The LDC handshake could have been asynchronously triggered
after ldc_bind() enables the ldc_rx() receive interrupt-handler
(and thus intercepts incoming control packets)
and before vio_port_up() calls ldc_connect(). If that is the case,
ldc_connect() should return 0 and let the state-machine
progress.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Karl Volz <karl.volz@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Based almost entirely upon a patch by Christopher Alexander Tobias
Schulze.

In commit db64fe02 ("mm: rewrite vmap
layer") lazy VMAP tlb flushing was added to the vmalloc layer.  This
causes problems on sparc64.

Sparc64 has two VMAP mapped regions and they are not contiguous with
eachother.  First we have the malloc mapping area, then another
unrelated region, then the vmalloc region.

This "another unrelated region" is where the firmware is mapped.

If the lazy TLB flushing logic in the vmalloc code triggers after
we've had both a module unload and a vfree or similar, it will pass an
address range that goes from somewhere inside the malloc region to
somewhere inside the vmalloc region, and thus covering the
openfirmware area entirely.

The sparc64 kernel learns about openfirmware's dynamic mappings in
this region early in the boot, and then services TLB misses in this
area.  But openfirmware has some locked TLB entries which are not
mentioned in those dynamic mappings and we should thus not disturb
them.

These huge lazy TLB flush ranges causes those openfirmware locked TLB
entries to be removed, resulting in all kinds of problems including
hard hangs and crashes during reboot/reset.

Besides causing problems like this, such huge TLB flush ranges are
also incredibly inefficient.  A plea has been made with the author of
the VMAP lazy TLB flushing code, but for now we'll put a safety guard
into our flush_tlb_kernel_range() implementation.

Since the implementation has become non-trivial, stop defining it as a
macro and instead make it a function in a C source file.
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix detection of BREAK on sunsab serial console: BREAK detection was only
performed when there were also serial characters received simultaneously.
To handle all BREAKs correctly, the check for BREAK and the corresponding
call to uart_handle_break() must also be done if count == 0, therefore
duplicate this code fragment and pull it out of the loop over the received
characters.

Patch applies to 3.16-rc6.
Signed-off-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix regression in bbc i2c temperature and fan control on some Sun systems
that causes the driver to refuse to load due to the bbc_i2c_bussel resource not
being present on the (second) i2c bus where the temperature sensors and fan
control are located. (The check for the number of resources was removed when
the driver was ported to a pure OF driver in mid 2008.)
Signed-off-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The assumption was that update_mmu_cache() (and the equivalent for PMDs) would
only be called when the PTE being installed will be accessible by the user.

This is not true for code paths originating from remove_migration_pte().

There are dire consequences for placing a non-valid PTE into the TSB.  The TLB
miss frramework assumes thatwhen a TSB entry matches we can just load it into
the TLB and return from the TLB miss trap.

So if a non-valid PTE is in there, we will deadlock taking the TLB miss over
and over, never satisfying the miss.

Just exit early from update_mmu_cache() and friends in this situation.

Based upon a report and patch from Christopher Alexander Tobias Schulze.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull ARM AES crypto fixes from Herbert Xu:
 "This push fixes a regression on ARM where odd-sized blocks supplied to
  AES may cause crashes"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: arm-aes - fix encryption of unaligned data
  crypto: arm64-aes - fix encryption of unaligned data

Pull powerpc fixes from Ben Herrenschmidt:
 "Here are 3 more small powerpc fixes that should still go into .16.

  One is a recent regression (MMCR2 business), the other is a trivial
  endian fix without which FW updates won't work on LE in IBM machines,
  and the 3rd one turns a BUG_ON into a WARN_ON which is definitely a
  LOT more friendly especially when the whole thing is about retrieving
  error logs ..."

