This patch adds the ability for a VSI to use multiple Tx queues. More
specifically, the patch
    1) Provides the ability to update the Tx scheduler tree in the
       firmware. The driver can configure the Tx scheduler tree by
       adding/removing multiple Tx queues per TC per VSI.

    2) Allows a VSI to reconfigure its Tx queues during runtime.

    3) Synchronizes the Tx scheduler update operations using locks.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements a watchdog task to get packet statistics from
the device.

This patch also adds support for the following ethtool operations:

ethtool devname
ethtool -s devname [msglvl N] [msglevel type on|off]
ethtool -g|--show-ring devname
ethtool -G|--set-ring devname [rx N] [tx N]
ethtool -i|--driver devname
ethtool -d|--register-dump devname [raw on|off] [hex on|off] [file name]
ethtool -k|--show-features|--show-offload devname
ethtool -K|--features|--offload devname feature on|off
ethtool -P|--show-permaddr devname
ethtool -S|--statistics devname
ethtool -a|--show-pause devname
ethtool -A|--pause devname [autoneg on|off] [rx on|off] [tx on|off]
ethtool -r|--negotiate devname

CC: Andrew Lunn <andrew@lunn.ch>
CC: Jakub Kicinski <kubakici@wp.pl>
CC: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for VLANs. When a VLAN is created a switch filter
is added to direct the VLAN traffic to the corresponding VSI. When a VLAN
is deleted, the filter is deleted as well.

This patch also adds support for the following hardware offloads.
    1) VLAN tag insertion/stripping
    2) Receive Side Scaling (RSS)
    3) Tx checksum and TCP segmentation
    4) Rx checksum
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements ice_start_xmit (the handler for ndo_start_xmit) and
related functions. ice_start_xmit ultimately calls ice_tx_map, where the
Tx descriptor is built and posted to the hardware by bumping the ring tail.

This patch also implements ice_napi_poll, which is invoked when there's an
interrupt on the VSI's queues. The interrupt can be due to either a
completed Tx or an Rx event. In case of a completed Tx/Rx event, resources
are reclaimed. Additionally, in case of an Rx event, the skb is fetched
and passed up to the network stack.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch configures the VSIs to be able to send and receive
packets by doing the following:

1) Initialize flexible parser to extract and include certain
   fields in the Rx descriptor.

2) Add Tx queues by programming the Tx queue context (implemented in
   ice_vsi_cfg_txqs). Note that adding the queues also enables (starts)
   the queues.

3) Add Rx queues by programming Rx queue context (implemented in
   ice_vsi_cfg_rxqs). Note that this only adds queues but doesn't start
   them. The rings will be started by calling ice_vsi_start_rx_rings on
   interface up.

4) Configure interrupts for VSI queues.

5) Implement ice_open and ice_stop.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

A VSI needs traffic directed towards it. This is done by programming
filter rules on the switch (embedded vSwitch) element in the hardware,
which connects the VSI to the ingress/egress port.

This patch introduces data structures and functions necessary to add
remove or update switch rules on the switch element. This is a pretty low
level function that is generic enough to add a whole range of filters.

This patch also introduces two top level functions ice_add_mac and
ice_remove mac which through a series of intermediate helper functions
eventually call ice_aq_sw_rules to add/delete simple MAC based filters.
It's worth noting that one invocation of ice_add_mac/ice_remove_mac
is capable of adding/deleting multiple MAC filters.

Also worth noting is the fact that the driver maintains a list of currently
active filters, so every filter addition/removal causes an update to this
list. This is done for a couple of reasons:

1) If two VSIs try to add the same filters, we need to detect it and do
   things a little differently (i.e. use VSI lists, described below) as
   the same filter can't be added more than once.

2) In the event of a hardware reset we can simply walk through this list
   and restore the filters.

VSI Lists:
In a multi-VSI situation, it's possible that multiple VSIs want to add the
same filter rule. For example, two VSIs that want to receive broadcast
traffic would both add a filter for destination MAC ff:ff:ff:ff:ff:ff.
This can become cumbersome to maintain and so this is handled using a
VSI list.

