- 16 Mar, 2015 4 commits
-
-
Priit Laes authored
Signed-off-by:
Priit Laes <plaes@plaes.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Zefir Kurtisi authored
Signed-off-by:
Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by:
-
Zefir Kurtisi authored
In HT40 modes, pulse events on primary and extension channel are processed individually. If valid, a pulse event will be fed into the detector * for primary frequency, or * for extension frequency (+/-20MHz based on HT40-mode) * or both With that, a 40MHz radar will result in two individual radar events. Signed-off-by:
-
Zefir Kurtisi authored
To support HT40 DFS mode, a triggering detector must reset only itself but not other detector lines. Signed-off-by:
-
- 13 Mar, 2015 36 commits
-
-
Rafał Miłecki authored
This reverts commit b09f5ec1. Now that we have fully working BCMA_DRIVER_PCI symbol (in can be safely disabled), there is no risk bcma will try to use PCI code without PCI available. Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
Rafał Miłecki authored
It isn't required for bcma bus on SoCs, so provide some empty functions and allow disabling it. Signed-off-by:
-
Rafał Miłecki authored
This function isn't really related to any bus core. It touches PCI device config registers only, so move it to the (PCI) host file. Signed-off-by:
-
Taehee Yoo authored
Remove unnecessary parameter in rtl8192cu/hw.c Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Signed-off-by:
-
Julia Lawall authored
The semantic patch that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r@ type T; identifier f; @@ static T f (...) { ... } @@ identifier r.f; declarer name EXPORT_SYMBOL_GPL; @@ -EXPORT_SYMBOL_GPL(f); // </smpl> Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
Arend van Spriel authored
The watchdog timer is used to put the device in a low-power mode when it is idle for some time. This timer is stopped during that mode and should be restarted upon activity. This has been broken by commit d4150fced0365 ("brcmfmac: Simplify watchdog sleep."). This patch restores the behaviour as it was before that commit. Reported-by:Pontus Fuchs <pontusf@broadcom.com> Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
Arend van Spriel authored
The firmware provides pointer to SDIO shared information at end of RAM during firmware initialization. End of RAM is obviously determined by the actual ram size, but part of that may be used for save&restore memory. In that case another location in RAM will hold the pointer. Reviewed-by:
-
Arend van Spriel authored
Instead of hard-coded memory sizes it is possible to obtain that information from the internal memory registers. Reviewed-by:
Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by:
-
Arend van Spriel authored
Make the brcmf_chip_attach() function responsible for putting the device in a state where it is accessible for firmware download. Reviewed-by:
-
Arend van Spriel authored
The functions brcmf_chip_[enter/exit]_download() are not exclusively used for firmware download so rename these more appropriate. Reviewed-by:
-
Arend van Spriel authored
Instead of checking the cores in the chip only if CONFIG_BRCMDBG is selected perform the check always and extend it with more sanity checking. Reviewed-by:
-
Arend van Spriel authored
Removing the ramsize from the brcmf_sdio structure to avoid duplication. The information is available in brcmf_chip structure. Reviewed-by:
-
Florian Westphal authored
pre-requisite to shrink size of ieee80211_tx_info which in turn is needed to shrink skb->cb to 40 bytes again. Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
-
Florian Westphal authored
If we want to shrink skb->cb then we'd have to see about reducing struct ieee80211_tx_info, which gets embedded inside skb->cb[]. It provides a scratch space to be used by wireless drivers. ar5523 uses the maximum space available today (40 bytes), but it seems we don't need this -- data->skb pointer seems to always point back to the skb whose cb buffer the data structure resides, iow, given a pointer to the embedded control buffer we can infer the skb address. Tested-by:
Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by:
-
Sujith Manoharan authored
Since the RTT registers need to be configured for all valid chains irrespective of the runtime chainmask, use the actual chainmask of the chip. Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
-
Sujith Manoharan authored
When assigning the initvals for PCIE sleep/awake registers, check the configuration that has been assigned to pll_pwrsave during initialization. Also, display a warning if we don't have valid arrays. Signed-off-by:
-
Sujith Manoharan authored
Cards based on AR9462/AR9565 support more PCIE power save mechanisms, so register them correctly. Signed-off-by:
-
Sujith Manoharan authored
Use the value in ah->config.pll_pwrsave to determine which array needs to be loaded. Also, initialize pll_pwrsave to 1 by default. Signed-off-by:
-
Sujith Manoharan authored
These will be used to handle chip-specific power save configuration. Signed-off-by:
-
Vladimir Kondratiev authored
For the AP, configuration may say not to bridge traffic between wireless clients. This is conveyed from user space (ex: hostapd has ap_isolate parameter) with NL80211_CMD_SET_BSS, to the driver's cfg80211 ops method change_bss Add support for this setting. Signed-off-by:
Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by:
-
Vladimir Kondratiev authored
This is for AP only. If Rx data frame targeted to one of associated clients, transmit it back to the wireless media and don't deliver to the host. For the multicast frames, deliver to both host and wireless media. Signed-off-by:
-
Vladimir Kondratiev authored
It is expected that driver completes NAPI when less than full budget is consumed. Fulfill this requirement. Signed-off-by:
-
Syed Asifful Dayyan authored
These changes add support for BCM4345 SDIO chipset. Reviewed-by:
Daniel (Deognyoun) Kim <dekim@broadcom.com> Signed-off-by:
Syed Asifful Dayyan <syedd@broadcom.com> Signed-off-by:
-
Hante Meuleman authored
Msgbuf is using a wait_event_timeout to wait for the response on an ioctl. The wakeup routine uses waitqueue_active to see if wait_event_timeout has been called. There is a chance that the response arrives before wait_event_timeout is called, this will result in situation that wait_event_timeout never gets woken again and assumed result will be a timeout. This patch removes that errornous situation by always setting the ctl_completed var before checking for queue active. Reviewed-by:
-
Hante Meuleman authored
SDIO is using a "shared" variable to handoff ctl frames to DPC and to see when they are done. In a timeout situation this can lead to erroneous situation where DPC started to handle the ctl frame while the timeout expired. This patch will fix this by adding locking around the shared variable. Reviewed-by:
-
Hante Meuleman authored
The watchdog thread is used to put the SDIO bus to sleep when the system is idling. This patch simplifies the way it is determined when sleep can be entered. Reviewed-by:
-
Hante Meuleman authored
On removal of SDIO card both functions of card will be getting a remove call. When the first is hanging in ctrl frame xmit then the second will cause oops. This patch fixes the xmit ctrl handling in case of serious errors and also limits the handling for remove to function 1 only. Reviewed-by:
-
Taehee Yoo authored
Remove duplicated prototype in base.h Signed-off-by:
-
Sergey Ryazanov authored
To prepare for reset ath5k should finish all asynchronous tasks. At first, it disables the interrupt generation, then it waits for the interrupt handler and tasklets completion, and then proceeds to the HW configuration update. But it does not consider that the interrupt handler or tasklet re-enables the interrupt generation. And we fall in a situation when ath5k assumes that interrupts are disabled, but it is not. This can lead to different consequences, such as reception of the frame, when we do not expect it. Under certain circumstances, this can lead to the following warning: WARNING: at ath5k/base.c:589 ath5k_tasklet_rx+0x318/0x6ec [ath5k]() invalid hw_rix: 1a [..] Call Trace: [<802656a8>] show_stack+0x48/0x70 [<802dd92c>] warn_slowpath_common+0x88/0xbc [<802dd98c>] warn_slowpath_fmt+0x2c/0x38 [<81b51be8>] ath5k_tasklet_rx+0x318/0x6ec [ath5k] [<8028ac64>] tasklet_action+0x8c/0xf0 [<80075804>] __do_softirq+0x180/0x32c [<80196ce8>] irq_exit+0x54/0x70 [<80041848>] ret_from_irq+0x0/0x4 [<80182fdc>] ioread32+0x4/0xc [<81b4c42c>] ath5k_hw_set_sleep_clock+0x2ec/0x474 [ath5k] [<81b4cf28>] ath5k_hw_reset+0x50/0xeb8 [ath5k] [<81b50900>] ath5k_reset+0xd4/0x310 [ath5k] [<81b557e8>] ath5k_config+0x4c/0x104 [ath5k] [<80d01770>] ieee80211_hw_config+0x2f4/0x35c [mac80211] [<80d09aa8>] ieee80211_scan_work+0x2e4/0x414 [mac80211] [<8022c3f4>] process_one_work+0x28c/0x400 [<802df8f8>] worker_thread+0x258/0x3c0 [<801b5710>] kthread+0xe0/0xec [<800418a8>] ret_from_kernel_thread+0x14/0x1c Fix this issue by adding a new status flag, which forbids to re-enable the interrupt generation until the HW configuration is completed. Note: previous patch, which reorders the Rx disable code helps to avoid the above warning, but not fixes the root cause of unexpected frame receiving. CC: Jiri Slaby <jirislaby@gmail.com> CC: Nick Kossifidis <mickflemm@gmail.com> CC: Luis R. Rodriguez <mcgrof@do-not-panic.com> Reported-by:
Christophe Prevotaux <cprevotaux@nltinc.com> Tested-by:
Eric Bree <ebree@nltinc.com> Signed-off-by:
Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by:
-
Sergey Ryazanov authored