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: Fix endianness of flash_block_list in rtas_flash
  powerpc/powernv: Change BUG_ON to WARN_ON in elog code
  powerpc/perf: Fix MMCR2 handling for EBB

Fix the same alignment bug as in arm64 - we need to pass residue
unprocessed bytes as the last argument to blkcipher_walk_done.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org	# 3.13+
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

cryptsetup fails on arm64 when using kernel encryption via AF_ALG socket.
See https://bugzilla.redhat.com/show_bug.cgi?id=1122937

The bug is caused by incorrect handling of unaligned data in
arch/arm64/crypto/aes-glue.c. Cryptsetup creates a buffer that is aligned
on 8 bytes, but not on 16 bytes. It opens AF_ALG socket and uses the
socket to encrypt data in the buffer. The arm64 crypto accelerator causes
data corruption or crashes in the scatterwalk_pagedone.

This patch fixes the bug by passing the residue bytes that were not
processed as the last parameter to blkcipher_walk_done.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The function rtas_flash_firmware passes the address of a data structure,
flash_block_list, when making the update-flash-64-and-reboot rtas call.
While the endianness of the address is handled correctly, the endianness
of the data is not.  This patch ensures that the data in flash_block_list
is big endian when passed to rtas on little endian hosts.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

We can continue to read the error log (up to MAX size) even if
we get the elog size more than MAX size. Hence change BUG_ON to
WARN_ON.

Also updated error message.
Reported-by: Gopesh Kumar Chaudhary <gopchaud@in.ibm.com>
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Pull perf fixes from Thomas Gleixner:
 "A bunch of fixes for perf and kprobes:
   - revert a commit that caused a perf group regression
   - silence dmesg spam
   - fix kprobe probing errors on ia64 and ppc64
   - filter kprobe faults from userspace
   - lockdep fix for perf exit path
   - prevent perf #GP in KVM guest
   - correct perf event and filters"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  kprobes: Fix "Failed to find blacklist" probing errors on ia64 and ppc64
  kprobes/x86: Don't try to resolve kprobe faults from userspace
  perf/x86/intel: Avoid spamming kernel log for BTS buffer failure
  perf/x86/intel: Protect LBR and extra_regs against KVM lying
  perf: Fix lockdep warning on process exit
  perf/x86/intel/uncore: Fix SNB-EP/IVT Cbox filter mappings
  perf/x86/intel: Use proper dTLB-load-misses event on IvyBridge
  perf: Revert ("perf: Always destroy groups on exit")

Pull x86 fixes from Peter Anvin:
 "A couple of crash fixes, plus a fix that on 32 bits would cause a
  missing -ENOSYS for nonexistent system calls"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, cpu: Fix cache topology for early P4-SMT
  x86_32, entry: Store badsys error code in %eax
  x86, MCE: Robustify mcheck_init_device

Pull vfs fixes from Christoph Hellwig:
 "A vfsmount leak fix, and a compile warning fix"

* 'vfs-for-3.16' of git://git.infradead.org/users/hch/vfs:
  fs: umount on symlink leaks mnt count
  direct-io: fix uninitialized warning in do_direct_IO()

Pull firewire regression fix from Stefan Richter:
 "IEEE 1394 (FireWire) subsystem fix: MSI don't work on VIA PCIe
  controllers with some isochronous workloads (regression since
  v3.16-rc1)"

* tag 'firewire-fix-vt6315' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
  firewire: ohci: disable MSI for VIA VT6315 again

Michel Dänzer and a couple of other people reported inexplicable random
oopses in the scheduler, and the cause turns out to be gcc mis-compiling
the load_balance() function when debugging is enabled.  The gcc bug
apparently goes back to gcc-4.5, but slight optimization changes means
that it now showed up as a problem in 4.9.0 and 4.9.1.

The instruction scheduling problem causes gcc to schedule a spill
operation to before the stack frame has been created, which in turn can
corrupt the spilled value if an interrupt comes in.  There may be other
effects of this bug too, but that's the code generation problem seen in
Michel's case.

This is fixed in current gcc HEAD, but the workaround as suggested by
Markus Trippelsdorf is pretty simple: use -fno-var-tracking-assignments
when compiling the kernel, which disables the gcc code that causes the
problem.  This can result in slightly worse debug information for
variable accesses, but that is infinitely preferable to actual code
generation problems.

