Pull late ARM updates from Russell King:
 "Here is the late set of ARM updates for this merge window; in here is:

   - The ARM parts of the broadcast timer support, core parts merged
     through tglx's tree.  This was left over from the previous merge to
     allow the dependency on tglx's tree to be resolved.

   - A fix to the VFP code which shows up on Raspberry Pi's, as well as
     fixing the fallout from a previous commit in this area.

   - A number of smaller fixes scattered throughout the ARM tree"

* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: Fix broken commit 0cc41e4a corrupting kernel messages
  ARM: fix scheduling while atomic warning in alignment handling code
  ARM: VFP: fix emulation of second VFP instruction
  ARM: 7656/1: uImage: Error out on build of multiplatform without LOADADDR
  ARM: 7640/1: memory: tegra_ahb_enable_smmu() depends on TEGRA_IOMMU_SMMU
  ARM: 7654/1: Preserve L_PTE_VALID in pte_modify()
  ARM: 7653/2: do not scale loops_per_jiffy when using a constant delay clock
  ARM: 7651/1: remove unused smp_timer_broadcast #define

Pull char/misc patch from Greg Kroah-Hartman:
 "Here is one remaining patch for 3.9-rc1.  It is for the hyper-v
  drivers, and had to wait until some other patches went in through the
  x86 tree."
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Drivers: hv: vmbus: Use the new infrastructure for delivering VMBUS interrupts

Pull USB patch revert from Greg Kroah-Hartman:
 "Here is one remaining USB patch for 3.9-rc1, it reverts a 3.8 patch
  that has caused a lot of regressions for some VIA EHCI controllers."

* tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: EHCI: revert "remove ASS/PSS polling timeout"

Pull watchdog updates from Wim Van Sebroeck:
 "This contains:
   - fixes and improvements
   - devicetree bindings
   - conversion to watchdog generic framework of the following drivers:
        - booke_wdt
        - bcm47xx_wdt.c
        - at91sam9_wdt
   - Removal of old STMP3xxx driver
   - Addition of following new drivers:
        - new driver for STMP3xxx and i.MX23/28
        - Retu watchdog driver"

* git://www.linux-watchdog.org/linux-watchdog: (30 commits)
  watchdog: sp805_wdt depends on ARM
  watchdog: davinci_wdt: update to devm_* API
  watchdog: davinci_wdt: use devm managed clk get
  watchdog: at91rm9200: add DT support
  watchdog: add timeout-sec property binding
  watchdog: at91sam9_wdt: Convert to use the watchdog framework
  watchdog: omap_wdt: Add option nowayout
  watchdog: core: dt: add support for the timeout-sec dt property
  watchdog: bcm47xx_wdt.c: add hard timer
  watchdog: bcm47xx_wdt.c: rename wdt_time to timeout
  watchdog: bcm47xx_wdt.c: rename ops methods
  watchdog: bcm47xx_wdt.c: use platform device
  watchdog: bcm47xx_wdt.c: convert to watchdog core api
  watchdog: Convert BookE watchdog driver to watchdog infrastructure
  watchdog: s3c2410_wdt: Use devm_* functions
  watchdog: remove old STMP3xxx driver
  watchdog: add new driver for STMP3xxx and i.MX23/28
  rtc: stmp3xxx: add wdt-accessor function
  watchdog: introduce retu_wdt driver
  watchdog: intel_scu_watchdog: fix Kconfig dependency
  ...

Pull second set of slave-dmaengine updates from Vinod Koul:
 "Arnd's patch moves the dw_dmac to use generic DMA binding.  I agreed
  to merge this late as it will avoid the conflicts between trees.

