- 18 Feb, 2010 16 commits
-
-
Joe Perches authored
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt Remove #define PFX Use pr_<level> Use netdev_<level> Use netif_<level> Convert formats like %8.8 to %08 Remove periods from formats Coalesce long formats Use print_hex_dump Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Joe Perches authored
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt Remove #define PFX Use pr_<level> Use netdev_<level> Use netif_<level> Remove periods from formats Coalesce long formats Signed-off-by:
-
Matt Carlson authored
This patch updates the tg3 version to 3.108. Signed-off-by:
Matt Carlson <mcarlson@broadcom.com> Reviewed-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
-
Matt Carlson authored
This patch pushes phylib definitions out to phylib headers. For phy IDs, this removes some code duplication. Signed-off-by:
-
Matt Carlson authored
The phylib presents the phy ID in a different format than the one tg3 has traditionally used. To highlight the distinction, this patch prepends the tg3 native phy ID format with TG3. Signed-off-by:
-
Matt Carlson authored
This patch reformats the SSID to phy ID table, replacing constants with preprocessor definitions. This patch is also prep work for the following patch, which will push line lengths beyond 80 chars. Signed-off-by:
-
Matt Carlson authored
The phy address will not change after it has been identified. Move the discovery code to a location that only gets executed once. Signed-off-by:
-
Matt Carlson authored
This patch adds an inverted "jumbo ring enable" test and jumps to the exit if it succeeds. The change reduces the indent level of the remaining code making it more readable. Signed-off-by:
-
Matt Carlson authored
The STD part of this preprocessor definition is a bit of a misnomer. This flag is a coarse control of the RGMII inband status facilities. This patch renames the definition to be more accurate. Signed-off-by:
-
Matt Carlson authored
This patch adds 57765 asic partno entries for the path executed if VPD is not present in NVRAM. Signed-off-by:
-
Matt Carlson authored
This patch loosens the restriction that the phylib interface must be up and running to change the flow control parameters. Signed-off-by:
-
Matt Carlson authored
This patch adds new offsets to the bootcode version extraction code to support NVRAM format versions 4 and 5. Signed-off-by:
-
Matt Carlson authored
This patch adds the 57791 and 57795 to the list of devices that only support 10 and 100 Mbps speeds. Signed-off-by:
-
Matt Carlson authored
Michael Chan noted that there is nothing in the code that would prevent the compiler from delaying the access of the "mapping" member of the newly arrived packet until much later. If this happened after the skb = NULL assignment, it is possible for the driver to pass a bad dma_addr value to pci_unmap_single(). To enforce this ordering, we need a write memory barrier. The pairing read memory barrier already exists in tg3_rx_prodring_xfer() under the comments starting with "Ensure that updates to the...". Signed-off-by:
-
Michael S. Tsirkin authored
This patch adds Linux Socket Filter support to tun driver. Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Michael S. Tsirkin authored
Export sk_attach_filter/sk_detach_filter routines, so that tun module can use them. Signed-off-by:
-
- 17 Feb, 2010 24 commits
-
-
Jiri Pirko authored
Signed-off-by:
Jiri Pirko <jpirko@redhat.com> Signed-off-by:
-
Jiri Pirko authored
Removed whole t3_rx_mode structure and appropriate helpers cause they are no longer needed. Signed-off-by:
-
kirjanov@gmail.com authored
Use phy_find_first() function instead of manual lookup. Signed-off-by:
Denis Kirjanov <kirjanov@gmail.com> Reviewed-by:
-
Ajit Khaparde authored
Traffic (tcp) doesnot start on a vlan interface when gro is enabled. Even the tcp handshake was not taking place. This is because, the eth_type_trans call before the netif_receive_skb in napi_gro_finish() resets the skb->dev to napi->dev from the previously set vlan netdev interface. This causes the ip_route_input to drop the incoming packet considering it as a packet coming from a martian source. I could repro this on 2.6.32.7 (stable) and 2.6.33-rc7. With this fix, the traffic starts and the test runs fine on both vlan and non-vlan interfaces. CC: Herbert Xu <herbert@gondor.apana.org.au> CC: Patrick McHardy <kaber@trash.net> Signed-off-by:
Ajit Khaparde <ajitk@serverengines.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
kirjanov@gmail.com authored
Fix missing validate_addr hook. Signed-off-by:
-
Kristoffer Glembo authored
