This makes it clear that we're dealing with a queue
of TRBs. No functional changes. While at that, also
rename start_slot to first_trb_index for similar
reasons.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The DWC3 OMAP driver supports DT-boot only, as result dma_mask will be
always configured properly from DT -
of_platform_device_create_pdata()->of_dma_configure(). More over,
dwc3-omap.c can be built as module and in this case it's unsafe to
assign local variable as dma_mask.

Hence, remove dma_mask configuration code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Some freescale QorIQ platforms require to disable receiver detection
in P3 for correct detection of USB devices. If GUSB3PIPECTL(DISRXDETINP3)
is set, Core will change PHY power state to P2 and then perform receiver
detection. After receiver detection, Core will change PHY power state to
P3. Same quirk would be added in dts file in future patches.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add snps,dis_rxdet_inp3_quirk property which disables receiver detection
in PHY P3 power state.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Synopsys Databook says we should move link to U0
before issuing a Start Transfer command. We could
require the gadget driver to call
usb_gadget_wakeup() however I feel that changing all
gadget drivers to keep track of Link State and
conditionally call usb_gadget_wakeup() would be far
too much work. For now we will handle this at the
UDC level, but at some point composite.c should be
one handling this.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

we will need this from StartTransfer to make sure
link is in U0 before starting a transfer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Synopsys Databook 2.60a has a note that if we're
sending an endpoint command we _must_ make sure that
DWC3_GUSB2PHY(n).SUSPHY bit is cleared.

This patch implements that particular detail.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

dwc3_send_gadget_ep_cmd() had three return
points. That becomes a pain to track when we need to
debug something or if we need to add more code
before returning.

Let's combine all three return points into a single
one just by introducing a local 'ret' variable.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Sort IDs in groups to be easily found when needed.

There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

It seems there are leftovers of some assignments which are not used
anymore.  Compiler even warns us about:

drivers/usb/gadget/udc/pch_udc.c:2022:22: warning: variable ‘dev’ set \
but not used [-Wunused-but-set-variable]

drivers/usb/gadget/udc/pch_udc.c:2639:9: warning: variable ‘ret’ set \
but not used [-Wunused-but-set-variable]

Remove them and shut compiler about.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Try to enable MSI in case hardware supports it. At least Intel Quark is
known SoC which indeed does.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

devres API allows to make error paths cleaner and less error
prone. Convert the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

There is no need to repeat the work that is already done in the PCI
driver core. The patch removes excerpts from suspend and resume
callbacks.

Note that there is no more calls performed to enable or disable a PCI
device during suspend-resume cycle. Nowadays they seems to be
superfluous. Someone can read more in [1].

While here, convert PM ops to use modern API.

[1] https://www.kernel.org/doc/ols/2009/ols2009-pages-319-330.pdfSigned-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

[felipe.balbi@linux.intel.com: fixed build break and checkpatch error ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The phy-am335x driver selects 'USB_COMMON', but all other drivers
use 'depends on' for that symbol, and it depends on USB || USB_GADGET
itself, which causes a Kconfig warning:

warning: (AM335X_PHY_USB) selects USB_COMMON which has unmet direct dependencies (USB_SUPPORT && (USB || USB_GADGET))

As suggested by Felipe Balbi, this turns the logic around, and makes
'USB_COMMON' selected by everything else that needs it, so we can
remove the dependencies.

Fixes: 59f042f6 ("usb: phy: phy-am335x: bypass first VBUS sensing for host-only mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

we don't plan on using multiple event buffers, but
if we find a good use case for it, this little trick
will help us avoid a loop in hardirq handler looping
for each and every event buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

we will be using a single event buffer and that
renders ev_buffs array unnecessary. Let's remove it
in favor of a single pointer to a single event
buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We never, ever route any of the other event buffers
so we might as well drop support for them.

Until someone has a real, proper benefit for
multiple event buffers, we will rely on a single
one. This also helps reduce memory footprint of
dwc3.ko which won't allocate memory for the extra
event buffers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

coccicheck found this pattern which could be
converted to PTR_ERR_OR_ZERO(). No functional
changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

coccicheck found this pattern which could be
converted to PTR_ERR_OR_ZERO(). No functional
changes.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

request_list and req_queued were, well, weird naming
choices.

Let's give those better names and call them,
respectively, pending_list and started_list. These
new names better reflect what these lists are
supposed to do.

While at that also rename req->queued to req->started.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

previously we were using a maximum of 32 TRBs per
endpoint. With each TRB being 16 bytes long, we were
using 512 bytes of memory for each endpoint.