  The second patch from Matt adding a dma_request_slave_channel_compat
  API was supposed to be picked up, but somehow never got picked up.
  Some patches dependent on this are already in -next :("

* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: dw_dmac: move to generic DMA binding
  dmaengine: add dma_request_slave_channel_compat()

Pull x86 platform driver updates from Matthew Garrett:
 "Mostly relatively small updates, along with some hardware enablement
  for Sony hardware and a pile of updates to Google's Chromebook driver"

* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (49 commits)
  ideapad-laptop: Depend on BACKLIGHT_CLASS_DEVICE instead of selecting it
  ideapad: depends on backlight subsystem and update comment
  Platform: x86: chromeos_laptop - add i915 gmbuses to adapter names
  Platform: x86: chromeos_laptop - Add isl light sensor for Pixel
  Platform: x86: chromeos_laptop - Add a more general add_i2c_device
  Platform: x86: chromeos_laptop - Add Pixel Touchscreen
  Platform: x86: chromeos_laptop - Add support for probing devices
  Platform: x86: chromeos_laptop - Add Pixel Trackpad
  hp-wmi: fix handling of platform device
  sony-laptop: leak in error handling sony_nc_lid_resume_setup()
  hp-wmi: Add support for SMBus hotkeys
  asus-wmi: Fix unused function build warning
  acer-wmi: avoid the warning of 'devices' may be used uninitialized
  drivers/platform/x86/thinkpad_acpi.c: Handle HKEY event 0x6040
  Platform: x86: chromeos_laptop - Add HP Pavilion 14
  Platform: x86: chromeos_laptop - Add Taos tsl2583 device
  Platform: x86: chromeos_laptop - Add Taos tsl2563 device
  Platform: x86: chromeos_laptop - Add Acer C7 trackpad
  Platform: x86: chromeos_laptop - Rename setup_lumpy_tp to setup_cyapa_smbus_tp
  asus-laptop: always report brightness key events
  ...

Pull ext4 bug fixes from Ted Ts'o:
 "Various bug fixes for ext4.  The most important is a fix for the new
  extent cache's slab shrinker which can cause significant, user-visible
  pauses when the system is under memory pressure."

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: enable quotas before orphan cleanup
  ext4: don't allow quota mount options when quota feature enabled
  ext4: fix a warning from sparse check for ext4_dir_llseek
  ext4: convert number of blocks to clusters properly
  ext4: fix possible memory leak in ext4_remount()
  jbd2: fix ERR_PTR dereference in jbd2__journal_start
  ext4: use percpu counter for extent cache count
  ext4: optimize ext4_es_shrink()

Pull sigprocmask compat fix from Al Viro:
 "generic compat_sys_rt_sigprocmask() had a very dumb braino; I'd spent
  quite a while staring at the offending commit before finally managing
  to spot the idiocy ;-/"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
  fix compat_sys_rt_sigprocmask()

Converting bitmask to 32bit granularity is fine, but we'd better
_do_ something with the result.  Such as "copy it to userland"...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull NFS client bugfixes from Trond Myklebust:
 "We've just concluded another Connectathon interoperability testing
  week, and so here are the fixes for the bugs that were discovered:

   - Don't allow NFS silly-renamed files to be deleted
   - Don't start the retransmission timer when out of socket space
   - Fix a couple of pnfs-related Oopses.
   - Fix one more NFSv4 state recovery deadlock
   - Don't loop forever when LAYOUTGET returns NFS4ERR_LAYOUTTRYLATER"

* tag 'nfs-for-3.9-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  SUNRPC: One line comment fix
  NFSv4.1: LAYOUTGET EDELAY loops timeout to the MDS
  SUNRPC: add call to get configured timeout
  PNFS: set the default DS timeout to 60 seconds
  NFSv4: Fix another open/open_recovery deadlock
  nfs: don't allow nfs_find_actor to match inodes of the wrong type
  NFSv4.1: Hold reference to layout hdr in layoutget
  pnfs: fix resend_to_mds for directio
  SUNRPC: Don't start the retransmission timer when out of socket space
  NFS: Don't allow NFS silly-renamed files to be deleted, no signal

Pull btrfs update from Chris Mason:
 "The biggest feature in the pull is the new (and still experimental)
  raid56 code that David Woodhouse started long ago.  I'm still working
  on the parity logging setup that will avoid inconsistent parity after
  a crash, so this is only for testing right now.  But, I'd really like
  to get it out to a broader audience to hammer out any performance
  issues or other problems.

  scrub does not yet correct errors on raid5/6 either.

