This patch lists the Cypress TrueTouch Touchscreen as a consumer
of the AB8500 VAUX1 regulator.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch lists the Pressure sensor as a consumer of the AB8500
VAUX1 regulator.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch lists the Ambient light sensor device as a consumer
of the AB8500 VAUX1 regulator.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch lists the L3G4200D Gyroscope as a consumer of the
AB8500 VAUX1 regulator.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add 3 more specific consumers pertaining to the displays found
on the u8500 and ST User Interface Boards (UIBs).
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The data sheet does not specify time delay for voltage selection,
thus remove set_voltage_time_sel and delay setting.

Note, currently set_voltage_time_sel callback returns 0 due to missing
delay settings.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Base on the data provide by Bengt Jönsson, add below enable_time settings:

Worst case enable time from data sheet:
Vana: enable time = 140 us
Vaux1/2: enable time = 200 us
Vaux3: enable time = 450 us
Vintcore: enable time = 750 us
Vamic1/2: enable time = 500 us
Vdmic: enable time = 420 us
VTVout: enable time = 500 us
Vaudio: enable time = 140 us
Vusb: enable time = 150 us

This discussion thread is available at: https://lkml.org/lkml/2013/3/26/795Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This avoid setting is_enabled flag to wrong status if enable/disable fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Both ab8500_regulator_mode_ops and ab8500_regulator_ops do not have volt_table
setting, thus we can not use regulator_list_voltage_table for them.
However, they have min_uV setting with n_voltages = 1, so use
regulator_list_voltage_linear instead.

Also remove setting set_voltage_time_sel for ab8500_regulator_mode_ops.
It is used only for fixed voltage, so it does not need to implement
set_voltage_time_sel.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Fix below build error:

  CC      drivers/regulator/ab8500.o
drivers/regulator/ab8500.c:500:23: error: 'ab8500_regulator_fixed_ops' undeclared here (not in a function)
drivers/regulator/ab8500.c: In function 'ab8500_regulator_probe':
drivers/regulator/ab8500.c:972:8: warning: assignment from incompatible pointer type [enabled by default]
make[2]: *** [drivers/regulator/ab8500.o] Error 1
make[1]: *** [drivers/regulator] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The ab8500 MFD should not have knowledge about regulator-
specific platform data like number of regulators and
regulator registers. As the regulator platform data is
about to grow with external regulators, this information
is moved to a new structure provided by the regulator
driver.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Yvan FILLION <yvan.fillion@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch ensures that many of the recent developments pertaining to
the AB8500 regulator device are propagated out into the public arena.
It aims to update some of the existing initialisation values in
accordance with internal ST-Ericsson code submissions. This single
patch was originally a collection of updates which have been squashed
together to aid with clarity.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

There is already before a register mask in the regulator driver
to allow some bits of a register to be initialized. The register
value is defined in the board configuration. This patch puts a
mask in the board configuration to specify which bits should
actually be altered. The purpose with this patch is to avoid
future mistakes when updating the allowed bits in the regulator
driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

With this change, Vtvout, Vintcore12, Vaux1, 2 and 3 regulators
support DRMS (Dynamic Regulator Mode Switching) which will
dynamically handle requests for max current consumption from
several consumers and select a suitable regulator mode.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Ludovic Barré <ludovic.barre@stericsson.com>
Signed-off-by: Emeric Vigier <emeric.vigier@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bengt JONSSON <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch supplies access to some extra settings provided by the
AB8500 regulator device. We also update some of the existing
initialisation values in accordance with internal ST-Ericsson code
submissions. This single patch was originally a collection of updates
which have been squashed together to aid with clarity.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Commit 1d9d8639 ("perf,x86: fix kernel crash with PEBS/BTS after
suspend/resume") introduces a link failure since
perf_restore_debug_store() is only defined for CONFIG_CPU_SUP_INTEL:

	arch/x86/power/built-in.o: In function `restore_processor_state':
	(.text+0x45c): undefined reference to `perf_restore_debug_store'

Fix it by defining the dummy function appropriately.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 1d9d8639 ("perf,x86: fix kernel crash with PEBS/BTS after
suspend/resume") fixed a crash when doing PEBS performance profiling
after resuming, but in using init_debug_store_on_cpu() to restore the
DS_AREA mtrr it also resulted in a new WARN_ON() triggering.

init_debug_store_on_cpu() uses "wrmsr_on_cpu()", which in turn uses CPU
cross-calls to do the MSR update.  Which is not really valid at the
early resume stage, and the warning is quite reasonable.  Now, it all
happens to _work_, for the simple reason that smp_call_function_single()
ends up just doing the call directly on the CPU when the CPU number
matches, but we really should just do the wrmsr() directly instead.