However, SLAB/SLUB will always allocate PAGE_SIZE
chunks. In order to better utilize the memory we
allocate and to allow deeper queues for gadgets
which would benefit from it (g_ether comes to mind),
let's increase the maximum to 256 TRBs which rounds
up to 4096 bytes for each endpoint.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

CSP bit of TRB Control is useful for protocols such
CDC EEM/ECM/NCM where we're transferring in blocks
of MTU-sized requests (usually MTU is 1500 bytes).

We know we will always have a short packet after two
(for HS) wMaxPacketSize packets and, usually, we
will have a long(-ish) queue of requests (for our
g_ether gadget, we have at least 10
requests).

Instead of always stopping the queue processing to
interrupt, giveback and restart, let's tell dwc3 to
interrupt but continue processing following request
if we have anything already pending in the queue.

This gave me a considerable improvement of 40% on my
test setup.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

That FIFO resizing logic was added to support OMAP5
ES1.0 which had a bogus default FIFO size. I can't
remember the exact size of default FIFO, but it was
less than one bulk superspeed packet (<1024) which
would prevent USB3 from ever working on OMAP5 ES1.0.

However, OMAP5 ES1.0 support has been dropped by
commit aa2f4b16 ("ARM: OMAP5: id: Remove ES1.0
support") which renders FIFO resizing unnecessary.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Pull ARM fixes from Russell King:
 "A couple of small fixes, and wiring up the new syscalls which appeared
  during the merge window"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8550/1: protect idiv patching against undefined gcc behavior
  ARM: wire up preadv2 and pwritev2 syscalls
  ARM: SMP enable of cache maintanence broadcast

Pull MMC fixes from Ulf Hansson:
 "Here are a couple of mmc fixes intended for v4.6 rc3:

  MMC host:
   - sdhci: Fix regression setting power on Trats2 board
   - sdhci-pci: Add support and PCI IDs for more Broxton host controllers"

* tag 'mmc-v4.6-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
  mmc: sdhci-pci: Add support and PCI IDs for more Broxton host controllers
  mmc: sdhci: Fix regression setting power on Trats2 board

Pull i2c fixes from Wolfram Sang:
 "Some bugfixes from I2C:

   - fix a uevent triggered boot problem by removing a useless debug
     print

   - fix sysfs-attributes of the new i2c-demux-pinctrl driver to follow
     standard kernel behaviour

   - fix a potential division-by-zero error (needed two takes)"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: jz4780: really prevent potential division by zero
  Revert "i2c: jz4780: prevent potential division by zero"
  i2c: jz4780: prevent potential division by zero
  i2c: mux: demux-pinctrl: Update docs to new sysfs-attributes
  i2c: mux: demux-pinctrl: Clean up sysfs attributes
  i2c: prevent endless uevent loop with CONFIG_I2C_DEBUG_CORE

This reverts commit 1028b55b.

It's broken: it makes ext4 return an error at an invalid point, causing
the readdir wrappers to write the the position of the last successful
directory entry into the position field, which means that the next
readdir will now return that last successful entry _again_.

You can only return fatal errors (that terminate the readdir directory
walk) from within the filesystem readdir functions, the "normal" errors
(that happen when the readdir buffer fills up, for example) happen in
the iterorator where we know the position of the actual failing entry.

I do have a very different patch that does the "signal_pending()"
handling inside the iterator function where it is allowable, but while
that one passes all the sanity checks, I screwed up something like four
times while emailing it out, so I'm not going to commit it today.

So my track record is not good enough, and the stars will have to align
better before that one gets committed.  And it would be good to get some
review too, of course, since celestial alignments are always an iffy
debugging model.

IOW, let's just revert the commit that caused the problem for now.
Reported-by: Greg Thelen <gthelen@google.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull parisc fixes from Helge Deller:
 "Since commit 0de79858 ("parisc: Use generic extable search and
  sort routines") module loading is boken on parisc, because the parisc
  module loader wasn't prepared for the new R_PARISC_PCREL32 relocations.

  In addition, due to that breakage, Mikulas Patocka noticed that
  handling exceptions from modules probably never worked on parisc.  It
  was just masked by the fact that exceptions from modules don't happen
  during normal use.

