SOCK_TSTAMP_NEW (timespec64 instead of timespec) is also used for
hardware time stamps (configured via SO_TIMESTAMPING_NEW).

User space (ptp4l) first configures hardware time stamping via
SO_TIMESTAMPING_NEW which sets SOCK_TSTAMP_NEW. In the next step, ptp4l
disables SO_TIMESTAMPNS(_NEW) (software time stamps), but this must not
switch hardware time stamps back to "32 bit mode".

This problem happens on 32 bit platforms were the libc has already
switched to struct timespec64 (from SO_TIMExxx_OLD to SO_TIMExxx_NEW
socket options). ptp4l complains with "missing timestamp on transmitted
peer delay request" because the wrong format is received (and
discarded).

Fixes: 887feae3 ("socket: Add SO_TIMESTAMP[NS]_NEW")
Fixes: 783da70e ("net: add sock_enable_timestamps")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The comparison of optname with SO_TIMESTAMPING_NEW is wrong way around,
so SOCK_TSTAMP_NEW will first be set and than reset again. Additionally
move it out of the test for SOF_TIMESTAMPING_RX_SOFTWARE as this seems
unrelated.

This problem happens on 32 bit platforms were the libc has already
switched to struct timespec64 (from SO_TIMExxx_OLD to SO_TIMExxx_NEW
socket options). ptp4l complains with "missing timestamp on transmitted
peer delay request" because the wrong format is received (and
discarded).

Fixes: 9718475e ("socket: Add SO_TIMESTAMPING_NEW")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Reviewed-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

With the introduction of netif_set_xps_queue, XPS can be enabled
by the driver at initialization.

Update the documentation to reflect this, as otherwise users
may incorrectly believe that the feature is off by default.

Fixes: 537c00de ("net: Add functions netif_reset_xps_queue and netif_set_xps_queue")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The phy_reset_after_clk_enable() is always called with ndev->phydev,
however that pointer may be NULL even though the PHY device instance
already exists and is sufficient to perform the PHY reset.

This condition happens in fec_open(), where the clock must be enabled
first, then the PHY must be reset, and then the PHY IDs can be read
out of the PHY.

If the PHY still is not bound to the MAC, but there is OF PHY node
and a matching PHY device instance already, use the OF PHY node to
obtain the PHY device instance, and then use that PHY device instance
when triggering the PHY reset.

Fixes: 1b0a83ac ("net: fec: add phy_reset_after_clk_enable() support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Richard Leitner <richard.leitner@skidata.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

netcons calls napi_poll with a budget of 0 to transmit packets.
Handle this by:
 - skipping RX processing
 - do not try to recycle TX packets to the RX cache
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

kmalloc returns KSEG0 addresses so convert back from KSEG1
in kfree. Also make sure array is freed when the driver is
unloaded from the kernel.

Fixes: ef11291b ("Add support the Korina (IDT RC32434) Ethernet MAC")
Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Between queuing the delayed work and finishing the setup of the dsa
ports, the process may sleep in request_module() (via
phy_device_create()) and the queued work may be executed prior to the
switch net devices being registered. In ksz_mib_read_work(), a NULL
dereference will happen within netof_carrier_ok(dp->slave).

Not queuing the delayed work in ksz_init_mib_timer() makes things even
worse because the work will now be queued for immediate execution
(instead of 2000 ms) in ksz_mac_link_down() via
dsa_port_link_register_of().

