Remove the __exit mark from cifs_exit_dns_resolver() as it's called by the
module init routine in case of error, and so may have been discarded during
linkage.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] etr: fix clock synchronization race
  [S390] Fix IRQ tracing in case of PER

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  watchdog: update MAINTAINERS entry

* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Add a PC-beep workaround for ASUS P5-V
  ALSA: hda - Assume PC-beep as default for Realtek
  ALSA: hda - Don't register beep input device when no beep is available
  ALSA: hda - Fix pin-detection of Nvidia HDMI

Fix __task_cred()'s lockdep check by removing the following validation
condition:

	lockdep_tasklist_lock_is_held()

as commit_creds() does not take the tasklist_lock, and nor do most of the
functions that call it, so this check is pointless and it can prevent
detection of the RCU lock not being held if the tasklist_lock is held.

Instead, add the following validation condition:

	task->exit_state >= 0

to permit the access if the target task is dead and therefore unable to change
its own credentials.

Fix __task_cred()'s comment to:

 (1) discard the bit that says that the caller must prevent the target task
     from being deleted.  That shouldn't need saying.

 (2) Add a comment indicating the result of __task_cred() should not be passed
     directly to get_cred(), but rather than get_task_cred() should be used
     instead.

Also put a note into the documentation to enforce this point there too.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It's possible for get_task_cred() as it currently stands to 'corrupt' a set of
credentials by incrementing their usage count after their replacement by the
task being accessed.

What happens is that get_task_cred() can race with commit_creds():

	TASK_1			TASK_2			RCU_CLEANER
	-->get_task_cred(TASK_2)
	rcu_read_lock()
	__cred = __task_cred(TASK_2)
				-->commit_creds()
				old_cred = TASK_2->real_cred
				TASK_2->real_cred = ...
				put_cred(old_cred)
				  call_rcu(old_cred)
		[__cred->usage == 0]
	get_cred(__cred)
		[__cred->usage == 1]
	rcu_read_unlock()
							-->put_cred_rcu()
							[__cred->usage == 1]
							panic()

However, since a tasks credentials are generally not changed very often, we can
reasonably make use of a loop involving reading the creds pointer and using
atomic_inc_not_zero() to attempt to increment it if it hasn't already hit zero.

If successful, we can safely return the credentials in the knowledge that, even
if the task we're accessing has released them, they haven't gone to the RCU
cleanup code.

We then change task_state() in procfs to use get_task_cred() rather than
calling get_cred() on the result of __task_cred(), as that suffers from the
same problem.

Without this change, a BUG_ON in __put_cred() or in put_cred_rcu() can be
tripped when it is noticed that the usage count is not zero as it ought to be,
for example:

kernel BUG at kernel/cred.c:168!
invalid opcode: 0000 [#1] SMP
last sysfs file: /sys/kernel/mm/ksm/run
CPU 0
Pid: 2436, comm: master Not tainted 2.6.33.3-85.fc13.x86_64 #1 0HR330/OptiPlex
745
RIP: 0010:[<ffffffff81069881>]  [<ffffffff81069881>] __put_cred+0xc/0x45
RSP: 0018:ffff88019e7e9eb8  EFLAGS: 00010202
RAX: 0000000000000001 RBX: ffff880161514480 RCX: 00000000ffffffff
RDX: 00000000ffffffff RSI: ffff880140c690c0 RDI: ffff880140c690c0
RBP: ffff88019e7e9eb8 R08: 00000000000000d0 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000040 R12: ffff880140c690c0
R13: ffff88019e77aea0 R14: 00007fff336b0a5c R15: 0000000000000001
FS:  00007f12f50d97c0(0000) GS:ffff880007400000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f8f461bc000 CR3: 00000001b26ce000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process master (pid: 2436, threadinfo ffff88019e7e8000, task ffff88019e77aea0)
Stack:
 ffff88019e7e9ec8 ffffffff810698cd ffff88019e7e9ef8 ffffffff81069b45
<0> ffff880161514180 ffff880161514480 ffff880161514180 0000000000000000
<0> ffff88019e7e9f28 ffffffff8106aace 0000000000000001 0000000000000246
Call Trace:
 [<ffffffff810698cd>] put_cred+0x13/0x15
 [<ffffffff81069b45>] commit_creds+0x16b/0x175
 [<ffffffff8106aace>] set_current_groups+0x47/0x4e
 [<ffffffff8106ac89>] sys_setgroups+0xf6/0x105
 [<ffffffff81009b02>] system_call_fastpath+0x16/0x1b
Code: 48 8d 71 ff e8 7e 4e 15 00 85 c0 78 0b 8b 75 ec 48 89 df e8 ef 4a 15 00
48 83 c4 18 5b c9 c3 55 8b 07 8b 07 48 89 e5 85 c0 74 04 <0f> 0b eb fe 65 48 8b
04 25 00 cc 00 00 48 3b b8 58 04 00 00 75
RIP  [<ffffffff81069881>] __put_cred+0xc/0x45
 RSP <ffff88019e7e9eb8>
---[ end trace df391256a100ebdd ]---
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add Mailing-list and website to watchdog MAINTAINERS entry.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