A VSI list is resource that can be allocated in the hardware using the
ice_aq_alloc_free_res admin queue command. Simply put, a VSI list can
be thought of as a subscription list containing a set of VSIs to which
the packet should be forwarded, should the filter match.

For example, if VSI-0 has already added a broadcast filter, and VSI-1
wants to do the same thing, the filter creation flow will detect this,
allocate a VSI list and update the switch rule so that broadcast traffic
will now be forwarded to the VSI list which contains VSI-0 and VSI-1.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch introduces data structures and functions to alloc/free
VSIs. The driver represents a VSI using the ice_vsi structure.

Some noteworthy points about VSI allocation:

1) A VSI is allocated in the firmware using the "add VSI" admin queue
   command (implemented as ice_aq_add_vsi). The firmware returns an
   identifier for the allocated VSI. The VSI context is used to program
   certain aspects (loopback, queue map, etc.) of the VSI's configuration.

2) A VSI is deleted using the "free VSI" admin queue command (implemented
   as ice_aq_free_vsi).

3) The driver represents a VSI using struct ice_vsi. This is allocated
   and initialized as part of the ice_vsi_alloc flow, and deallocated
   as part of the ice_vsi_delete flow.

4) Once the VSI is created, a netdev is allocated and associated with it.
   The VSI's ring and vector related data structures are also allocated
   and initialized.

5) A VSI's queues can either be contiguous or scattered. To do this, the
   driver maintains a bitmap (vsi->avail_txqs) which is kept in sync with
   the firmware's VSI queue allocation imap. If the VSI can't get a
   contiguous queue allocation, it will fallback to scatter. This is
   implemented in ice_vsi_get_qs which is called as part of the VSI setup
   flow. In the release flow, the VSI's queues are released and the bitmap
   is updated to reflect this by ice_vsi_put_qs.

CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch continues the initialization flow as follows:

1) Allocate and initialize necessary fields (like vsi, num_alloc_vsi,
   irq_tracker, etc) in the ice_pf instance.

2) Setup the miscellaneous interrupt handler. This also known as the
   "other interrupt causes" (OIC) handler and is used to handle non
   hotpath interrupts (like control queue events, link events,
   exceptions, etc.

3) Implement a background task to process admin queue receive (ARQ)
   events received by the driver.

CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds code to continue the initialization flow as follows:

1) Get PHY/link information and store it
2) Get default scheduler tree topology and store it
3) Get the MAC address associated with the port and store it
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds to the initialization flow by getting switch
configuration, scheduler configuration and device capabilities.

Switch configuration:
On boot, an L2 switch element is created in the firmware per physical
function. Each physical function is also mapped to a port, to which its
switch element is connected. In other words, this switch can be visualized
as an embedded vSwitch that can connect a physical function's virtual
station interfaces (VSIs) to the egress/ingress port. Egress/ingress
filters will be eventually created and applied on this switch element.
As part of the initialization flow, the driver gets configuration data
from this switch element and stores it.

Scheduler configuration:
The Tx scheduler is a subsystem responsible for setting and enforcing QoS.
As part of the initialization flow, the driver queries and stores the
default scheduler configuration for the given physical function.

Device capabilities:
As part of initialization, the driver has to determine what the device is
capable of (ex. max queues, VSIs, etc). This information is obtained from
the firmware and stored by the driver.

CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements multiple pieces of the initialization flow
as follows:

1) A reset is issued to ensure a clean device state, followed
   by initialization of admin queue interface.

2) Once the admin queue interface is up, clear the PF config
   and transition the device to non-PXE mode.

3) Get the NVM configuration stored in the device's non-volatile
   memory (NVM) using ice_init_nvm.

CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

A control queue is a hardware interface which is used by the driver
to interact with other subsystems (like firmware, PHY, etc.). It is
implemented as a producer-consumer ring. More specifically, an
"admin queue" is a type of control queue used to interact with the
firmware.

