Since the beginning of the parisc-linux port, sometimes 64bit SMP kernels were
not able to bring up other CPUs than the monarch CPU and instead crashed the
kernel.  The reason was unclear, esp. since it involved various machines (e.g.
J5600, J6750 and SuperDome). Testing showed, that those crashes didn't happened
when less than 4GB were installed, or if a 32bit Linux kernel was booted.

In the end, the fix for those SMP problems is trivial:
During the early phase of the initialization of the CPUs, including the monarch
CPU, the PDC_PSW firmware function to enable WIDE (=64bit) mode is called.
It's documented that this firmware function may clobber various registers, and
one one of those possibly clobbered registers is %cr30 which holds the task
thread info pointer.

Now, if %cr30 would always have been clobbered, then this bug would have been
detected much earlier. But lots of testing finally showed, that - at least for
%cr30 - on some machines only the upper 32bits of the 64bit register suddenly
turned zero after the firmware call.

So, after finding the root cause, the explanation for the various crashes
became clear:
- On 32bit SMP Linux kernels all upper 32bit were zero, so we didn't faced this
  problem.
- Monarch CPUs in 64bit mode always booted sucessfully, because the inital task
  thread info pointer was below 4GB.
- Secondary CPUs booted sucessfully on machines with less than 4GB RAM because
  the upper 32bit were zero anyay.
- Secondary CPus failed to boot if we had more than 4GB RAM and the task thread
  info pointer was located above the 4GB boundary.

Finally, the patch to fix this problem is trivial by saving the %cr30 register
before the firmware call and restoring it afterwards.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # 2.6.12+
Signed-off-by: Helge Deller <deller@gmx.de>

Pull ACPI and power management fixes from
 "These fix two bugs in the intel_pstate driver, a hibernate bug leading
  to nasty resume failures sometimes and acpi-cpufreq initialization bug
  that causes problems to happen during module unload when intel_pstate
  is in use.

  Specifics:

   - Fix for rounding errors in intel_pstate causing CPU utilization to
     be underestimated from Brennan Shacklett.

   - intel_pstate fix to always use the correct max pstate value when
     computing the min pstate from Dirk Brandewie.

   - Hibernation fix for deadlocking resume in cases when the probing of
     the device containing the image is deferred from Russ Dill.

   - acpi-cpufreq fix to prevent the module from staying in memory when
     the driver cannot be registered and then attempting to unregister
     things that have never been registered on exit"

* tag 'pm+acpi-3.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  acpi-cpufreq: Fail initialization if driver cannot be registered
  PM / hibernate: Move software_resume to late_initcall_sync
  intel_pstate: Correct calculation of min pstate value
  intel_pstate: Improve accuracy by not truncating until final result

Pull final mtd fixes from Brian Norris:
 "A few more last-minute regression fixes, prepared jointly by me and
  David Woodhouse:

   - Revert pxa3xx to its old name to avoid breaking existing
     'mtdparts=' boot strings.

   - Return GPMI NAND to its legacy ECC layout for backwards
     compatibility.  We will revisit this in 3.13.

  A note from David on the latter fix: 'This leaves a harmless cosmetic
  warning about an unused function.  At this point in the cycle I really
  don't care.'"

* tag 'for-linus-20131025' of git://git.infradead.org/linux-mtd:
  mtd: gpmi: fix ECC regression
  mtd: nand: pxa3xx: Fix registered MTD name

Pull vfs fixes (try two) from Al Viro:
 "nfsd performance regression fix + seq_file lseek(2) fix"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  seq_file: always update file->f_pos in seq_lseek()
  nfsd regression since delayed fput()

The "legacy" ECC layout used until 3.12-rc1 uses all the OOB area by
computing the ECC strength and ECC step size ourselves.

Commit 2febcdf8 ("mtd: gpmi: set the BCHs geometry with the ecc info")
makes the driver use the ECC info (ECC strength and ECC step size)
provided by the MTD code, and creates a different NAND ECC layout
for the BCH, and use the new ECC layout. This causes a regression:

   We can not mount the ubifs which was created by the old NAND ECC layout.

This patch fixes this issue by reverting to the legacy ECC layout.

We will probably introduce a new device-tree property to indicate that
the new ECC layout can be used. For now though, for the imminent 3.12
release, we just unconditionally revert to the 3.11 behaviour.