  Josef has another pass at fsync performance.  The big change here is
  to combine waiting for metadata with waiting for data, which is a big
  latency win.  It is also step one toward using atomics from the
  hardware during a commit.

  Mark Fasheh has a new way to use btrfs send/receive to send only the
  metadata changes.  SUSE is using this to make snapper more efficient
  at finding changes between snapshosts.

  Snapshot-aware defrag is also included.

  Otherwise we have a large number of fixes and cleanups.  Eric Sandeen
  wins the award for removing the most lines, and I'm hoping we steal
  this idea from XFS over and over again."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (118 commits)
  btrfs: fixup/remove module.h usage as required
  Btrfs: delete inline extents when we find them during logging
  btrfs: try harder to allocate raid56 stripe cache
  Btrfs: cleanup to make the function btrfs_delalloc_reserve_metadata more logic
  Btrfs: don't call btrfs_qgroup_free if just btrfs_qgroup_reserve fails
  Btrfs: remove reduplicate check about root in the function btrfs_clean_quota_tree
  Btrfs: return ENOMEM rather than use BUG_ON when btrfs_alloc_path fails
  Btrfs: fix missing deleted items in btrfs_clean_quota_tree
  btrfs: use only inline_pages from extent buffer
  Btrfs: fix wrong reserved space when deleting a snapshot/subvolume
  Btrfs: fix wrong reserved space in qgroup during snap/subv creation
  Btrfs: remove unnecessary dget_parent/dput when creating the pending snapshot
  btrfs: remove a printk from scan_one_device
  Btrfs: fix NULL pointer after aborting a transaction
  Btrfs: fix memory leak of log roots
  Btrfs: copy everything if we've created an inline extent
  btrfs: cleanup for open-coded alignment
  Btrfs: do not change inode flags in rename
  Btrfs: use reserved space for creating a snapshot
  clear chunk_alloc flag on retryable failure
  ...

Pull MTD update from David Woodhouse:
 "Fairly unexciting MTD merge for 3.9:

   - misc clean-ups in the MTD command-line partitioning parser
     (cmdlinepart)
   - add flash locking support for STmicro chips serial flash chips, as
     well as for CFI command set 2 chips.
   - new driver for the ELM error correction HW module found in various
     TI chips, enable the OMAP NAND driver to use the ELM HW error
     correction
   - added number of new serial flash IDs
   - various fixes and improvements in the gpmi NAND driver
   - bcm47xx NAND driver improvements
   - make the mtdpart module actually removable"

* tag 'for-linus-20130301' of git://git.infradead.org/linux-mtd: (45 commits)
  mtd: map: BUG() in non handled cases
  mtd: bcm47xxnflash: use pr_fmt for module prefix in messages
  mtd: davinci_nand: Use managed resources
  mtd: mtd_torturetest can cause stack overflows
  mtd: physmap_of: Convert device allocation to managed devm_kzalloc()
  mtd: at91: atmel_nand: for PMECC, add code to check the ONFI parameter ECC requirement.
  mtd: atmel_nand: make pmecc-cap, pmecc-sector-size in dts is optional.
  mtd: atmel_nand: avoid to report an error when lookup table offset is 0.
  mtd: bcm47xxsflash: adjust names of bus-specific functions
  mtd: bcm47xxpart: improve probing of nvram partition
  mtd: bcm47xxpart: add support for other erase sizes
  mtd: bcm47xxnflash: register this as normal driver
  mtd: bcm47xxnflash: fix message
  mtd: bcm47xxsflash: register this as normal driver
  mtd: bcm47xxsflash: write number of written bytes
  mtd: gpmi: add sanity check for the ECC
  mtd: gpmi: set the Golois Field bit for mx6q's BCH
  mtd: devices: elm: Removes <xx> literals in elm DT node
  mtd: gpmi: fix a dereferencing freed memory error
  mtd: fix the wrong timeo for panic_nand_wait()
  ...