This duplicates the wrmsr() logic, but hopefully we can just remove the
wrmsr_on_cpu() version eventually.
Reported-and-tested-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull btrfs fixes from Chris Mason:
 "Eric's rcu barrier patch fixes a long standing problem with our
  unmount code hanging on to devices in workqueue helpers.  Liu Bo
  nailed down a difficult assertion for in-memory extent mappings."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix warning of free_extent_map
  Btrfs: fix warning when creating snapshots
  Btrfs: return as soon as possible when edquot happens
  Btrfs: return EIO if we have extent tree corruption
  btrfs: use rcu_barrier() to wait for bdev puts at unmount
  Btrfs: remove btrfs_try_spin_lock
  Btrfs: get better concurrency for snapshot-aware defrag work

Users report that an extent map's list is still linked when it's actually
going to be freed from cache.

The story is that

a) when we're going to drop an extent map and may split this large one into
smaller ems, and if this large one is flagged as EXTENT_FLAG_LOGGING which means
that it's on the list to be logged, then the smaller ems split from it will also
be flagged as EXTENT_FLAG_LOGGING, and this is _not_ expected.

b) we'll keep ems from unlinking the list and freeing when they are flagged with
EXTENT_FLAG_LOGGING, because the log code holds one reference.

The end result is the warning, but the truth is that we set the flag
EXTENT_FLAG_LOGGING only during fsync.

So clear flag EXTENT_FLAG_LOGGING for extent maps split from a large one.
Reported-by: Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de>
Reported-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>

Pull kbuild fix from Michal Marek:
 "One fix for for make headers_install/headers_check to not require make
  3.81.  The requirement has been accidentally introduced in 3.7."

* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  kbuild: fix make headers_check with make 3.80

Pull OpenRISC bug fixes from Jonas Bonn:

 - The GPIO descriptor work has exposed how broken the non-GPIOLIB bits
   for OpenRISC were.  We now require GPIOLIB as this is the preferred
   way forward.

 - The system.h split introduced a bug in llist.h for arches using
   asm-generic/cmpxchg.h directly, which is currently only OpenRISC.
   The patch here moves two defines from asm-generic/atomic.h to
   asm-generic/cmpxchg.h to make things work as they should.

 - The VIRT_TO_BUS selector was added for OpenRISC, but OpenRISC does
   not have the virt_to_bus methods, so there's a patch to remove it
   again.

* tag 'for-3.9-rc3' of git://openrisc.net/jonas/linux:
  openrisc: remove HAVE_VIRT_TO_BUS
  asm-generic: move cmpxchg*_local defs to cmpxchg.h
  openrisc: require gpiolib

Pull char/misc fixes from Greg Kroah-Hartman:
 "Here are some tiny fixes for the w1 drivers and the final removal
  patch for getting rid of CONFIG_EXPERIMENTAL (all users of it are now
  gone from your tree, this just drops the Kconfig item itself.)

