Renaming bnxt_xmit_xdp to __bnxt_xmit_xdp to get ready for XDP_REDIRECT
support and reduce confusion/namespace collision.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ivan Khoronzhuk says:

====================
net: ethernet: ti: cpsw: Add XDP support

This patchset adds XDP support for TI cpsw driver and base it on
page_pool allocator. It was verified on af_xdp socket drop,
af_xdp l2f, ebpf XDP_DROP, XDP_REDIRECT, XDP_PASS, XDP_TX.

It was verified with following configs enabled:
CONFIG_JIT=y
CONFIG_BPFILTER=y
CONFIG_BPF_SYSCALL=y
CONFIG_XDP_SOCKETS=y
CONFIG_BPF_EVENTS=y
CONFIG_HAVE_EBPF_JIT=y
CONFIG_BPF_JIT=y
CONFIG_CGROUP_BPF=y

Link on previous v7:
https://lkml.org/lkml/2019/7/4/715

Also regular tests with iperf2 were done in order to verify impact on
regular netstack performance, compared with base commit:
https://pastebin.com/JSMT0iZ4

v8..v9:
- fix warnings on arm64 caused by typos in type casting

v7..v8:
- corrected dma calculation based on headroom instead of hard start
- minor comment changes

v6..v7:
- rolled back to v4 solution but with small modification
- picked up patch:
  https://www.spinics.net/lists/netdev/msg583145.html
- added changes related to netsec fix and cpsw

v5..v6:
- do changes that is rx_dev while redirect/flush cycle is kept the same
- dropped net: ethernet: ti: davinci_cpdma: return handler status
- other changes desc in patches

v4..v5:
- added two plreliminary patches:
  net: ethernet: ti: davinci_cpdma: allow desc split while down
  net: ethernet: ti: cpsw_ethtool: allow res split while down
- added xdp alocator refcnt on xdp level, avoiding page pool refcnt
- moved flush status as separate argument for cpdma_chan_process
- reworked cpsw code according to last changes to allocator
- added missed statistic counter

v3..v4:
- added page pool user counter
- use same pool for ndevs in dual mac
- restructured page pool create/destroy according to the last changes in API

v2..v3:
- each rxq and ndev has its own page pool

v1..v2:
- combined xdp_xmit functions
- used page allocation w/o refcnt juggle
- unmapped page for skb netstack
- moved rxq/page pool allocation to open/close pair
- added several preliminary patches:
  net: page_pool: add helper function to retrieve dma addresses
  net: page_pool: add helper function to unmap dma addresses
  net: ethernet: ti: cpsw: use cpsw as drv data
  net: ethernet: ti: cpsw_ethtool: simplify slave loops
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add XDP support based on rx page_pool allocator, one frame per page.
Page pool allocator is used with assumption that only one rx_handler
is running simultaneously. DMA map/unmap is reused from page pool
despite there is no need to map whole page.

Due to specific of cpsw, the same TX/RX handler can be used by 2
network devices, so special fields in buffer are added to identify
an interface the frame is destined to. Thus XDP works for both
interfaces, that allows to test xdp redirect between two interfaces
easily. Also, each rx queue have own page pools, but common for both
netdevs.

XDP prog is common for all channels till appropriate changes are added
in XDP infrastructure. Also, once page_pool recycling becomes part of
skb netstack some simplifications can be added, like removing
page_pool_release_page() before skb receive.

In order to keep rx_dev while redirect, that can be somehow used in
future, do flush in rx_handler, that allows to keep rx dev the same
while redirect. It allows to conform with tracing rx_dev pointed
by Jesper.

Also, there is probability, that XDP generic code can be extended to
support multi ndev drivers like this one, using same rx queue for
several ndevs, based on switchdev for instance or else. In this case,
driver can be modified like exposed here:
https://lkml.org/lkml/2019/7/3/243Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

That's possible to set channel num while interfaces are down. When
interface gets up it should resplit budget. This resplit can happen
after phy is up but only if speed is changed, so should be set before
this, for this allow it to happen while changing number of channels,
when interfaces are down.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

That's possible to set ring params while interfaces are down. When
interface gets up it uses number of descs to fill rx queue and on
later on changes to create rx pools. Usually, this resplit can happen
after phy is up, but it can be needed before this, so allow it to
happen while setting number of rx descs, when interfaces are down.
Also, if no dependency on intf state, move it to cpdma layer, where
it should be.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case if dma mapped packet needs to be sent, like with XDP
page pool, the "mapped" submit can be used. This patch adds dma
mapped submit based on regular one.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jesper recently removed page_pool_destroy() (from driver invocation)
and moved shutdown and free of page_pool into xdp_rxq_info_unreg(),
in-order to handle in-flight packets/pages. This created an asymmetry
in drivers create/destroy pairs.

