- 20 Nov, 2019 11 commits
-
-
Grygorii Strashko authored
A following patches introduce new CPSW switchdev driver which uses common code with legacy CPSW driver. This will introduce build dependency between CPSW switchdev and CPSW legacy drivers related to for_each_slave() and cpsw_slave_index() - they can be compiled both, but only one of them will be not functional depending in Kconfig settings due to duffrences in Slave Ports indexes calculation. To fix this make for_each_slave() local (it's used now only by legacy CPSW driver) and convert cpsw_slave_index() to be a function pointer which is assigned in probe. Driver to probe is defined by DT. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ilias Apalodimas authored
A following patch introduces switchdev functionality, so modify ALE engine VLANs/MDBs API: - cpsw_ale_del_mcast(): update so it will remove only selected ports from mcast port_mask or delete whole mcast record if !port_mask - cpsw_ale_del_vlan(): update so it will remove only selected ports from all VLAN record's masks or delete whole VLAN record if !port_mask - add cpsw_ale_vlan_add_modify() to add or modify existing VLAN record's masks - add cpsw_ale_set_unreg_mcast() for enabling unreg mcast on port VLANs Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Grygorii Strashko authored
Now untagged vlan traffic is not support on Host P0 port. This patch adds in ALE context bitmap of VLANs for which Host P0 port bit set in Force Untagged Packet Egress bitmask in VLANs ALE entries, and adds corresponding check in VLAN incapsulation header parsing function cpsw_rx_vlan_encap(). Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Grygorii Strashko authored
Clean CPSW ALE on init and intf restart (up/down) to avoid reading obsolete or garbage entries from ALE table. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Pablo Neira Ayuso says: ==================== nf_tables_offload: vlan matching support The following patchset contains Netfilter support for vlan matching offloads: 1) Constify nft_reg_load() as a preparation patch. 2) Restrict rule matching to ingress interface type ARPHRD_ETHER. 3) Add new vlan_tci field to flow_dissector_key_vlan structure, to allow to set up vlan_id, vlan_dei and vlan_priority in one go. 4) C-VLAN matching support. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Pablo Neira Ayuso authored
Match on h_vlan_encapsulated_proto and set up protocol dependency. Check for protocol dependency before accessing the tci field. Allow to match on the encapsulated ethertype too. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Pablo Neira Ayuso authored
Match on ethertype and set up protocol dependency. Check for protocol dependency before accessing the tci field. Allow to match on the encapsulated ethertype too. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Pablo Neira Ayuso authored
Hardware offload support at this stage assumes an ethernet device in place. The flow dissector provides the intermediate representation to express this selector, so extend it to allow to store the interface type. Flower does not uses this, so skb_flow_dissect_meta() is not extended to match on this new field. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Pablo Neira Ayuso authored
This patch constifies the pointer to source register data that is passed as an input parameter. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Xin Long authored
geneve RFC (draft-ietf-nvo3-geneve-14) allows a geneve packet to carry multiple geneve opts, so it's necessary for lwtunnel to support adding multiple geneve opts in one lwtunnel route. But vxlan and erspan opts are still only allowed to add one option. With this patch, iproute2 could make it like: # ip r a 1.1.1.0/24 encap ip id 1 geneve_opts 0:0:12121212,1:2:12121212 \ dst 10.1.0.2 dev geneve1 # ip r a 1.1.1.0/24 encap ip id 1 vxlan_opts 456 \ dst 10.1.0.2 dev erspan1 # ip r a 1.1.1.0/24 encap ip id 1 erspan_opts 1:123:0:0 \ dst 10.1.0.2 dev erspan1 Which are pretty much like cls_flower and act_tunnel_key. Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rahul Lakkireddy authored
Semicolon is not required at the end of switch block. So, remove it. Addresses coccinelle warning: drivers/net/ethernet/chelsio/cxgb4/sge.c:2260:2-3: Unneeded semicolon Fixes: 4846d533 ("cxgb4: add Tx and Rx path for ETHOFLD traffic") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 19 Nov, 2019 29 commits
-
-
Vladimir Oltean authored