Doing this unconditionally (not just for CONFIG_DEBUG_INFO) also allows
non-debug builds to verify that the debug build would be identical: we
can do

    export GCC_COMPARE_DEBUG=1

to make gcc internally verify that the result of the build is
independent of the "-g" flag (it will make the compiler build everything
twice, toggling the debug flag, and compare the results).

Without the "-fno-var-tracking-assignments" option, the build would fail
(even with 4.8.3 that didn't show the actual stack frame bug) with a gcc
compare failure.

See also gcc bugzilla:

  https://gcc.gnu.org/bugzilla/show_bug.cgi?id=61801Reported-by: Michel Dänzer <michel@daenzer.net>
Suggested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Jakub Jelinek <jakub@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Shortly before 3.16-rc1, Dave Jones reported:

  WARNING: CPU: 3 PID: 19721 at fs/xfs/xfs_aops.c:971
           xfs_vm_writepage+0x5ce/0x630 [xfs]()
  CPU: 3 PID: 19721 Comm: trinity-c61 Not tainted 3.15.0+ #3
  Call Trace:
    xfs_vm_writepage+0x5ce/0x630 [xfs]
    shrink_page_list+0x8f9/0xb90
    shrink_inactive_list+0x253/0x510
    shrink_lruvec+0x563/0x6c0
    shrink_zone+0x3b/0x100
    shrink_zones+0x1f1/0x3c0
    try_to_free_pages+0x164/0x380
    __alloc_pages_nodemask+0x822/0xc90
    alloc_pages_vma+0xaf/0x1c0
    handle_mm_fault+0xa31/0xc50
  etc.

 970   if (WARN_ON_ONCE((current->flags & (PF_MEMALLOC|PF_KSWAPD)) ==
 971                   PF_MEMALLOC))

I did not respond at the time, because a glance at the PageDirty block
in shrink_page_list() quickly shows that this is impossible: we don't do
writeback on file pages (other than tmpfs) from direct reclaim nowadays.
Dave was hallucinating, but it would have been disrespectful to say so.

However, my own /var/log/messages now shows similar complaints

  WARNING: CPU: 1 PID: 28814 at fs/ext4/inode.c:1881 ext4_writepage+0xa7/0x38b()
  WARNING: CPU: 0 PID: 27347 at fs/ext4/inode.c:1764 ext4_writepage+0xa7/0x38b()

from stressing some mmotm trees during July.

Could a dirty xfs or ext4 file page somehow get marked PageSwapBacked,
so fail shrink_page_list()'s page_is_file_cache() test, and so proceed
to mapping->a_ops->writepage()?

Yes, 3.16-rc1's commit 68711a74 ("mm, migration: add destination
page freeing callback") has provided such a way to compaction: if
migrating a SwapBacked page fails, its newpage may be put back on the
list for later use with PageSwapBacked still set, and nothing will clear
it.

Whether that can do anything worse than issue WARN_ON_ONCEs, and get
some statistics wrong, is unclear: easier to fix than to think through
the consequences.

Fixing it here, before the put_new_page(), addresses the bug directly,
but is probably the worst place to fix it.  Page migration is doing too
many parts of the job on too many levels: fixing it in
move_to_new_page() to complement its SetPageSwapBacked would be
preferable, except why is it (and newpage->mapping and newpage->index)
done there, rather than down in migrate_page_move_mapping(), once we are
sure of success? Not a cleanup to get into right now, especially not
with memcg cleanups coming in 3.17.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull drm fixes from Dave Airlie:
 "This is radeon and intel fixes, and is a small bit larger than I'm
  guessing you'd like it to be.

