- 25 Mar, 2013 22 commits
-
-
Tomas Winkler authored
similar to read/write add also irq completion handler that is called for the irq thread rename missnamed mei_irq_complete_handler to mei_cl_complete_handler as it operates on a single client Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Lokesh Vutla authored
of_get_property returns value in Big Endian format. Before using this value it should be converted to little endian using be32_to_cpup(). Custom configs of emif are read from dt using of_get_property, but these are not converted to litte endian format. Correcting the same here. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Grygorii Strashko authored
ERRATA DESCRIPTION : The EMIF supports power-down state for low power. The EMIF automatically puts the SDRAM into power-down after the memory is not accessed for a defined number of cycles and the EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE bit field is set to 0x4. As the EMIF supports automatic output impedance calibration, a ZQ calibration long command is issued every time it exits active power-down and precharge power-down modes. The EMIF waits and blocks any other command during this calibration. The EMIF does not allow selective disabling of ZQ calibration upon exit of power-down mode. Due to very short periods of power-down cycles, ZQ calibration overhead creates bandwidth issues and increases overall system power consumption. On the other hand, issuing ZQ calibration long commands when exiting self-refresh is still required. WORKAROUND : Because there is no power consumption benefit of the power-down due to the calibration and there is a performance risk, the guideline is to not allow power-down state and, therefore, to not have set the EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE bit field to 0x4. This is applicable only for EMIF4D IP used in OMAP4 Soc's. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Vitaly Chernooky <vitaly.chernooky@ti.com> Signed-off-by: Oleksandr Dmytryshyn <oleksandr.dmytryshyn@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Oleksandr Dmytryshyn authored
The issue was that only the first timings table was added to the emif platform data at the emif driver registration. All other timings tables was filled with zeros. Now all emif timings table are added to the platform data. Signed-off-by: Oleksandr Dmytryshyn <oleksandr.dmytryshyn@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Nishanth Menon authored
Some machine or kernel variants might have missed implementation of power off handlers. We DONOT want to let the system be in "out of spec" state in this condition. So, WARN and attempt a machine restart in the hopes of clearing the out-of-spec temperature condition. NOTE: This is not the safest option, but safer than leaving the system in unstable conditions. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Nishanth Menon authored
As per JESD209-2E specification for LPDDR2, http://www.jedec.org/standards-documents/results/jesd209-2E Table 73, LPDDR2 memories come in two flavors - Standard and Extended. The Standard types can operate from -25C to +85C However, beyond that and upto +105C can only be supported by Extended types. Unfortunately, it seems there is no info in MR0(device info) or MR[1,2](device feature) for run time detection of this capability as far as seen on the spec. Hence, we provide a custom_config flag to be populated by platforms which have these "extended" type memories. For the "Standard" memories, we need to consider MR4 notifications of temperature triggers >85C as equivalent to thermal shutdown events (equivalent to Spec specified thermal shutdown events for "extended" parts). Reported-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Nishanth Menon authored
In case the custom timings provide values which overflow the maximum possible field value, warn and use maximum permissible value. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ambresh K authored
Program the power management shadow register on freq update Else the concept of threshold frequencies dont really matter as the system always uses the performance mode timing for LP which is programmed in at init time. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Ambresh K <ambresh@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Lokesh Vutla authored
The driver tries to round up the specified timeout cycles to the next power of 2 value. This should be done defore updating timeout variable. Correcting this here. Reported-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexandru Gheorghiu authored
Used PTR_RET function instead of IS_ERR and PTR_ERR. Patch found using coccinelle. Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Silviu-Mihai Popescu authored
This replaces calls to kmalloc followed by memcpy with a single call to kmemdup. This was found via make coccicheck. Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Fabio Porcedda authored
Use module_platform_driver_probe() macro which makes the code smaller and simpler. Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com> Cc: Matt Porter <mporter@ti.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
David Brown authored
The ssbi device is specific to the Qualcomm MSM SoCs. Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
David Brown authored
Although the SSBI sub is currently only used on MSM SoCs, it is still a bus in its own right. Remove this msm_ prefix from the driver and it's symbols. Clients can now refer directly to ssbi_write() and ssbi_read(). Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
David Brown authored
Remove some unhelpful error logs. This also removes the necessity of having a pointer back to the struct device within the ssbi-specific structure Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
David Brown authored
With device tree, and deferred probe, it is no longer necessary to make sure that the ssbi bus driver is initialized very early. Restore to a regular module_init(). Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
David Brown authored
The ssbi driver uses a busywait loop to read its status register. Add a comment explaining the timing of the device itself so that future developers can better understand this delay, and possibly diagnose any problems. Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