This leaves a harmless cosmetic warning about an unused function. At
this point in the cycle I really don't care.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>

This issue was first pointed out by Jiaxing Wang several months ago, but no
further comments:
https://lkml.org/lkml/2013/6/29/41

As we know pread() does not change f_pos, so after pread(), file->f_pos
and m->read_pos become different. And seq_lseek() does not update file->f_pos
if offset equals to m->read_pos, so after pread() and seq_lseek()(lseek to
m->read_pos), then a subsequent read may read from a wrong position, the
following program produces the problem:

    char str1[32] = { 0 };
    char str2[32] = { 0 };
    int poffset = 10;
    int count = 20;

    /*open any seq file*/
    int fd = open("/proc/modules", O_RDONLY);

    pread(fd, str1, count, poffset);
    printf("pread:%s\n", str1);

    /*seek to where m->read_pos is*/
    lseek(fd, poffset+count, SEEK_SET);

    /*supposed to read from poffset+count, but this read from position 0*/
    read(fd, str2, count);
    printf("read:%s\n", str2);

out put:
pread:
 ck_netbios_ns 12665
read:
 nf_conntrack_netbios

/proc/modules:
nf_conntrack_netbios_ns 12665 0 - Live 0xffffffffa038b000
nf_conntrack_broadcast 12589 1 nf_conntrack_netbios_ns, Live 0xffffffffa0386000

So we always update file->f_pos to offset in seq_lseek() to fix this issue.
Signed-off-by: Jiaxing Wang <hello.wjx@gmail.com>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Make acpi_cpufreq_init() return error codes when the driver cannot be
registered so that the module doesn't stay useless in memory and so
that acpi_cpufreq_exit() doesn't attempt to unregister things that
have never been registered when the module is unloaded.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>

Pull ARM SoC fixes from Olof Johansson:
 "There's really only one bugfix in this branch, which is a fix for
  timers on the integrator platform.  Since Linus Walleij is
  resurrecting support for the platform it seems valuable to get the fix
  into 3.12 even though the regression has been around a while.

  The rest are a handful of maintainers updates.  If you prefer to hold
  those until 3.13 then just merge the first patch on the branch which
  is the fix"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  MAINTAINERS: Add maintainers entry for Rockchip SoCs
  MAINTAINERS: Tegra updates, and driver ownership
  MAINTAINERS: ARM: mvebu: add Sebastian Hesselbarth
  ARM: integrator: deactivate timer0 on the Integrator/CP

Merge tag 'ecryptfs-3.12-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull ecryptfs fixes from Tyler Hicks:
 "Two important fixes
   - Fix long standing memory leak in the (rarely used) public key
     support
   - Fix large file corruption on 32 bit architectures"

* tag 'ecryptfs-3.12-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: fix 32 bit corruption issue
  ecryptfs: Fix memory leakage in keystore.c

software_resume is being called after deferred_probe_initcall in
drivers base. If the probing of the device that contains the resume
image is deferred, and the system has been instructed to wait for
it to show up, this wait will occur in software_resume. This causes
a deadlock.

Move software_resume into late_initcall_sync so that it happens
after all the other late_initcalls.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Pavel Machek <Pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

In a recent commit:

  commit f455578d
  Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
  Date:   Mon Aug 12 14:14:53 2013 -0300

  mtd: nand: pxa3xx: Remove hardcoded mtd name

  There's no advantage in using a hardcoded name for the mtd device.
  Instead use the provided by the platform_device.

The MTD name was changed to use the one provided by the platform_device.
However, this can be problematic as some users want to set partitions
using the kernel parameter 'mtdparts', where the name is needed.

Therefore, to avoid regressions in users relying in 'mtdparts' we revert
the change and use the previous one 'pxa3xx_nand-0'.

While at it, let's put a big comment and prevent this change from happening
ever again.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Shifting page->index on 32 bit systems was overflowing, causing
data corruption of > 4GB files. Fix this by casting it first.

https://launchpad.net/bugs/1243636Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reported-by: Lars Duesing <lars.duesing@camelotsweb.de>
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>

Pull md bugfixes from Neil Brown:
 "Assorted md bug-fixes for 3.12.

  All tagged for -stable releases too"

* tag 'md/3.12-fixes' of git://neil.brown.name/md:
  raid5: avoid finding "discard" stripe
  raid5: set bio bi_vcnt 0 for discard request
  md: avoid deadlock when md_set_badblocks.
  md: Fix skipping recovery for read-only arrays.