   - i915: fixes 32-bit highmem i915 blank screen, semaphore hang and
     runtime pm fix

   - radeon: gpuvm stability fix for hangs since 3.15, and hang/reboot
     regression on TN/RL devices,

  The only slightly controversial one is the change to use GB for the
  vm_size, which I'm letting through as its a new interface we defined
  in this merge window, and I'd prefer to have the released kernel have
  the final interface rather than changing it later"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon: fix cut and paste issue for hawaii.
  drm/radeon: fix irq ring buffer overflow handling
  drm/i915: Simplify i915_gem_release_all_mmaps()
  drm/radeon: fix error handling in radeon_vm_bo_set_addr
  drm/i915: fix freeze with blank screen booting highmem
  drm/i915: Reorder the semaphore deadlock check, again
  drm/radeon/TN: only enable bapm on MSI systems
  drm/radeon: fix VM IB handling
  drm/radeon: fix handling of radeon_vm_bo_rmv v3
  drm/radeon: let's use GB for vm_size (v2)

Pull sound fixes from Takashi Iwai:
 "Here contains only the fixes for the new FireWire bebob driver.  All
  fairly trivial and local fixes, so safe to apply"

* tag 'sound-3.16-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: bebob: Correction for return value of special_clk_ctl_put() in error
  ALSA: bebob: Correction for return value of .put callback
  ALSA: bebob: Use different labels for digital input/output
  ALSA: bebob: Fix a missing to unlock mutex in error handling case

Pull hwmon fix from Guenter Roeck:
 "Fixes to temperature limit and vrm write operations in smsc47m192
  driver"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (smsc47m192) Fix temperature limit and vrm write operations

Do not split the PARPORT-related symbols with the new kconfig
symbol ARCH_MIGHT_HAVE_PC_PARPORT. The split was causing incorrect
display of these symbols -- they were not being displayed together
as they should be.

Fixes: d90c3eb3 "Kconfig cleanup (PARPORT_PC dependencies)"
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: stable@vger.kernel.org # for 3.13, 3.14, 3.15
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'blackfin-3.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux

Pull blackfin fixes from Steven Miao:
 "smc nor flash PM fix, pinctrl group fix, update defconfig, and build
  fixes"

* tag 'blackfin-3.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
  blackfin: vmlinux.lds.S: reserve 32 bytes space at the end of data section for XIP kernel
  defconfig: BF609: update spi config name
  irq: blackfin sec: drop duplicated sec priority set
  blackfin: bind different groups of one pinmux function to different state name
  blackfin: fix some bf5xx boards build for missing <linux/gpio.h>
  pm: bf609: cleanup smc nor flash

to collect some undefined section to the end of the data section and avoid section overlap
Signed-off-by: Steven Miao <realmz6@gmail.com>

Signed-off-by: Steven Miao <realmz6@gmail.com>

Signed-off-by: Steven Miao <realmz6@gmail.com>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>

Signed-off-by: Steven Miao <realmz6@gmail.com>

drop smc pin state change code, pin state will be saved in pinctrl-adi2 driver
cleanup nor flash init/exit for pm suspend/resume
Signed-off-by: Steven Miao <realmz6@gmail.com>

Pull parisc fixes from Helge Deller:
 "We have two trivial patches in here.  One removes the SA_RESTORER
  #define since on parisc we don't have the sa_restorer field in struct
  sigaction, the other patch removes an unnecessary memset().

  The SA_RESTORER removal patch is scheduled for stable trees, since
  without it some userspace apps don't build"

* 'parisc-3.16-6' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Eliminate memset after alloc_bootmem_pages
  parisc: Remove SA_RESTORER define

Pull fuse fixes from Miklos Szeredi:
 "These two pathes fix issues with the kernel-userspace protocol changes
  in v3.15"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: add FUSE_NO_OPEN_SUPPORT flag to INIT
  fuse: s_time_gran fix

Promote one fix for 3.16

This fix was necessary after

9c15a24b ("x86/mce: Improve mcheck_init_device() error handling")

went in. What this patch did was, among others, check the return value
of misc_register and exit early if it encountered an error. Original
code sloppily didn't do that.

However,

        cef12ee5 ("xen/mce: Add mcelog support for Xen platform")

made it so that xen's init routine xen_late_init_mcelog runs first. This
was needed for the xen mcelog device which is supposed to be independent
from the baremetal one.

Initially it was reported that misc_register() fails often on xen and
that's why it needed fixing. However, it is *supposed* to fail by
design, when running in dom0 so that the xen mcelog device file gets
registered first.

