In the edma_free_cont_slots API, the variable slot was being modified
and then used in the for loop.
This results in incorrect behaviour when the API is used.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

On the latest DA850/OMAP-L138 EVM (Beta) the GPIO pin
number of LCD panel power has changed. This patch takes
care of this change. Software will support only Beta
versions of DA850/OMAP-L138 EVM.

In the process, add the missing entry for data pin 0
and remove the GPIO specific pins from da850_lcdcntl_pins
structure. EVM specific muxing for LCD is being done in the
board file now.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Add RTC support for the da830/omap-l137 and da850/omap-l138
SoC's by leveraging existing the rtc-omap driver.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Add graphics support for the Sharp LCD035Q3DG01 graphical
LCD that's on the User Interface (UI) daughter card of the
DA830/OMAP-L137 EVM.

The LCD shares EMIFA lines with the NAND and NOR devices that
are also on the UI card so those lines are shared via a couple
of muxes.  The muxes are controlled by the 'MUX_MODE' line on
the UI card.  The 'MUX_MODE' line is controlled by pin P6 of
a pcf8574 i2c expander that's at i2c address 0x3f on UI card.
The i2c expander is controlled using the gpio infrastructure
from the board code using the 'setup()' and 'teardown()'
routines.
Signed-off-by: Steve Chen <schen@mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Add support for the Sharp LCD035Q3DG01 graphical LCD.  This
requires a minor interface change to da8xx_register_lcdc()
so that the board code can pass in the platform_data which
describes the lcd controller that's to be used.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Add pinmux settings, etc. to enable the MMC/SC hardware.
Signed-off-by: David A. Griego <dgriego@mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

DM6467 silicon revisions 3.x have variant field in JTAGID register as '1'.
This path adds entry for the same in dm646x_ids to be able to boot on boards
with 3.x revision chips.

Also modifies name for 'variant=0' (revisions 1.0, 1.1).
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

The patch allows Async3 clock source to be selected between PLL1 SYSCLK2
and PLL0 SYSCLK2.

Having Async3 source from PLL1 SYSCLK2 allows peripherals on that
domain to remain unaffected by frequency scaling on PLL0.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

The clk_set_parent() API is implemented to enable re-parenting
clocks in the clock tree.

This is useful in DVFS and helps by shifting clocks to an asynchronous
domain where supported by hardware
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

clk_round_rate, clk_set_rate have been updated to handle dynamic
frequency changes.

The motivation behind the changes is to support dynamic CPU frequency
change.

davinci_set_pllrate() changes the PLL rate of a given PLL. This function
has been presented as a generic function though it has been tested only
on OMAP-L138 EVM. No other currently available DaVinci device will probably
use this function, but any future device specific changes will hopefully be
small enough to get taken care using a cpu_is_xxx() macro.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Make clock rate recalculation easy by having a re-calculate
function for each clock.

The existing functions for calculation of output rates of PLL
and PLL-derived sysclks have been convered to the new
re-calculate API.

A new function is introduced to take care of rate
(re)calculation for leaf clocks.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Achieve easy top down traversal of clock tree by keeping
track of each clock's list of children.

This is useful in supporting DVFS where clock rates of
all children need to be updated in an efficient manner.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

This makes it clear that JTAG ID register is part of the
SYSCFG module
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Avoid use of IO_ADDRESS() for SYSCFG module by doing an ioremap() instead.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Rename the DA8XX_BOOT_CFG_BASE macro to get it in line
with the public documentation for these parts.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

The DA830/OMAP-L137 EVM cannot use the default pinmux setup for McASP1
so put the correct settings in the board file for that platform.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

For consistency with existing code, change the name of
da8xx_init_mcasp() to da8xx_register_mcasp().
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Some mcasp code was inserted between the emac resource setup
and the related register routine that registers the emac.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

1) Registers the platform device for McBSP on dm365.
2) Add platform data to DM365 EVM board file.
3) Set i2c address for audio codec at DM365 EVM board file.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