Pull SCSI fixes from James Bottomley:
 "This is a set of two fixes which cause oopses (Buslogic, qla2xxx) and
 one fix which may cause a hang because of request miscounting (sd)"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] sd: call blk_pm_runtime_init before add_disk
  [SCSI] qla2xxx: Fix request queue null dereference.
  [SCSI] BusLogic: Fix an oops when intializing multimaster adapter

SCSI discard will damage discard stripe bio setting, eg, some fields are
changed. If the stripe is reused very soon, we have wrong bios setting. We
remove discard stripe from hash list, so next time the strip will be fully
initialized.

Suitable for backport to 3.7+.

Cc: <stable@vger.kernel.org> (3.7+)
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>

SCSI layer will add new payload for discard request. If two bios are merged
to one, the second bio has bi_vcnt 1 which is set in raid5. This will confuse
SCSI and cause oops.

Suitable for backport to 3.7+

Cc: stable@vger.kernel.org (v3.7+)
Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>

When operate harddisk and hit errors, md_set_badblocks is called after
scsi_restart_operations which already disabled the irq. but md_set_badblocks
will call write_sequnlock_irq and enable irq. so softirq can preempt the
current thread and that may cause a deadlock. I think this situation should
use write_sequnlock_irqsave/irqrestore instead.

I met the situation and the call trace is below:
[  638.919974] BUG: spinlock recursion on CPU#0, scsi_eh_13/1010
[  638.921923]  lock: 0xffff8800d4d51fc8, .magic: dead4ead, .owner: scsi_eh_13/1010, .owner_cpu: 0
[  638.923890] CPU: 0 PID: 1010 Comm: scsi_eh_13 Not tainted 3.12.0-rc5+ #37
[  638.925844] Hardware name: To be filled by O.E.M. To be filled by O.E.M./MAHOBAY, BIOS 4.6.5 03/05/2013
[  638.927816]  ffff880037ad4640 ffff880118c03d50 ffffffff8172ff85 0000000000000007
[  638.929829]  ffff8800d4d51fc8 ffff880118c03d70 ffffffff81730030 ffff8800d4d51fc8
[  638.931848]  ffffffff81a72eb0 ffff880118c03d90 ffffffff81730056 ffff8800d4d51fc8
[  638.933884] Call Trace:
[  638.935867]  <IRQ>  [<ffffffff8172ff85>] dump_stack+0x55/0x76
[  638.937878]  [<ffffffff81730030>] spin_dump+0x8a/0x8f
[  638.939861]  [<ffffffff81730056>] spin_bug+0x21/0x26
[  638.941836]  [<ffffffff81336de4>] do_raw_spin_lock+0xa4/0xc0
[  638.943801]  [<ffffffff8173f036>] _raw_spin_lock+0x66/0x80
[  638.945747]  [<ffffffff814a73ed>] ? scsi_device_unbusy+0x9d/0xd0
[  638.947672]  [<ffffffff8173fb1b>] ? _raw_spin_unlock+0x2b/0x50
[  638.949595]  [<ffffffff814a73ed>] scsi_device_unbusy+0x9d/0xd0
[  638.951504]  [<ffffffff8149ec47>] scsi_finish_command+0x37/0xe0
[  638.953388]  [<ffffffff814a75e8>] scsi_softirq_done+0xa8/0x140
[  638.955248]  [<ffffffff8130e32b>] blk_done_softirq+0x7b/0x90
[  638.957116]  [<ffffffff8104fddd>] __do_softirq+0xfd/0x330
[  638.958987]  [<ffffffff810b964f>] ? __lock_release+0x6f/0x100
[  638.960861]  [<ffffffff8174a5cc>] call_softirq+0x1c/0x30
[  638.962724]  [<ffffffff81004c7d>] do_softirq+0x8d/0xc0
[  638.964565]  [<ffffffff8105024e>] irq_exit+0x10e/0x150
[  638.966390]  [<ffffffff8174ad4a>] smp_apic_timer_interrupt+0x4a/0x60
[  638.968223]  [<ffffffff817499af>] apic_timer_interrupt+0x6f/0x80
[  638.970079]  <EOI>  [<ffffffff810b964f>] ? __lock_release+0x6f/0x100
[  638.971899]  [<ffffffff8173fa6a>] ? _raw_spin_unlock_irq+0x3a/0x50
[  638.973691]  [<ffffffff8173fa60>] ? _raw_spin_unlock_irq+0x30/0x50
[  638.975475]  [<ffffffff81562393>] md_set_badblocks+0x1f3/0x4a0
[  638.977243]  [<ffffffff81566e07>] rdev_set_badblocks+0x27/0x80
[  638.978988]  [<ffffffffa00d97bb>] raid5_end_read_request+0x36b/0x4e0 [raid456]
[  638.980723]  [<ffffffff811b5a1d>] bio_endio+0x1d/0x40
[  638.982463]  [<ffffffff81304ff3>] req_bio_endio.isra.65+0x83/0xa0
[  638.984214]  [<ffffffff81306b9f>] blk_update_request+0x7f/0x350
[  638.985967]  [<ffffffff81306ea1>] blk_update_bidi_request+0x31/0x90
[  638.987710]  [<ffffffff813085e0>] __blk_end_bidi_request+0x20/0x50
[  638.989439]  [<ffffffff8130862f>] __blk_end_request_all+0x1f/0x30
[  638.991149]  [<ffffffff81308746>] blk_peek_request+0x106/0x250
[  638.992861]  [<ffffffff814a62a9>] ? scsi_kill_request.isra.32+0xe9/0x130
[  638.994561]  [<ffffffff814a633a>] scsi_request_fn+0x4a/0x3d0
[  638.996251]  [<ffffffff813040a7>] __blk_run_queue+0x37/0x50
[  638.997900]  [<ffffffff813045af>] blk_run_queue+0x2f/0x50
[  638.999553]  [<ffffffff814a5750>] scsi_run_queue+0xe0/0x1c0
[  639.001185]  [<ffffffff814a7721>] scsi_run_host_queues+0x21/0x40
[  639.002798]  [<ffffffff814a2e87>] scsi_restart_operations+0x177/0x200
[  639.004391]  [<ffffffff814a4fe9>] scsi_error_handler+0xc9/0xe0
[  639.005996]  [<ffffffff814a4f20>] ? scsi_unjam_host+0xd0/0xd0
[  639.007600]  [<ffffffff81072f6b>] kthread+0xdb/0xe0
[  639.009205]  [<ffffffff81072e90>] ? flush_kthread_worker+0x170/0x170
[  639.010821]  [<ffffffff81748cac>] ret_from_fork+0x7c/0xb0
[  639.012437]  [<ffffffff81072e90>] ? flush_kthread_worker+0x170/0x170

