- 25 May, 2011 40 commits
-
-
Arindam Nath authored
This patch adds support for setting UHS-I bus speed mode during UHS-I initialization procedure. Since both the host and card can support more than one bus speed, we select the highest speed based on both of their capabilities. First we set the bus speed mode for the card using CMD6 mode 1, and then we program the host controller to support the required speed mode. We also set High Speed Enable in case one of the UHS-I modes is selected. We take care to reset SD clock before setting UHS mode in the Host Control2 register, and then re-enable it as per the Host Controller spec v3.00. We then set the clock frequency for the UHS-I mode selected. Tested by Zhangfei Gao with a Toshiba uhs card and general hs card, on mmp2 in SDMA mode. Signed-off-by:
Arindam Nath <arindam.nath@amd.com> Reviewed-by:
Philip Rakity <prakity@marvell.com> Tested-by:
Zhangfei Gao <zhangfei.gao@marvell.com> Signed-off-by:
Chris Ball <cjb@laptop.org>
-
Arindam Nath authored
As per Host Controller spec v3.00, we reset SDCLK before setting High Speed Enable, and then set it back to avoid generating clock gliches. Before enabling SDCLK again, we make sure the clock is stable, so we use sdhci_set_clock(). Tested by Zhangfei Gao with a Toshiba uhs card and general hs card, on mmp2 in SDMA mode. Signed-off-by:
-
Arindam Nath authored
This patch adds support for setting driver strength during UHS-I initialization procedure. Since UHS-I cards set S18A (bit 24) in response to ACMD41, we use this as a base for UHS-I initialization. We modify the parameter list of mmc_sd_get_cid() so that we can save the ROCR from ACMD41 to check whether bit 24 is set. We decide whether the Host Controller supports A, C, or D driver type depending on the Capabilities register. Driver type B is suported by default. We then set the appropriate driver type for the card using CMD6 mode 1. As per Host Controller spec v3.00, we set driver type for the host only if Preset Value Enable in the Host Control2 register is not set. SDHCI_HOST_CONTROL has been renamed to SDHCI_HOST_CONTROL1 to conform to the spec. Tested by Zhangfei Gao with a Toshiba uhs card and general hs card, on mmp2 in SDMA mode. Signed-off-by:
-
Arindam Nath authored
SD cards which conform to Physical Layer Spec v3.01 can support additional Bus Speed Modes, Driver Strength, and Current Limit other than the default values. We use CMD6 mode 0 to read these additional card functions. The values read here will be used during UHS-I initialization steps. Tested by Zhangfei Gao with a Toshiba uhs card and general hs card, on mmp2 in SDMA mode. Signed-off-by:
-
Arindam Nath authored
Host Controller v3.00 adds another Capabilities register. Apart from other things, this new register indicates whether the Host Controller supports SDR50, SDR104, and DDR50 UHS-I modes. The spec doesn't mention about explicit support for SDR12 and SDR25 UHS-I modes, so the Host Controller v3.00 should support them by default. Also if the controller supports SDR104 mode, it will also support SDR50 mode as well. So depending on the host support, we set the corresponding MMC_CAP_* flags. One more new register. Host Control2 is added in v3.00, which is used during Signal Voltage Switch procedure described below. Since as per v3.00 spec, UHS-I supported hosts should set S18R to 1, we set S18R (bit 24) of OCR before sending ACMD41. We also need to set XPC (bit 28) of OCR in case the host can supply >150mA. This support is indicated by the Maximum Current Capabilities register of the Host Controller. If the response of ACMD41 has both CCS and S18A set, we start the signal voltage switch procedure, which if successfull, will switch the card from 3.3V signalling to 1.8V signalling. Signal voltage switch procedure adds support for a new command CMD11 in the Physical Layer Spec v3.01. As part of this procedure, we need to set 1.8V Signalling Enable (bit 3) of Host Control2 register, which if remains set after 5ms, means the switch to 1.8V signalling is successfull. Otherwise, we clear bit 24 of OCR and retry the initialization sequence. When we remove the card, and insert the same or another card, we need to make sure that we start with 3.3V signalling voltage. So we call mmc_set_signal_voltage() with MMC_SIGNAL_VOLTAGE_330 set so that we are back to 3.3V signalling voltage before we actually start initializing the card. Tested by Zhangfei Gao with a Toshiba uhs card and general hs card, on mmp2 in SDMA mode. Signed-off-by:
-
John Calixto authored
Allows appropriately-privileged applications to send CMD (normal) and ACMD (application-specific; preceded with CMD55) commands to cards/devices on the mmc bus. This is primarily useful for enabling the security functionality built in to every SD card. It can also be used as a generic passthrough (e.g. to enable virtual machines to control mmc bus devices directly). However, this use case has not been tested rigorously. Generic passthrough testing was only conducted for a few non-security opcodes to prove the feasibility of the passthrough. Since any opcode can be sent using this passthrough, it is very possible to render the card/device unusable. Applications that use this ioctl must have CAP_SYS_RAWIO. Security commands tested on TI PCIxx12 (SDHCI), Sigma Designs SMP8652 SoC, TI OMAP3621/OMAP3630 SoC, Samsung S5PC110 SoC, Qualcomm MSM7200A SoC. Signed-off-by:
John Calixto <john.calixto@modsystems.com> Reviewed-by:
Andrei Warkentin <andreiw@motorola.com> Reviewed-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Rabin Vincent authored
To avoid lockdep warnings: BUG: key dc90a520 not in .data! ------------[ cut here ]------------ WARNING: at /home/rabin/kernel/arm/kernel/lockdep.c:2701 sysfs_add_file_mode+0x4c/0xb0() Modules linked in: [<c004b5d8>] (unwind_backtrace+0x0/0xe4) from [<c0074f20>] (warn_slowpath_common+0x4c/0x64) [<c0074f20>] (warn_slowpath_common+0x4c/0x64) from [<c0074f50>] (warn_slowpath_null+0x18/0x1c) [<c0074f50>] (warn_slowpath_null+0x18/0x1c) from [<c0157fec>] (sysfs_add_file_mode+0x4c/0xb0) [<c0157fec>] (sysfs_add_file_mode+0x4c/0xb0) from [<c02d61e4>] (mmc_add_disk+0x40/0x64) [<c02d61e4>] (mmc_add_disk+0x40/0x64) from [<c02d64cc>] (mmc_blk_probe+0x188/0x1fc) [<c02d64cc>] (mmc_blk_probe+0x188/0x1fc) from [<c02ce820>] (mmc_bus_probe+0x14/0x18) ... Signed-off-by:
Rabin Vincent <rabin@rab.in> Signed-off-by:
-
Takashi Iwai authored
On HP laptops with JMicron 388 chip, the write-locked SD card isn't detected correctly as read-only in many cases. This is because the PRESENT_STATE register becomes unsable just after plugging, and it returns the WRITE_PROTECT bit wrongly at the first read. This patch fixes the read-only detection by adding a new sdhci quirk indicating to check the register more intensively with a relatively long delay. The patch is tested with 2.6.39-rc4 kernel. Cc: Aries Lee <arieslee@jmicron.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Andrei Warkentin authored
With the hardware partitions support (which represent additional logical devices present on MMC), devidx does not correspond with index used to form /dev/mmcblkX names. So use an additional allocated index for device names. Signed-off-by:
-
Philip Rakity authored
Marvell pxa controllers have private registers that may need to be modified before and after a reset is done. For example, the SD reset operation, RESET_ALL, will reset the private registers to their default state. This will cause the clock adjustment registers that may have been programmed to have incorrect values. RESET_DATA sometimes needs to be delayed before the reset is done (depending on SoC) to enable any transactions being handled by the SDIO card to be completed. Needed in pre SD 3.0 silicon to handle clock gating. Implement hooks to allow this to happen. Signed-off-by:
-
Mark Brown authored
Commit 373e6a (mmc: sdhci: R1B command handling + MMC_CAP_ERASE) moved the handling of SDHCI_QUIRK_TIMEOUT_USES_SDCLK from sdhci_calc_timeout() to sdhci_add_host(). This causes division by zero errors on at least the S3C SDHCI controller as the quirk implementation needs host->clock set to work but host->clock has not been set when sdhci_add_host() is called. Fix this by backing out that portion of the change, the clock may vary at runtime anyway. It does occur to me that we may want to move the quirk to where we set the clock but this seems more invasive and I'm concerned about undesirable side effects. Signed-off-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Andrei Warkentin <andreiw@motorola.com> Signed-off-by:
-
Chris Ball authored
Converts from: struct mmc_request mrq; memset(&mrq, 0, sizeof(struct mmc_request)); to: struct mmc_request mrq = {0}; because it's shorter, as performant, and easier to work out whether initialization has happened. Signed-off-by: -
Chris Ball authored
Converts from: struct mmc_data data; memset(&data, 0, sizeof(struct mmc_data)); to: struct mmc_data data = {0}; because it's shorter, as performant, and easier to work out whether initialization has happened. Signed-off-by: -
Chris Ball authored
Converts from: struct mmc_command cmd; memset(&cmd, 0, sizeof(struct mmc_command)); to: struct mmc_command cmd = {0}; because it's shorter, as performant, and easier to work out whether initialization has happened. Signed-off-by: -
Chris Ball authored
mmc_blk_issue_rw_rq did not zero out mmc_command on stack. Signed-off-by: -
Chris Ball authored
mmc_send_if_cond did not zero out mmc_command on stack. Signed-off-by: -
Andrei Warkentin authored
mmc_cmd_app did not zero out mmc_command on stack. Reported-by:
Chuanxiao Dong <chuanxiao.dong@intel.com> Signed-off-by:
-
Andrei Warkentin authored
CMD38 argument is passed through EXT_CSD[113]. Signed-off-by:
-
Mikko Vinni authored
Some SD host controllers (noticed on an integrated JMicron SD reader on an HP Pavilion dv5-1250eo laptop) don't update the dma address register before signaling a dma interrupt due to a dma boundary. Update the register manually to the next boundary (by default 512KiB), at which the transfer stopped. As long as each transfer is at most 512KiB in size (guaranteed by a BUG_ON in sdhci_prepare_data()) and the boundary is kept at the default value, this fix is needed at most once per transfer. Smaller boundaries are taken care of by counting the transferred bytes. Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=28462Signed-off-by:
Mikko Vinni <mmvinni@yahoo.com> Signed-off-by:
-
Andrei Warkentin authored
Block quirks implemented using core/quirks.c support. Signed-off-by:
-
Andrei Warkentin authored
Allows device MMC boot partitions to be accessed. MMC partitions are treated effectively as separate block devices on the same MMC card. Signed-off-by:
-
Andrei Warkentin authored
Move host claim/release into mmc_blk_issue_rq. (This is helpful so that selecting partition only has to happen in one place for these commands.) Signed-off-by:
-
Andrei Warkentin authored
CMD6 is an R1B-type command, where DAT is used as busy. Depending on register written using CMD6, timeout value can be different as per spec. Signed-off-by:
-
Andrei Warkentin authored
ERASE command needs R1B response, so fix R1B-type command handling for SDHCI controller. For non-DAT commands using a busy response, the cmd->cmd_timeout_ms (in ms) field is used for timeout calculations. Based on patch by Chuanxiao Dong <chuanxiao.dong@intel.com> Signed-off-by:
-
Andrei Warkentin authored
Renames erase_timeout to cmd_timeout_ms inside struct mmc_command. First step to making host honor timeouts for non-data-transfer commands. Cleans up erase timeout code. Signed-off-by:
-
Randy Dunlap authored
Fix data truncation warnings: .manfid is not unsigned long: drivers/mmc/core/quirks.c:36: warning: large integer implicitly truncated to unsigned type drivers/mmc/core/quirks.c:40: warning: large integer implicitly truncated to unsigned type drivers/mmc/core/quirks.c:43: warning: large integer implicitly truncated to unsigned type drivers/mmc/core/quirks.c:46: warning: large integer implicitly truncated to unsigned type Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
Andrei Warkentin authored
The current mechanism is SDIO-only. This allows us to create function-specific quirks, without creating messy Kconfig dependencies, or polluting core/ with function-specific code. Signed-off-by:
-
Wolfram Sang authored
led_trigger_register_simple() allocates memory which must not be leaked in the error-path of mmc_add_host. Move it past the only error-check in the function. Signed-off-by:
Wolfram Sang <w.sang@pengutronix.de> Signed-off-by:
-
Ameya Palande authored
This patch fixes 21 errors and 6 warnings reported by checkpatch.pl. Signed-off-by:
Ameya Palande <2ameya@gmail.com> Reviewed-by:
-
Ohad Ben-Cohen authored
The wl12xx device supports disconnecting the pull-up resistor on CD/DAT[3] (pin 1) of the card. Tell SDIO core to disconnect that resistor during card init, since we don't need it at that point (and anyway all hosts shall provide pull-up resistors on all data lines DAT[3:0] as described in section 6 of the SD physical specification). As a result, this may save some power, but it's also generally healthy since it prevents both ends from pulling up that pin, which results in undesirable asymmetric physical bus. Signed-off-by:
Ohad Ben-Cohen <ohad@wizery.com> Signed-off-by:
-
Ohad Ben-Cohen authored
006ebd5d introduced sdio_disable_cd(), which disconnects the pull-up resistor on CD/DAT[3] (pin 1) of the card. Make it possible to start using sdio_disable_cd() by introducing MMC_QUIRK_DISABLE_CD. Signed-off-by:
-
Ohad Ben-Cohen authored
Tell SDIO core to ignore the standard SDIO function interface codes indicated by the wl1271. This is required because the wl1271 erroneously indicates its first function as a standard Bluetooth SDIO interface, and that drives btsdio mad. Signed-off-by:
-
Ohad Ben-Cohen authored
Introduce MMC_QUIRK_NONSTD_FUNC_IF to ignore the "SDIO Standard Function interface code" as indicated by the card's FBR, and instead treat all functions as non-standard interfaces. This is required to prevent standard drivers from facing errors when trying to communicate with SDIO cards that erroneously indicate standard function interface codes. Signed-off-by:
-
Ohad Ben-Cohen authored
6b5eda36 followed SDIO spec part E1 section 8, which states that in case SDIO interrupts are being used to wake up a suspended host, then it is required to switch to 1-bit mode before stopping the clock. Before switching to 1-bit mode (or back to 4-bit mode on resume), make sure that SDIO interrupts are really being used to wake the host. This is helpful for devices which have an external irq line (e.g. wl1271), and do not use SDIO interrupts to wake up the host. In this case, switching to 1-bit mode (and back to 4-bit mode on resume) is not necessary. Reported-by:
Eliad Peller <eliad@wizery.com> Signed-off-by:
-
Ohad Ben-Cohen authored
mmc_card_is_powered_resumed is a mouthful; instead, simply use mmc_card_keep_power, which also better explains the purpose of the macro. Employ mmc_card_keep_power() where possible. Signed-off-by:
-
Andrei Warkentin authored
Allows reliable writes to be used for MMC writes. Reliable writes are used to service write REQ_FUA/REQ_META requests. Handles both the legacy and the enhanced reliable write support in MMC cards. Signed-off-by:
-
Shawn Guo authored
This config option is used to decide whether tegra sdhci support should be build into the sdhci-platform module. So setting it 'm' is nonsense, since we can't build part of an module as a module. The effect for 'm' will probably be the same as for 'n'. Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
Venkat Rao authored
Enable fast bcm4329 WIFI suspend/resume on Tegra2 board. This patch allows the mach-tegra support to tell the tegra MMC host controller to NOT turn off power for the MMC controller the WIFI part lives behind. Thus bcm4329 firmware doesn't need to be reloaded. Signed-off-by:
Venkat Rao <vrao@broadcom.com> Tested-by:
Grant Grundler <grundler@chromium.org> Reviewed-by:
Olof Johansson <olof@lixom.net> Acked-by:
-
John Ogness authored
There is no need to disable irq's when using the sg_copy_*_buffer() functions because those functions do that already. There are also no races for the mm_queue struct here that would require the irq's to be disabled before calling sg_copy_*_buffer(). Signed-off-by:
John Ogness <john.ogness@linutronix.de> Signed-off-by:
-
Philip Rakity authored
uBoot sometimes leaves eMMC pointing to the private boot partition. Ensure we always start looking at the user partition. Signed-off-by:
Bruce Clemens <bpclemens@marvell.com> Signed-off-by:
Mark F. Brown <markb@marvell.com> Signed-off-by:
-