This patch reintroduce page_pool_destroy and add page_pool user
refcnt. This serves the purpose to simplify drivers error handling as
driver now drivers always calls page_pool_destroy() and don't need to
track if xdp_rxq_info_reg_mem_model() was unsuccessful.

This could be used for a special cases where a single RX-queue (with a
single page_pool) provides packets for two net_device'es, and thus
needs to register the same page_pool twice with two xdp_rxq_info
structures.

This patch is primarily to ease API usage for drivers. The recently
merged netsec driver, actually have a bug in this area, which is
solved by this API change.

This patch is a modified version of Ivan Khoronzhuk's original patch.

Link: https://lore.kernel.org/netdev/20190625175948.24771-2-ivan.khoronzhuk@linaro.org/
Fixes: 5c67bf0e ("net: netsec: Use page_pool API")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_OF is disabled, we get a harmless warning about the
newly added variable:

drivers/net/ethernet/cadence/macb_main.c:48:39: error: 'mgmt' defined but not used [-Werror=unused-variable]
 static struct sifive_fu540_macb_mgmt *mgmt;

Move the variable closer to its use inside of the #ifdef.

Fixes: c218ad55 ("macb: Add support for SiFive FU540-C000")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

On unusual page sizes, we get harmless warnings:

drivers/net/ethernet/google/gve/gve_rx.c:283:6: error: unused variable 'pagecount' [-Werror,-Wunused-variable]
drivers/net/ethernet/google/gve/gve_rx.c:336:1: error: unused label 'have_skb' [-Werror,-Wunused-label]

Change the preprocessor #if to regular if() to avoid this.

Fixes: f5cedc84 ("gve: Add transmit and receive support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is only at notice level but it was pointed out that no other driver
does this.
Also there is no action the user can take as it is really a property of
the server.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS updates for net-next

The following patchset contains Netfilter/IPVS updates for net-next:

1) Move bridge keys in nft_meta to nft_meta_bridge, from wenxu.

2) Support for bridge pvid matching, from wenxu.

3) Support for bridge vlan protocol matching, also from wenxu.

4) Add br_vlan_get_pvid_rcu(), to fetch the bridge port pvid
   from packet path.

5) Prefer specific family extension in nf_tables.

6) Autoload specific family extension in case it is missing.

7) Add synproxy support to nf_tables, from Fernando Fernandez Mancera.

8) Support for GRE encapsulation in IPVS, from Vadim Fedorenko.

9) ICMP handling for GRE encapsulation, from Julian Anastasov.

10) Remove unused parameter in nf_queue, from Florian Westphal.

11) Replace seq_printf() by seq_puts() in nf_log, from Markus Elfring.

12) Rename nf_SYNPROXY.h => nf_synproxy.h before this header becomes
    public.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

cd1973a9 ("net: netsec: Sync dma for device on buffer allocation")
was merged on it's v1 instead of the v3.
Merge the proper patch version
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds firmware version query in ethtool -i.
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.

Fixes: f5cedc84 ("gve: Add transmit and receive support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pawel Dembicki says:

====================
net: dsa: Add Vitesse VSC73xx parallel mode

Main goal of this patch series is to add support for CPU attached parallel
bus in Vitesse VSC73xx switches. Existing driver supports only SPI mode.

Second change is needed for devices in unmanaged state.

V3:
- fix commit messages and descriptions about memory-mapped I/O mode

V2:
- drop changes in compatible strings
- make changes less invasive
- drop mutex in platform part and move mutex from core to spi part
- fix indentation
- fix devm_ioremap_resource result check
- add cover letter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver allow to use devices with disabled iCPU only.

Some devices have pre-initialised iCPU by bootloader.
That state make switch unmanaged. This patch force reset
if device is in unmanaged state. In the result chip lost
internal firmware from RAM and it can be managed.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add platform part of vsc73xx driver.
It allows to use chip connected to a parallel memory bus and work in
memory-mapped I/O mode. (aka PI bus in chip manual)

By default device is working in big endian mode.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver (currently) only takes control of the switch chip over
SPI and configures it to route packages around when connected to a
CPU port. But Vitesse chip support also parallel interface.

This patch split driver into two parts: core and spi. It is required
for add support to another managing interface.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit introduce how to use vsc73xx platform driver.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For these places are protected by rcu_read_lock, we change from
rcu_dereference_rtnl to rcu_dereference, as there is no need to
check if rtnl lock is held.

