The silead touch-controller ICs use a different firmware per digitizer /
tablet model. So there are going to be quite a few of then and they really
should be under a separate subdir.

This commit prefixes the default firmware names with "silead/" just like
we are already doing for devicetree specified firmware names.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The driver has supported touchscreen-fw-name to specify the firmware to
load since it has been merged, but this was omitted from the dt-binding
documentation.

During review of adding touchscreen-fw-name to the binding documentation
it was brought up that there is a standard property name called
"firmware-name" for this, which should be used.

Since there are no users of touchscreen-fw-name yet, this commit
adds documentation of "firmware-name" to the dt-binding documentation
and switches the driver over to use this.

This commit also makes the driver add a "silead/" prefix to the
firmware name from dt before calling request_firmware. That the
firmware files are stored under /lib/firmware/silead under Linux
is an implementation detail and does not belong in devicetree.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

ADS7846 regulator is disabled twice in a row in ads7846_remove(). Valid
one is in ads7846_disable().

Removing the ads7846 module causes warning about unbalanced disables.

  ...
  WARNING: CPU: 0 PID: 29269 at drivers/regulator/core.c:2251 _regulator_disable+0xf8/0x130
  unbalanced disables for vads7846
  CPU: 0 PID: 29269 Comm: rmmod Tainted: G      D W       4.7.0+ #3
  Hardware name: HTC Magician
  ...
    show_stack+0x10/0x14
    __warn+0xd8/0x100
    warn_slowpath_fmt+0x38/0x48
    _regulator_disable+0xf8/0x130
    regulator_disable+0x34/0x60
    ads7846_remove+0x58/0xd4 [ads7846]
    spi_drv_remove+0x1c/0x34
    __device_release_driver+0x84/0x114
    driver_detach+0x8c/0x90
    bus_remove_driver+0x5c/0xc8
    SyS_delete_module+0x1a0/0x238
    ret_fast_syscall+0x0/0x38
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The map_offset variable is specific to the register and needs to be reset
in the loop. Otherwise, subsequent register's subpacket maps will have
their bits set at the wrong index.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Nitin Chaudhary <nitinchaudhary1289@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Commit fe6b0dfa ("Input: tegra-kbc - use reset framework")
accidentally converted _deassert to _assert, so there is no code
to wake up this hardware.

Fixes: fe6b0dfa ("Input: tegra-kbc - use reset framework")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The silead code is using devm_foo for everything (and does not free
any resources). Except that it is using gpiod_get instead of
devm_gpiod_get (but is not freeing the gpio_desc), change this
to use devm_gpiod_get so that the gpio will be properly released.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The commit 40974618 ("Input: i8042 - break load dependency ...")
correctly set up ps2_cmd_mutex pointer for the KBD port but forgot to do
the same for AUX port(s), which results in communication on KBD and AUX
ports to clash with each other.

Fixes: 40974618 ("Input: i8042 - break load dependency ...")
Reported-by: Bruno Wolff III <bruno@wolff.to>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

buf[0] is an unsigned char.  touch_nr is an int.  The test for negative
here doesn't make sense so I have removed it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The newly added sis_i2c driver fails to link without the CRC_ITU_T
driver enabled:

drivers/input/touchscreen/sis_i2c.o: In function `sis_ts_irq_handler':
sis_i2c.c:(.text+0xc0): undefined reference to `crc_itu_t'

This adds a Kconfig select statement.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: a485cb03 ("Input: add driver for SiS 9200 family I2C touchscreen controllers")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Prepare second round of input updates for 4.8 merge window.

This is a driver for SiS 9200 family touchscreen controllers using I2C bus.
Signed-off-by: Mika Penttilä <mika.penttila@nextfour.com>
Acked-by: Tammy Tseng <tammy_tseng@sis.com>
Acked-by: Yuger Yu <yuger_yu@sis.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

"calibrate" attribute does not provide "show" methods and thus we should
not mark it as readable.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Some ASUS laptops were shipped with touchpads that require to be woken up
first, before trying to switch them into absolute reporting mode, otherwise
touchpad would fail to work while flooding the logs with:

	elan_i2c i2c-ELAN1000:00: invalid report id data (1)

Among affected devices are Asus E202SA, N552VW, X456UF, UX305CA, and
others. We detect such devices by checking the IC type and product ID
numbers and adjusting order of operations accordingly.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Reported-by: Chris Chiu <chiu@endlessm.com>
Reported-by: Vlad Glagolev <stealth@vaygr.net>
Tested-by: Vlad Glagolev <stealth@vaygr.net>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This driver adds support for Silead touchscreens. It has been tested
with GSL1680 and GSL3680 touch panels.

It supports ACPI and device tree enumeration. Screen resolution,
the maximum number of fingers supported and firmware name are
configurable.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Daniel Jansen <djaniboe@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The use of mixed psmouse_printk() and printk creates 2 lines in the log,
while the use of %*ph solves everything.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

It's not advisable to use this encoding, but to support existing devices
add support for this to the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

When the USB wireless adapter is suspended, the controllers
lose their connection. This causes them to start flashing
their LED rings and searching for the wireless adapter
again, wasting the controller's battery power.