And *then* you need the notifier *not* unregistered on the error path so
that the timer does get deleted properly in the CPU hotplug notifier.

Btw, this fix is needed also on baremetal in the unlikely event that
misc_register(&mce_chrdev_device) fails there too.

I was unsure whether to rush it in now and decided to delay it to 3.17.
However, xen people wanted it promoted as it breaks xen when doing cpu
hotplug there. So, after a bit of simmering in tip/master for initial
smoke testing, let's move it to 3.16. It fixes a semi-regression which
got introduced in 3.16 so no need for stable tagging.

tip/x86/ras contains that exact same commit but we can't remove it
there as it is not the last one. It won't cause any merge issues, as I
confirmed locally but I should state here the special situation of this
one fix explicitly anyway.

Thanks.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>

This is a halfway fix for hawaii acceleration. More fixes to come
but hopefully isolated to userspace.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

two more radeon fixes.

* 'drm-fixes-3.16' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: fix irq ring buffer overflow handling
  drm/radeon: fix error handling in radeon_vm_bo_set_addr

This time in time! Just 32bit-pae fix from Hugh, semaphores fun from Chris
and a fix for runtime pm cherry-picked from next.

Paulo is still working on a fix for runtime pm when X does cursor fun when
the display is off, but that one isn't ready yet.

* tag 'drm-intel-fixes-2014-07-24' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Simplify i915_gem_release_all_mmaps()
  drm/i915: fix freeze with blank screen booting highmem
  drm/i915: Reorder the semaphore deadlock check, again

alloc_bootmem and related function always return zeroed region of
memory. Thus a memset after calls to these functions is unnecessary.

The following Coccinelle semantic patch was used for making the change:

@@
expression E,E1;
@@

E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\)(...)
... when != E
- memset(E,0,E1);
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Helge Deller <deller@gmx.de>

The sa_restorer field in struct sigaction is obsolete and no longer in
the parisc implementation.  However, the core code assumes the field is
present if SA_RESTORER is defined. So, the define needs to be removed.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>

Temperature limit clamps are applied after converting the temperature
from milli-degrees C to degrees C, so either the clamp limit needs
to be specified in degrees C, not milli-degrees C, or clamping must
happen before converting to degrees C. Use the latter method to avoid
overflows.

vrm is an u8, so the written value needs to be limited to [0, 255].

Cc: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>

Currently umount on symlink blocks following umount:

/vz is separate mount

# ls /vz/ -al | grep test
drwxr-xr-x.  2 root root       4096 Jul 19 01:14 testdir
lrwxrwxrwx.  1 root root         11 Jul 19 01:16 testlink -> /vz/testdir
# umount -l /vz/testlink
umount: /vz/testlink: not mounted (expected)

# lsof /vz
# umount /vz
umount: /vz: device is busy. (unexpected)

In this case mountpoint_last() gets an extra refcount on path->mnt
Signed-off-by: Vasily Averin <vvs@openvz.org>
Acked-by: Ian Kent <raven@themaw.net>
Acked-by: Jeff Layton <jlayton@primarydata.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>

The following warnings:

  fs/direct-io.c: In function ‘__blockdev_direct_IO’:
  fs/direct-io.c:1011:12: warning: ‘to’ may be used uninitialized in this function [-Wmaybe-uninitialized]
  fs/direct-io.c:913:16: note: ‘to’ was declared here
  fs/direct-io.c:1011:12: warning: ‘from’ may be used uninitialized in this function [-Wmaybe-uninitialized]
  fs/direct-io.c:913:10: note: ‘from’ was declared here

are false positive because dio_get_page() either fails, or sets both
'from' and 'to'.

Paul Bolle said ...
Maybe it's better to move initializing "to" and "from" out of
dio_get_page(). That _might_ make it easier for both the the reader and
the compiler to understand what's going on. Something like this:

Christoph Hellwig said ...
The fix of moving the code definitively looks nicer, while I think
uninitialized_var is horrible wart that won't get anywhere near my code.

Boaz Harrosh: I agree with Christoph and Paul
Signed-off-by: Boaz Harrosh <boaz@plexistor.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>