Reported-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

When using quota feature we need to enable quotas before orphan cleanup
so that changes happening during it are properly reflected in quota
accounting.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

So far we silently ignored when quota mount options were set while quota
feature was enabled.  But this can create confusion in userspace when
mount options are set but silently ignored and also creates opportunities
for bugs when we don't properly test all quota types.  Actually
ext4_mark_dquot_dirty() forgets to test for quota feature so it was
dependent on journaled quota options being set.  OTOH ext4_orphan_cleanup()
tries to enable journaled quota when quota options are specified which is
wrong when quota feature is enabled.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

ext4_dir_llseek is only used as a callback function, and no one calls
it directly.  So make it as a static function in order to remove a
warning message from sparse check.
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

We're using macro EXT4_B2C() to convert number of blocks to number of
clusters for bigalloc file systems.  However, we should be using
EXT4_NUM_B2C().
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org

'orig_data' is malloced in ext4_remount() and should be freed
before leaving from the error handling cases, otherwise it will
cause memory leak.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Lukas Czerner <lczerner@redhat.com>
Cc: stable@vger.kernel.org

If start_this_handle() failed handle will be initialized
to ERR_PTR() and can not be dereferenced.

paging request at fffffffffffffff6
IP: [<ffffffff813c073f>] jbd2__journal_start+0x18f/0x290
PGD 200e067 PUD 200f067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in: cpufreq_ondemand acpi_cpufreq freq_table mperf coretemp kvm_intel kvm crc32c_intel ghash_clmulni_intel microcode sg xhci_hcd button sd_mod crc_t10dif aesni_intel ablk_helper cryptd lrw aes_x86_64 xts gf128mul ahci libahci pata_acpi ata_generic dm_mirror dm_region_hash dm_log dm_mod
CPU 0 journal commit I/O error

Pid: 2694, comm: fio Not tainted 3.8.0-rc3+ #79                  /DQ67SW
RIP: 0010:[<ffffffff813c073f>]  [<ffffffff813c073f>] jbd2__journal_start+0x18f/0x290
RSP: 0018:ffff880233b8ba58  EFLAGS: 00010292
RAX: 00000000ffffffe2 RBX: ffffffffffffffe2 RCX: 0000000000000006
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffff82128f48
RBP: ffff880233b8ba98 R08: 0000000000000000 R09: ffff88021440a6e0
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

Pull device-mapper update from Alasdair G Kergon:
 "The main addition here is a long-desired target framework to allow an
  SSD to be used as a cache in front of a slower device.  Cache tuning
  is delegated to interchangeable policy modules so these can be
  developed independently of the mechanics needed to shuffle the data
  around.

  Other than that, kcopyd users acquire a throttling parameter, ioctl
  buffer usage gets streamlined, more mempool reliance is reduced and
  there are a few other bug fixes and tidy-ups."

* tag 'dm-3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm: (30 commits)
  dm cache: add cleaner policy
  dm cache: add mq policy
  dm: add cache target
  dm persistent data: add bitset
  dm persistent data: add transactional array
  dm thin: remove cells from stack
  dm bio prison: pass cell memory in
  dm persistent data: add btree_walk
  dm: add target num_write_bios fn
  dm kcopyd: introduce configurable throttling
  dm ioctl: allow message to return data
  dm ioctl: optimize functions without variable params
  dm ioctl: introduce ioctl_flags
  dm: merge io_pool and tio_pool
  dm: remove unused _rq_bio_info_cache
  dm: fix limits initialization when there are no data devices
  dm snapshot: add missing module aliases
  dm persistent data: set some btree fn parms const
  dm: refactor bio cloning
  dm: rename bio cloning functions
  ...

Pull SCSI target patches from Nicholas Bellinger:
 "Here are the remaining target-pending patches for v3.9-rc1.

  The most important one here is the immediate queue starvation
  regression fix for iscsi-target, which addresses a bug that's
  effecting v3.5+ kernels under heavy sustained READ only workloads.
  Thanks alot to Benjamin Estrabaud for helping to track this down!

  Also included is a pSCSI exception bugfix from Asias, along with a
  handful of other minor changes.  Both bugfixes are CC'ed to stable."

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target/pscsi: Rename sg_num to nr_vecs in pscsi_get_bio()
  target/pscsi: Fix page increment
  target/pscsi: Drop unnecessary NULL assignment to bio->bi_next
  target: Add __exit annotation for module_exit functions
  iscsi-target: Fix immediate queue starvation regression with DATAIN

Pull SCSI updates from James Bottomley:
 "This is an assorted set of stragglers into the merge window with
  driver updates for qla2xxx, megaraid_sas, storvsc and ufs.