The parent clock for the USB source clock is actually PLL1 aux clock,
not PLL2 sysclk1.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

This patch fixes a typo/bug in the DM365 SDIO interrupt assignment
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  SUNRPC: Address buffer overrun in rpc_uaddr2sockaddr()
  NFSv4: Fix a cache validation bug which causes getcwd() to return ENOENT

As this struct is exposed to user space and the API was added for this
release it's a bit of a pain for the C++ world and we still have time to
fix it. Rename the fields before we end up with that pain in an actual
release.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Olivier Goffart
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 86cf898e ("intel-iommu: Check for
'DMAR at zero' BIOS error earlier.") was supposed to work by pretending
not to detect an IOMMU if it was actually being reported by the BIOS at
physical address zero.

However, the intel_iommu_init() function is called unconditionally, as
are the corresponding functions for other IOMMU hardware.

So the patch only worked if you have RAM above the 4GiB boundary. It
caused swiotlb to be initialised when no IOMMU was detected during early
boot, and thus the later IOMMU init would refuse to run.

But if you have less RAM than that, swiotlb wouldn't get set up and the
IOMMU _would_ still end up being initialised, even though we never
claimed to detect it.

This patch also sets the dmar_disabled flag when the error is detected
during the initial detection phase -- so that the later call to
intel_iommu_init() will return without doing anything, regardless of
whether swiotlb is used or not.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] Fix stale cpufreq_cpu_governor pointer
  [CPUFREQ] Resolve time unit thinko in ondemand/conservative govs
  [CPUFREQ] speedstep-ich: fix error caused by 394122ab
  [CPUFREQ] Fix use after free on governor restore
  [CPUFREQ] acpi-cpufreq: blacklist Intel 0f68: Fix HT detection and put in notification message
  [CPUFREQ] powernow-k8: Fix test in get_transition_latency()
  [CPUFREQ] longhaul: select Longhaul version 2 for capable CPUs

Doing the strcmp return value as

	signed char __res = *cs - *ct;

is wrong for two reasons.  The subtraction can overflow because __res
doesn't use a type big enough.  Moreover the compared bytes should be
interpreted as unsigned char as specified by POSIX.

The same problem is fixed in strncmp.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'agp-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
  agp/intel-agp: Set dma_mask for capable chipsets before agp_add_bridge()

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  ima: replace GFP_KERNEL with GFP_NOFS

We should set this before calling agp_add_bridge() so that it's done
before we map the scratch page too.

This should probably fix the regression reported as k.o. bug #14627.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  OMAP: cs should be positive in gpmc_cs_free()
  omap: fix unlikely(x) < y
  omap3: clock: Fixed dpll3_m2x2 rate calculation
  omap3: clock: Fix the DPLL freqsel computations
  omap: Fix keymap for zoom2 according to matrix keypad framwork

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ASoC: tlv320aic23 fix rate selection
  ASoC: OMAP3 Pandora: update for TWL4030 codec changes
  ASoC: Modifying the license string GPLv2 for OMAP3 EVM
  ALSA: hda - Fix quirk for VAIO type G
  ALSA: usb - Quirk to disable master volume control in PCM2702

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
  cxgb3: fix premature page unmap
  ibm_newemac: Fix EMACx_TRTR[TRT] bit shifts
  vlan: Fix register_vlan_dev() error path
  gro: Fix illegal merging of trailer trash
  sungem: Fix Serdes detection.
  net: fix mdio section mismatch warning
  ppp: fix BUG on non-linear SKB (multilink receive)
  ixgbe: Fixing EEH handler to handle more than one error
  net: Fix the rollback test in dev_change_name()
  Revert "isdn: isdn_ppp: Use SKB list facilities instead of home-grown implementation."
  TI Davinci EMAC : Fix Console Hang when bringing the interface down
  smsc911x: Fix Console Hang when bringing the interface down.
  mISDN: fix error return in HFCmulti_init()
  forcedeth: mac address fix
  r6040: fix version printing
  Bluetooth: Fix regression with L2CAP configuration in Basic Mode
  Bluetooth: Select Basic Mode as default for SOCK_SEQPACKET
  Bluetooth: Set general bonding security for ACL by default
  r8169: Fix receive buffer length when MTU is between 1515 and 1536
  can: add the missing netlink get_xstats_size callback
  ...

