As this define check if huge, this makes easier to read the code.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Semantics of NR_IRQS is different on machines with SPARSE_IRQ option
disabled or enabled, in the latter case IRQs are allocated starting
at least from the value specified by NR_IRQS and going upwards, so
the check of (irq >= NR_IRQ) to decide about an error code returned by
platform_get_irq() is completely invalid, don't attempt to overrule
irq subsystem in the driver.

The change fixes lpc32xx_keys driver initialization on boot:

  lpc32xx_keys 40050000.key: failed to get platform irq
  lpc32xx_keys: probe of 40050000.key failed with error -22
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The code uses of_property_read_u32 and expects positive values.  However,
the values are stored in signed int variables.  Additionally, the registers
values are also stored in signed variables without a good reason
(readl/writel expect u32).

The only time this caused a real bug was in the new average-samples
property, in which the property is numerically compared and implicitly
expected to be positive.

I believe it's better to change all the properties and registers to u32,
for consistency and warnings reduction.
Signed-off-by: Guy Shapiro <guy.shapiro@mobi-wize.com>
Reported-by: Bjørn Forsman <bjorn.forsman@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add mask of each function bits of REG_ADC_CFG, and clear these
function bits first, otherwise use '|=' operation may get the
wrong setting which depends on the original value of REG_ADC_CFG.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Guy Shapiro <guy.shapiro@mobi-wize.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Using regmap_update_bits(..., mask, 1) with 'mask' following (1 << k)
and k greater than 0 is wrong. Indeed, _regmap_update_bits will perform
(mask & 1), which results in 0 if LSB of mask is 0. Thus the call
regmap_update_bits(..., mask, 1) is in reality equivalent to
regmap_update_bits(..., mask, 0).

In such a case, the correct use is regmap_update_bits(..., mask, mask).

This driver is performing such a mistake with the DRV2667_STANDBY mask,
which equals (1 << 6). Fix the driver to make it consistent with the
API, and fix the alignment problem at the same time. Please note that
this change is untested, as I do not have this piece of hardware.
Testers are welcome!
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Using regmap_update_bits(..., mask, 1) with 'mask' following (1 << k)
and k greater than 0 is wrong. Indeed, _regmap_update_bits will perform
(mask & 1), which results in 0 if LSB of mask is 0. Thus the call
regmap_update_bits(..., mask, 1) is in reality equivalent to
regmap_update_bits(..., mask, 0).

In such a case, the correct use is regmap_update_bits(..., mask, mask).

This driver is performing such a mistake with the DRV2665_STANDBY mask,
which equals BIT(6). Fix the driver to make it consistent with the API,
and fix the alignment problem at the same time. Please note that this
change is untested, as I do not have this piece of hardware. Testers
are welcome!
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The return value of alps_get_pkt_id_ss4_v2() should really be "enum
SS4_PACKET_ID", not "unsigned char".  Correct this.

Also, most of the Alps SS5 (SS4 v2) packet byte parsing code is implemented
using macros, but there are a few places where bytes are directly
manipulated in alps.c.  For consistency, migrate the rest of these to
macros.
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Paul Donohue <linux-kernel@PaulSD.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

For consistency and clarity, the input_report_*() functions should be
called by alps_process_packet_ss4_v2() instead of by alps_decode_ss4_v2().
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Paul Donohue <linux-kernel@PaulSD.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The current Alps SS5 (SS4 v2) code generates bogus TouchPad events when
TrackStick packets are processed.

This causes the xorg synaptics driver to print
"unable to find touch point 0" and
"BUG: triggered 'if (priv->num_active_touches > priv->num_slots)'"
messages.  It also causes unexpected TouchPad button release and re-click
event sequences if the TrackStick is moved while holding a TouchPad
button.

This commit corrects the problem by adjusting alps_process_packet_ss4_v2()
so that it only sends TrackStick reports when processing TrackStick
packets.
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Paul Donohue <linux-kernel@PaulSD.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The i.MX6UL internal touchscreen controller contains an option to
average upon samples. This feature reduces noise from the produced
touch locations.