  It also includes pulls of the uapi tree (all the remaining SCSI
  pieces) and the fcoe tree (updates to fcoe and libfc)"

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (81 commits)
  [SCSI] ufs: Separate PCI code into glue driver
  [SCSI] ufs: Segregate PCI Specific Code
  [SCSI] scsi: fix lpfc build when wmb() is defined as mb()
  [SCSI] storvsc: Handle dynamic resizing of the device
  [SCSI] storvsc: Restructure error handling code on command completion
  [SCSI] storvsc: avoid usage of WRITE_SAME
  [SCSI] aacraid: suppress two GCC warnings
  [SCSI] hpsa: check for dma_mapping_error in hpsa_passthru ioctls
  [SCSI] hpsa: reorganize error handling in hpsa_passthru_ioctl
  [SCSI] hpsa: check for dma_mapping_error in hpsa_map_sg_chain_block
  [SCSI] hpsa: Check for dma_mapping_error for all code paths using fill_cmd
  [SCSI] hpsa: Check for dma_mapping_error in hpsa_map_one
  [SCSI] dc395x: uninitialized variable in device_alloc()
  [SCSI] Fix range check in scsi_host_dif_capable()
  [SCSI] storvsc: Initialize the sglist
  [SCSI] mpt2sas: Add support for OEM specific controller
  [SCSI] ipr: Fix oops while resetting an ipr adapter
  [SCSI] fnic: Fnic Trace Utility
  [SCSI] fnic: New debug flags and debug log messages
  [SCSI] fnic: fnic driver may hit BUG_ON on device reset
  ...

Tim found:

  WARNING: at arch/x86/kernel/smpboot.c:324 topology_sane.isra.2+0x6f/0x80()
  Hardware name: S2600CP
  sched: CPU #1's llc-sibling CPU #0 is not on the same node! [node: 1 != 0]. Ignoring dependency.
  smpboot: Booting Node   1, Processors  #1
  Modules linked in:
  Pid: 0, comm: swapper/1 Not tainted 3.9.0-0-generic #1
  Call Trace:
    set_cpu_sibling_map+0x279/0x449
    start_secondary+0x11d/0x1e5

Don Morris reproduced on a HP z620 workstation, and bisected it to
commit e8d19552 ("acpi, memory-hotplug: parse SRAT before memblock
is ready")

It turns out movable_map has some problems, and it breaks several things

1. numa_init is called several times, NOT just for srat. so those
	nodes_clear(numa_nodes_parsed)
	memset(&numa_meminfo, 0, sizeof(numa_meminfo))
   can not be just removed.  Need to consider sequence is: numaq, srat, amd, dummy.
   and make fall back path working.

2. simply split acpi_numa_init to early_parse_srat.
   a. that early_parse_srat is NOT called for ia64, so you break ia64.
   b.  for (i = 0; i < MAX_LOCAL_APIC; i++)
	     set_apicid_to_node(i, NUMA_NO_NODE)
     still left in numa_init. So it will just clear result from early_parse_srat.
     it should be moved before that....
   c.  it breaks ACPI_TABLE_OVERIDE...as the acpi table scan is moved
       early before override from INITRD is settled.

3. that patch TITLE is total misleading, there is NO x86 in the title,
   but it changes critical x86 code. It caused x86 guys did not
   pay attention to find the problem early. Those patches really should
   be routed via tip/x86/mm.

4. after that commit, following range can not use movable ram:
  a. real_mode code.... well..funny, legacy Node0 [0,1M) could be hot-removed?
  b. initrd... it will be freed after booting, so it could be on movable...
  c. crashkernel for kdump...: looks like we can not put kdump kernel above 4G
	anymore.
  d. init_mem_mapping: can not put page table high anymore.
  e. initmem_init: vmemmap can not be high local node anymore. That is
     not good.

If node is hotplugable, the mem related range like page table and
vmemmap could be on the that node without problem and should be on that
node.