This bug was introduce in commit  2e8ac303
(the first time rdev_set_badblock was call from interrupt context),
so this patch is appropriate for 3.5 and subsequent kernels.

Cc: <stable@vger.kernel.org> (3.5+)
Signed-off-by: Bian Yu <bianyu@kedacom.com>
Reviewed-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>

Since:
        commit 7ceb17e8
        md: Allow devices to be re-added to a read-only array.

spares are activated on a read-only array. In case of raid1 and raid10
personalities it causes that not-in-sync devices are marked in-sync
without checking if recovery has been finished.

If a read-only array is degraded and one of its devices is not in-sync
(because the array has been only partially recovered) recovery will be skipped.

This patch adds checking if recovery has been finished before marking a device
in-sync for raid1 and raid10 personalities. In case of raid5 personality
such condition is already present (at raid5.c:6029).

Bug was introduced in 3.10 and causes data corruption.

Cc: stable@vger.kernel.org
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>

Sujit has found a race condition that would make q->nr_pending
unbalanced, it occurs as Sujit explained:

"
sd_probe_async() ->
	add_disk() ->
		disk_add_event() ->
			schedule(disk_events_workfn)
	sd_revalidate_disk()
	blk_pm_runtime_init()
return;

Let's say the disk_events_workfn() calls sd_check_events() which tries
to send test_unit_ready() and because of sd_revalidate_disk() trying to
send another commands the test_unit_ready() might be re-queued as the
tagged command queuing is disabled.

So the race condition is -

Thread 1 			  |		Thread 2
sd_revalidate_disk()		  |	sd_check_events()
...nr_pending = 0 as q->dev = NULL|	scsi_queue_insert()
blk_runtime_pm_init()		  | 	blk_pm_requeue_request() ->
				  |	nr_pending = -1 since
				  |	q->dev != NULL
"

The problem is, the test_unit_ready request doesn't get counted the
first time it is queued, so the later decrement of q->nr_pending in
blk_pm_requeue_request makes it unbalanced.