Call tree:
ksz9477_i2c_probe()
\--ksz9477_switch_register()
   \--ksz_switch_register()
      +--dsa_register_switch()
      |  \--dsa_switch_probe()
      |     \--dsa_tree_setup()
      |        \--dsa_tree_setup_switches()
      |           +--dsa_switch_setup()
      |           |  +--ksz9477_setup()
      |           |  |  \--ksz_init_mib_timer()
      |           |  |     |--/* Start the timer 2 seconds later. */
      |           |  |     \--schedule_delayed_work(&dev->mib_read, msecs_to_jiffies(2000));
      |           |  \--__mdiobus_register()
      |           |     \--mdiobus_scan()
      |           |        \--get_phy_device()
      |           |           +--get_phy_id()
      |           |           \--phy_device_create()
      |           |              |--/* sleeping, ksz_mib_read_work() can be called meanwhile */
      |           |              \--request_module()
      |           |
      |           \--dsa_port_setup()
      |              +--/* Called for non-CPU ports */
      |              +--dsa_slave_create()
      |              |  +--/* Too late, ksz_mib_read_work() may be called beforehand */
      |              |  \--port->slave = ...
      |             ...
      |              +--Called for CPU port */
      |              \--dsa_port_link_register_of()
      |                 \--ksz_mac_link_down()
      |                    +--/* mib_read must be initialized here */
      |                    +--/* work is already scheduled, so it will be executed after 2000 ms */
      |                    \--schedule_delayed_work(&dev->mib_read, 0);
      \-- /* here port->slave is setup properly, scheduling the delayed work should be safe */

Solution:
1. Do not queue (only initialize) delayed work in ksz_init_mib_timer().
2. Only queue delayed work in ksz_mac_link_down() if init is completed.
3. Queue work once in ksz_switch_register(), after dsa_register_switch()
has completed.

Fixes: 7c6ff470 ("net: dsa: microchip: add MIB counter reading support")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Tobias reported regressions in IPsec tests following the patch
referenced by the Fixes tag below. The root cause is dropping the
reset of the flowi4_oif after the fib_lookup. Apparently it is
needed for xfrm cases, so restore the oif update to ip_route_output_flow
right before the call to xfrm_lookup_route.

Fixes: 2fbc6e89 ("ipv4: Update exception handling for multipath routes via same device")
Reported-by: Tobias Brunner <tobias@strongswan.org>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Paolo Abeni says:

====================
mptcp: some fallback fixes

pktdrill pointed-out we currently don't handle properly some
fallback scenario for MP_JOIN subflows

The first patch addresses such issue.

Patch 2/2 fixes a related pre-existing issue that is more
evident after 1/2: we could keep using for MPTCP signaling
closed subflows.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The msk can close MP_JOIN subflows if the initial handshake
fails. Currently such subflows are kept alive in the
conn_list until the msk itself is closed.

Beyond the wasted memory, we could end-up sending the
DATA_FIN and the DATA_FIN ack on such socket, even after a
reset.

Fixes: 43b54c6e ("mptcp: Use full MPTCP-level disconnect state machine")
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Additional/MP_JOIN subflows that do not pass some initial handshake
tests currently causes fallback to TCP. That is an RFC violation:
we should instead reset the subflow and leave the the msk untouched.

Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/91
Fixes: f296234c ("mptcp: Add handling of incoming MP_JOIN requests")
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

For older versions of gcc, the array = {0}; will cause warnings:

net/smc/smc_llc.c: In function 'smc_llc_add_link_local':
net/smc/smc_llc.c:1212:9: warning: missing braces around initializer [-Wmissing-braces]
  struct smc_llc_msg_add_link add_llc = {0};
         ^
net/smc/smc_llc.c:1212:9: warning: (near initialization for 'add_llc.hd') [-Wmissing-braces]
net/smc/smc_llc.c: In function 'smc_llc_srv_delete_link_local':
net/smc/smc_llc.c:1245:9: warning: missing braces around initializer [-Wmissing-braces]
  struct smc_llc_msg_del_link del_llc = {0};
         ^
net/smc/smc_llc.c:1245:9: warning: (near initialization for 'del_llc.hd') [-Wmissing-braces]

2 warnings generated

Fixes: 4dadd151 ("net/smc: enqueue local LLC messages")
Signed-off-by: Pujin Shi <shipujin.t@gmail.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