David Brown authored
The SSBI bus is exclusive to the Qualcomm MSM targets, and all SoCs using it will be using device tree. Convert this driver to indentify with device tree. This makes the bus probing a good bit simpler, since the attaching of child nodes can be represented directly in the devicetree, rather than having to be inferred by name. Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
David Brown authored
The ssbi driver's read/write entry points are protected with wrappers in the case when the driver isn't enabled. These wrappers don't make any sense, since a client of the SSBI bus won't work without it. Make these just regular functions, so that the SSBI driver can be built as a module. Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
David Brown authored
msm_ssbi_remove is referenced with __exit_p, but not declared with __exit. This causes a warning when the driver is not built as a module: drivers/ssbi/ssbi.c:341:23: warning: 'msm_ssbi_remove' defined but not used [-Wunused-function] The remove is needed for unbinding to work, even if not compiled as a module, so just remove it. Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
David Brown authored
Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Kenneth Heitke authored
SSBI is the Qualcomm single-wire serial bus interface used to connect the MSM devices to the PMIC and other devices. Since SSBI only supports a single slave, the driver gets the name of the slave device passed in from the board file through the master device's platform data. SSBI registers pretty early (postcore), so that the PMIC can come up before the board init. This is useful if the board init requires the use of gpios that are connected through the PMIC. Based on a patch by Dima Zavin <dima@android.com> that can be found at: http://android.git.kernel.org/?p=kernel/msm.git;a=commitdiff;h=eb060bac4 This patch adds PMIC Arbiter support for the MSM8660. The PMIC Arbiter is a hardware wrapper around the SSBI 2.0 controller that is designed to overcome concurrency issues and security limitations. A controller_type field is added to the platform data to specify the type of the SSBI controller (1.0, 2.0, or PMIC Arbiter). [davidb@codeaurora.org: I've moved this driver into drivers/ssbi/ and added an include for linux/module.h so that it will compile] Signed-off-by: Kenneth Heitke <kheitke@codeaurora.org> Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 19 Mar, 2013 1 commit
-
-
Kurt Van Dijck authored
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 15 Mar, 2013 17 commits
-
-
Kurt Van Dijck authored
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Kurt Van Dijck authored
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
H Hartley Sweeten authored
Use the new module_pcmcia_driver() macro to remove the boilerplate module init/exit code in the pcmcia drivers. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
H Hartley Sweeten authored
Use the new module_pcmcia_driver() macro to remove the boilerplate module init/exit code in the pcmcia drivers. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
H Hartley Sweeten authored
Use the new module_pcmcia_driver() macro to remove the boilerplate module init/exit code in the pcmcia drivers. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
H Hartley Sweeten authored
Use the new module_pcmcia_driver() macro to remove the boilerplate module init/exit code in the pcmcia drivers. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
H Hartley Sweeten authored
Use the new module_pcmcia_driver() macro to remove the boilerplate module init/exit code in the pcmcia drivers. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
H Hartley Sweeten authored
Use the new module_pcmcia_driver() macro to remove the boilerplate module init/exit code in the pcmcia drivers. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
H Hartley Sweeten authored
Use the new module_pcmcia_driver() macro to remove the boilerplate module init/exit code in the pcmcia drivers. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
H Hartley Sweeten authored
Use the new module_pcmcia_driver() macro to remove the boilerplate module init/exit code in the pcmcia drivers. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
H Hartley Sweeten authored
Use the new module_pcmcia_driver() macro to remove the boilerplate module init/exit code in the pcmcia drivers. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
H Hartley Sweeten authored
Use the new module_pcmcia_driver() macro to remove the boilerplate module init/exit code in the pcmcia drivers. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
H Hartley Sweeten authored
Introduce the module_pcmcia_driver() macro which is a convenience macro for pcmcia driver modules. It is intended to be used by pcmcia drivers with init/exit sections that do nothing but register/unregister the pcmcia driver. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: linux-pcmcia@lists.infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Fabio Porcedda authored
This patch converts the drivers to use the module_platform_driver_probe() macro which makes the code smaller and a bit simpler. Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com> Cc: Matt Mackall <mpm@selenic.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dan Carpenter authored
We're iterating through abps[] printing information, but here we use the wrong array index. IndexCard comes from the user and in this case it was specifically not range checked because we didn't expect to use it. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Samuel Iglesias Gonsalvez authored
One function is ipack_device_init(). If it fails, the caller should execute ipack_put_device(). The second function is ipack_device_add that only adds the device. If it fails, the caller should execute ipack_put_device(). Then the device is removed with refcount = 0, as device_register() kernel documentation says. ipack_device_del() is added to remove the device. Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Samuel Iglesias Gonsalvez authored
Prepare everything for later use. Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-