We have workaround patch that could fix some problems, but some can not
be fixed.

So just remove that offending commit and related ones including:

 f7210e6c ("mm/memblock.c: use CONFIG_HAVE_MEMBLOCK_NODE_MAP to
    protect movablecore_map in memblock_overlaps_region().")

 01a178a9 ("acpi, memory-hotplug: support getting hotplug info from
    SRAT")

 27168d38 ("acpi, memory-hotplug: extend movablemem_map ranges to
    the end of node")

 e8d19552 ("acpi, memory-hotplug: parse SRAT before memblock is
    ready")

 fb06bc8e ("page_alloc: bootmem limit with movablecore_map")

 42f47e27 ("page_alloc: make movablemem_map have higher priority")

 6981ec31 ("page_alloc: introduce zone_movable_limit[] to keep
    movable limit for nodes")

 34b71f1e ("page_alloc: add movable_memmap kernel parameter")

 4d59a751 ("x86: get pg_data_t's memory from other node")

Later we should have patches that will make sure kernel put page table
and vmemmap on local node ram instead of push them down to node0.  Also
need to find way to put other kernel used ram to local node ram.
Reported-by: Tim Gardner <tim.gardner@canonical.com>
Reported-by: Don Morris <don.morris@hp.com>
Bisected-by: Don Morris <don.morris@hp.com>
Tested-by: Don Morris <don.morris@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull signal/compat fixes from Al Viro:
 "Fixes for several regressions introduced in the last signal.git pile,
  along with fixing bugs in truncate and ftruncate compat (on just about
  anything biarch at least one of those two had been done wrong)."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
  compat: restore timerfd settime and gettime compat syscalls
  [regression] braino in "sparc: convert to ksignal"
  fix compat truncate/ftruncate
  switch lseek to COMPAT_SYSCALL_DEFINE
  lseek() and truncate() on sparc really need sign extension

Pull KGDB/KDB fixes and cleanups from Jason Wessel:
 "For a change we removed more code than we added.  If people aren't
  using it we shouldn't be carrying it.  :-)

  Cleanups:
   - Remove kdb ssb command - there is no in kernel disassembler to
     support it

   - Remove kdb ll command - Always caused a kernel oops and there were
     no bug reports so no one was using this command

   - Use kernel ARRAY_SIZE macro instead of array computations

  Fixes:
   - Stop oops in kdb if user executes kdb_defcmd with args

   - kdb help command truncated text

   - ppc64 support for kgdbts

   - Add missing kconfig option from original kdb port for dealing with
     catastrophic kernel crashes such that you can reboot automatically
     on continue from kdb"

* tag 'for_linux-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
  kdb: Remove unhandled ssb command
  kdb: Prevent kernel oops with kdb_defcmd
  kdb: Remove the ll command
  kdb_main: fix help print
  kdb: Fix overlap in buffers with strcpy
  Fixed dead ifdef block by adding missing Kconfig option.
  kdb: Setup basic kdb state before invoking commands via kgdb
  kdb: use ARRAY_SIZE where possible
  kgdb/kgdbts: support ppc64
  kdb: A fix for kdb command table expansion

Pull new ARC architecture from Vineet Gupta:
 "Initial ARC Linux port with some fixes on top for 3.9-rc1:

  I would like to introduce the Linux port to ARC Processors (from
  Synopsys) for 3.9-rc1.  The patch-set has been discussed on the public
  lists since Nov and has received a fair bit of review, specially from
  Arnd, tglx, Al and other subsystem maintainers for DeviceTree, kgdb...

  The arch bits are in arch/arc, some asm-generic changes (acked by
  Arnd), a minor change to PARISC (acked by Helge).

  The series is a touch bigger for a new port for 2 main reasons:

   1. It enables a basic kernel in first sub-series and adds
      ptrace/kgdb/.. later

   2. Some of the fallout of review (DeviceTree support, multi-platform-
      image support) were added on top of orig series, primarily to
      record the revision history.

  This updated pull request additionally contains

   - fixes due to our GNU tools catching up with the new syscall/ptrace
     ABI

   - some (minor) cross-arch Kconfig updates."