For older versions of gcc, the array = {0}; will cause warnings:

net/smc/smc_llc.c: In function 'smc_llc_send_link_delete_all':
net/smc/smc_llc.c:1317:9: warning: missing braces around initializer [-Wmissing-braces]
  struct smc_llc_msg_del_link delllc = {0};
         ^
net/smc/smc_llc.c:1317:9: warning: (near initialization for 'delllc.hd') [-Wmissing-braces]

1 warnings generated

Fixes: f3811fd7 ("net/smc: send DELETE_LINK, ALL message and wait for send to complete")
Signed-off-by: Pujin Shi <shipujin.t@gmail.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'linux-can-fixes-for-5.9-20201008' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

====================
linux-can-fixes-for-5.9-20201008

The first patch is by Lucas Stach and fixes m_can driver by removing an
erroneous call to m_can_class_suspend() in runtime suspend. Which causes the
pinctrl state to get stuck on the "sleep" state, which breaks all CAN
functionality on SoCs where this state is defined.

The last two patches target the j1939 protocol: Cong Wang fixes a syzbot
finding of an uninitialized variable in the j1939 transport protocol. I
contribute a patch, that fixes the initialization of a same uninitialized
variable in a different function.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In the function node_lost_contact(), we call __skb_queue_purge() without
grabbing the list->lock. This can cause to a race-condition why processing
the list 'namedq' in calling path tipc_named_rcv()->tipc_named_dequeue().

    [] BUG: kernel NULL pointer dereference, address: 0000000000000000
    [] #PF: supervisor read access in kernel mode
    [] #PF: error_code(0x0000) - not-present page
    [] PGD 7ca63067 P4D 7ca63067 PUD 6c553067 PMD 0
    [] Oops: 0000 [#1] SMP NOPTI
    [] CPU: 1 PID: 15 Comm: ksoftirqd/1 Tainted: G  O  5.9.0-rc6+ #2
    [] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS [...]
    [] RIP: 0010:tipc_named_rcv+0x103/0x320 [tipc]
    [] Code: 41 89 44 24 10 49 8b 16 49 8b 46 08 49 c7 06 00 00 00 [...]
    [] RSP: 0018:ffffc900000a7c58 EFLAGS: 00000282
    [] RAX: 00000000000012ec RBX: 0000000000000000 RCX: ffff88807bde1270
    [] RDX: 0000000000002c7c RSI: 0000000000002c7c RDI: ffff88807b38f1a8
    [] RBP: ffff88807b006288 R08: ffff88806a367800 R09: ffff88806a367900
    [] R10: ffff88806a367a00 R11: ffff88806a367b00 R12: ffff88807b006258
    [] R13: ffff88807b00628a R14: ffff888069334d00 R15: ffff88806a434600
    [] FS:  0000000000000000(0000) GS:ffff888079480000(0000) knlGS:0[...]
    [] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
    [] CR2: 0000000000000000 CR3: 0000000077320000 CR4: 00000000000006e0
    [] Call Trace:
    []  ? tipc_bcast_rcv+0x9a/0x1a0 [tipc]
    []  tipc_rcv+0x40d/0x670 [tipc]
    []  ? _raw_spin_unlock+0xa/0x20
    []  tipc_l2_rcv_msg+0x55/0x80 [tipc]
    []  __netif_receive_skb_one_core+0x8c/0xa0
    []  process_backlog+0x98/0x140
    []  net_rx_action+0x13a/0x420
    []  __do_softirq+0xdb/0x316
    []  ? smpboot_thread_fn+0x2f/0x1e0
    []  ? smpboot_thread_fn+0x74/0x1e0
    []  ? smpboot_thread_fn+0x14e/0x1e0
    []  run_ksoftirqd+0x1a/0x40
    []  smpboot_thread_fn+0x149/0x1e0
    []  ? sort_range+0x20/0x20
    []  kthread+0x131/0x150
    []  ? kthread_unuse_mm+0xa0/0xa0
    []  ret_from_fork+0x22/0x30
    [] Modules linked in: veth tipc(O) ip6_udp_tunnel udp_tunnel [...]
    [] CR2: 0000000000000000
    [] ---[ end trace 65c276a8e2e2f310 ]---

To fix this, we need to grab the lock of the 'namedq' list on both
path calling.