For these places are protected by rtnl_lock, we change from
rcu_dereference_rtnl to rtnl_dereference/rcu_dereference_protected,
as no extra memory barriers are needed under rtnl_lock() which also
protects tn->bearer_list[] and dev->tipc_ptr/b->media_ptr updating.

rcu_dereference_rtnl will be only used in the places where it could
be under rcu_read_lock or rtnl_lock.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch syncs the name of few chip versions with the latest vendor
driver version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2019-07-07

Here's the main bluetooth-next pull request for 5.3:

 - Added support for new devices from Qualcomm, Realtek and Broadcom and
   MediaTek
 - Various fixes to 6LoWPAN
 - Fix L2CAP PSM namespace separation for LE & BR/EDR
 - Fix behavior with Microsoft Surface Precision Mouse
 - Added support for LE Ping feature
 - Fix L2CAP Disconnect response handling if received in wrong state

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2019-07-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 5.3

Second, and last, set of patches for 5.3.

Major changes:

mt76

* use NAPI polling for tx cleanup on mt7603/mt7615

* add support for toggling edcca on mt7603

* fix rate control / tx status reporting issues on mt76x02/mt7603

* add support for eeprom calibration data from mtd on mt7615

* support configuring tx power on mt7615

* per-chain signal reporting on mt7615

iwlwifi

* Update the FW API for Channel State Information (CSI)

* Special Specific Absorption Rate (SAR) implementation for South Korea

ath10k

* fixes for SDIO support

* add support for firmware logging via WMI
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the support of enabling MT7663U Bluetooth function running
on the top of btusb driver.

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.

T:  Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  5 Spd=5000 MxCh= 0
D:  Ver= 3.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs=  1
P:  Vendor=0e8d ProdID=7663 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=160mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This adds the support of enabling MT7668U Bluetooth function running
on the top of btusb driver.

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.

T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=5000 MxCh= 0
D:  Ver= 3.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs=  1
P:  Vendor=0e8d ProdID=7668 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=160mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

BLE based 6LoWPAN networks are highly constrained in bandwidth.
Do not take a short-cut, always check if the destination address is
known to belong to a peer.

As a side-effect this also removes any behavioral differences between
one, and two or more connected peers.
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Tested-by: Michael Scott <mike@foundries.io>
Signed-off-by: Josua Mayer <josua.mayer@jm0.eu>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Like any IPv6 capable device, 6LNs can have multiple addresses assigned
using SLAAC and made known through neighbour advertisements.
After checking the destination address against all peers link-local
addresses, consult the neighbour cache for additional known addresses.

RFC7668 defines the scope of Neighbor Advertisements in Section 3.2.3:
1. "A Bluetooth LE 6LN MUST NOT register its link-local address"
2. "A Bluetooth LE 6LN MUST register its non-link-local addresses with
the 6LBR by sending Neighbor Solicitation (NS) messages ..."

Due to these constranits both the link-local addresses tracked in the
list of 6lowpan peers, and the neighbour cache have to be used when
identifying the 6lowpan peer for a destination address.
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Tested-by: Michael Scott <mike@foundries.io>
Signed-off-by: Josua Mayer <josua.mayer@jm0.eu>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Handle overlooked case where the target address is assigned to a peer
and neither route nor gateway exist.

For one peer, no checks are performed to see if it is meant to receive
packets for a given address.

As soon as there is a second peer however, checks are performed
to deal with routes and gateways for handling complex setups with
multiple hops to a target address.
This logic assumed that no route and no gateway imply that the
destination address can not be reached, which is false in case of a
direct peer.
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Tested-by: Michael Scott <mike@foundries.io>
Signed-off-by: Josua Mayer <josua.mayer@jm0.eu>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Microsoft Surface Precision Mouse provides bogus identity address when
pairing. It connects with Static Random address but provides Public
Address in SMP Identity Address Information PDU. Address has same
value but type is different. Workaround this by dropping IRK if ID
address discrepancy is detected.

> HCI Event: LE Meta Event (0x3e) plen 19
      LE Connection Complete (0x01)
        Status: Success (0x00)
        Handle: 75
        Role: Master (0x00)
        Peer address type: Random (0x01)
        Peer address: E0:52:33:93:3B:21 (Static)
        Connection interval: 50.00 msec (0x0028)
        Connection latency: 0 (0x0000)
        Supervision timeout: 420 msec (0x002a)
        Master clock accuracy: 0x00

....