Adds device driver for Aeroflex Gaisler 10/100 and 10/100/1G Ethernet MAC IP cores. Signed-off-by:
Kristoffer Glembo <kristoffer@gaisler.com> Signed-off-by:
-
Simon Kagstrom authored
Reduces CPU utilization significantly with sendfile for example. Signed-off-by:
Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by:
-
Jeff Mahoney authored
This patch removes D-Link DGE-550T PCI ID (1186:4000) from the ipg driver. The ipg driver is for IP2000-based cards and the DGE-550T is a DL2000-based card. The driver loads and works for a few moments, but once a real workload is applied it stops operating. The ipg driver claimed this ID since it was introduced in 2.6.24 and it's forced many users to blacklist it. The correct driver for this hardware is the dl2k driver, which has been claiming this PCI ID since the 2.4 days. Signed-off-by:
Jeff Mahoney <jeffm@suse.com> Signed-off-by:
-
David S. Miller authored
As reported by Alexey Dobriyan: -------------------- setkey now takes several seconds to run this simple script and it spits "recv: Resource temporarily unavailable" messages. #!/usr/sbin/setkey -f flush; spdflush; add A B ipcomp 44 -m tunnel -C deflate; add B A ipcomp 45 -m tunnel -C deflate; spdadd A B any -P in ipsec ipcomp/tunnel/192.168.1.2-192.168.1.3/use; spdadd B A any -P out ipsec ipcomp/tunnel/192.168.1.3-192.168.1.2/use; -------------------- Obviously applications want the events even when the table is empty. So we cannot make this behavioral change. Signed-off-by: -
Riccardo Ghetta authored
Adds half-duplex specific setup code (taken from SiS own GPL driver). Without those, half-duplex connections are very unreliable, often working on small transfers and failing after a while. Signed-off-by:
Riccardo Ghetta <birrachiara@tin.it> Signed-off-by:
-
Ben Hutchings authored
The n-tuple list should be flushed if and only if the ETH_RESET_FILTER flag is set and the driver is able to reset filtering/flow direction hardware without also resetting a component whose flag is not set. This test is best left to the driver. Signed-off-by:
Ben Hutchings <bhutchings@solarflare.com> Signed-off-by:
-
Vladislav Zolotarov authored
Updated release version and date: 1.52.1-6 and 2010/02/16 Signed-off-by:
Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by:
Eilon Greenstein <eilong@broadcom.com> Signed-off-by:
-
Vladislav Zolotarov authored
Switch to the new firmware version (5.2.13). Signed-off-by:
-
Vladislav Zolotarov authored
New firmware version (5.2.13). Signed-off-by:
-
Vladislav Zolotarov authored
Bug fix: Use the last unicast entry in CAM in bnx2x_test_int(). Relevant for 57710 only. Author: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by:
Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by:
-
Vladislav Zolotarov authored
Bug fix: Do not allow enabling LRO if disable_tpa=1. Signed-off-by:
-
Vladislav Zolotarov authored
Bug fix: clean up MCP state in case of error in bnx2x_init_hw(). Author: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by:
-
Vladislav Zolotarov authored
Bug fix: Properly release allocated MSI-X/MSI vectors if ifup failed due to lack of memory. Signed-off-by:
-
Joe Perches authored
Convert from: if (netif_msg_<foo>(priv)) dev_<level>(dev... to netif_<level>(priv, foo, dev... Also convert a few: if (i < REG_TIMEOUT) { etc... return ret; } to if (i >= REG_TIMEOUT) goto fail; etc... return ret; Signed-off-by: -
Joe Perches authored
These macros are too similar to the dev_<level> equivalents but take a usbnet * argument. Convert them to the recently introduced netdev_<level> macros and remove the old macros. The old macros had "\n" appended to the format string. Add the "\n" to the converted uses. Some existing uses of the dev<foo> macros in cdc_eem.c probably mistakenly had trailing "\n". No "\n" added there. Fix net1080 this/other log message inversion. Signed-off-by:
-
Sathya Perla authored
Signed-off-by:
Sathya Perla <sathyap@serverengines.com> Signed-off-by:
-
Sathya Perla authored
The flush compl (compl with numfrags == 0; no data) is rcvd from hw to indicate completion of RXQ destory operation. Fix the RX path to not process it as RX data. Signed-off-by:
-
Sathya Perla authored
When an MCC cmd is issued (via a netdev/ethtool op) while the device is not open, the MCC CQ gets processed but the EQ is not processed (as isr is not registered.) This can cause the EQ to become full. So, while the device is not open, CQ must not be re-armed to prevent EQ entries. Signed-off-by:
-
Sathya Perla authored
Introduce unlikely() for skb alloc failure and vlanf checks... Signed-off-by:
-
