Merge tag 'usb-serial-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

Johan writes:

USB-serial fixes for v3.18-rc4

Two fixes of non-atomic allocations in write paths.
Signed-off-by: Johan Hovold <johan@kernel.org>

The USB OTG port does not work since v3.16 on omap platform.
This is a regression introduced by the commit
eb82a3d8 (phy: omap-usb2: Balance pm_runtime_enable() on probe failure
 and remove).
This because the call to pm_runtime_enable() function is moved after the
call to devm_phy_create() function, which has side effect since later in
the subsequent calls of devm_phy_create() there is a check with
pm_runtime_enabled() to configure few things.

Fixes: eb82a3d8Signed-off-by: Oussama Ghorbel <ghorbel@pivasoftware.com>
Tested-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The timeout argument to usb_stor_control_msg() is specified in jiffies, not
milliseconds.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure to only raise DTR on transitions from B0 in set_termios.

Also allow set_termios to be called from open with a termios_old of
NULL. Note that DTR will not be raised prematurely in this case.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit bda9893c as it was
incorrect.
Reported-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It is safe to call notify disconnect when the usb core
thinks the device is disconnected.

This commit also fixes one bug found at below situation:
we have not enabled usb wakeup, we do system suspend when
there is an usb device at the port, after suspend, we plug out
the usb device, then plug in device again. At that time,
the nofity disconnect was not called at current code, as
the controller doesn't know the usb device was disconnected
during the suspend, but USB core knows the port has changed
during that periods.

So to fix this problem, and let the usb core call notify disconnect.

Cc: 3.17+ <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since we notify disconnecting based on the usb device is existed
(port_dev->child, the child device at roothub is not NULL), we
need to notify connect after device has been registered.

This fixes a bug that do fast plug in/out test, and the notify_disconnect
is not called due to roothub child is NULL and the enumeration has failed.

Cc: v3.17+ <stable@vger.kernel.org>
Signed-off-by: Tony Zheng <Tony.Zheng@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X
quirk to filter these out.

Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The switch back is limited to ULT even on HP. The contrary
finding arose by bad luck in BIOS versions for testing.
This fixes spontaneous resume from S3 on some HP laptops.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Yet another device affected by this.
Tested-by: Kevin Fenzi <kevin@scrye.com>
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently this quirk is enabled for the model with the device id 0x0089, it
is needed for the 0x009b model, which is found on the Fujitsu Lifebook u904
as well.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The usbip driver was moved out of staging in 3.17-rc3 but the MAINTAINERS file
still has the old staging entry as well as the new one. Remove the old entry.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Functions fw5895_init() and config_autodelink_before_power_down() are used
only when CONFIG_PM is defined.

drivers/usb/storage/realtek_cr.c:699:13: warning: 'fw5895_init' defined but not used [-Wunused-function]
drivers/usb/storage/realtek_cr.c:629:12: warning: 'config_autodelink_before_power_down' defined but not used [-Wunused-function]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The PLAT_S5P Kconfig symbol was removed in commit d78c16cc
("ARM: SAMSUNG: Remove remaining legacy code"). There are still
some references left, fix that by replacing them with ARCH_S5PV210.

Fixes: d78c16cc ("ARM: SAMSUNG: Remove remaining legacy code")
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Just like some Seagate enclosures, these devices do not seem to grok ata
pass through commands.

Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Streams seem to be broken on the Asmedia 1042. An uas capable Seagate disk
which is known to work fine with other controllers causes the system to freeze
when connected over usb-3 with this controller, where as it works fine with
uas in usb-2 ports, indicating a problem with streams.

This is a bit bigger hammer then I would like to use for this, but for now it
will have to make do. I've ordered a pci-e usb controller card with an Asmedia
1042, once that arrives I'll try to get streams to work (with a quirk flag if
necessary) and then we can re-enable them. For now this at least makes uas
capable disk enclosures work again by forcing fallback to the usb-storage
driver.
Reported-by: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We wanted to print the version as (major).(minor) but because the shift
operation is higher precedence than the mask then we print
(minor).(minor).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X
quirk to filter these out.

Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Sometimes mass-storage devices using the Bulk-only transport will
mistakenly skip the data phase of a command.  Rather than sending the
data expected by the host or sending a zero-length packet, they go
directly to the status phase and send the CSW.

This causes problems for usb-storage, for obvious reasons.  The driver
will interpret the CSW as a short data transfer and will wait to
receive a CSW.  The device won't have anything left to send, so the
command eventually times out.

The SCSI layer doesn't retry commands after they time out (this is a
relatively recent change).  Therefore we should do our best to detect
a skipped data phase and handle it promptly.