> ACL Data RX: Handle 75 flags 0x02 dlen 12
      SMP: Identity Address Information (0x09) len 7
        Address type: Public (0x00)
        Address: E0:52:33:93:3B:21
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Tested-by: Maarten Fonville <maarten.fonville@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199461
Cc: stable@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The spec defines PSM and LE_PSM as different domains so a listen on the
same PSM is valid if the address type points to a different bearer.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This makes use of controller sets when using Extended Advertising
feature thus offloading the scheduling to the controller.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Problem: The Linux Bluetooth stack yields complete control over the BLE
connection interval to the remote device.

The Linux Bluetooth stack provides access to the BLE connection interval
min and max values through /sys/kernel/debug/bluetooth/hci0/
conn_min_interval and /sys/kernel/debug/bluetooth/hci0/conn_max_interval.
These values are used for initial BLE connections, but the remote device
has the ability to request a connection parameter update. In the event
that the remote side requests to change the connection interval, the Linux
kernel currently only validates that the desired value is within the
acceptable range in the Bluetooth specification (6 - 3200, corresponding to
7.5ms - 4000ms). There is currently no validation that the desired value
requested by the remote device is within the min/max limits specified in
the conn_min_interval/conn_max_interval configurations. This essentially
leads to Linux yielding complete control over the connection interval to
the remote device.

The proposed patch adds a verification step to the connection parameter
update mechanism, ensuring that the desired value is within the min/max
bounds of the current connection. If the desired value is outside of the
current connection min/max values, then the connection parameter update
request is rejected and the negative response is returned to the remote
device. Recall that the initial connection is established using the local
conn_min_interval/conn_max_interval values, so this allows the Linux
administrator to retain control over the BLE connection interval.

The one downside that I see is that the current default Linux values for
conn_min_interval and conn_max_interval typically correspond to 30ms and
50ms respectively. If this change were accepted, then it is feasible that
some devices would no longer be able to negotiate to their desired
connection interval values. This might be remedied by setting the default
Linux conn_min_interval and conn_max_interval values to the widest
supported range (6 - 3200 / 7.5ms - 4000ms). This could lead to the same
behavior as the current implementation, where the remote device could
request to change the connection interval value to any value that is
permitted by the Bluetooth specification, and Linux would accept the
desired value.
Signed-off-by: Carey Sonsino <csonsino@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Changes made to add HCI Write Authenticated Payload timeout
command for LE Ping feature.

As per the Core Specification 5.0 Volume 2 Part E Section 7.3.94,
the following code changes implements
HCI Write Authenticated Payload timeout command for LE Ping feature.
Signed-off-by: Spoorthi Ravishankar Koppad <spoorthix.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Because of both sides doing L2CAP disconnection at the same time, it
was possible to receive L2CAP Disconnection Response with CID that was
already freed. That caused problems if CID was already reused and L2CAP
Connection Request with same CID was sent out. Before this patch kernel
deleted channel context regardless of the state of the channel.

Example where leftover Disconnection Response (frame #402) causes local
device to delete L2CAP channel which was not yet connected. This in
turn confuses remote device's stack because same CID is re-used without
properly disconnecting.

Btmon capture before patch:
** snip **
> ACL Data RX: Handle 43 flags 0x02 dlen 8                #394 [hci1] 10.748949
      Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
      RFCOMM: Disconnect (DISC) (0x43)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x53 poll/final 1
         Length: 0
         FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8                #395 [hci1] 10.749062
      Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
      RFCOMM: Unnumbered Ack (UA) (0x63)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x73 poll/final 1
         Length: 0
         FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12               #396 [hci1] 10.749073
      L2CAP: Disconnection Request (0x06) ident 17 len 4
        Destination CID: 65
        Source CID: 65
> HCI Event: Number of Completed Packets (0x13) plen 5    #397 [hci1] 10.752391
        Num handles: 1
        Handle: 43
        Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5    #398 [hci1] 10.753394
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12               #399 [hci1] 10.756499
      L2CAP: Disconnection Request (0x06) ident 26 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12               #400 [hci1] 10.756548
      L2CAP: Disconnection Response (0x07) ident 26 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12               #401 [hci1] 10.757459
      L2CAP: Connection Request (0x02) ident 18 len 4
        PSM: 1 (0x0001)
        Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12               #402 [hci1] 10.759148
      L2CAP: Disconnection Response (0x07) ident 17 len 4
        Destination CID: 65
        Source CID: 65
= bluetoothd: 00:1E:AB:4C:56:54: error updating services: Input/o..   10.759447
> HCI Event: Number of Completed Packets (0x13) plen 5    #403 [hci1] 10.759386
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12               #404 [hci1] 10.760397
      L2CAP: Connection Request (0x02) ident 27 len 4
        PSM: 3 (0x0003)
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16               #405 [hci1] 10.760441
      L2CAP: Connection Response (0x03) ident 27 len 8
        Destination CID: 65
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27               #406 [hci1] 10.760449
      L2CAP: Configure Request (0x04) ident 19 len 19
        Destination CID: 65
        Flags: 0x0000
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 1013
        Option: Retransmission and Flow Control (0x04) [mandatory]
          Mode: Basic (0x00)
          TX window size: 0
          Max transmit: 0
          Retransmission timeout: 0
          Monitor timeout: 0
          Maximum PDU size: 0
> HCI Event: Number of Completed Packets (0x13) plen 5    #407 [hci1] 10.761399
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 16               #408 [hci1] 10.762942
      L2CAP: Connection Response (0x03) ident 18 len 8
        Destination CID: 66
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
*snip*