Fix this by calling blk_pm_runtime_init before add_disk so that all
requests initiated there will all be counted.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reported-and-tested-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

If an invalid IOCB is returned on the response queue then the index into the
request queue map could be invalid and could return to us a bogus value. This
could cause us to try to deference an invalid pointer and cause an exception.

If we encounter this condition, simply return as no context can be established
for this response.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Pull s390 fixes from Martin Schwidefsky:
 "Several last minute bug fixes.

  Two of them are on the larger side for rc7, the dasd format patch for
  older storage devices and the store-clock-fast patch where we have
  been to optimistic with an optimization"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/time: correct use of store clock fast
  s390/vmlogrdr: fix array access in vmlogrdr_open()
  s390/compat,signal: fix return value of copy_siginfo_(to|from)_user32()
  s390/dasd: check for availability of prefix command during format
  s390/mm,kvm: fix software dirty bits vs. kvm for old machines

Pull thermal management fixes from Zhang Rui:
 "These includes several commits that are necessary to properly fix
  regression for TMU test MUX address setting after reset, for exynos
  thermal driver.

  Specifics:

   - fix a regression that the removal of setting a certain field at TMU
     configuration setting results in immediately shutdown after reset
     on Exynos4412 SoC.

   - revert a patch which tries to link the thermal_zone device and its
     hwmon node but breaks libsensors.

   - fix a deadlock/lockdep warning issue in x86_pkg_temp thermal
     driver, which can be reproduced on a buggy platform only.

   - fix ti-soc-thermal driver to fall back on bandgap reading when
     reading from PCB temperature sensor fails"

* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  Revert "drivers: thermal: parent virtual hwmon with thermal zone"
  drivers: thermal: allow ti-soc-thermal run without pcb zone
  thermal: exynos: Provide initial setting for TMU's test MUX address at Exynos4412
  thermal: exynos: Provide separate TMU data for Exynos4412
  thermal: exynos: Remove check for thermal device pointer at exynos_report_trigger()
  Thermal: x86_pkg_temp: change spin lock

Fix build error in asus_wmi.c when ASUS_WMI=y and ACPI_VIDEO=m
by preventing that combination.

  drivers/built-in.o: In function `asus_wmi_probe':
  asus-wmi.c:(.text+0x65ddb4): undefined reference to `acpi_video_unregister'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull media fixes from Mauro Carvalho Chehab:
 - Compilation fixes for GCC < 4.4.6
 - one Kbuild dependency select fix (selecting videobuf on msi3101)
 - driver fixes on tda10071, e4000, msi3101, soc_camera, s5p-jpeg,
   saa7134 and adv7511
 - some device quirks needed to make them work properly
 - some videobuf2 core regression fixes for some features used only on
   embedded drivers

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] saa7134: Fix crash when device is closed before streamoff
  [media] adv7511: fix error return code in adv7511_probe()
  [media] ths8200: fix compilation with GCC < 4.4.6
  [media] ad9389b: fix compilation with GCC < 4.4.6
  [media] adv7511: fix compilation with GCC < 4.4.6
  [media] adv7842: fix compilation with GCC < 4.4.6
  [media] s5p-jpeg: Initialize vfd_decoder->vfl_dir field
  [media] videobuf2-dc: Fix support for mappings without struct page in userptr mode
  [media] vb2: Allow queuing OUTPUT buffers with zeroed 'bytesused'
  [media] mx3-camera: locking cleanup in mx3_videobuf_queue()
  [media] sh_vou: almost forever loop in sh_vou_try_fmt_vid_out()
  [media] tda10071: change firmware download condition
  [media] msi3101: correct max videobuf2 alloc
  [media] Add HCL T12Rg-H to STK webcam upside-down table
  [media] msi3101: Kconfig select VIDEOBUF2_VMALLOC
  [media] msi3101: msi3101_ioctl_ops can be static
  [media] e4000: fix PLL calc bug on 32-bit arch
  [media] uvcvideo: quirk PROBE_DEF for Microsoft Lifecam NX-3000
  [media] uvcvideo: quirk PROBE_DEF for Dell SP2008WFP monitor

Pull infiniband bugfix from Roland Dreier:
 "Disable not-quite-ready userspace ABI for IB flow steering"

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/core: Temporarily disable create_flow/destroy_flow uverbs

Pull networking fixes from David Miller:
 "Sorry I let so much accumulate, I was in Buffalo and wanted a few
  things to cook in my tree for a while before sending to you.  Anyways,
  it's a lot of little things as usual at this stage in the game"

 1) Make bonding MAINTAINERS entry reflect reality, from Andy
    Gospodarek.