This patch introduces data structures and functions to initialize
and teardown control/admin queues. Once the admin queue is initialized,
the driver uses it to get the firmware version.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a basic driver framework for the Intel(R) E800 Ethernet
Series of network devices. There is no functionality right now other than
the ability to load.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Merge tag 'wireless-drivers-next-for-davem-2018-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.17

The biggest changes are the bluetooth related patches to the rsi
driver. It adds a new bluetooth driver which communicates directly
with the wireless driver and the interface is defined in
include/net/rsi_91x.h.

Major changes:

wl1251

* read the MAC address from the NVS file

rtlwifi

* enable mac80211 fast-tx support

mt76

* add capability to select tx/rx antennas

mt7601

* let mac80211 validate rx CCMP Packet Number (PN)

rsi

* bluetooth: add new btrsi driver

* btcoex support with the new btrsi driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes: 25b0b9c4 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Jon Maloy jon.maloy@ericsson.com
Signed-off-by: David S. Miller <davem@davemloft.net>

There is an && vs || typo here, which potentially leads to a NULL
dereference.

Fixes: e9e1e978 ("ibmvnic: Update TX pool cleaning routine")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for new 32MB and 64MB ISSI (Integrated Silicon
Solution, Inc.) FLASH parts.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Depend on the firmware sending us link status changes,
rather than assuming that the link goes down upon L1
configuration.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Copy vlan_id to get it displayed in vf info.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudhar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When NetworkManager is enabled, there are chances that interface up
is called even before probe completes. This means we have not yet
allocated the FW sge queues, hence rest of ingress queue allocation
wont be proper. Fix this by calling setup_fw_sge_queues() before
register_netdev().

Fixes: 0fbc81b3 ('chcr/cxgb4i/cxgbit/RDMA/cxgb4: Allocate resources dynamically for all cxgb4 ULD's')
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: broadcom: Adaptive interrupt coalescing

This patch series adds adaptive interrupt coalescing for the Gigabit Ethernet
drivers SYSTEMPORT and GENET.

This really helps lower the interrupt count and system load, as measured by
vmstat for a Gigabit TCP RX session:

SYSTEMPORT:

without:

 1  0      0 192188      0  25472    0    0     0     0 122100 38870  1 42 57  0  0
[ ID] Interval       Transfer     Bandwidth
[  4]  0.0-10.0 sec  1.03 GBytes   884 Mbits/sec

with:

 1  0      0 192288      0  25468    0    0     0     0 58806 44401  0 100  0  0  0
[  5]  0.0-10.0 sec  1.04 GBytes   888 Mbits/sec

GENET:

without:

 1  0      0 1170404      0  25420    0    0     0     0 130785 63402  2 85 12  0  0
[ ID] Interval       Transfer     Bandwidth
[  4]  0.0-10.0 sec  1.04 GBytes   888 Mbits/sec

with:

 1  0      0 1170560      0  25420    0    0     0     0 50610 48477  0 100  0  0  0
[  5]  0.0-10.0 sec  1.05 GBytes   899 Mbits/sec

Please look at the implementation and let me know if you see any problems, this
was largely inspired by bnxt_en.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Unlike the moder modern SYSTEMPORT hardware, we do not have a
configurable TDMA timeout, which limits us to implement adaptive RX
interrupt coalescing only. We have each of our RX rings implement a
bcmgenet_net_dim structure which holds an interrupt counter, number of
packets, bytes, and a container for a net_dim instance.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement support for adaptive RX and TX interrupt coalescing using
net_dim. We have each of our TX ring and our single RX ring implement a
bcm_sysport_net_dim structure which holds an interrupt counter, number
of packets, bytes, and a container for a net_dim instance.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
Fixes to allow mv88e6xxx module to be reloaded

As reported by Uwe Kleine-König, the interrupt trigger is first
configured by DT and then reconfigured to edge. This results in a
failure on EPROBE_DEFER, or if the module is unloaded and reloaded.

A second crash happens on module reload due to a missing call to the
common IRQ free code when using polled interrupts.