  All have been in the linux-next tree for a while"

* tag 'char-misc-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  final removal of CONFIG_EXPERIMENTAL
  w1: fix oops when w1_search is called from netlink connector
  w1-gpio: fix unused variable warning
  w1-gpio: remove erroneous __exit and __exit_p()
  ARM: w1-gpio: fix erroneous gpio requests

Pull sound fixes from Takashi Iwai:
 "A collection of small fixes, as expected for the middle rc:
   - A couple of fixes for potential NULL dereferences and out-of-range
     array accesses revealed by static code parsers
   - A fix for the wrong error handling detected by trinity
   - A regression fix for missing audio on some MacBooks
   - CA0132 DSP loader fixes
   - Fix for EAPD control of IDT codecs on machines w/o speaker
   - Fix a regression in the HD-audio widget list parser code
   - Workaround for the NuForce UDH-100 USB audio"

* tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Fix missing EAPD/GPIO setup for Cirrus codecs
  sound: sequencer: cap array index in seq_chn_common_event()
  ALSA: hda/ca0132 - Remove extra setting of dsp_state.
  ALSA: hda/ca0132 - Check download state of DSP.
  ALSA: hda/ca0132 - Check if dspload_image succeeded.
  ALSA: hda - Disable IDT eapd_switch if there are no internal speakers
  ALSA: hda - Fix snd_hda_get_num_raw_conns() to return a correct value
  ALSA: usb-audio: add a workaround for the NuForce UDH-100
  ALSA: asihpi - fix potential NULL pointer dereference
  ALSA: seq: Fix missing error handling in snd_seq_timer_open()

Pull DMA-mapping fix from Marek Szyprowski:
 "An important fix for all ARM architectures which use ZONE_DMA.
  Without it dma_alloc_* calls with GFP_ATOMIC flag might have allocated
  buffers outsize DMA zone."

* 'fixes-for-3.9' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
  ARM: DMA-mapping: add missing GFP_DMA flag for atomic buffer allocation

Pull MFD fixes from Samuel Ortiz:
 "This is the first batch of MFD fixes for 3.9.

  With this one we have:

   - An ab8500 build failure fix.
   - An ab8500 device tree parsing fix.
   - A fix for twl4030_madc remove routine to work properly (when
     built-in).
   - A fix for properly registering palmas interrupt handler.
   - A fix for omap-usb init routine to actually write into the
     hostconfig register.
   - A couple of warning fixes for ab8500-gpadc and tps65912"

* tag 'mfd-fixes-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-fixes:
  mfd: twl4030-madc: Remove __exit_p annotation
  mfd: ab8500: Kill "reg" property from binding
  mfd: ab8500-gpadc: Complain if we fail to enable vtvout LDO
  mfd: wm831x: Don't forward declare enum wm831x_auxadc
  mfd: twl4030-audio: Fix argument type for twl4030_audio_disable_resource()
  mfd: tps65912: Declare and use tps65912_irq_exit()
  mfd: palmas: Provide irq flags through DT/platform data
  mfd: Make AB8500_CORE select POWER_SUPPLY to fix build error
  mfd: omap-usb-host: Actually update hostconfig

Pull hwmon fixes from Guenter Roeck:
 "Bug fixes for pmbus, ltc2978, and lineage-pem drivers

  Added specific maintainer for some hwmon drivers"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (pmbus/ltc2978) Fix temperature reporting
  hwmon: (pmbus) Fix krealloc() misuse in pmbus_add_attribute()
  hwmon: (lineage-pem) Add missing terminating entry for pem_[input|fan]_attributes
  MAINTAINERS: Add maintainer for MAX6697, INA209, and INA2XX drivers

This patch fixes a kernel crash when using precise sampling (PEBS)
after a suspend/resume. Turns out the CPU notifier code is not invoked
on CPU0 (BP). Therefore, the DS_AREA (used by PEBS) is not restored properly
by the kernel and keeps it power-on/resume value of 0 causing any PEBS
measurement to crash when running on CPU0.

The workaround is to add a hook in the actual resume code to restore
the DS Area MSR value. It is invoked for all CPUS. So for all but CPU0,
the DS_AREA will be restored twice but this is harmless.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

During the transition to the generic parser, the hook to the codec
specific automute function was forgotten.  This resulted in the silent
output on some MacBooks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

"chn" here is a number between 0 and 255, but ->chn_info[] only has
16 elements so there is a potential write beyond the end of the
array.

If the seq_mode isn't SEQ_2 then we let the individual drivers
(either opl3.c or midi_synth.c) handle it.  Those functions all
do a bounds check on "chn" so I haven't changed anything here.
The opl3.c driver has up to 18 channels and not 16.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

4740f73f "mfd: remove use of __devexit" removed the __devexit annotation
on the twl4030_madc_remove function, but left an __exit_p() present on the
pointer to this function. Using __exit_p was as wrong with the devexit in
place as it is now, but now we get a gcc warning about an unused function.