ASUS P5-V provides a SSID that unexpectedly matches with the value
compilant with Realtek's specification.  Thus the driver interprets
it badly, resulting in non-working PC beep.

This patch adds a white-list for such a case; a white-list of known
devices with working PC beep.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
  x86,kgdb: Fix hw breakpoint regression

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] ibmvscsi: Fix oops when an interrupt is pending during probe
  [SCSI] zfcp: Update status read mempool
  [SCSI] zfcp: Do not wait for SBALs on stopped queue
  [SCSI] zfcp: Fix check whether unchained ct_els is possible
  [SCSI] ipr: fix resource path display and formatting

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  davinci: da850/omap-l138 evm: account for DEFDCDC{2,3} being tied high
  regulator: tps6507x: allow driver to use DEFDCDC{2,3}_HIGH register
  wm8350-regulator: fix wm8350_register_regulator error handling
  ab3100: fix off-by-one value range checking for voltage selector

The function ecryptfs_uid_hash wrongly assumes that the
second parameter to hash_long() is the number of hash
buckets instead of the number of hash bits.
This patch fixes that and renames the variable
ecryptfs_hash_buckets to ecryptfs_hash_bits to make it
clearer.

Fixes: CVE-2010-2492
Signed-off-by: Andre Osterhues <aosterhues@escrypt.com>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

HW breakpoints events stopped working correctly with kgdb
as a result of commit: 018cbffe
(Merge commit 'v2.6.33' into perf/core).

The regression occurred because the behavior changed for setting
NOTIFY_STOP as the return value to the die notifier if the breakpoint
was known to the HW breakpoint API.  Because kgdb is using the HW
breakpoint API to register HW breakpoints slots, it must also now
implement the overflow_handler call back else kgdb does not get to see
the events from the die notifier.

The kgdb_ll_trap function will be changed to be general purpose code
which can allow an easy way to implement the hw_breakpoint API
overflow call back.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Dongdong Deng <dongdong.deng@windriver.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  ceph: use complete_all and wake_up_all
  ceph: Correct obvious typo of Kconfig variable "CRYPTO_AES"
  ceph: fix dentry lease release
  ceph: fix leak of dentry in ceph_init_dentry() error path
  ceph: fix pg_mapping leak on pg_temp updates
  ceph: fix d_release dop for snapdir, snapped dentries
  ceph: avoid dcache readdir for snapdir

If we don't need a huge amount of memory in ->readdir() then
we can use kmalloc rather than vmalloc to allocate it. This
should cut down on the greater overheads associated with
vmalloc for smaller directories.

We may be able to eliminate vmalloc entirely at some stage,
but this is easy to do right away.

Also using GFP_NOFS to avoid any issues wrt to deleting inodes
while under a glock, and suggestion from Linus to factor out
the alloc/dealloc.

I've given this a test with a variety of different sized
directories and it seems to work ok.

Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Enable PC-beep as default for hardwares that aren't compliant with the
SSID value Realtek requires.  In such a case, better to enable the beep
to avoid a regression.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

We check now the availability of PC beep and skip the build of beep
mixers, but the driver still registers the input device.  This should
be checked as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Per the da850/omap-l138 Beta EVM SOM schematic, the DEFDCDC2 and
DEFDCDC3 lines are tied high. This leads to a 3.3V IO and 1.2V CVDD
voltage.

Pass the right platform data to the TPS6507x driver so it can operate
on the DEFDCDC{2,3}_HIGH register to read and change voltage levels.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

In TPS6507x, depending on the status of DEFDCDC{2,3} pin either
DEFDCDC{2,3}_LOW or DEFDCDC{2,3}_HIGH register needs to be read or
programmed to change the output voltage.

The current driver assumes DEFDCDC{2,3} pins are always tied low
and thus operates only on DEFDCDC{2,3}_LOW register. This need
not always be the case (as is found on OMAP-L138 EVM).