 2) Fix accidental sock_put() on timewait mini sockets, from Eric
    Dumazet.

 3) Fix crashes in l2tp due to mis-handling of ipv4 mapped ipv6
    addresses, from François CACHEREUL.

 4) Fix heap overflow in __audit_sockaddr(), from the eagle eyed Dan
    Carpenter.

 5) tcp_shifted_skb() doesn't take handle FINs properly, from Eric
    Dumazet.

 6) SFC driver bug fixes from Ben Hutchings.

 7) Fix TX packet scheduling wedge after channel change in ath9k driver,
    from Felix Fietkau.

 8) Fix user after free in BPF JIT code, from Alexei Starovoitov.

 9) Source address selection test is reversed in
    __ip_route_output_key(), fix from Jiri Benc.

10) VLAN and CAN layer mis-size netlink attributes, from Marc
    Kleine-Budde.

11) Fix permission checks in sysctls to use current_euid() instead of
    current_uid().  From Eric W Biederman.

12) IPSEC policies can go away while a timer is still pending for them,
    add appropriate ref-counting to fix, from Steffen Klassert.

13) Fix mis-programming of FDR and RMCR registers on R8A7740 sh_eth
    chips, from Nguyen Hong Ky and Simon Horman.

14) MLX4 forgets to DMA unmap pages on RX, fix from Amir Vadai.

15) IPV6 GRE tunnel MTU upper limit is miscalculated, from Oussama
    Ghorbel.

16) Fix typo in fq_change(), we were assigning "initial quantum" to
    "quantum".  From Eric Dumazet.

17) Set a more appropriate sk_pacing_rate for non-TCP sockets, otherwise
    FQ packet scheduler does not pace those flows properly.  Also from
    Eric Dumazet.

18) rtlwifi miscalculates packet pointers, from Mark Cave-Ayland.

19) l2tp_xmit_skb() can be called from process context, not just softirq
    context, so we must always make sure to BH disable around it.  From
    Eric Dumazet.

20) On qdisc reset, we forget to purge the RB tree of SKBs in netem
    packet scheduler.  From Stephen Hemminger.

21) Fix info leak in farsync WAN driver ioctl() handler, from Dan
    Carpenter and Salva Peiró.

22) Fix PHY reset and other issues in dm9000 driver, from Nikita
    Kiryanov and Michael Abbott.

23) When hardware can do SCTP crc32 checksums, we accidently don't
    disable the csum offload when IPSEC transformations have been
    applied.  From Fan Du and Vlad Yasevich.

24) Tail loss probing in TCP leaves the socket in the wrong congestion
    avoidance state.  From Yuchung Cheng.

25) In CPSW driver, enable NAPI before interrupts are turned on, from
    Markus Pargmann.

26) Integer underflow and dual-assignment in YAM hamradio driver, from
    Dan Carpenter.

27) If we are going to mangle a packet in tcp_set_skb_tso_segs() we must
    unclone it.  This fixes various hard to track down crashes in
    drivers where the SKBs ->gso_segs was changing right from underneath
    the driver during TX queueing.  From Eric Dumazet.

28) Fix the handling of VLAN IDs, and in particular the special IDs 0
    and 4095, in the bridging layer.  From Toshiaki Makita.

29) Another info leak, this time in wanxl WAN driver, from Salva Peiró.

30) Fix race in socket credential passing, from Daniel Borkmann.

31) WHen NETLABEL is disabled, we don't validate CIPSO packets properly,
    from Seif Mazareeb.

32) Fix identification of fragmented frames in ipv4/ipv6 UDP
    Fragmentation Offload output paths, from Jiri Pirko.

33) Virtual Function fixes in bnx2x driver from Yuval Mintz and Ariel
    Elior.