With these fixes in place, it becomes possible to load and unload the
kernel modules a few times without it crashing.

v2: Fix the ü in Künig a couple of times
v3: But the ü should be an ö!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When free'ing the polled IRQs, call the common irq free code.
Otherwise the interrupts are left registered, and when we come to load
the driver a second time, we get an Opps.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

By calling request_threaded_irq() with the flag IRQF_TRIGGER_FALLING
we override the trigger mode provided in device tree. And the
interrupt is actually active low, which is what all the current device
tree descriptions use.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added extra test cases for control actions (reclassify, pipe etc.),
cookies, max index value and police args sanity check.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Haiyang Zhang says:

====================
hv_netvsc: Fix/improve RX path error handling

Fix the status code returned to the host. Also add range
check for rx packet offset and length.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds range checking for rx packet offset and length.
It may only happen if there is a host side bug.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As defined in hyperv_net.h, the NVSP_STAT_SUCCESS is one not zero.
Some functions returns 0 when it actually means NVSP_STAT_SUCCESS.
This patch fixes them.

In netvsc_receive(), it puts the last RNDIS packet's receive status
for all packets in a vmxferpage which may contain multiple RNDIS
packets.
This patch puts NVSP_STAT_FAIL in the receive completion if one of
the packets in a vmxferpage fails.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yonghong Song says:

====================
net: permit skb_segment on head_frag frag_list skb

One of our in-house projects, bpf-based NAT, hits a kernel BUG_ON at
function skb_segment(), line 3667. The bpf program attaches to
clsact ingress, calls bpf_skb_change_proto to change protocol
from ipv4 to ipv6 or from ipv6 to ipv4, and then calls bpf_redirect
to send the changed packet out.
 ...
    3665                 while (pos < offset + len) {
    3666                         if (i >= nfrags) {
    3667                                 BUG_ON(skb_headlen(list_skb));
 ...

The triggering input skb has the following properties:
    list_skb = skb->frag_list;
    skb->nfrags != NULL && skb_headlen(list_skb) != 0
and skb_segment() is not able to handle a frag_list skb
if its headlen (list_skb->len - list_skb->data_len) is not 0.

Patch #1 provides a simple solution to avoid BUG_ON. If
list_skb->head_frag is true, its page-backed frag will
be processed before the list_skb->frags.
Patch #2 provides a test case in test_bpf module which
constructs a skb and calls skb_segment() directly. The test
case is able to trigger the BUG_ON without Patch #1.

The patch has been tested in the following setup:
  ipv6_host <-> nat_server <-> ipv4_host
where nat_server has a bpf program doing ipv4<->ipv6
translation and forwarding through clsact hook
bpf_skb_change_proto.

Changelog:
v5 -> v6:
  . Added back missed BUG_ON(!nfrags) for zero
    skb_headlen(skb) case, plus a couple of
    cosmetic changes, from Alexander.
v4 -> v5:
  . Replace local variable head_frag with
    a static inline function skb_head_frag_to_page_desc
    which gets the head_frag on-demand. This makes
    code more readable and also does not increase
    the stack size, from Alexander.
  . Remove the "if(nfrags)" guard for skb_orphan_frags
    and skb_zerocopy_clone as I found that they can
    handle zero-frag skb (with non-zero skb_headlen(skb))
    properly.
  . Properly release segment list from skb_segment()
    in the test, from Eric.
v3 -> v4:
  . Remove dynamic memory allocation and use rewinding
    for both index and frag to remove one branch in fast path,
    from Alexander.
  . Fix a bunch of issues in test_bpf skb_segment() test,
    including proper way to allocate skb, proper function
    argument for skb_add_rx_frag and not freeint skb, etc.,
    from Eric.
v2 -> v3:
  . Use starting frag index -1 (instead of 0) to
    special process head_frag before other frags in the skb,
    from Alexander Duyck.
v1 -> v2:
  . Removed never-hit BUG_ON, spotted by Linyu Yuan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Without the previous commit,
"modprobe test_bpf" will have the following errors:
...
[   98.149165] ------------[ cut here ]------------
[   98.159362] kernel BUG at net/core/skbuff.c:3667!
[   98.169756] invalid opcode: 0000 [#1] SMP PTI
[   98.179370] Modules linked in:
[   98.179371]  test_bpf(+)
...
which triggers the bug the previous commit intends to fix.