Fixes: cad2929d ("tipc: update a binding service via broadcast")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Huu Le <hoang.h.le@dektech.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

skb_unshare() drops a reference count on the old skb unconditionally,
so in the failure case, we end up freeing the skb twice here.
And because the skb is allocated in fclone and cloned by caller
tipc_msg_reassemble(), the consequence is actually freeing the
original skb too, thus triggered the UAF by syzbot.

Fix this by replacing this skb_unshare() with skb_cloned()+skb_copy().

Fixes: ff48b622 ("tipc: use skb_unshare() instead in tipc_buf_append()")
Reported-and-tested-by: syzbot+e96a7ba46281824cc46a@syzkaller.appspotmail.com
Cc: Jon Maloy <jmaloy@redhat.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Remove one of the two instances of the function prototype for
tls_validate_xmit_skb().
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Boris Pismenny <borisp@nvidia.com>
Cc: Aviad Yehezkel <aviadye@nvidia.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

At first when sendpage gets called, if there is more data, 'more' in
tls_push_data() gets set which later sets pending_open_record_frags, but
when there is no more data in file left, and last time tls_push_data()
gets called, pending_open_record_frags doesn't get reset. And later when
2 bytes of encrypted alert comes as sendmsg, it first checks for
pending_open_record_frags, and since this is set, it creates a record with
0 data bytes to encrypt, meaning record length is prepend_size + tag_size
only, which causes problem.
 We should set/reset pending_open_record_frags based on more bit.

Fixes: e8f69799 ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fix comment typo.
s/abitrary/arbitrary/
Signed-off-by: Naoki Hayama <naoki.hayama@lineo.co.jp>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When a ICMPV6_PKT_TOOBIG report a next-hop MTU that is less than the IPv6
minimum link MTU, the estimated path MTU is reduced to the minimum link
MTU. This behaviour breaks TAHI IPv6 Core Conformance Test v6LC4.1.6:
Packet Too Big Less than IPv6 MTU.

Referring to RFC 8201 section 4: "If a node receives a Packet Too Big
message reporting a next-hop MTU that is less than the IPv6 minimum link
MTU, it must discard it. A node must not reduce its estimate of the Path
MTU below the IPv6 minimum link MTU on receipt of a Packet Too Big
message."

Drop the path MTU update if reported MTU is less than the minimum link MTU.
Signed-off-by: Georg Kohmann <geokohma@cisco.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When processing a system suspend request we suspend modem endpoints
if they are enabled, and call ipa_cmd_tag_process() (which issues
IPA commands) to ensure the IPA pipeline is cleared.  It is an error
to attempt to issue an IPA command before setup is complete, so this
is clearly a bug.  But we also shouldn't suspend or resume any
endpoints that have not been set up.

Have ipa_endpoint_suspend() and ipa_endpoint_resume() immediately
return if setup hasn't completed, to avoid any attempt to configure
endpoints or issue IPA commands in that case.

Fixes: 84f9bd12 ("soc: qcom: ipa: IPA endpoints")
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter selftests fixes from
Fabian Frederick:

1) Extend selftest nft_meta.sh to check for meta cpu.

2) Fix selftest nft_meta.sh error reporting.

3) Fix shellcheck warnings in selftest nft_meta.sh.