This patch adds sample averaging support to the imx6ul_tsc device
driver.
Signed-off-by: Guy Shapiro <guy.shapiro@mobi-wize.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Unlike previous Xbox pads, the Xbox One pad doesn't have "sticky" rumble
packets. The duration is encoded into the command and expiration is handled
by the pad firmware.

ff-memless needs pseudo-sticky behavior for rumble effects to behave
properly for long duration effects. We already specify the maximum rumble
on duration in the command packets, but it's still only good for about 2.5
seconds of rumble. This is easily reproducible running fftest's sine
vibration test.

It turns out there's a repeat count encoded in the rumble command. We can
abuse that to get the pseudo-sticky behavior needed for rumble to behave as
expected for effects with long duration.

By my math, this change should allow a single ff_effect to rumble for 10
minutes straight, which should be more than enough for most needs.
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This is the new gamepad that ships with the Xbox One S which
includes Bluetooth functionality.
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The PNP0C40 device of the Surface 3 doesn't have any GPIO attached to it.
Instead of trying to access the GPIO, request the count beforehand and
bail out if it is null or if an error is returned.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

gpio_keys will later use gpio_is_valid(). To match the actual
behavior, we should use it here too.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Commit 700a38b2 ("Input: gpio_keys - switch to using generic device
properties") switched to use generic device properties for GPIO keys and
commit 5feeca3c ("Input: gpio_keys - add support for GPIO descriptors")
switched from legacy GPIO numbers to GPIO descriptors.

Previously devm_gpio_request_one was explicitly passed GPIOF_DIR_IN flag
to set the GPIO direction as input. However devm_get_gpiod_from_child
doesn't have such provisions and hence fwnode_get_named_gpiod can't set
it as input.

This breaks few platforms with the following error:
" gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
  unable to lock HW IRQ <n> for IRQ
  genirq: Failed to request resources for POWER (irq <x>) on irqchip
  gpio_keys: Unable to claim irq <x>; error -22
  gpio-keys: probe failed with error -22 "

This patch fixes the issue by setting input direction explicitly for
gpio lines described by generic properties.

Fixes: 700a38b2 ("Input: gpio_keys - switch to using generic device properties")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Trivial fix to spelling mistake "failied" to "failed" in
dev_err message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

On some tablets the touchscreen controller is powered by separate
regulators, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

commit ef3714fd ("Input: bma150 - extend chip detection for bma180"),
adds bma180 chip-ids to the input bma150 driver, assuming that they are
100% compatible, but the bma180 is not compatible with the bma150 at all,
it has 14 bits resolution instead of 10, and it has quite different
control registers too.

Treating the bma180 as a bma150 wrt its data registers will just result
in throwing away the lowest 4 bits, which is not too bad. But the ctrl
registers are a different story. Things happen to just work but supporting
that certainly does not make treating the bma180 the same as the bma150
right.

Since some setups depend on the evdev interface the bma150 driver offers
on top of the bma180, we cannot simply remove the bma180 ids.

So this commit only removes the bma180 id when the bma180 iio driver,
which does treat the bma180 properly, is enabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add binding information for DA9061 onkey.

This patch updates the compatible string "dlg,da9061-onkey" to support
DA9061, removes the reference to KEY_SLEEP (which the driver no longer
supports) and fixes a typo in the example for DA9063.

Supporting KEY_SLEEP was not the general convention and the typical
solution should have been for KEY_POWER to support both cases of suspend
and S/W power off. This change was sent to the DA9063 ONKEY device
driver in a separate patch, but the documentation was not updated at
that time.
- f889beaa Report KEY_POWER instead of KEY_SLEEP during power key-press

This patch also adds two new examples, one for DA9062 and one for DA9061.
The DA9061 examples uses a fall-back compatible string for the DA9062
onkey driver.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add reporting product ID through input_id.
Signed-off-by: Sangwon Jee <jeesw@melfas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Make use of the device property API in this driver so that both OF based
systems and ACPI based systems can use this driver.
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

GPIO descriptors are the preferred way over legacy GPIO numbers
nowadays. Convert the driver to use GPIO descriptors internally but
still allow passing legacy GPIO numbers from platform data to support
existing platforms.