ath5k updates the channel pointer and after that it stops the Rx logic and apply channel to HW. In case of channel switch, such sequence creates a small window when a frame, which is received on the old channel is considered as a frame received on the new one. The most notable consequence of this situation occurs during the switch from 2 GHz band (CCK+OFDM) to the 5GHz band (OFDM-only). Frame received with CCK rate, e.g. beacon received at the 1mbps, causes the following warning: WARNING: at ath5k/base.c:589 ath5k_tasklet_rx+0x318/0x6ec [ath5k]() invalid hw_rix: 1a [..] Call Trace: [<802656a8>] show_stack+0x48/0x70 [<802dd92c>] warn_slowpath_common+0x88/0xbc [<802dd98c>] warn_slowpath_fmt+0x2c/0x38 [<81b51be8>] ath5k_tasklet_rx+0x318/0x6ec [ath5k] [<8028ac64>] tasklet_action+0x8c/0xf0 [<80075804>] __do_softirq+0x180/0x32c [<80196ce8>] irq_exit+0x54/0x70 [<80041848>] ret_from_irq+0x0/0x4 [<80182fdc>] ioread32+0x4/0xc [<81b4c42c>] ath5k_hw_set_sleep_clock+0x2ec/0x474 [ath5k] [<81b4cf28>] ath5k_hw_reset+0x50/0xeb8 [ath5k] [<81b50900>] ath5k_reset+0xd4/0x310 [ath5k] [<81b557e8>] ath5k_config+0x4c/0x104 [ath5k] [<80d01770>] ieee80211_hw_config+0x2f4/0x35c [mac80211] [<80d09aa8>] ieee80211_scan_work+0x2e4/0x414 [mac80211] [<8022c3f4>] process_one_work+0x28c/0x400 [<802df8f8>] worker_thread+0x258/0x3c0 [<801b5710>] kthread+0xe0/0xec [<800418a8>] ret_from_kernel_thread+0x14/0x1c The easiest way to reproduce this warning is to run scan with dualband NIC in noisy environments, when the channel 11 runs multiple APs. In my tests if the APs num >= 12, the warning appears in the first few seconds of scanning. In order to fix this, the Rx disable code moved to a higher level and placed before the channel pointer update. This is also makes the code a bit more symmetrical, since we disable and enable the Rx in the same function. In fact, at the pointer update time new frames should not appear, because interrupt generation at this point should already be disabled. The next patch should address this issue. CC: Jiri Slaby <jirislaby@gmail.com> CC: Nick Kossifidis <mickflemm@gmail.com> CC: Luis R. Rodriguez <mcgrof@do-not-panic.com> Reported-by:
-
Kalle Valo authored
Merge tag 'iwlwifi-next-for-kalle-2015-03-12' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next * Location Aware Regulatory was added by Arik * 8000 device family work * Update to the BT Coex firmware API
-
Simon Horman authored
In the case of AF_INET s_addr was set to INADDR_ANY (0) which which both symmetric with the AF_INET6 case, where s_addr is not set, and unnecessary as udp_conf is zeroed out earlier in the same function. I suspect this change does not have any run-time effect due to compiler optimisations. But it does make the code a little easier on the/my eyes. Cc: Tom Herbert <therbert@google.com> Signed-off-by:
Simon Horman <simon.horman@netronome.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric W. Biederman authored
Reobert Shearman noticed that mpls_egress is failing to verify that the bytes to be examined are in fact present in the packet before mpls_egress reads those bytes. As suggested by David Miller reduce this to a single pskb_may_pull call so that we don't do unnecessary work in the fast path. Reported-by:
Robert Shearman <rshearma@brocade.com> Signed-off-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Jaeden Amero authored
The PHY state machine (in drivers/net/phy/phy.c) will unconditionally call phydev->adjust_link (macb_handle_link_change) when polling in the PHY_CHANGELINK state. As currently written, macb always ends up requesting a new tx_clk frequency in macb_handle_link_change. It is a waste of time to request a new tx_clk frequency if the link state hasn't changed, as the tx_clk will already be configured properly. Let's only request a new tx_clk clock frequency when necessary. Signed-off-by:
Jaeden Amero <jaeden.amero@ni.com> Cc: Josh Cartwright <joshc@ni.com> Cc: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by:
-
Herbert Xu authored
This patch fixes a typo rhashtable_lookup_compare where we fail to recompute the hash when looking up the new table. This causes elements to be missed and potentially a crash during a resize. Reported-by:
Thomas Graf <tgraf@suug.ch> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Daniel Borkmann authored
Commit c0c09bfd ("rhashtable: avoid unnecessary wakeup for worker queue") changed ht->shift to be atomic, which is actually unnecessary. Instead of leaving the current shift in the core rhashtable structure, it can be cached inside the individual bucket tables. There, it will only be initialized once during a new table allocation in the shrink/expansion slow path, and from then onward it stays immutable for the rest of the bucket table liftime. That allows shift to be non-atomic. The patch also moves hash_rnd management into the table setup. The rhashtable structure now consumes 3 instead of 4 cachelines. Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Cc: Ying Xue <ying.xue@windriver.com> Acked-by:
-