* tag 'arc-v3.9-rc1-late' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (82 commits)
  ARC: split elf.h into uapi and export it for userspace
  ARC: Fixup the current ABI version
  ARC: gdbserver using regset interface possibly broken
  ARC: Kconfig cleanup tracking cross-arch Kconfig pruning in merge window
  ARC: make a copy of flat DT
  ARC: [plat-arcfpga] DT arc-uart bindings change: "baud" => "current-speed"
  ARC: Ensure CONFIG_VIRT_TO_BUS is not enabled
  ARC: Fix pt_orig_r8 access
  ARC: [3.9] Fallout of hlist iterator update
  ARC: 64bit RTSC timestamp hardware issue
  ARC: Don't fiddle with non-existent caches
  ARC: Add self to MAINTAINERS
  ARC: Provide a default serial.h for uart drivers needing BASE_BAUD
  ARC: [plat-arcfpga] defconfig for fully loaded ARC Linux
  ARC: [Review] Multi-platform image #8: platform registers SMP callbacks
  ARC: [Review] Multi-platform image #7: SMP common code to use callbacks
  ARC: [Review] Multi-platform image #6: cpu-to-dma-addr optional
  ARC: [Review] Multi-platform image #5: NR_IRQS defined by ARC core
  ARC: [Review] Multi-platform image #4: Isolate platform headers
  ARC: [Review] Multi-platform image #3: switch to board callback
  ...

Pull MIPS updates from Ralf Baechle:

 o Add basic support for the Mediatek/Ralink Wireless SoC family.

 o The Qualcomm Atheros platform is extended by support for the new
   QCA955X SoC series as well as a bunch of patches that get the code
   ready for OF support.

 o Lantiq and BCM47XX platform have a few improvements and bug fixes.

 o MIPS has sent a few patches that get the kernel ready for the
   upcoming microMIPS support.

 o The rest of the series is made up of small bug fixes and cleanups
   that relate to various parts of the MIPS code.  The biggy in there is
   a whitespace cleanup.  After I was sent another set of whitespace
   cleanup patches I decided it was the time to clean the whitespace
   "issues" for once and and that touches many files below arch/mips/.

Fix up silly conflicts, mostly due to whitespace cleanups.

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (105 commits)
  MIPS: Quit exporting kernel internel break codes to uapi/asm/break.h
  MIPS: remove broken conditional inside vpe loader code
  MIPS: SMTC: fix implicit declaration of set_vi_handler
  MIPS: early_printk: drop __init annotations
  MIPS: Probe for and report hardware virtualization support.
  MIPS: ath79: add support for the Qualcomm Atheros AP136-010 board
  MIPS: ath79: add USB controller registration code for the QCA955X SoCs
  MIPS: ath79: add PCI controller registration code for the QCA955X SoCs
  MIPS: ath79: add WMAC registration code for the QCA955X SoCs
  MIPS: ath79: register UART for the QCA955X SoCs
  MIPS: ath79: add QCA955X specific glue to ath79_device_reset_{set, clear}
  MIPS: ath79: add GPIO setup code for the QCA955X SoCs
  MIPS: ath79: add IRQ handling code for the QCA955X SoCs
  MIPS: ath79: add clock setup code for the QCA955X SoCs
  MIPS: ath79: add SoC detection code for the QCA955X SoCs
  MIPS: ath79: add early printk support for the QCA955X SoCs
  MIPS: ath79: fix WMAC IRQ resource assignment
  mips: reserve elfcorehdr
  mips: Make sure kernel memory is in iomem
  MIPS: ath79: use dynamically allocated USB platform devices
  ...

Use a percpu counter rather than atomic types for shrinker accounting.
There's no need for ultimate accuracy in the shrinker, so this
should come a little more cheaply.  The percpu struct is somewhat
large, but there was a big gap before the cache-aligned
s_es_lru_lock anyway, and it fits nicely in there.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

The 'ssb' command can only be handled when we have a disassembler, to check for
branches, so remove the 'ssb' command for now.
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>

The kdb_defcmd can only be used to display the available command aliases
while using the kernel debug shell.  If you try to define a new macro
while the kernel debugger is active it will oops.  The debug shell
macros must use pre-allocated memory set aside at the time kdb_init()
is run, and the kdb_defcmd is restricted to only working at the time
that the kdb_init sequence is being run, which only occurs if you
actually activate the kernel debugger.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>

Recently some code inspection was done after fixing a problem with
kmalloc used while in the kernel debugger context (which is not
legal), and it turned up the fact that kdb ll command will oops the
kernel.