Based on commits 633a21d8 ("input: gpio_keys_polled: Add support
for GPIO descriptors") and 1ae5ddb6 ("Input: gpio_keys_polled -
request GPIO pin as input.").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

for_each_available_child_of_node(node, pp) takes reference to 'pp' and
drops it when attempting next iteration. However if we exit the loop early
we need to drop the reference ourselves.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of using #ifdef, let's mark suspend and resume methods as
__maybe_unused to provide better compile coverage.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

It does not matter if given GPIO may sleep or not when reading state,
polling is always done in a non-atomic context, so we should always
be able to simply use gpiod_get_value_cansleep().

Also let's note in the logs when we fail to read gpio state.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Commit 633a21d8 ("input: gpio_keys_polled: Add support for GPIO
descriptors") placed gpio descriptor into gpio_keys_button structure, which
is supposed to be part of platform data and not modifiable by the driver.
To keep the data constant, let's move the descriptor to
gpio_keys_button_data structure instead.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Before this patch:

$ modinfo drivers/input/misc/da9063_onkey.ko | grep alias
alias:          platform:da9063-onkey

After this patch:

$ modinfo drivers/input/misc/da9063_onkey.ko | grep alias
alias:          platform:da9063-onkey
alias:          of:N*T*Cdlg,da9062-onkeyC*
alias:          of:N*T*Cdlg,da9062-onkey
alias:          of:N*T*Cdlg,da9063-onkeyC*
alias:          of:N*T*Cdlg,da9063-onkey
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Before this patch:

$ modinfo drivers/input/touchscreen/fsl-imx25-tcq.ko | grep alias

After this patch:

$ modinfo drivers/input/touchscreen/fsl-imx25-tcq.ko | grep alias
alias:          of:N*T*Cfsl,imx25-tcqC*
alias:          of:N*T*Cfsl,imx25-tcq
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

it's always easier to retrieve these information in bug reports when
it is always printed in the dmesg.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Older versions of gcc warn about the tca8418_irq_handler function
as they can't keep track of the variable assignment inside of the
loop when using the -Wmaybe-unintialized flag:

drivers/input/keyboard/tca8418_keypad.c: In function ‘tca8418_irq_handler’:
drivers/input/keyboard/tca8418_keypad.c:172:9: error: ‘reg’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/input/keyboard/tca8418_keypad.c:165:5: note: ‘reg’ was declared here

This is fixed in gcc-6, but it's possible to rearrange the code
in a way that avoids the warning on older compilers as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use product id for firmware name to request compatible firmware.
Signed-off-by: Sangwon Jee <jeesw@melfas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Copyright header is updated to add DA9061 in its description and the module
description macro is extended to include DA9061.

Minor change to the code, alters dev_dbg() statements to report a generic
"PMIC" instead of DA9063. This device driver is compatible with DA9061,
DA9062 and DA9063.

Kconfig is updated to reflect support for DA9061/62/63.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Trivial fix to typo in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of relying on this model zoo let's skip selftest on all newer Asus
laptops (newer as in when they changed "Computer" -> "COMPUTER" in their
DMI data).
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add product_id sysfs attribute and update protocol version to support it.
Signed-off-by: Sangwon Jee <jeesw@melfas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Sync up with mainline to bring in I2C host notify changes and other
updates.

On suspend/resume cycle, selftest is executed to reset i8042 controller.
But when this is done in Asus devices, subsequent calls to detect/init
functions to elantech driver fails. Skipping selftest fixes this problem.

An easier step to reproduce this problem is adding i8042.reset=1 as a
kernel parameter. On Asus laptops, it'll make the system to start with the
touchpad already stuck, since psmouse_probe forcibly calls the selftest
function.

This patch was inspired by John Hiesey's change[1], but, since this problem
affects a lot of models of Asus, let's avoid running selftests on them.

All models affected by this problem:
A455LD
K401LB
K501LB
K501LX
R409L
V502LX
X302LA
X450LCP
X450LD
X455LAB
X455LDB
X455LF
Z450LA

[1]: https://marc.info/?l=linux-input&m=144312209020616&w=2

Fixes: "ETPS/2 Elantech Touchpad dies after resume from suspend"
(https://bugzilla.kernel.org/show_bug.cgi?id=107971)
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add ic_name sysfs attribute for retrieving IC model name.
Signed-off-by: Sangwon Jee <jeesw@melfas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add maintainer information.
Signed-off-by: Sangwon Jee <jeesw@melfas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>