  This patch series fixes those issues and survives the tests of the
  lib/test_user_copy kernel module test.  Some patches are tagged for
  stable"

* 'parisc-4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Update comment regarding relative extable support
  parisc: Unbreak handling exceptions from kernel modules
  parisc: Fix kernel crash with reversed copy_from_user()
  parisc: Avoid function pointers for kernel exception routines
  parisc: Handle R_PARISC_PCREL32 relocations in kernel modules

Pull libnvdimm fixes from Dan Williams:
 "Three fixes, the first two are tagged for -stable:

   - The ndctl utility/library gained expanded unit tests illuminating a
     long standing bug in the libnvdimm SMART data retrieval
     implementation.

     It has been broken since its initial implementation, now fixed.

   - Another one line fix for the detection of stale info blocks.

     Without this change userspace can get into a situation where it is
     unable to reconfigure a namespace.

   - Fix the badblock initialization path in the presence of the new (in
     v4.6-rc1) section alignment workarounds.

     Without this change badblocks will be reported at the wrong offset.

  These have received a build success report from the kbuild robot and
  have appeared in -next with no reported issues"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm, pfn: fix nvdimm_namespace_add_poison() vs section alignment
  libnvdimm, pfn: fix uuid validation
  libnvdimm: fix smart data retrieval

Pull GPIO fixes from Linus Walleij:
 "Here is a set of four GPIO fixes.  The two fixes to the core are
  serious as they are regressing minor architectures.

  Core fixes:

   - Defer GPIO device setup until after gpiolib is initialized.

     It turns out that a few very tightly integrated GPIO platform
     drivers initialize so early (befor core_initcall()) so that the
     gpiolib isn't even initialized itself.  That limits what the
     library can do, and we cannot reference uninitialized fields until
     later.

     Defer some of the initialization until right after the gpiolib is
     initialized in these (rare) cases.

   - As a consequence: do not use devm_* resources when allocating the
     states in the initial set-up of the gpiochip.

  Driver fixes:

   - In ACPI retrieveal: ignore GpioInt when looking for output GPIOs.

   - Fix legacy builds on the PXA without a backing pin controller.

   - Use correct datatype on pca953x register writes"

* tag 'gpio-v4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: pca953x: Use correct u16 value for register word write
  gpiolib: Defer gpio device setup until after gpiolib initialization
  gpiolib: Do not use devm functions when registering gpio chip
  gpio: pxa: fix legacy non pinctrl aware builds
  gpio / ACPI: ignore GpioInt() GPIOs when requesting GPIO_OUT_*

Pull tty fixes from Greg KH:
 "Here are two tty fixes for issues found.

  One was due to a merge error in 4.6-rc1, and the other a regression
  fix for UML consoles that broke in 4.6-rc1.

  Both have been in linux-next for a while"

* tag 'tty-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: Fix merge of "tty: Refactor tty_open()"
  tty: Fix UML console breakage

Pull USB fixes from Greg KH:
 "Here are some USB fixes and new device ids for 4.6-rc3.

  Nothing major, the normal USB gadget fixes and usb-serial driver ids,
  along with some other fixes mixed in.  All except the USB serial ids
  have been tested in linux-next, the id additions should be fine as
  they are 'trivial'"

* tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
  USB: option: add "D-Link DWM-221 B1" device id
  USB: serial: cp210x: Adding GE Healthcare Device ID
  USB: serial: ftdi_sio: Add support for ICP DAS I-756xU devices
  usb: dwc3: keystone: drop dma_mask configuration
  usb: gadget: udc-core: remove manual dma configuration
  usb: dwc3: pci: add ID for one more Intel Broxton platform
  usb: renesas_usbhs: fix to avoid using a disabled ep in usbhsg_queue_done()
  usb: dwc2: do not override forced dr_mode in gadget setup
  usb: gadget: f_midi: unlock on error
  USB: digi_acceleport: do sanity checking for the number of ports
  USB: cypress_m8: add endpoint sanity check
  USB: mct_u232: add sanity checking in probe
  usb: fix regression in SuperSpeed endpoint descriptor parsing
  USB: usbip: fix potential out-of-bounds write
  usb: renesas_usbhs: disable TX IRQ before starting TX DMAC transfer
  usb: renesas_usbhs: avoid NULL pointer derefernce in usbhsf_pkt_handler()
  usb: gadget: f_midi: Fixed a bug when buflen was smaller than wMaxPacketSize
  usb: phy: qcom-8x16: fix regulator API abuse
  usb: ch9: Fix SSP Device Cap wFunctionalitySupport type
  usb: gadget: composite: Access SSP Dev Cap fields properly
  ...