On the NXP LS1028A, there are 2 Ethernet links between the Felix switch and the ENETC: - eno2 <-> swp4, at 2.5G - eno3 <-> swp5, at 1G Only one of the above Ethernet port pairs can act as a DSA link for tagging. When adding initial support for the driver, it was tested only on the 1G eno3 <-> swp5 interface, due to the necessity of using PHYLIB initially (which treats fixed-link interfaces as emulated C22 PHYs, so it doesn't support fixed-link speeds higher than 1G). After making PHYLINK work, it appears that swp4 still can't act as CPU port. So it looks like ocelot_set_cpu_port was being called for swp4, but then it was called again for swp5, overwriting the CPU port assigned in the DT. It appears that when you call dsa_upstream_port for a port that is not defined in the device tree (such as swp5 when using swp4 as CPU port), its dp->cpu_dp pointer is not initialized by dsa_tree_setup_default_cpu, and this trips up the following condition in dsa_upstream_port: if (!cpu_dp) return port; So the moral of the story is: don't call dsa_upstream_port for a port that is not defined in the device tree, and therefore its dsa_port structure is not completely initialized (ds->num_ports is still 6). Fixes: 56051948 ("net: dsa: ocelot: add driver for Felix switch family") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Colin Ian King authored
In the case where the call to phy_interface_is_rgmii returns zero the variable ret is left uninitialized and this is returned at the end of the function dp83869_configure_rgmii. Fix this by returning 0 instead of the uninitialized value in ret. Addresses-Coverity: ("Uninitialized scalar variable") Fixes: 01db923e ("net: phy: dp83869: Add TI dp83869 phy") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Xin Long authored
LWTUNNEL_IP_OPT_ERSPAN_VER is u8 type, and nla_put_u8 should have been used instead of nla_put_u32(). This is a copy-paste error. Fixes: b0a21810 ("lwtunnel: add options setting and dumping for erspan") Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: Updates. This series has the firmware interface update that changes the aRFS/ntuple interface on 57500 chips. The 2nd patch adds a counter and improves the hardware buffer error handling on the 57500 chips. The rest of the series is mainly enhancements on error recovery and firmware reset. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Pavan Chebbi authored
This is especially beneficial during the NVRAM related firmware commands that have longer timeouts. If the BNXT_STATE_FW_FATAL_COND flag gets set while waiting for firmware response, abort and return error. Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vasundhara Volam authored
During loss of heartbeat, log this warning message. Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vasundhara Volam authored
For NVM params that are not supported in the current NVM configuration, return the error as -EOPNOTSUPP. Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vasundhara Volam authored
Report health status update to devlink health reporter, once reset is completed. Cc: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vasundhara Volam authored
The Linux driver is capable of being the master function to handle resets, so we set the flag to let firmware know. Some other drivers, such as DPDK, is not capable and will not set the flag. Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vasundhara Volam authored
If firmware supports hot reset, extend ETHTOOL_RESET to support hot reset driver which does not require a driver reload after ETHTOOL_RESET. The driver will go through the same coordinated reset sequence as a firmware initiated fatal/non-fatal reset. Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vasundhara Volam authored
Use the larger HWRM_COREDUMP_TIMEOUT value for coredump related data response from the firmware. These commands take longer than normal commands. Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Michael Chan authored
When hardware reports RX buffer errors, the latest 57500 chips do not require reset. The packet is discarded by the hardware and the ring will continue to operate. Also, add an rx_buf_errors counter for this type of error. It can help the user to identify if the aggregation ring is too small. Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Michael Chan authored
The aRFS ring table interface has changed for the 57500 chips. Updating it accordingly so it will work with the latest production firmware. Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Ido Schimmel says: ==================== selftests: Add ethtool and scale tests This patch set adds generic ethtool tests and a mlxsw-specific router scale test for Spectrum-2. Patches #1-#2 from Danielle add the router scale test for Spectrum-2. It re-uses the same test as Spectrum-1, but it is invoked with a different scale, according to what it is queried from devlink-resource. Patches #3-#5 from Amit are a re-work of the ethtool tests that were posted in the past [1]. Patches #3-#4 add the necessary library routines, whereas patch #5 adds the test itself. The test checks both good and bad flows with autoneg on and off. The test plan it detailed in the commit message. Last time Andrew and Florian (copied) provided very useful feedback that is incorporated in this set. Namely: * Parse the value of the different link modes from /usr/include/linux/ethtool.h * Differentiate between supported and advertised speeds and use the latter in autoneg tests * Make the test generic and move it to net/forwarding/ instead of being mlxsw-specific [1] https://patchwork.ozlabs.org/cover/1112903/ ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Amit Cohen authored