Given that there have been zero bug reports on the command combined
with the fact it will oops the kernel it is clearly not being used.
Instead of fixing it, it will be removed.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>

The help command was chopping all the usage instructions such that
they were not readable.

Example:

bta             [D|R|S|T|C|Z|E|U|I| Backtrace all processes matching state flag
per_cpu         <sym> [<bytes>] [<c Display per_cpu variables

Where as it should look like:

bta             [D|R|S|T|C|Z|E|U|I|M|A]
                                    Backtrace all processes matching state flag
per_cpu         <sym> [<bytes>] [<cpu>]
                                    Display per_cpu variables

All that is needed is to check the how long the cmd_usage is and jump
to the next line when appropriate.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>

Maxime reported that strcpy(s->usage, s->usage+1) has no definitive
guarantee that it will work on all archs the same way when you have
overlapping memory.  The fix is simple for the kdb code because we
still have the original string memory in the function scope, so we
just have to use that as the argument instead.
Reported-by: Maxime Villard <rustyBSD@gmx.fr>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>

Added missing Kconfig option KDB_CONTINUE_CATASTROPHIC which lead to a dead
ifdef block in kernel/debug/kdb/kdb_main.c:73-75.

The code using KDB_CONTINUE_CATASTROPHIC was originally introduced in
commit '5d5314d6' by Jason Wessel.
This patchset ("kdb: core for kgdb back end (1 of 2)")
added platform independent part of kdb to the linux kernel.

The Kernel option however, even though it had the same options and
behaviour on all supported architectures, was part of the x86 and
ia64 patchset of KDB and therefore not pulled into the mainline kernel tree.

I actually took the originally written Kconfig by
Keith Owens <kaos@sgi.com> (2003-06-20 according to KDB changelog)
and changed it to reflect the correct behaviour,
as the KDUMP patchset is not part of the kernel and the expected
functionality is missing from it.
Signed-off-by: Robert Obermeier <obbi89@googlemail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>

Although invasive kdb commands are not supported via kgdb, some useful
non-invasive commands like bt* require basic kdb state to be setup before
calling into the kdb code. Factor out some of this code and call it before
and after executing kdb commands via kgdb.
Signed-off-by: Matt Klein <mklein@twitter.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>

Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>

We can't look up the address of the entry point of the function simply
via that function symbol for all architectures.

For PPC64 ABI, actually there is a function descriptors structure.

A function descriptor is a three doubleword data structure that contains
the following values:
	* The first doubleword contains the address of the entry point of
		the function.
	* The second doubleword contains the TOC base address for
		the function.
	* The third doubleword contains the environment pointer for
		languages such as Pascal and PL/1.

So we should call a wapperred dereference_function_descriptor() to get
the address of the entry point of the function.

Note this is also safe for other architecture after refer to
"include/asm-generic/sections.h" since:

dereference_function_descriptor(p) always is (p) if without arched definition.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>

When locally adding in some additional kdb commands, I stumbled
across an issue with the dynamic expansion of the kdb command table.
When the number of kdb commands exceeds the size of the statically
allocated kdb_base_commands[] array, additional space is allocated in
the kdb_register_repeat() routine.

The unused portion of the newly allocated array was not being initialized
to zero properly and this would result in segfaults when help '?' was
executed or when a search for a non-existing command would traverse the
command table beyond the end of valid command entries and then attempt
to use the non-zeroed area as actual command entries.
Signed-off-by: John Blackwood <john.blackwood@ccur.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>

Both compat syscalls got lost with 9d94b9e2 "switch timerfd compat syscalls
to COMPAT_SYSCALL_DEFINE" because of a typo:
COMPAT instead of CONFIG_COMPAT.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>