Pull staging and IIO driver fixes from Greg KH:
 "Here are some IIO driver fixes, along with two staging driver fixes
  for 4.6-rc3.

  One staging driver patch reverts the deletion of a driver that
  happened in 4.6-rc1.  We thought that laptop.org was dead, but it's
  still alive and kicking, and has users that were mad we broke their
  hardware by deleting a driver for their machines.  So that driver is
  added back and everyone is happy again.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  Revert "Staging: olpc_dcon: Remove obsolete driver"
  staging/rdma/hfi1: select CRC32
  iio: gyro: bmg160: fix buffer read values
  iio: gyro: bmg160: fix endianness when reading axes
  iio: accel: bmc150: fix endianness when reading axes
  iio: st_magn: always define ST_MAGN_TRIGGER_SET_STATE
  iio: fix config watermark initial value
  iio: health: max30100: correct FIFO check condition
  iio: imu: Fix inv_mpu6050 dependencies
  iio: adc: Fix build error of missing devm_ioremap_resource on UM
  iio: light: apds9960: correct FIFO check condition
  iio: adc: max1363: correct reference voltage
  iio: adc: max1363: add missing adc to max1363_id

Pull SCSI fixes from James Bottomley:
 "This is a set of eight fixes.

  Two are trivial gcc-6 updates (brace additions and unused variable
  removal).  There's a couple of cxlflash regressions, a correction for
  sd being overly chatty on revalidation (causing excess log increases).
  A VPD issue which could crash USB devices because they seem very
  intolerant to VPD inquiries, an ALUA deadlock fix and a mpt3sas buffer
  overrun fix"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: Do not attach VPD to devices that don't support it
  sd: Fix excessive capacity printing on devices with blocks bigger than 512 bytes
  scsi_dh_alua: Fix a recently introduced deadlock
  scsi: Declare local symbols static
  cxlflash: Move to exponential back-off when cmd_room is not available
  cxlflash: Fix regression issue with re-ordering patch
  mpt3sas: Don't overreach ioc->reply_post[] during initialization
  aacraid: add missing curly braces

Pull MD fixes from Shaohua Li:
 "This update mainly fixes bugs:

   - fix error handling (Guoqing)
   - fix a crash when a disk is hotremoved (me)
   - fix a dead loop (Wei Fang)"

* tag 'md/4.6-rc2-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  md/bitmap: clear bitmap if bitmap_create failed
  MD: add rdev reference for super write
  md: fix a trivial typo in comments
  md:raid1: fix a dead loop when read from a WriteMostly disk

Pull power management and ACPI fixes from Rafael Wysocki:
 "Fixes for some issues discovered after recent changes and for some
  that have just been found lately regardless of those changes
  (intel_pstate, intel_idle, PM core, mailbox/pcc, turbostat) plus
  support for some new CPU models (intel_idle, Intel RAPL driver,
  turbostat) and documentation updates (intel_pstate, PM core).

  Specifics:

   - intel_pstate fixes for two issues exposed by the recent switch over
     from using timers and for one issue introduced during the 4.4 cycle
     plus new comments describing data structures used by the driver
     (Rafael Wysocki, Srinivas Pandruvada).

   - intel_idle fixes related to CPU offline/online (Richard Cochran).

   - intel_idle support (new CPU IDs and state definitions mostly) for
     Skylake-X and Kabylake processors (Len Brown).

   - PCC mailbox driver fix for an out-of-bounds memory access that may
     cause the kernel to panic() (Shanker Donthineni).

   - New (missing) CPU ID for one apparently overlooked Haswell model in
     the Intel RAPL power capping driver (Srinivas Pandruvada).

   - Fix for the PM core's wakeup IRQs framework to make it work after
     wakeup settings reconfiguration from sysfs (Grygorii Strashko).

   - Runtime PM documentation update to make it describe what needs to
     be done during device removal more precisely (Krzysztof Kozlowski).

   - Stale comment removal cleanup in the cpufreq-dt driver (Viresh
     Kumar).