Check configurations and packets transference with different variations of autoneg and speed. Test plan: 1. Test force of same speed with autoneg off 2. Test force of different speeds with autoneg off (should fail) 3. One side is autoneg on and other side sets force of common speeds 4. One side is autoneg on and other side only advertises a subset of the common speeds (one speed of the subset) 5. One side is autoneg on and other side only advertises a subset of the common speeds. Check that highest speed is negotiated 6. Test autoneg on, but each side advertises different speeds (should fail) Signed-off-by: Amit Cohen <amitc@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Amit Cohen authored
Add a function that waits for device with maximum number of iterations. It enables to limit the waiting and prevent infinite loop. This will be used by the subsequent patch which will set two ports to different speeds in order to make sure they cannot negotiate a link. Waiting for all the setup is limited with 10 minutes for each device. Signed-off-by: Amit Cohen <amitc@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Amit Cohen authored
Functions: 1. speeds_arr_get The function returns an array of speed values from /usr/include/linux/ethtool.h The array looks as follows: [10baseT/Half] = 0, [10baseT/Full] = 1, ... 2. ethtool_set: params: cmd The function runs ethtool by cmd (ethtool -s cmd) and checks if there was an error in configuration 3. dev_speeds_get: params: dev, with_mode (0 or 1), adver (0 or 1) return value: Array of supported/Advertised link modes with/without mode * Example 1: speeds_get swp1 0 0 return: 1000 10000 40000 * Example 2: speeds_get swp1 1 1 return: 1000baseKX/Full 10000baseKR/Full 40000baseCR4/Full 4. common_speeds_get: params: dev1, dev2, with_mode (0 or 1), adver (0 or 1) return value: Array of common speeds of dev1 and dev2 * Example: common_speeds_get swp1 swp2 0 0 return: 1000 10000 Assuming that swp1 supports 1000 10000 40000 and swp2 supports 1000 10000 Signed-off-by: Amit Cohen <amitc@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Danielle Ratson authored
The scale test for Spectrum-2 should only be invoked for Spectrum-2. Skip the test otherwise. Signed-off-by: Danielle Ratson <danieller@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Danielle Ratson authored
Same as for Spectrum-1, test the ability to add the maximum number of routes possible to the switch. Invoke the test from the 'resource_scale' wrapper script. Signed-off-by: Danielle Ratson <danieller@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Jesper Dangaard says: ==================== page_pool: followup changes to restore tracepoint features This patchset is a followup to Jonathan patch, that do not release pool until inflight == 0. That changed page_pool to be responsible for its own delayed destruction instead of relying on xdp memory model. As the page_pool maintainer, I'm promoting the use of tracepoint to troubleshoot and help driver developers verify correctness when converting at driver to use page_pool. The role of xdp:mem_disconnect have changed, which broke my bpftrace tools for shutdown verification. With these changes, the same capabilities are regained. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jesper Dangaard Brouer authored
The MM tracepoint for page free (called kmem:mm_page_free) doesn't provide the page pointer directly, instead it provides the PFN (Page Frame Number). This is annoying when writing a page_pool leak detector in BPF. This patch change page_pool tracepoints to also provide the PFN. The page pointer is still provided to allow other kinds of troubleshooting from BPF. Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jesper Dangaard Brouer authored
When Jonathan change the page_pool to become responsible to its own shutdown via deferred work queue, then the disconnect_cnt counter was removed from xdp memory model tracepoint. This patch change the page_pool_inflight tracepoint name to page_pool_release, because it reflects the new responsability better. And it reintroduces a counter that reflect the number of times page_pool_release have been tried. The counter is also used by the code, to only empty the alloc cache once. With a stuck work queue running every second and counter being 64-bit, it will overrun in approx 584 billion years. For comparison, Earth lifetime expectancy is 7.5 billion years, before the Sun will engulf, and destroy, the Earth. Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jesper Dangaard Brouer authored