Similar case after the patch:
*snip*
> ACL Data RX: Handle 43 flags 0x02 dlen 8            #22702 [hci0] 1664.411056
      Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
      RFCOMM: Disconnect (DISC) (0x43)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x53 poll/final 1
         Length: 0
         FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8            #22703 [hci0] 1664.411136
      Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
      RFCOMM: Unnumbered Ack (UA) (0x63)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x73 poll/final 1
         Length: 0
         FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12           #22704 [hci0] 1664.411143
      L2CAP: Disconnection Request (0x06) ident 11 len 4
        Destination CID: 65
        Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22705 [hci0] 1664.414009
        Num handles: 1
        Handle: 43
        Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22706 [hci0] 1664.415007
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12           #22707 [hci0] 1664.418674
      L2CAP: Disconnection Request (0x06) ident 17 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12           #22708 [hci0] 1664.418762
      L2CAP: Disconnection Response (0x07) ident 17 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12           #22709 [hci0] 1664.421073
      L2CAP: Connection Request (0x02) ident 12 len 4
        PSM: 1 (0x0001)
        Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12           #22710 [hci0] 1664.421371
      L2CAP: Disconnection Response (0x07) ident 11 len 4
        Destination CID: 65
        Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22711 [hci0] 1664.424082
        Num handles: 1
        Handle: 43
        Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22712 [hci0] 1664.425040
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12           #22713 [hci0] 1664.426103
      L2CAP: Connection Request (0x02) ident 18 len 4
        PSM: 3 (0x0003)
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16           #22714 [hci0] 1664.426186
      L2CAP: Connection Response (0x03) ident 18 len 8
        Destination CID: 66
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27           #22715 [hci0] 1664.426196
      L2CAP: Configure Request (0x04) ident 13 len 19
        Destination CID: 65
        Flags: 0x0000
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 1013
        Option: Retransmission and Flow Control (0x04) [mandatory]
          Mode: Basic (0x00)
          TX window size: 0
          Max transmit: 0
          Retransmission timeout: 0
          Monitor timeout: 0
          Maximum PDU size: 0
> ACL Data RX: Handle 43 flags 0x02 dlen 16           #22716 [hci0] 1664.428804
      L2CAP: Connection Response (0x03) ident 12 len 8
        Destination CID: 66
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
*snip*

Fix is to check that channel is in state BT_DISCONN before deleting the
channel.

This bug was found while fuzzing Bluez's OBEX implementation using
Synopsys Defensics.
Reported-by: Matti Kamunen <matti.kamunen@synopsys.com>
Reported-by: Ari Timonen <ari.timonen@synopsys.com>
Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This change is similar to commit a1616a5a ("Bluetooth: hidp: fix
buffer overflow") but for the compat ioctl.  We take a string from the
user and forgot to ensure that it's NUL terminated.

I have also changed the strncpy() in to strscpy() in hidp_setup_hid().
The difference is the strncpy() doesn't necessarily NUL terminate the
destination string.  Either change would fix the problem but it's nice
to take a belt and suspenders approach and do both.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Without the QCA ROME setup routine this adapter fails to establish a SCO
connection.

T:  Bus=01 Lev=01 Prnt=01 Port=08 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3491 Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#=0x1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Without the QCA ROME setup routine this adapter fails to establish a SCO
connection.

T:  Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3501 Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#=0x1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Syzkaller found that it is possible to provoke a memory leak by
never freeing rx_skb in struct bcsp_struct.

Fix by freeing in bcsp_close()
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+98162c885993b72f19c4@syzkaller.appspotmail.com
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This device is functionally equivalent to the BT part of the RTL8723DE,
uses the same firmware, but the LMP subversion and HCI revision are unique.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Some board requires explicitily control external osscilator via GPIO.
So, add an implementation of a clock property for an external oscillator
to the device.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>