In order for the twl4030_madc_remove to work correctly in built-in code, we
have to remove the __exit_p.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

spec->dsp_state is initialized to DSP_DOWNLOAD_INIT, no need to reset
and check it in ca0132_download_dsp().
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Instead of using the dspload_is_loaded() function, check the dsp_state
that is kept in the spec.  The dspload_is_loaded() function returns
true if the DSP transfer was never started.  This false-positive leads
to multiple second delays when ca0132_setup_efaults() times out on
each write.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

If dspload_image() fails, it was ignored and dspload_wait_loaded() was
still called.  dsp_loaded should never be set to true in this case,
skip it.  The check in dspload_wait_loaded() return true if the DSP is
loaded or if it never started.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The vm_flags introduced in 6d7825b1 ("mm/fremap.c: fix oops on error
path") is supposed to avoid a compiler warning about unitialized
vm_flags without changing the generated code.

However I am concerned that this is going to be very brittle, and fail
with some compiler versions. The failure could be either of:

- compiler could actually load vma->vm_flags before checking for the
  !vma condition, thus reintroducing the oops

- compiler could optimize out the !vma check, since the pointer just got
  dereferenced shortly before (so the compiler knows it can't be NULL!)

I propose reversing this part of the change and initializing vm_flags to 0
just to avoid the bogus uninitialized use warning.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull fix for hlist_entry_safe() regression from Paul McKenney:
 "This contains a single commit that fixes a regression in
  hlist_entry_safe().  This macro references its argument twice, which
  can cause NULL-pointer errors.  This commit applies a gcc statement
  expression, creating a temporary variable to avoid the double
  reference.  This has been posted to LKML at

    https://lkml.org/lkml/2013/3/9/75.

  Kudos to CAI Qian, whose testing uncovered this, to Eric Dumazet, who
  spotted root cause, and to Li Zefan, who tested this commit."

* 'rcu/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
  list: Fix double fetch of pointer in hlist_entry_safe()

The current version of hlist_entry_safe() fetches the pointer twice,
once to test for NULL and the other to compute the offset back to the
enclosing structure.  This is OK for normal lock-based use because in
that case, the pointer cannot change.  However, when the pointer is
protected by RCU (as in "rcu_dereference(p)"), then the pointer can
change at any time.  This use case can result in the following sequence
of events:

1.	CPU 0 invokes hlist_entry_safe(), fetches the RCU-protected
	pointer as sees that it is non-NULL.

2.	CPU 1 invokes hlist_del_rcu(), deleting the entry that CPU 0
	just fetched a pointer to.  Because this is the last entry
	in the list, the pointer fetched by CPU 0 is now NULL.

3.	CPU 0 refetches the pointer, obtains NULL, and then gets a
	NULL-pointer crash.

This commit therefore applies gcc's "({ })" statement expression to
create a temporary variable so that the specified pointer is fetched
only once, avoiding the above sequence of events.  Please note that
it is the caller's responsibility to use rcu_dereference() as needed.
This allows RCU-protected uses to work correctly without imposing
any additional overhead on the non-RCU case.

Many thanks to Eric Dumazet for spotting root cause!
Reported-by: CAI Qian <caiqian@redhat.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Li Zefan <lizefan@huawei.com>

Pull ext2, ext3, reiserfs, quota fixes from Jan Kara:
 "A fix for regression in ext2, and a format string issue in ext3.  The
  rest isn't too serious."

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  ext2: Fix BUG_ON in evict() on inode deletion
  reiserfs: Use kstrdup instead of kmalloc/strcpy
  ext3: Fix format string issues
  quota: add missing use of dq_data_lock in __dquot_initialize

Creating snapshot passes extent_root to commit its transaction,
but it can lead to the warning of checking root for quota in
the __btrfs_end_transaction() when someone else is committing
the current transaction.  Since we've recorded the needed root
in trans_handle, just use it to get rid of the warning.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>