   - turbostat utility fixes and support for Broxton, Skylake-X and
     Kabylake processors (Len Brown)"

* tag 'pm+acpi-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
  PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfs
  tools/power turbostat: work around RC6 counter wrap
  tools/power turbostat: initial KBL support
  tools/power turbostat: initial SKX support
  tools/power turbostat: decode BXT TSC frequency via CPUID
  tools/power turbostat: initial BXT support
  tools/power turbostat: print IRTL MSRs
  tools/power turbostat: SGX state should print only if --debug
  intel_idle: Add KBL support
  intel_idle: Add SKX support
  intel_idle: Clean up all registered devices on exit.
  intel_idle: Propagate hot plug errors.
  intel_idle: Don't overreact to a cpuidle registration failure.
  intel_idle: Setup the timer broadcast only on successful driver load.
  intel_idle: Avoid a double free of the per-CPU data.
  intel_idle: Fix dangling registration on error path.
  intel_idle: Fix deallocation order on the driver exit path.
  intel_idle: Remove redundant initialization calls.
  intel_idle: Fix a helper function's return value.
  intel_idle: remove useless return from void function.
  ...

Pull networking fixes from David Miller:

 1) Stale SKB data pointer access across pskb_may_pull() calls in L2TP,
    from Haishuang Yan.

 2) Fix multicast frame handling in mac80211 AP code, from Felix
    Fietkau.

 3) mac80211 station hashtable insert errors not handled properly, fix
    from Johannes Berg.

 4) Fix TX descriptor count limit handling in e1000, from Alexander
    Duyck.

 5) Revert a buggy netdev refcount fix in netpoll, from Bjorn Helgaas.

 6) Must assign rtnl_link_ops of the device before registering it, fix
    in ip6_tunnel from Thadeu Lima de Souza Cascardo.

 7) Memory leak fix in tc action net exit, from WANG Cong.

 8) Add missing AF_KCM entries to name tables, from Dexuan Cui.

 9) Fix regression in GRE handling of csums wrt.  FOU, from Alexander
    Duyck.

10) Fix memory allocation alignment and congestion map corruption in
    RDS, from Shamir Rabinovitch.

11) Fix default qdisc regression in tuntap driver, from Jason Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
  bridge, netem: mark mailing lists as moderated
  tuntap: restore default qdisc
  mpls: find_outdev: check for err ptr in addition to NULL check
  ipv6: Count in extension headers in skb->network_header
  RDS: fix congestion map corruption for PAGE_SIZE > 4k
  RDS: memory allocated must be align to 8
  GRE: Disable segmentation offloads w/ CSUM and we are encapsulated via FOU
  net: add the AF_KCM entries to family name tables
  MAINTAINERS: intel-wired-lan list is moderated
  lib/test_bpf: Add additional BPF_ADD tests
  lib/test_bpf: Add test to check for result of 32-bit add that overflows
  lib/test_bpf: Add tests for unsigned BPF_JGT
  lib/test_bpf: Fix JMP_JSET tests
  VSOCK: Detach QP check should filter out non matching QPs.
  stmmac: fix adjust link call in case of a switch is attached
  af_packet: tone down the Tx-ring unsupported spew.
  net_sched: fix a memory leak in tc action
  samples/bpf: Enable powerpc support
  samples/bpf: Use llc in PATH, rather than a hardcoded value
  samples/bpf: Fix build breakage with map_perf_test_user.c
  ...

Pull btrfs fixes from Chris Mason:
 "These are bug fixes, including a really old fsync bug, and a few trace
  points to help us track down problems in the quota code"

* 'for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix file/data loss caused by fsync after rename and new inode
  btrfs: Reset IO error counters before start of device replacing
  btrfs: Add qgroup tracing
  Btrfs: don't use src fd for printk
  btrfs: fallback to vmalloc in btrfs_compare_tree
  btrfs: handle non-fatal errors in btrfs_qgroup_inherit()
  btrfs: Output more info for enospc_debug mount option
  Btrfs: fix invalid reference in replace_path
  Btrfs: Improve FL_KEEP_SIZE handling in fallocate

Pull orangefs fixes from Mike Marshall:
 "Orangefs cleanups and a strncpy vulnerability fix.

  Cleanups:
   - remove an unused variable from orangefs_readdir.
   - clean up printk wrapper used for ofs "gossip" debugging.
   - clean up truncate ctime and mtime setting in inode.c
   - remove a useless null check found by coccinelle.
   - optimize some memcpy/memset boilerplate code.
   - remove some useless sanity checks from xattr.c

  Fix:
   - fix a potential strncpy vulnerability"

* tag 'for-linus-4.6-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
  orangefs: remove unused variable
  orangefs: Add KERN_<LEVEL> to gossip_<level> macros
  orangefs: strncpy -> strscpy
  orangefs: clean up truncate ctime and mtime setting
  Orangefs: fix ifnullfree.cocci warnings
  Orangefs: optimize boilerplate code.
  Orangefs: xattr.c cleanup