- 29 May, 2013 6 commits
-
-
-
Alexander Bondar authored
Add debugfs files to control powersave parameters for testing. Signed-off-by:Johannes Berg <johannes.berg@intel.com>
-
Hila Gonen authored
The firmware supports periodic keep alive and beacon monitoring, so advertise connection monitor offload capability by setting IEEE80211_HW_CONNECTION_MONITOR flag. Implement missed beacons notification handler. Call ieee80211_beacon_loss in case of missed beacons, so AP probing by mac80211 can be triggered. Signed-off-by:
Hila Gonen <hila.gonen@intel.com> Reviewed-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
I forgot to take them from TLV and took them from the NVM instead. Signed-off-by:
Ilan Peer <ilan.peer@intel.com> Signed-off-by:
-
Alexander Bondar authored
If skip over DTIMs is enabled the driver can specify number of DTIMs to skip. This parameter in host-device API implies number of DTIM periods to skip. For example, to skip one DTIM means sleep over two DTIM periods. Change semantics accordingly. Change this parameter's default value. Signed-off-by:
Alexander Bondar <alexander.bondar@intel.com> Reviewed-by:
-
Eytan Lifshitz authored
In order to avoid NIC destruction due to high temperature, CT kill will power down the NIC. To avoid this, thermal throttling will decrease throughput to prevent the NIC from reaching the temperature at which CT kill is performed. Signed-off-by:
Eytan Lifshitz <eytan.lifshitz@intel.com> Signed-off-by:
-
- 27 May, 2013 8 commits
-
-
Emmanuel Grumbach authored
It was set to be FORCED because of a firmware bug which has been fixed. Signed-off-by:
-
Johannes Berg authored
Conflicts: drivers/net/wireless/iwlwifi/mvm/ops.c
-
Alexander Bondar authored
Beacon abort is used by device to increase idle dwell time when system is idle. This algorithm is on top of beacon filtering feature. Enable beacon abort only if power management is enabled. Signed-off-by:
-
Johannes Berg authored
The pointer that gets used is already const, so the structs can obviously be const as well. Reviewed-by:
-
Johannes Berg authored
There are a number of parameters that aren't really hardware specific but rather define how the DVM firmware is used. Move these into the DVM configuration. Reviewed-by:
-
Johannes Berg authored
The next patches will move some more configuration data that isn't needed by mvm into this struct, so rename it now since it won't just be ops. Reviewed-by:
-
Johannes Berg authored
The MVM firmware doesn't communicate this way, it instead assumes D3 configuration is complete after a specific host command (which must be last) has been sent. Handling this bit thus belongs into the firmware API code, i.e. DVM. Signed-off-by:
-
Emmanuel Grumbach authored
In 63b77bf4 iwlwifi: dvm: don't send zeroed LQ cmd I tried to avoid to send zeroed LQ cmd, but I made a (very) stupid mistake in the memcmp. Since this patch has been ported to stable, the fix should go to stable too. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=58341 Cc: stable@vger.kernel.org Reported-by:
Hinnerk van Bruinehsen <h.v.bruinehsen@fu-berlin.de> Signed-off-by:
-
- 24 May, 2013 26 commits
-
-
Nishant Sarmukadam authored
The firmware hang issue is not seen very often, though it is still seen sometimes (once in 12 hours in local tests). The changes in the driver ,to interrupt the firmware, are needed when we detect that firmware is stuck and when the host queues are full and we begin to drop packets. This is to ensure that the firmware does not miss any PPA_RDY interrupts to cause the firmware restart dont miss PPA_READY interrupt for SC2 Signed-off-by:
Nishant Sarmukadam <nishants@marvell.com> Signed-off-by:
Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Wei Yongjun authored
Use kfree_skb() instead of kfree() to free sk_buff. Introduced by commit e270045b (wil6210: Sanity check for reported DMA length) Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
Stanislaw Gruszka <stf_xl@wp.pl> Acked-by:
Helmut Schaa <helmut.schaa@googlemail.com> Acked-by:
Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Create helper function and move initialization to subroutines. Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