The skbs are constructed to mimic what mlx5 may generate.
The packet size/header may not mimic real cases in production. But
the processing flow is similar.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of our in-house projects, bpf-based NAT, hits a kernel BUG_ON at
function skb_segment(), line 3667. The bpf program attaches to
clsact ingress, calls bpf_skb_change_proto to change protocol
from ipv4 to ipv6 or from ipv6 to ipv4, and then calls bpf_redirect
to send the changed packet out.

3472 struct sk_buff *skb_segment(struct sk_buff *head_skb,
3473                             netdev_features_t features)
3474 {
3475         struct sk_buff *segs = NULL;
3476         struct sk_buff *tail = NULL;
...
3665                 while (pos < offset + len) {
3666                         if (i >= nfrags) {
3667                                 BUG_ON(skb_headlen(list_skb));
3668
3669                                 i = 0;
3670                                 nfrags = skb_shinfo(list_skb)->nr_frags;
3671                                 frag = skb_shinfo(list_skb)->frags;
3672                                 frag_skb = list_skb;
...

call stack:
...
 #1 [ffff883ffef03558] __crash_kexec at ffffffff8110c525
 #2 [ffff883ffef03620] crash_kexec at ffffffff8110d5cc
 #3 [ffff883ffef03640] oops_end at ffffffff8101d7e7
 #4 [ffff883ffef03668] die at ffffffff8101deb2
 #5 [ffff883ffef03698] do_trap at ffffffff8101a700
 #6 [ffff883ffef036e8] do_error_trap at ffffffff8101abfe
 #7 [ffff883ffef037a0] do_invalid_op at ffffffff8101acd0
 #8 [ffff883ffef037b0] invalid_op at ffffffff81a00bab
    [exception RIP: skb_segment+3044]
    RIP: ffffffff817e4dd4  RSP: ffff883ffef03860  RFLAGS: 00010216
    RAX: 0000000000002bf6  RBX: ffff883feb7aaa00  RCX: 0000000000000011
    RDX: ffff883fb87910c0  RSI: 0000000000000011  RDI: ffff883feb7ab500
    RBP: ffff883ffef03928   R8: 0000000000002ce2   R9: 00000000000027da
    R10: 000001ea00000000  R11: 0000000000002d82  R12: ffff883f90a1ee80
    R13: ffff883fb8791120  R14: ffff883feb7abc00  R15: 0000000000002ce2
    ORIG_RAX: ffffffffffffffff  CS: 0010  SS: 0018
 #9 [ffff883ffef03930] tcp_gso_segment at ffffffff818713e7
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2018-03-23

This series contains updates to ixgbe and ixgbevf only.

Paul adds status register reads to reduce a potential race condition
where registers can read 0xFFFFFFFF during a PCI reset, which in turn
causes the driver to remove the adapter.  Then fixes an assignment
operation with an "OR" operation.

Shannon Nelson provides several IPsec offload cleanups to ixgbe, as well as a
patch to enable TSO with IPsec offload.

Tony provides the much anticipated XDP support for ixgbevf.  Currently,
pass, drop and XDP_TX actions are supported, as well as meta data and
stats reporting.

Björn Töpel tweaks the page counting for XDP_REDIRECT, since a page can
have its reference count decreased via the xdp_do_redirect() call.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Intiyaz Basha says:

====================
liquidio: Tx queue cleanup

Moved some common function to octeon_network.h
Removed some unwanted functions and checks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

For consistency renaming txqs_start to start_txqs
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For consistency renaming txqs_stop to stop_txqs
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For consistency renaming txqs_wake to wake_txqs
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using skb_iq function for deriving queue from skb
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removing one line function wake_q
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>