Unfortunately, software cannot read the status of DEFDCDC{2,3} pins.
So, this information is passed through platform data depending on
how the board is wired.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

The behavior of Nvidia HDMI codec regarding the pin-detection unsol events
is based on the old HD-audio spec, i.e. PD bit indicates only the update
and doesn't show the current state.  Since the current code assumes the
new behavior, the pin-detection doesn't work relialby with these h/w.

This patch adds a flag for indicating the old spec, and fixes the issue
by checking the pin-detection explicitly for such hardware.
Tested-by: Wei Ni <wni@nvidia.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  9p: Pass the correct end of buffer to p9stat_read

When freeing a gpio that has not been exported, gpio_unexport() prints a
debug message when it should just fall through silently.

Example spurious message:

	gpio_unexport: gpio0 status -22
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Uwe Kleine-K?nig <u.kleine-koenig@pengutronix.de>
Cc: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The MPC85xx EDAC driver is missing module device aliases, so the driver
won't load automatically on boot.  This patch fixes the issue by adding
proper MODULE_DEVICE_TABLE() macros.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Dave Jiang <djiang@mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix the logic while writing new date/time to the chip.  The driver
incorrectly wrote back register values to different registers and even
with wrong mask.  The patch adds clearing of the VLF register, which
should be cleared if all date/time values are set.
Signed-off-by: Rudolf Marek <rudolf.marek@sysgo.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Martyn Welch <martyn.welch@gefanuc.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The command

	echo "file ec.c +p" >/sys/kernel/debug/dynamic_debug/control

causes an oops.

Move the call to ddebug_remove_module() down into free_module().  In this
way it should be called from all error paths.  Currently, we are missing
the remove if the module init routine fails.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Reported-by: Thomas Renninger <trenn@suse.de>
Tested-by: Thomas Renninger <trenn@suse.de>
Cc: <stable@kernel.org>		[2.6.32+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This fixes an issue triggered by running concurrent syncs. One of the syncs
would go through while the other would just hang indefinitely. In any case, we
never actually want to wake a single waiter, so the *_all functions should
be used.
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>

Pass the correct end of the buffer to p9stat_read.
Signed-off-by: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>

The etr events switch-to-local and sync-check disable the synchronous clock
and schedule a work queue that tries to get the clock back into sync.
If another switch-to-local or sync-check event occurs while the work queue
function etr_work_fn still runs the eacr.es bit and the clock_sync_word can
become inconsistent because check_sync_clock only uses the clock_sync_word
to determine if the clock is in sync or not. The second pass of the
etr_work_fn will reset the eacr.es bit but will leave the clock_sync_word
intact. Fix this race by moving the reset of the eacr.es bit into the
switch-to-local and sync-check functions and by checking the eacr.es bit
as well to decide if the clock needs to be synced.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

In case user space is single stepped (PER) the program check handler
claims too early that IRQs are enabled on the return path.
Subsequent checks will notice that the IRQ mask in the PSW and
what lockdep thinks the IRQ mask should be do not correlate and
therefore will print a warning to the console and disable lockdep.

Fix this by doing all the work within the correct context.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

A driver needs to be ready to take an interrupt as soon as it registers
an interrupt handler. I noticed the following oops when testing kdump:

ipr: IBM Power RAID SCSI Device Driver version: 2.5.0 (February 11, 2010)
ibmvscsi 30000002: SRP_VERSION: 16.a
ibmvscsi 30000002: SRP_VERSION: 16.a
Unable to handle kernel paging request for data at address 0x00000000
...
pc: c000000004085e34: .tasklet_action+0xf4/0x1dc
...
c000000004086fe4 .__do_softirq+0x16c/0x2c0
c00000000403138c .call_do_softirq+0x14/0x24
c00000000400ee14 .do_softirq+0xa0/0x104
c00000000408690c .irq_exit+0x70/0xd0
c00000000400f190 .do_IRQ+0x214/0x2a8
c000000004004804 hardware_interrupt_entry+0x1c/0x98
--- Exception: 501 (Hardware Interrupt) at c00000000400c544 .raw_local_irq_restore+0x48/0x54
c00000000465d2a8 ._raw_spin_unlock_irqrestore+0x74/0xa0
c0000000040e7f00 .__setup_irq+0x2ec/0x3f0
c0000000040e8198 .request_threaded_irq+0x194/0x22c
c00000000446d854 .rpavscsi_init_crq_queue+0x284/0x3f0
c00000000446c764 .ibmvscsi_probe+0x688/0x710
c00000000402903c .vio_bus_probe+0x37c/0x3e4
c000000004403f10 .driver_probe_device+0xec/0x1b8
c000000004404088 .__driver_attach+0xac/0xf4
c000000004403184 .bus_for_each_dev+0x98/0x104
c000000004403c98 .driver_attach+0x40/0x60
c0000000044026f0 .bus_add_driver+0x154/0x324
c0000000044045d0 .driver_register+0xe8/0x1ac
c00000000402b2a8 .vio_register_driver+0x54/0x74
c000000004933ea4 .ibmvscsi_module_init+0x80/0xc0
c000000004009834 .do_one_initcall+0x98/0x1d8
c0000000049005b4 .kernel_init+0x27c/0x33c
c000000004031550 .kernel_thread+0x54/0x70

