That one seems to have 14-bit ADC resolution, wow!
It is now used when sampling rate is below 6 Msps.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Allow stepless synthesizer configuration. With that change we lose
precision a little bit, as it is now between +-500Hz from the target.
It could be better but on that case calculation algorithm goes more
complex and atm there is more important things to do.
Two approach to improve which comes to my mind are:
1) select and use biggest suitable step
2) use greatest common divisor algo to find divisor for thresh & frac
when possible to avoid rounding errors, which is root of cause of
current +-500Hz inaccuracy.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

No need to compare numbers, we could just store that fractional
value MSB directly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Dump all unknown 'garbage' data - maybe we will discover someday if there
is something rational...
Also fix comment in USB frame description.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

It is based Mirics MSi3101 reference design and will just work
without any changes.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Restarting stream fails quite often. Small delay is between urb killing
and stream stop command - likely to give harware some time to process
killed urbs.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

It looks like there is some extra data carried to enhance sampling
results. When you tune to some some weak/empty channel those bits
are always zeroes. When you tune to some channel where is very
strong signals those bits are all zeroes.
Examining those 32-bits reveals shortly there is 16 pieces of 2-bit
numbers. Number seen are 0, 1 and 3 - for some reason 2 is not used.
I used that number to shift bits given amount to left, "increasing"
sampling resolution by 3-bits. It may be wrong, but after some testing
it still provides better signal.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Whilst Quadrature Sampling is most common sampling technique used in
radio technology there is others too. Add control user could select
sampling mode. We currently support only quadrature sampling.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

These calculations seem to give 100% correct results. Calculation
formulas could be still a little bit wrong as I have no knowledge
what kind of dividers, multipliers and VCO limits there really is.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Just fix wrong term name. No functional changes.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

It is first Kernel software defined radio receiver driver.
That device is sold as a digital television solution.
MSi3101 is reference design which consists of two chips:
1) MSi2500 USB ADC
2) MSi001 RF-tuner
Driver is put to staging as API is not ready.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

changeset d1e9b7c1 added a new ancilliary function to API, but forgot
to add it to the corresponding header file.

drivers/media/v4l2-core/v4l2-ctrls.c:568:18: warning: no previous prototype for 'v4l2_ctrl_get_int_menu' [-Wmissing-prototypes]
 const s64 const *v4l2_ctrl_get_int_menu(u32 id, u32 *len)

Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

drivers/media/platform/soc_camera/sh_mobile_ceu_camera.c: In function 'sh_mobile_ceu_clock_start':
drivers/media/platform/soc_camera/sh_mobile_ceu_camera.c:613:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

When gsc is in runtime suspended state, there is no need to call
m2m_suspend during suspend and similarly, there is no need to call
m2m_resume during resume if already in runtime suspended state. This
patch adds the necessary conditions to achieve this.
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Arun Mankuzhi <arun.m@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

__fimc_is_hw_update_param is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

dev->of_node could be NULL. Hence check for the same and return before
dereferencing it in the subsequent error message.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Resolution set on ISP pad of S5C73M3-OIF subdev should be
propagated to source pad for TRY and ACTIVE formats.
The patch adds missing propagation for TRY format.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

This fixes regression introduced in commit b426b3a6
[media] V4L: Merge struct v4l2_async_subdev_list with struct v4l2_subdev
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Convert the mt9m111 driver to asynchronous subdevice probing. Synchronous
probing is also still possible.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The mt9t031 driver hasn't yet been updated to support asynchronous
subdevice probing. If such a probing is attempted, the driver is allowed
to fail, but it shouldn't Oops. This patch fixes such a potential NULL
pointer dereference.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The soc-camera core does all the work on supporting asynchronous
subdevice probing, host drivers only have to pass a subdevice list to
soc-camera. Typically this list is provided by the platform.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

V4L2_MBUS_FMT_* codes are defined in v4l2-mediabus.h as hexadecimal
constants. Print them in the same form for easier recognition.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Use devm_* resource allocators to simplify the driver's probe and clean up
paths.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

With synchronous subdevice probing regulators should be requested by the
soc-camera core in soc_camera_pdrv_probe(). Subdevice drivers, supporting
asynchronous probing, call soc_camera_power_init() to request regulators.
Erroneously, the same regulator array is used in the latter case as in
the former, which leads to a failure. This patch fixes it by preventing
the second regulator request from being executed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

media_build/v4l/soc_camera.c: In function 'soc_camera_host_register':
media_build/v4l/soc_camera.c:1513:10: warning: 'sasd' may be used uninitialized in this function [-Wmaybe-uninitialized]
  snprintf(clk_name, sizeof(clk_name), "%d-%04x",
          ^
media_build/v4l/soc_camera.c:1464:34: note: 'sasd' was declared here
  struct soc_camera_async_subdev *sasd;
                                  ^
By changing the type of 'i' to unsigned and changing a condition we finally
convince the compiler that sasd is really initialized.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Add Renesas R-Car VIN (Video In) V4L2 driver.
Based on the patch by Phil Edworthy <phil.edworthy@renesas.com>.
[Sergei: removed deprecated IRQF_DISABLED flag, reordered/renamed 'enum chip_id'
values, reordered rcar_vin_id_table[] entries,  removed senseless parens from
to_buf_list() macro, used ALIGN() macro in rcar_vin_setup(), added {} to the
*if* statement  and used 'bool' values instead of 0/1 where necessary, removed
unused macros, done some reformatting and clarified some comments.]
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Calling v4l2_async_notifier_unregister() on a notifier that hasn't been
registered leads to a crash. To simplify drivers, make it safe to
unregister a notifier that has not been registered.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The sample code erroneously scales the y1, pb and pr variables from the
[0.0 .. 1.0] and [-0.5 .. 0.5] ranges to [0 .. 255] and [-128 .. 127].
Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The of_get_child_by_name() function takes a reference to the node it
returns. Make sure to drop it when looking for the ports node in
v4l2_of_get_next_endpoint().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Replace a manual loop through child nodes with a call to
of_get_child_by_name().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

For output buffers application provide to the kernel the number of bytes
they stored in each plane of the buffer. Verify that the value is
smaller than or equal to the plane length.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

changeset 2ccf12af did a crappy job when added multi-line comment lines,
violating CodingStyle.

Change the comments added there to fulfill CodingStyle, and document
the platform_data using Documentation/kernel-doc-nano-HOWTO.txt.

Cc: Jon Arne Jørgensen <jonarne@jonarne.no>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

This patch implements i2c_board_info.platform_data, and some options to
override the default initialization table for the GM7113C and SAA7113
chips.
Signed-off-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Most of the registers changed in saa7115_init_misc table are out of range
for the gm7113c chip.
The only register that's within range, don't need to be changed here.
Signed-off-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

saa711x_set_v4lstd would toggle several bits that should not be touched
when changing std. This patch fixes this.
Signed-off-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Simplify the code by using the new dv_timings helpers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Use the new blanking and frame size defines. This also fixed a bug in
these drivers: they assumed that the height for interlaced formats was
the field height, however height is the frame height. So the height
for a field is actually bt->height / 2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Use the new defines to calculate the full blanking and frame sizes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

It is very common to have to calculate the total width and height of the
blanking and the full frame, so add a few defines that deal with that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Clarify that the il_vfrontporch, il_vsync and il_vbackporch fields must
always be 0 for progressive formats.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>