4) Extend selftest nft_meta.sh to check for meta time.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

using packetdrill it's possible to observe the same MPTCP DSN being acked
by different subflows with DACK4 and DACK8. This is in contrast with what
specified in RFC8684 §3.3.2: if an MPTCP endpoint transmits a 64-bit wide
DSN, it MUST be acknowledged with a 64-bit wide DACK. Fix 'use_64bit_ack'
variable to make it a property of MPTCP sockets, not TCP subflows.

Fixes: a0c1d0ea ("mptcp: Use 32-bit DATA_ACK when possible")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The phy_reset_after_clk_enable() does a PHY reset, which means the PHY
loses its register settings. The fec_enet_mii_probe() starts the PHY
and does the necessary calls to configure the PHY via PHY framework,
and loads the correct register settings into the PHY. Therefore,
fec_enet_mii_probe() should be called only after the PHY has been
reset, not before as it is now.

Fixes: 1b0a83ac ("net: fec: add phy_reset_after_clk_enable() support")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch add the initialization of skbcnt, similar to:

    e009f95b can: j1935: j1939_tp_tx_dat_new(): fix missing initialization of skbcnt

Let's play save and initialize this skbcnt as well.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Pull vhost fixes from Michael Tsirkin:
 "Some last minute vhost,vdpa fixes.

  The last two of them haven't been in next but they do seem kind of
  obvious, very small and safe, fix bugs reported in the field, and they
  are both in a new mlx5 vdpa driver, so it's not like we can introduce
  regressions"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  vdpa/mlx5: Fix dependency on MLX5_CORE
  vdpa/mlx5: should keep avail_index despite device status
  vhost-vdpa: fix page pinning leakage in error path
  vhost-vdpa: fix vhost_vdpa_map() on error condition
  vhost: Don't call log_access_ok() when using IOTLB
  vhost: Use vhost_get_used_size() in vhost_vring_set_addr()
  vhost: Don't call access_ok() when using IOTLB
  vhost vdpa: fix vhost_vdpa_open error handling

This fixes an uninit-value warning:
BUG: KMSAN: uninit-value in can_receive+0x26b/0x630 net/can/af_can.c:650

Reported-and-tested-by: syzbot+3f3837e61a48d32b495f@syzkaller.appspotmail.com
Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol")
Cc: Robin van der Gracht <robin@protonic.nl>
Cc: Oleksij Rempel <linux@rempel-privat.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Link: https://lore.kernel.org/r/20201008061821.24663-1-xiyou.wangcong@gmail.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Pull networking fixes from Jakub Kicinski:
 "One more set of fixes from the networking tree:

   - add missing input validation in nl80211_del_key(), preventing
     out-of-bounds access

   - last minute fix / improvement of a MRP netlink (uAPI) interface
     introduced in 5.9 (current) release

   - fix "unresolved symbol" build error under CONFIG_NET w/o
     CONFIG_INET due to missing tcp_timewait_sock and inet_timewait_sock
     BTF.

   - fix 32 bit sub-register bounds tracking in the bpf verifier for OR
     case

   - tcp: fix receive window update in tcp_add_backlog()

   - openvswitch: handle DNAT tuple collision in conntrack-related code

   - r8169: wait for potential PHY reset to finish after applying a FW
     file, avoiding unexpected PHY behaviour and failures later on

   - mscc: fix tail dropping watermarks for Ocelot switches

   - avoid use-after-free in macsec code after a call to the GRO layer

   - avoid use-after-free in sctp error paths

   - add a device id for Cellient MPL200 WWAN card

   - rxrpc fixes:
      - fix the xdr encoding of the contents read from an rxrpc key
      - fix a BUG() for a unsupported encoding type.
      - fix missing _bh lock annotations.
      - fix acceptance handling for an incoming call where the incoming
        call is encrypted.
      - the server token keyring isn't network namespaced - it belongs
        to the server, so there's no need. Namespacing it means that
        request_key() fails to find it.
      - fix a leak of the server keyring"