srp_task needs to be setup before request_irq. The patch below fixes the oops.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/perf:
  perf, powerpc: Use perf_sample_data_init() for the FSL code

* git://git.infradead.org/users/cbou/battery-2.6.35:
  ds2782_battery: Rename get_current to fix build failure / name conflict

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  s2io: fixing DBG_PRINT() macro
  ath9k: fix dma direction for map/unmap in ath_rx_tasklet
  net: dev_forward_skb should call nf_reset
  net sched: fix race in mirred device removal
  tun: avoid BUG, dump packet on GSO errors
  bonding: set device in RLB ARP packet handler
  wimax/i2400m: Add PID & VID for Intel WiMAX 6250
  ipv6: Don't add routes to ipv6 disabled interfaces.
  net: Fix skb_copy_expand() handling of ->csum_start
  net: Fix corruption of skb csum field in pskb_expand_head() of net/core/skbuff.c
  macvtap: Limit packet queue length
  ixgbe/igb: catch invalid VF settings
  bnx2x: Advance a module version
  bnx2x: Protect statistics ramrod and sequence number
  bnx2x: Protect a SM state change
  wireless: use netif_rx_ni in ieee80211_send_layer2_update

We should use perf_sample_data_init() to initialize struct
perf_sample_data.  As explained in the description of commit dc1d628a
("perf: Provide generic perf_sample_data initialization"), it is
possible for userspace to get the kernel to dereference data.raw,
so if it is not initialized, that means that unprivileged userspace
can possibly oops the kernel.  Using perf_sample_data_init makes sure
it gets initialized to NULL.

This conversion should have been included in commit dc1d628a, but it
got missed.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

In the case of platform_device_add() fail, we should call
platform_device_put() instead of platform_device_del()
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

We use voltage selector as an array index for typ_voltages.
Thus the valid range for voltage selector should be 0..voltages_len-1.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Do not try to disable hpet if it hasn't been initialized before
  x86, i8259: Only register sysdev if we have a real 8259 PIC

Patch 9e39f7c5 changed the
DBG_PRINT() macro and the if clause was wrongly changed. It means
that currently all the DBG_PRINT are being printed, flooding the
kernel log buffer with things like:

s2io: eth6: Next block at: c0000000b9c90000
s2io: eth6: In Neterion Tx routine
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Sreenivasa Honnur <Sreenivasa.Honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] powernow-k8: Limit Pstate transition latency check
  [CPUFREQ] Fix PCC driver error path
  [CPUFREQ] fix double freeing in error path of pcc-cpufreq
  [CPUFREQ] pcc driver should check for pcch method before calling _OSC
  [CPUFREQ] fix memory leak in cpufreq_add_dev
  [CPUFREQ] revert "[CPUFREQ] remove rwsem lock from CPUFREQ_GOV_STOP call (second call site)"

* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Set io_map_base for several PCI bridges lacking it
  MIPS: Alchemy: Define eth platform devices in the correct order
  MIPS: BCM63xx: Prevent second enet registration on BCM6338
  MIPS: Quit using undefined behavior of ADDU in 64-bit atomic operations.
  MIPS: N32: Define getdents64.
  MIPS: MTX-1: Fix PCI on the MeshCube and related boards
  MIPS: Make init_vdso a subsys_initcall.
  MIPS: "Fix" useless 'init_vdso successfully' message.
  MIPS: PowerTV: Move register setup to before reading registers.
  SOUND: Au1000: Fix section mismatch
  VIDEO: Au1100fb: Fix section mismatch
  VIDEO: PMAGB-B: Fix section mismatch
  VIDEO: PMAG-BA: Fix section mismatch
  NET: declance: Fix section mismatches
  VIDEO. gbefb: Fix section mismatches.