secure.h file is created
under plat-omap directory.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

On OMAP secure/emulation devices, certain APIs are exported by secure
code. Add an infrastructure so that relevant operations on secure
devices can be implemented using it.

While at this, rename omap44xx-smc.S to omap-smc.S since the common APIs
can be used on other OMAP's too.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Initialise hardware supervised mode for all clockdomains if it's
supported. Initiate sleep transition for other clockdomains,
if they are not being used.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

On OMAP4430 ES1.0, Power Management features are not supported.
Avoid omap4_pm_init() on ES1.0 silicon so that we can continue
to use same kernel binary to boot on all OMAP4 silicons.

The ES1.0 boot failure with OMAP4 PM series was because of
the clockdomain initialisation code. Hardware supervised
clockdomain mode isn't functional for all clockdomains
on OMAP4430 ES1.0 silicon so avoid the same.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

As per OMAP4430 TRM, the dynamic dependency between MPUSS -> EMIF
and MPUSS -> L4PER/L3_* and DUCATI -> L3_* clockdomains is enable
by default. Refer register CM_MPU_DYNAMICDEP description for details.

But these dynamic dependencies doesn't work as expected. The hardware
recommendation is to enable static dependencies for above clockdomains.
Without this, system locks up or randomly crashes.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

This patch adds SAR RAM support on OMAP4430. SAR RAM used to save
and restore the HW context in low power modes.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

This patch exports APIs to get base address for GIC
distributor, CPU interface, SCU and PL310 L2 Cache which
are used in OMAP4 PM code.

This was suggested by Kevin Hilman <khilman@ti.com> during
OMAP4 PM code review.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

OMAP4 L2X0 initialisation code uses BUG_ON() for the ioremap()
failure scenarios.

Use WARN_ON() instead and allow graceful function exits.

This was suggsted by Kevin Hilman <khilman@ti.com> during
OMAP4 PM code review.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

ARM restart changes needed changes to common.h to make it local.
This conflicted with v3.2-rc4 DSS related hwmod changes that
git mergetool was not able to handle.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Otherwise we get the following error:

In function 'omap_init_consistent_dma_size':
error: implicit declaration of function 'init_consistent_dma_size'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Merge branch 'for-rmk' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into devel-stable

Conflicts:
	arch/arm/common/gic.c
	arch/arm/plat-omap/include/plat/common.h

Fix the below build break by including common.h

arch/arm/mach-omap2/cpuidle34xx.c: In function 'omap3_enter_idle':
arch/arm/mach-omap2/cpuidle34xx.c:117: error: implicit declaration of function 'omap_irq_pending'
make[1]: *** [arch/arm/mach-omap2/cpuidle34xx.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix the build break by adding the necessary irq functions to
common header.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Merge branch 'irqchip-consolidation' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into devel-stable

This patch introduces .enable_irq and .disable_irq into
struct arm_pmu_platdata, so platform specific irq enablement
can be handled after request_irq, and platform specific irq
disablement can be handled before free_irq.

This patch is for support of  pmu irq routed from CTI on omap4.
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

OMAP4 uses cross trigger interface(CTI) to route
performance monitor irq to GIC, so introduce cti
helpers to make access for cti easily.
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

armpmu_get_max_events is only called from perf_num_counters, so we can
inline it there. It existed as a separate entity as a hangover from
the original perf-based oprofile implementation.
Signed-off-by: Will Deacon <will.deacon@arm.com>

Commit 8f622422 ("perf events: Add generic front-end and back-end
stalled cycle event definitions") added two new ABI events for counting
stalled cycles.

This patch adds support for these new events to the ARM perf
implementation.

Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

This patch updates the ARMv7 perf event numbers so that:

(1) A consistent naming scheme is used between different CPUs.

(2) Only events actually used by Linux are described.

(3) Where possible, architected events are used in preference to
    CPU-specific events.

This results in the removal of a load of unused, hardcoded data and
makes it more clear as to which events are supported on each PMU.