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (21 commits)
  net: usb: qmi_wwan: add Cellient MPL200 card
  macsec: avoid use-after-free in macsec_handle_frame()
  r8169: consider that PHY reset may still be in progress after applying firmware
  openvswitch: handle DNAT tuple collision
  sctp: fix sctp_auth_init_hmacs() error path
  bridge: Netlink interface fix.
  net: wireless: nl80211: fix out-of-bounds access in nl80211_del_key()
  bpf: Fix scalar32_min_max_or bounds tracking
  tcp: fix receive window update in tcp_add_backlog()
  net: usb: rtl8150: set random MAC address when set_ethernet_addr() fails
  mptcp: more DATA FIN fixes
  net: mscc: ocelot: warn when encoding an out-of-bounds watermark value
  net: mscc: ocelot: divide watermark value by 60 when writing to SYS_ATOP
  net: qrtr: ns: Fix the incorrect usage of rcu_read_lock()
  rxrpc: Fix server keyring leak
  rxrpc: The server keyring isn't network-namespaced
  rxrpc: Fix accept on a connection that need securing
  rxrpc: Fix some missing _bh annotations on locking conn->state_lock
  rxrpc: Downgrade the BUG() for unsupported token type in rxrpc_read()
  rxrpc: Fix rxkad token xdr encoding
  ...

Remove propmt for selecting MLX5_VDPA by the user and modify
MLX5_VDPA_NET to select MLX5_VDPA. Also modify MLX5_VDPA_NET to depend
on mlx5_core.

This fixes an issue where configuration sets 'y' for MLX5_VDPA_NET while
MLX5_CORE is compiled as a module causing link errors.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 1a86b377 ("vdpa/mlx5: Add VDPA driver for supported mlx5 device")s
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20201007064011.GA50074@mtl-vdi-166.wap.labs.mlnxSigned-off-by: Michael S. Tsirkin <mst@redhat.com>

A VM with mlx5 vDPA has below warnings while being reset:

vhost VQ 0 ring restore failed: -1: Resource temporarily unavailable (11)
vhost VQ 1 ring restore failed: -1: Resource temporarily unavailable (11)

We should allow userspace emulating the virtio device be
able to get to vq's avail_index, regardless of vDPA device
status. Save the index that was last seen when virtq was
stopped, so that userspace doesn't complain.
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Link: https://lore.kernel.org/r/1601583511-15138-1-git-send-email-si-wei.liu@oracle.comSigned-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Eli Cohen <elic@nvidia.com>

Add usb ids of the Cellient MPL200 card.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

De-referencing skb after call to gro_cells_receive() is not allowed.
We need to fetch skb->len earlier.

Fixes: 5491e7c6 ("macsec: enable GRO and RPS on macsec devices")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Some firmware files trigger a PHY soft reset and don't wait for it to
be finished. PHY register writes directly after applying the firmware
may fail or provide unexpected results therefore. Fix this by waiting
for bit BMCR_RESET to be cleared after applying firmware.

There's nothing wrong with the referenced change, it's just that the
fix will apply cleanly only after this change.

Fixes: 89fbd26c ("r8169: fix firmware not resetting tp->ocp_base")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

With multiple DNAT rules it's possible that after destination
translation the resulting tuples collide.

For example, two openvswitch flows:
nw_dst=10.0.0.10,tp_dst=10, actions=ct(commit,table=2,nat(dst=20.0.0.1:20))
nw_dst=10.0.0.20,tp_dst=10, actions=ct(commit,table=2,nat(dst=20.0.0.1:20))

Assuming two TCP clients initiating the following connections:
10.0.0.10:5000->10.0.0.10:10
10.0.0.10:5000->10.0.0.20:10

Both tuples would translate to 10.0.0.10:5000->20.0.0.1:20 causing
nf_conntrack_confirm() to fail because of tuple collision.

Netfilter handles this case by allocating a null binding for SNAT at
egress by default.  Perform the same operation in openvswitch for DNAT
if no explicit SNAT is requested by the user and allocate a null binding
for SNAT for packets in the "original" direction.