This patch adds code to do that.  If usb-storage receives a short
13-byte data transfer from the device, and if the first four bytes of
the data match the CSW signature, the driver will set the residue to
the full transfer length and interpret the data as a CSW.

This fixes Bugzilla #86611.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Tested-by: Paul Osmialowski <newchief@king.net.pl>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit fixes the following oops:

[10238.622067] scsi host3: uas_eh_bus_reset_handler start
[10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10245.779365] usb 3-4: device descriptor read/8, error -110
[10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10250.897603] usb 3-4: device descriptor read/8, error -110
[10251.058200] BUG: unable to handle kernel NULL pointer dereference at  0000000000000040
[10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140
<snip>
[10251.059473] Call Trace:
[10251.059487]  [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130
[10251.059520]  [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0
[10251.059548]  [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0
[10251.059575]  [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100
[10251.059601]  [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70
[10251.059635]  [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0
[10251.059662]  [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas]
[10251.059694]  [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas]
[10251.059722]  [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0
[10251.059749]  [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas]
[10251.059781]  [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110
[10251.059808]  [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270
<snip>

The problem is the following call sequence (simplified):

1) usb_reset_device
2)  usb_reset_and_verify_device
2)   hub_port_init
3)    hub_port_finish_reset
3)     xhci_discover_or_reset_device
        This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0
4)    usb_get_device_descriptor
       This fails
5)   hub_port_init fails
6)  usb_reset_and_verify_device fails, does not restore device config
7)  uas_post_reset
8)   xhci_alloc_streams
      NULL deref on the free-ed ring

This commit fixes this by not allowing usb_alloc_streams to continue if
the device is not configured.

Note that we do allow usb_free_streams to continue after a (logical)
disconnect, as it is necessary to explicitly free the streams at the xhci
controller level.

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver wasn't properly configuring the hardware for the current
termios settings under all conditions.  Ensure that termios are
written to the device when the port is activated.
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add device-id entry for GW Instek AFG-2225, which has a byte swapped
bInterfaceSubClass (0x20).
Reported-by: Karl Palsson <karlp@tweak.net.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Write may be called from interrupt context so make sure to use
GFP_ATOMIC for all allocations in write.

Fixes: 0d930e51 ("USB: opticon: Add Opticon OPN2001 write support")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Write may be called from interrupt context so make sure to use
GFP_ATOMIC for all allocations in write.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Pull MTD fixes from Brian Norris:
 "Three main MTD fixes for 3.18:

   - A regression from 3.16 which was noticed in 3.17.  With the
     restructuring of the m25p80.c driver and the SPI NOR library
     framework, we omitted proper listing of the SPI device IDs.  This
     means m25p80.c wouldn't auto-load (modprobe) properly when built as
     a module.  For now, we duplicate the device IDs into both modules.

   - The OMAP / ELM modules were depending on an implicit link ordering.
     Use deferred probing so that the new link order (in 3.18-rc) can
     still allow for successful probing.

   - Fix suspend/resume support for LH28F640BF NOR flash"

* tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd:
  mtd: cfi_cmdset_0001.c: fix resume for LH28F640BF chips
  mtd: omap: fix mtd devices not showing up
  mtd: m25p80,spi-nor: Fix module aliases for m25p80
  mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
  mtd: m25p80: get rid of spi_get_device_id

Pull SCSI fixes from James Bottomley:
 "This is a set of six patches consisting of:
   - two MAINTAINER updates
   - two scsi-mq fixs for the old parallel interface (not every request
     is tagged and we need to set the right flags to populate the SPI
     tag message)
   - a fix for a memory leak in scatterlist traversal caused by a
     preallocation update in 3.17
   - an ipv6 fix for cxgbi"

[ The scatterlist fix also came in separately through the block layer tree ]

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  MAINTAINERS: ufs - remove self
  MAINTAINERS: change hpsa and cciss maintainer
  libcxgbi : support ipv6 address host_param
  scsi: set REQ_QUEUE for the blk-mq case
  Revert "block: all blk-mq requests are tagged"
  lib/scatterlist: fix memory leak with scsi-mq

Pull drm fixes from Dave Airlie:
 "Nothing too astounding or major: radeon, i915, vmwgfx, armada and
  exynos.