Cc: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Trivial fix to fix below build error:

  CC      arch/arm/mach-exynos/mach-universal_c210.o
arch/arm/mach-exynos/mach-universal_c210.c:24: error: expected identifier or '(' before '<' token
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Fix below build error:
  CC      arch/arm/mach-exynos/cpu.o
arch/arm/mach-exynos/cpu.c: In function 'exynos4_init_irq':
arch/arm/mach-exynos/cpu.c:245: error: 'gic_bank_offset' undeclared (first use in this function)
arch/arm/mach-exynos/cpu.c:245: error: (Each undeclared identifier is reported only once
arch/arm/mach-exynos/cpu.c:245: error: for each function it appears in.)
arch/arm/mach-exynos/cpu.c:243: warning: unused variable 'bank_offset'
make[1]: *** [arch/arm/mach-exynos/cpu.o] Error 1
make: *** [arch/arm/mach-exynos] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2: (31 commits)
  ocfs2: avoid unaligned access to dqc_bitmap
  ocfs2: Use filemap_write_and_wait() instead of write_inode_now()
  ocfs2: honor O_(D)SYNC flag in fallocate
  ocfs2: Add a missing journal credit in ocfs2_link_credits() -v2
  ocfs2: send correct UUID to cleancache initialization
  ocfs2: Commit transactions in error cases -v2
  ocfs2: make direntry invalid when deleting it
  fs/ocfs2/dlm/dlmlock.c: free kmem_cache_zalloc'd data using kmem_cache_free
  ocfs2: Avoid livelock in ocfs2_readpage()
  ocfs2: serialize unaligned aio
  ocfs2: Implement llseek()
  ocfs2: Fix ocfs2_page_mkwrite()
  ocfs2: Add comment about orphan scanning
  ocfs2: Clean up messages in the fs
  ocfs2/cluster: Cluster up now includes network connections too
  ocfs2/cluster: Add new function o2net_fill_node_map()
  ocfs2/cluster: Fix output in file elapsed_time_in_ms
  ocfs2/dlm: dlmlock_remote() needs to account for remastery
  ocfs2/dlm: Take inflight reference count for remotely mastered resources too
  ocfs2/dlm: Cleanup dlm_wait_for_node_death() and dlm_wait_for_node_recovery()
  ...

The dqc_bitmap field of struct ocfs2_local_disk_chunk is 32-bit aligned,
but not 64-bit aligned.  The dqc_bitmap is accessed by ocfs2_set_bit(),
ocfs2_clear_bit(), ocfs2_test_bit(), or ocfs2_find_next_zero_bit().  These
are wrapper macros for ext2_*_bit() which need to take an unsigned long
aligned address (though some architectures are able to handle unaligned
address correctly)

So some 64bit architectures may not be able to access the dqc_bitmap
correctly.

This avoids such unaligned access by using another wrapper functions for
ext2_*_bit().  The code is taken from fs/ext4/mballoc.c which also need to
handle unaligned bitmap access.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Joel Becker <jlbec@evilplan.org>

* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
  ARM: 7182/1: ARM cpu topology: fix warning
  ARM: 7181/1: Restrict kprobes probing SWP instructions to ARMv5 and below
  ARM: 7180/1: Change kprobes testcase with unpredictable STRD instruction
  ARM: 7177/1: GIC: avoid skipping non-existent PPIs in irq_start calculation
  ARM: 7176/1: cpu_pm: register GIC PM notifier only once
  ARM: 7175/1: add subname parameter to mfp_set_groupg callers
  ARM: 7174/1: Fix build error in kprobes test code on Thumb2 kernels
  ARM: 7172/1: dma: Drop GFP_COMP for DMA memory allocations
  ARM: 7171/1: unwind: add unwind directives to bitops assembly macros
  ARM: 7170/2: fix compilation breakage in entry-armv.S
  ARM: 7168/1: use cache type functions for arch_get_unmapped_area
  ARM: perf: check that we have a platform device when reserving PMU
  ARM: 7166/1: Use PMD_SHIFT instead of PGDIR_SHIFT in dma-consistent.c
  ARM: 7165/2: PL330: Fix typo in _prepare_ccr()
  ARM: 7163/2: PL330: Only register usable channels
  ARM: 7162/1: errata: tidy up Kconfig options for PL310 errata workarounds
  ARM: 7161/1: errata: no automatic store buffer drain
  ARM: perf: initialise used_mask for fake PMU during validation
  ARM: PMU: remove pmu_init declaration
  ARM: PMU: re-export release_pmu symbol to modules

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix meta data raid-repair merge problem
  Btrfs: skip allocation attempt from empty cluster
  Btrfs: skip block groups without enough space for a cluster
  Btrfs: start search for new cluster at the beginning
  Btrfs: reset cluster's max_size when creating bitmap
  Btrfs: initialize new bitmaps' list
  Btrfs: fix oops when calling statfs on readonly device
  Btrfs: Don't error on resizing FS to same size
  Btrfs: fix deadlock on metadata reservation when evicting a inode
  Fix URL of btrfs-progs git repository in docs
  btrfs scrub: handle -ENOMEM from init_ipath()