34) When we removed the explicit neighbour pointer from ipv6 routes a
    slight regression was introduced for users such as IPVS, xt_TEE, and
    raw sockets.  We mix up the users requested destination address with
    the routes assigned nexthop/gateway.  From Julian Anastasov and
    Simon Horman.

35) Fix stack overruns in rt6_probe(), the issue is that can end up
    doing two full packet xmit paths at the same time when emitting
    neighbour discovery messages.  From Hannes Frederic Sowa.

36) davinci_emac driver doesn't handle IFF_ALLMULTI correctly, from
    Mariusz Ceier.

37) Make sure to set TCP sk_pacing_rate after the first legitimate RTT
    sample, from Neal Cardwell.

38) Wrong netlink attribute passed to xfrm_replay_verify_len(), from
    Steffen Klassert.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (152 commits)
  ax88179_178a: Add VID:DID for Samsung USB Ethernet Adapter
  ax88179_178a: Correct the RX error definition in RX header
  Revert "bridge: only expire the mdb entry when query is received"
  tcp: initialize passive-side sk_pacing_rate after 3WHS
  davinci_emac.c: Fix IFF_ALLMULTI setup
  mac802154: correct a typo in ieee802154_alloc_device() prototype
  ipv6: probe routes asynchronous in rt6_probe
  netfilter: nf_conntrack: fix rt6i_gateway checks for H.323 helper
  ipv6: fill rt6i_gateway with nexthop address
  ipv6: always prefer rt6i_gateway if present
  bnx2x: Set NETIF_F_HIGHDMA unconditionally
  bnx2x: Don't pretend during register dump
  bnx2x: Lock DMAE when used by statistic flow
  bnx2x: Prevent null pointer dereference on error flow
  bnx2x: Fix config when SR-IOV and iSCSI are enabled
  bnx2x: Fix Coalescing configuration
  bnx2x: Unlock VF-PF channel on MAC/VLAN config error
  bnx2x: Prevent an illegal pointer dereference during panic
  bnx2x: Fix Maximum CoS estimation for VFs
  drivers: net: cpsw: fix kernel warn during iperf test with interrupt pacing
  ...

Add VID:DID for Samsung USB Ethernet Adapter.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>

Correct the definition of AX_RXHDR_CRC_ERR and
AX_RXHDR_DROP_ERR. They are BIT29 and BIT31 in pkt_hdr
seperately.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>

While this commit was a good attempt to fix issues occuring when no
multicast querier is present, this commit still has two more issues:

1) There are cases where mdb entries do not expire even if there is a
querier present. The bridge will unnecessarily continue flooding
multicast packets on the according ports.

2) Never removing an mdb entry could be exploited for a Denial of
Service by an attacker on the local link, slowly, but steadily eating up
all memory.

Actually, this commit became obsolete with
"bridge: disable snooping if there is no querier" (b00589af)
which included fixes for a few more cases.

Therefore reverting the following commits (the commit stated in the
commit message plus three of its follow up fixes):

====================
Revert "bridge: update mdb expiration timer upon reports."
This reverts commit f144febd.
Revert "bridge: do not call setup_timer() multiple times"
This reverts commit 1faabf2a.
Revert "bridge: fix some kernel warning in multicast timer"
This reverts commit c7e8e8a8.
Revert "bridge: only expire the mdb entry when query is received"
This reverts commit 9f00b2e7.
====================

CC: Cong Wang <amwang@redhat.com>
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Reviewed-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not touch keyboard backlight unless explicitly passed a module
parameter.  In this way we won't make wrong assumptions about what are
good default values since they actually are different from model to
model.

The only side effect is that we won't know what is the current value
until set via the sysfs attributes.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Move kernel-doc notation to immediately before its function to eliminate
kernel-doc warnings introduced by commit db14fc3a ("vfs: add
d_walk()")

  Warning(fs/dcache.c:1343): No description found for parameter 'data'
  Warning(fs/dcache.c:1343): No description found for parameter 'dentry'
  Warning(fs/dcache.c:1343): Excess function parameter 'parent' description in 'check_mount'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Miklos Szeredi <mszeredi@suse.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add @path parameter to fix kernel-doc warning.
Also fix a spello/typo.