Reported-at: https://bugzilla.redhat.com/1877128Suggested-by: Florian Westphal <fw@strlen.de>
Fixes: 05752523 ("openvswitch: Interface with NAT.")
Signed-off-by: Dumitru Ceara <dceara@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

After freeing ep->auth_hmacs we have to clear the pointer
or risk use-after-free as reported by syzbot:

BUG: KASAN: use-after-free in sctp_auth_destroy_hmacs net/sctp/auth.c:509 [inline]
BUG: KASAN: use-after-free in sctp_auth_destroy_hmacs net/sctp/auth.c:501 [inline]
BUG: KASAN: use-after-free in sctp_auth_free+0x17e/0x1d0 net/sctp/auth.c:1070
Read of size 8 at addr ffff8880a8ff52c0 by task syz-executor941/6874

CPU: 0 PID: 6874 Comm: syz-executor941 Not tainted 5.9.0-rc8-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x198/0x1fd lib/dump_stack.c:118
 print_address_description.constprop.0.cold+0xae/0x497 mm/kasan/report.c:383
 __kasan_report mm/kasan/report.c:513 [inline]
 kasan_report.cold+0x1f/0x37 mm/kasan/report.c:530
 sctp_auth_destroy_hmacs net/sctp/auth.c:509 [inline]
 sctp_auth_destroy_hmacs net/sctp/auth.c:501 [inline]
 sctp_auth_free+0x17e/0x1d0 net/sctp/auth.c:1070
 sctp_endpoint_destroy+0x95/0x240 net/sctp/endpointola.c:203
 sctp_endpoint_put net/sctp/endpointola.c:236 [inline]
 sctp_endpoint_free+0xd6/0x110 net/sctp/endpointola.c:183
 sctp_destroy_sock+0x9c/0x3c0 net/sctp/socket.c:4981
 sctp_v6_destroy_sock+0x11/0x20 net/sctp/socket.c:9415
 sk_common_release+0x64/0x390 net/core/sock.c:3254
 sctp_close+0x4ce/0x8b0 net/sctp/socket.c:1533
 inet_release+0x12e/0x280 net/ipv4/af_inet.c:431
 inet6_release+0x4c/0x70 net/ipv6/af_inet6.c:475
 __sock_release+0xcd/0x280 net/socket.c:596
 sock_close+0x18/0x20 net/socket.c:1277
 __fput+0x285/0x920 fs/file_table.c:281
 task_work_run+0xdd/0x190 kernel/task_work.c:141
 exit_task_work include/linux/task_work.h:25 [inline]
 do_exit+0xb7d/0x29f0 kernel/exit.c:806
 do_group_exit+0x125/0x310 kernel/exit.c:903
 __do_sys_exit_group kernel/exit.c:914 [inline]
 __se_sys_exit_group kernel/exit.c:912 [inline]
 __x64_sys_exit_group+0x3a/0x50 kernel/exit.c:912
 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x43f278
Code: Bad RIP value.
RSP: 002b:00007fffe0995c38 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 000000000043f278
RDX: 0000000000000000 RSI: 000000000000003c RDI: 0000000000000000
RBP: 00000000004bf068 R08: 00000000000000e7 R09: ffffffffffffffd0
R10: 0000000020000000 R11: 0000000000000246 R12: 0000000000000001
R13: 00000000006d1180 R14: 0000000000000000 R15: 0000000000000000