Instead, we will tell the controllers to power down when
we suspend. This mirrors the behavior of the controllers
when connected to the console itself and how the official
Xbox One wireless adapter behaves on Windows.
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

As explained in 1407814240-4275-1-git-send-email-decui@microsoft.com we
have a hard load dependency between i8042 and atkbd which prevents
keyboard from working on Gen2 Hyper-V VMs.

> hyperv_keyboard invokes serio_interrupt(), which needs a valid serio
> driver like atkbd.c.  atkbd.c depends on libps2.c because it invokes
> ps2_command().  libps2.c depends on i8042.c because it invokes
> i8042_check_port_owner().  As a result, hyperv_keyboard actually
> depends on i8042.c.
>
> For a Generation 2 Hyper-V VM (meaning no i8042 device emulated), if a
> Linux VM (like Arch Linux) happens to configure CONFIG_SERIO_I8042=m
> rather than =y, atkbd.ko can't load because i8042.ko can't load(due to
> no i8042 device emulated) and finally hyperv_keyboard can't work and
> the user can't input: https://bugs.archlinux.org/task/39820
> (Ubuntu/RHEL/SUSE aren't affected since they use CONFIG_SERIO_I8042=y)

To break the dependency we move away from using i8042_check_port_owner()
and instead allow serio port owner specify a mutex that clients should use
to serialize PS/2 command stream.
Reported-by: Mark Laws <mdl@60hz.org>
Tested-by: Mark Laws <mdl@60hz.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The of_node_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In cros_ec_keyb we stored "dev" in "struct cros_ec_keyb", but this was
the EC's dev pointer and not the keyboard's.  Let's clean this up to
make it the keyboard's dev pointer.  This could be useful in future
patches but also has the nice effect of changing a few printouts to
include the name of the keyboard device instead of the EC device, so we
will see:

[    1.224648] cros-ec-keyb ff110000.spi:ec@0:keyboard-controller: valid_keys[00] = 0x14

instead of:

[    1.224505] cros-ec-spi spi0.0: valid_keys[00] = 0x14
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Prepare first round of input updates for 4.8 merge window.

Use memdup_user to duplicate a memory region from user-space to
kernel-space, instead of open coding using kmalloc & copy_from_user.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Passes input_id struct to the common probe function for the tsc200x drivers
instead of just the bustype.

This allows for the use of the product variable to set the input_dev->name
variable according to the type of touchscreen used. Note that when we
introduced support for TSC2004 we started calling everything TSC200X, so
let's keep this quirk.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Cc: stable@vger.kernel.org
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The size of individual keymap in drivers/tty/vt/keyboard.c is NR_KEYS,
which is currently 256, whereas number of keys/buttons in input device (and
therefor in key_down) is much larger - KEY_CNT - 768, and that can cause
out-of-bound access when we do

	sym = U(key_maps[0][k]);

with large 'k'.

To fix it we should not attempt iterating beyond smaller of NR_KEYS and
KEY_CNT.

Also while at it let's switch to for_each_set_bit() instead of open-coding
it.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

According to the RMI4 spec the maximum size of F12 control register 8 is
15 bytes. The current code incorrectly reports an error if control 8 is
greater then 14. Making sensors with a control register 8 with 15 bytes
unusable.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reported-by: Chris Healy <cphealy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We should only "put" the interface if submitting URB or setting tablet mode
in pegasus_open() fails, otherwise leave it to pegasus_close().
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

input_mt_init_slots() may fail and we should be handling failures properly.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Sync up to bring in wacom_w8001 changes to avoid merge conflicts later.

Add support for axis inversion / swapping using the new
touchscreen_parse_properties() and touchscreen_set_mt_pos()
functionality.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use the touchscreen_parse_properties() and touchscreen_report_pos() to
perform coordinates transformation, instead of DIY code, which results in a
nice cleanup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add support for inverting / swapping axes using the new
touchscreen_parse_properties() and touchscreen_report_pos()
functionality.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Extend touchscreen_parse_properties() with support for the
touchscreen-inverted-x/y and touchscreen-swapped-x-y properties and
add touchscreen_set_mt_pos() and touchscreen_report_pos() helper
functions for storing coordinates into a input_mt_pos struct, or
directly reporting them, taking these properties into account.

This commit also modifies the existing callers of
touchscreen_parse_properties() to pass in NULL for the new third
argument, keeping the existing behavior.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The size of relative data in F11 is already defined by RMI_F11_REL_BYTES.
Use the define in rmi_f11_rel_pos_report() to be consistent.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Remove the data_base_addr_offset variable in rmi_f11_attention(). The
f11 data is read as a single block so there is no need to store an offset
to the data address.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The pointer to struct rmi_function in f12_data is never set and was never
used. The fn pointer is also stored in rmi_2d_sensor which is a member of
f12_data.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>