  Warning(fs/namei.c:2304): No description found for parameter 'path'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull sound fixes from Takashi Iwai:
 "The pending last-minute ASoC fixes, all of which are driver-local
  (tlv320aic3x, rcar, pcm1681, pcm1792a, omap, fsl) and should be pretty
  safe to apply"

* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: Add MAINTAINERS entry for dmaengine helpers
  ASoC: pcm1792a: Fix max_register setting
  ASoC: pcm1681: Fix max_register setting
  ASoC: pcm1681: Fix max_register setting
  ASoC: rcar: fixup generation checker
  ASoC: tlv320aic3x: Connect 'Left Line1R Mux' and 'Right Line1L Mux'
  ASoC: fsl: imx-ssi: fix probe on imx31
  ASoC: omap: Fix incorrect ARM dependency
  ASoC: fsl: Fix sound on mx31moboard
  ASoC: fsl_ssi: Fix irq_of_parse_and_map() return value check

Pull jfs bugfix from David Kleikamp:
 "Just a patch to fix an oops in an error path"

* tag 'jfs-3.12' of git://github.com/kleikamp/linux-shaggy:
  jfs: fix error path in ialloc

Pull drm fixes from Dave Airlie:
 "Travelling slowed down getting these out.

  Two vmwgfx fixes, a radeon revert to avoid a regression, i915 fixes,
  and some ioctl sizing issues fixed with 32 on 64"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon/audio: don't set speaker allocation on DCE4+
  drm/radeon: rework audio option
  drm/radeon/audio: don't set speaker allocation on DCE3.2
  drm/radeon: make missing smc ucode non-fatal (CI)
  drm/radeon: make missing smc ucode non-fatal (r7xx-SI)
  drm/radeon/uvd: revert lower msg&fb buffer requirements on UVD3
  drm/radeon: stop the leaks in cik_ib_test
  drm/radeon/atom: workaround vbios bug in transmitter table on rs780
  drm/i915: Disable GGTT PTEs on GEN6+ suspend
  drm/i915: Make PTE valid encoding optional
  drm: Pad drm_mode_get_connector to 64-bit boundary
  drm: Prevent overwriting from userspace underallocating core ioctl structs
  drm/vmwgfx: Don't kill clients on VT switch
  drm/vmwgfx: Don't put resources with invalid id's on lru list
  drm/i915: disable LVDS clock gating on CPT v2

Pull HID fixes from Jiri Kosina:

 - a partial revert of exponent parsing changes to make "Unit" exponent
   item work properly again, by Nikolai Kondrashov

 - a few new device IDs additions piggy-backing, by AceLan Kao and David
   Herrmann

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: wiimote: add LEGO-wiimote VID
  HID: Fix unit exponent parsing again
  HID: usbhid: quirk for SiS Touchscreen
  HID: usbhid: quirk for Synaptics Large Touchccreen

Pull libata fixes from Tejun Heo:
 "The only interesting bit is ata_eh_qc_retry() update which fixes a
  problem where a SG_IO command may fail across suspend/resume cycle
  without the command actually being at fault.

  Other changes are low level driver specific and fairly low impact"

* 'for-3.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  libahci: fix turning on LEDs in ahci_start_port()
  libata: make ata_eh_qc_retry() bump scmd->allowed on bogus failures
  ahci_platform: use dev_info() instead of printk()
  ahci: use dev_info() instead of printk()
  pata_isapnp: Don't use invalid I/O ports

Pull cgroup fixes from Tejun Heo:
 "Two late fixes for cgroup.

  One fixes descendant walk introduced during this rc1 cycle.  The other
  fixes a post 3.9 bug during task attach which can lead to hang.  Both
  fixes are critical and the fixes are relatively straight-forward"

* 'for-3.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: fix to break the while loop in cgroup_attach_task() correctly
  cgroup: fix cgroup post-order descendant walk of empty subtree

The result of the store-clock-fast (STCKF) instruction is a bit fuzzy.
It can happen that the value stored on one CPU is smaller than the value
stored on another CPU, although the order of the stores is the other
way around. This can cause deltas of get_tod_clock() values to become
negative when they should not be.

We need to be more careful with store-clock-fast, this patch partially
reverts git commit e4b7b4238e666682555461fa52eecd74652f36bb "time:
always use stckf instead of stck if available". The get_tod_clock()
function now uses the store-clock-extended (STCKE) instruction.
get_tod_clock_fast() can be used if the fuzziness of store-clock-fast
is acceptable e.g. for wait loops local to a CPU.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>