While running fsstress tests on the NFSv4 mounted ext3 and ext4
filesystem, the following call trace was generated on the nfs
server machine.

Replace GFP_KERNEL with GFP_NOFS in ima_iint_insert() to avoid a
potential deadlock.

     =================================
    [ INFO: inconsistent lock state ]
    2.6.31-31.el6.x86_64 #1
    ---------------------------------
    inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage.
    kswapd2/75 [HC0[0]:SC0[0]:HE1:SE1] takes:
     (jbd2_handle){+.+.?.}, at: [<ffffffff811edd5e>] jbd2_journal_start+0xfe/0x13f
    {RECLAIM_FS-ON-W} state was registered at:
      [<ffffffff81091e40>] mark_held_locks+0x65/0x99
      [<ffffffff81091f31>] lockdep_trace_alloc+0xbd/0xf5
      [<ffffffff81126fdd>] kmem_cache_alloc+0x40/0x185
      [<ffffffff812344d7>] ima_iint_insert+0x3d/0xf1
      [<ffffffff812345b0>] ima_inode_alloc+0x25/0x44
      [<ffffffff811484ac>] inode_init_always+0xec/0x271
      [<ffffffff81148682>] alloc_inode+0x51/0xa1
      [<ffffffff81148700>] new_inode+0x2e/0x94
      [<ffffffff811b2f08>] ext4_new_inode+0xb8/0xdc9
      [<ffffffff811be611>] ext4_create+0xcf/0x175
      [<ffffffff8113e2cd>] vfs_create+0x82/0xb8
      [<ffffffff8113f337>] do_filp_open+0x32c/0x9ee
      [<ffffffff811309b9>] do_sys_open+0x6c/0x12c
      [<ffffffff81130adc>] sys_open+0x2e/0x44
      [<ffffffff81011e42>] system_call_fastpath+0x16/0x1b
      [<ffffffffffffffff>] 0xffffffffffffffff
    irq event stamp: 90371
    hardirqs last  enabled at (90371): [<ffffffff8112708d>]
    kmem_cache_alloc+0xf0/0x185
    hardirqs last disabled at (90370): [<ffffffff81127026>]
    kmem_cache_alloc+0x89/0x185
    softirqs last  enabled at (89492): [<ffffffff81068ecf>]
    __do_softirq+0x1bf/0x1eb
    softirqs last disabled at (89477): [<ffffffff8101312c>] call_softirq+0x1c/0x30

    other info that might help us debug this:
    2 locks held by kswapd2/75:
     #0:  (shrinker_rwsem){++++..}, at: [<ffffffff810f98ba>] shrink_slab+0x44/0x177
     #1:  (&type->s_umount_key#25){++++..}, at: [<ffffffff811450ba>]
Reported-by: Muni P. Beerakam <mbeeraka@in.ibm.com>
Reported-by: Amit K. Arora <amitarora@in.ibm.com>
Cc: stable@kernel.org
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>

The index `cs' is signed, test whether it is negative before we release
gpmc_cs_mem[cs].
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

The closing parenthesis was not in the right location.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

* 'sh/for-2.6.32' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: Fixup last users of irq_chip->typename
  uio: pm_runtime_disable is needed if failed

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: option.c: add support for D-Link DWM-162-U5
  USB: usbmon: fix bug in mon_buff_area_shrink
  USB: xhci: Fix scratchpad deallocation.
  USB: xhci: Fix TRB physical to virtual address translation.
  USB: xhci: Fix bug memory free after failed initialization.
  USB: cdc_acm: Fix memory leak after hangup
  USB: cdc_acm: Fix race condition when opening tty
  USB: ohci: quirk AMD prefetch for USB 1.1 ISO transfer