When looking at the details I realised that the memory poison in __xdp_mem_allocator_rcu_free doesn't make sense. This is because the SLUB allocator uses the first 16 bytes (on 64 bit), for its freelist, which overlap with members in struct xdp_mem_allocator, that were updated. Thus, SLUB already does the "poisoning" for us. I still believe that poisoning memory make sense in other cases. Kernel have gained different use-after-free detection mechanism, but enabling those is associated with a huge overhead. Experience is that debugging facilities can change the timing so much, that that a race condition will not be provoked when enabled. Thus, I'm still in favour of poisoning memory where it makes sense. Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Russell King authored
We currently match clause 45 PHYs using any ID read from a MMD marked as present in the "Devices in package" registers 5 and 6. However, this is incorrect. 45.2 says: "The definition of the term package is vendor specific and could be a chip, module, or other similar entity." so a package could be more or less than the whole PHY - a PHY could be made up of several modules instantiated onto a single chip such as the Marvell 88x3310, or some of the MMDs could be disabled according to chip configuration, such as the Broadcom 84881. In the case of Broadcom 84881, the "Devices in package" registers contain 0xc000009b, meaning that there is a PHYXS present in the package, but all registers in MMD 4 return 0xffff. This leads to our matching code incorrectly binding this PHY to one of our generic PHY drivers. This patch changes the way we determine whether to attempt to match a MMD identifier, or use it to request a module - if the identifier is all-ones, then we skip over it. When reading the identifiers, we initialise phydev->c45_ids.device_ids to all-ones, only reading the device ID if the "Devices in package" registers indicates we should. This avoids the generic drivers incorrectly matching on a PHY ID of 0xffffffff. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Russell King says: ==================== Add support for SFPs behind PHYs This series adds partial support for SFP cages connected to PHYs, specifically optical SFPs. We add core infrastructure to phylib for this, and arrange for minimal code in the PHY driver - currently, this is code to verify that the module is one that we can support for Marvell 10G PHYs. v2: add yaml binding patch ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Russell King authored
Add support for SFP+ cages to the Marvell 10G PHY driver. This is slightly complicated by the way phylib works in that we need to use a multi-step process to attach the SFP bus, and we also need to track the phylink state machine to know when the module's transmit disable signal should change state. With appropriate DT changes, this allows the SFP+ canges on the Macchiatobin platform to be functional. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Russell King authored
Add core phylib help for supporting SFP sockets on PHYs. This provides a mechanism to inform the SFP layer about PHY up/down events, and also unregister the SFP bus when the PHY is going away. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Russell King authored
Document the missing sfp property for ethernet controllers (which has existed for some time) which is being extended to ethernet PHYs. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-nextDavid S. Miller authored
Pablo Neira Ayuso says: ==================== Netfilter updates for net-next The following patchset contains Netfilter updates for net-next: 1) Wildcard support for the net,iface set from Kristian Evensen. 2) Offload support for matching on the input interface. 3) Simplify matching on vlan header fields. 4) Add nft_payload_rebuild_vlan_hdr() function to rebuild the vlan header from the vlan sk_buff metadata. 5) Pass extack to nft_flow_cls_offload_setup(). 6) Add C-VLAN matching support. 7) Use time64_t in xt_time to fix y2038 overflow, from Arnd Bergmann. 8) Use time_t in nft_meta to fix y2038 overflow, also from Arnd. 9) Add flow_action_entry_next() helper function to flowtable offload infrastructure. 10) Add IPv6 support to the flowtable offload infrastructure. 11) Support for input interface matching from postrouting, from Phil Sutter. 12) Missing check for ndo callback in flowtable offload, from wenxu. 13) Remove conntrack parameter from flow_offload_fill_dir(), from wenxu. 14) Do not pass flow_rule object for rule removal, cookie is sufficient to achieve this. 15) Release flow_rule object in case of error from the offload commit path. 16) Undo offload ruleset updates if transaction fails. 17) Check for error when binding flowtable callbacks, from wenxu. 18) Always unbind flowtable callbacks when unregistering hooks. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-