Allocated by task 6874:
 kasan_save_stack+0x1b/0x40 mm/kasan/common.c:48
 kasan_set_track mm/kasan/common.c:56 [inline]
 __kasan_kmalloc.constprop.0+0xbf/0xd0 mm/kasan/common.c:461
 kmem_cache_alloc_trace+0x174/0x300 mm/slab.c:3554
 kmalloc include/linux/slab.h:554 [inline]
 kmalloc_array include/linux/slab.h:593 [inline]
 kcalloc include/linux/slab.h:605 [inline]
 sctp_auth_init_hmacs+0xdb/0x3b0 net/sctp/auth.c:464
 sctp_auth_init+0x8a/0x4a0 net/sctp/auth.c:1049
 sctp_setsockopt_auth_supported net/sctp/socket.c:4354 [inline]
 sctp_setsockopt+0x477e/0x97f0 net/sctp/socket.c:4631
 __sys_setsockopt+0x2db/0x610 net/socket.c:2132
 __do_sys_setsockopt net/socket.c:2143 [inline]
 __se_sys_setsockopt net/socket.c:2140 [inline]
 __x64_sys_setsockopt+0xba/0x150 net/socket.c:2140
 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Freed by task 6874:
 kasan_save_stack+0x1b/0x40 mm/kasan/common.c:48
 kasan_set_track+0x1c/0x30 mm/kasan/common.c:56
 kasan_set_free_info+0x1b/0x30 mm/kasan/generic.c:355
 __kasan_slab_free+0xd8/0x120 mm/kasan/common.c:422
 __cache_free mm/slab.c:3422 [inline]
 kfree+0x10e/0x2b0 mm/slab.c:3760
 sctp_auth_destroy_hmacs net/sctp/auth.c:511 [inline]
 sctp_auth_destroy_hmacs net/sctp/auth.c:501 [inline]
 sctp_auth_init_hmacs net/sctp/auth.c:496 [inline]
 sctp_auth_init_hmacs+0x2b7/0x3b0 net/sctp/auth.c:454
 sctp_auth_init+0x8a/0x4a0 net/sctp/auth.c:1049
 sctp_setsockopt_auth_supported net/sctp/socket.c:4354 [inline]
 sctp_setsockopt+0x477e/0x97f0 net/sctp/socket.c:4631
 __sys_setsockopt+0x2db/0x610 net/socket.c:2132
 __do_sys_setsockopt net/socket.c:2143 [inline]
 __se_sys_setsockopt net/socket.c:2140 [inline]
 __x64_sys_setsockopt+0xba/0x150 net/socket.c:2140
 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: 1f485649 ("[SCTP]: Implement SCTP-AUTH internals")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'mac80211-for-net-2020-10-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
pull-request: mac80211 2020-10-08

A single fix for missing input validation in nl80211.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Daniel Borkmann says:

====================
pull-request: bpf 2020-10-08

The main changes are:

1) Fix "unresolved symbol" build error under CONFIG_NET w/o CONFIG_INET due
   to missing tcp_timewait_sock and inet_timewait_sock BTF, from Yonghong Song.

2) Fix 32 bit sub-register bounds tracking for OR case, from Daniel Borkmann.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This commit is correcting NETLINK br_fill_ifinfo() to be able to
handle 'filter_mask' with multiple flags asserted.

Fixes: 36a8e8e2 ("bridge: Extend br_fill_ifinfo to return MPR status")
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Suggested-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull drm nouveau fixes from Dave Airlie:
 "Karol found two last minute nouveau fixes, they both fix crashes, the
  TTM one follows what other drivers do already, and the other is for
  bailing on load on unrecognised chipsets.

   - fix crash in TTM alloc fail path

   - return error earlier for unknown chipsets"

* tag 'drm-fixes-2020-10-08' of git://anongit.freedesktop.org/drm/drm:
  drm/nouveau/mem: guard against NULL pointer access in mem_del
  drm/nouveau/device: return error for unknown chipsets

Pull exfat fixes from Namjae Jeon:

 - Fix use of uninitialized spinlock on error path

 - Fix missing err assignment in exfat_build_inode()

* tag 'exfat-for-5.9-rc9' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/exfat:
  exfat: fix use of uninitialized spinlock on error path
  exfat: fix pointer error checking