  Biggest ones:
   - vmwgfx has one big locking regression fix
   - i915 has come displayport fixes
   - radeon has some stability and a memory alloc failure
   - armada and exynos have some vblank fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (24 commits)
  drm/exynos: correct connector->dpms field before resuming
  drm/exynos: enable vblank after DPMS on
  drm/exynos: init kms poll at the end of initialization
  drm/exynos: propagate plane initialization errors
  drm/exynos: vidi: fix build warning
  drm/exynos: remove explicit encoder/connector de-initialization
  drm/exynos: init vblank with real number of crtcs
  drm/vmwgfx: Filter out modes those cannot be supported by the current VRAM size.
  drm/vmwgfx: Fix hash key computation
  drm/vmwgfx: fix lock breakage
  drm/i915/dp: only use training pattern 3 on platforms that support it
  drm/radeon: remove some buggy dead code
  drm/i915: Ignore VBT backlight check on Macbook 2, 1
  drm/radeon: remove invalid pci id
  drm/radeon: dpm fixes for asrock systems
  radeon: clean up coding style differences in radeon_get_bios()
  drm/radeon: Use drm_malloc_ab instead of kmalloc_array
  drm/radeon/dpm: disable ulv support on SI
  drm/i915: Fix GMBUSFREQ on vlv/chv
  drm/i915: Ignore long hpds on eDP ports
  ...

Pull ARM fixes from Russell King:
 - add the new bpf syscall to ARM.
 - drop a redundant return statement in __iommu_alloc_remap()
 - fix a performance issue noticed by Thomas Petazzoni with
   kmap_atomic().
 - fix an issue with the L2 cache OF parsing code which caused it to
   incorrectly print warnings on each boot, and make the warning text
   more consistent with the rest of the code

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8180/1: mm: implement no-highmem fast path in kmap_atomic_pfn()
  ARM: 8183/1: l2c: Improve l2c310_of_parse() error message
  ARM: 8181/1: Drop extra return statement
  ARM: 8182/1: l2c: Make l2x0_cache_size_of_parse() return 'int'
  ARM: enable bpf syscall

Pull kvm fixes from Paolo Bonzini:
 "A small set of x86 fixes.  The most serious is an SRCU lockdep fix.

  A bit late - needed some time to test the SRCU fix, which only came in
  on Friday"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: vmx: defer load of APIC access page address during reset
  KVM: nVMX: Disable preemption while reading from shadow VMCS
  KVM: x86: Fix far-jump to non-canonical check
  KVM: emulator: fix execution close to the segment limit
  KVM: emulator: fix error code for __linearize

Merge branch 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes

This pull-request includes some bug fixes and code cleanups.
Especially, this fixes the bind failure issue occurred when it tries
to re-bind Exynos drm driver after unbound, and the modetest failure
issue incurred by not having a pair to vblank on and off requests.

* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
  drm/exynos: correct connector->dpms field before resuming
  drm/exynos: enable vblank after DPMS on
  drm/exynos: init kms poll at the end of initialization
  drm/exynos: propagate plane initialization errors
  drm/exynos: vidi: fix build warning
  drm/exynos: remove explicit encoder/connector de-initialization
  drm/exynos: init vblank with real number of crtcs

Pull VFS fixes from Al Viro:
 "A bunch of assorted fixes, most of them followups to overlayfs merge"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  ovl: initialize ->is_cursor
  Return short read or 0 at end of a raw device, not EIO
  isofs: don't bother with ->d_op for normal case
  isofs_cmp(): we'll never see a dentry for . or ..
  overlayfs: fix lockdep misannotation
  ovl: fix check for cursor
  overlayfs: barriers for opening upper-layer directory
  rcu: Provide counterpart to rcu_dereference() for non-RCU situations
  staging: android: logger: Fix log corruption regression

The sk_prot is irda's own set of protocol handlers, so irda should
statically know what that function is anyway, without using an indirect
pointer.  And as it happens, we know *exactly* what that pointer is
statically: it's NULL, because irda doesn't define a disconnect
operation.

So calling that function is doubly wrong, and will just cause an oops.
Reported-by: Martin Lang <mlg.hessigheim@gmail.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

During system suspend after connector switch off its dpms field
is set to connector previous dpms state. To properly resume dpms field
should be set to its actual state (off) before resuming to previous dpms state.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Before DPMS off driver disables vblank.
It should be balanced by vblank enable after DPMS on.
The patch fixes issue with page_flip ioctl not being able
to acquire vblank counter introduced by patch:
drm: Always reject drm_vblank_get() after drm_vblank_off()
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

HPD events can be generated by components even if drm_dev is not fully
initialized, to skip such events kms poll initialization should
be performed at the end of load callback followed directly by forced
connection detection.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

In case of error during plane initialization load callback
incorrectly return success, this patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

encoder object isn't used anymore so remove it.
Signed-off-by: Inki Dae <inki.dae@samsung.com>

All KMS objects are destroyed by drm_mode_config_cleanup in proper order
so component drivers should not care about it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Initialization of vblank with MAX_CRTC caused attempts
to disabling vblanks for non-existing crtcs in case
drm used fewer crtcs. The patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>